Moog Videolarm DDW10CR surveillance camera
Contents
1. 96 GKDDWO1 Housing gasket 96 RSORG8 Dome O ring VL 422 Communication Protocol DeputyDome 1 Message Format Data is transmitted at 9600 baud 1 start bit 1 stop bit 8 data bits Isb first no parity The general format for messages sent to the DeputyDome and for inquiry response messages sent by the DeputyDome is shown below BYTE DATA DESCRIPTION Address in hex Camera address 01H 3 to N 1 Command Data All command characters are 8 bit characters most are ASCII characters Terminator and 80H 8FH Most significant bit is always 1 Least significant LS nibble is XOR of all previ Checksum ous bytes LS nibble only except for the leading character F8H The acknowledge message sent from the DeputyDome shall consist of a single hexadecimal 06 character The negative acknowledge message shall consist of a single hexadecimal 15 character Characters enclosed in quotes represent ASCII characters and numbers followed by an H are hexadecimal numbers 2 Message Sequence Each message transaction is initiated by the controller The DeputyDome shall respond to each successfully received message with an ACK message no sooner than 1ms and no later than 20ms after the last byte of the message has been received If the message is not understood by the DeputyDome a NACK message will be sent Ifan inquiry message is successfully received from the host the DeputyDome shall respond with the ACK message as2. 90 BTSECO6 1 4 20X 1 2 Security screw SS 60 1414 Description Qty DDWC10 pan limits collars 50 VL1428 DDWC10 housing body 92 WSFLO1 1 4 Flat washer SS 30 VL1405 DDWC10 accs mounting bracket 92 WSFLO1 1 4 Flat Washer SS 92 WSSLO1 90 BTHH27 1 4 Split lockwasher SS 1 4 20X3 4 Hex head bolt SS 92 WSSLO1 1 4 Split Lockwasher SS 60 4010 14 tooth 1 5 belt drive pulley 90 BTHH32 1 4 20 X 1 2 Hex head bolt SS 60 3012 OMRON SS 5GL2Tr par 00 gt 90 BTRP31 8 32X 3 8 Grounding screw 71 BLEH24 Blower 24VDC 60MM 60 4012 36 tooth 1 5 belt drive pulley DD tilt 70 WPTRAN P2 240 120V 1 5A 24V Transformer 92 WSTHO2 8 Star washer 90 BTSR19 2 56 X 75 Pan head screw 60 3010 Hurst 2RPM pan motor SA SP 91 NTHHO6 8 32 Hex nut SS 76 DDO1PCB DDWC10 Housing PCB 30 VL1509 Limit switch spacer 60 1420 DDWC10 tilt limits collars 76 DDO3PCB DDWC10 pan tilt PC board 90 BTRP19 8 32 X 3 8 Round head screw SS 90 BTRP19 8 32 X 3 8 round head screw SS 30 VL1522 DDW10C Electrical Shield 30 VL1417 DDWC10 liner arms 90 BTRP20 10 32 X 3 8 pan head screw SS 60 1412 DDWC10 tilt bushings 92 WSTH04 10 Star washer 60 1421 DDWC10 tilt shafts DDWC10 Heater 73 CAMTRO1 1 3
3. classe 2 90 vA 3 75Amps Francais CARACT RISTIQUES D APPAREIL PHOTO R solution 470 TVL NTSC 460TVL pal Illumination minimum 1 0 1 0 lux Rapport de bourdonnement 26x 3 5 21mm optiques 321x num rique Format quilibre blanc automobile Obturateur lectronique 22 tapes DDW10CRI1 115 VAC 90 VA 0 8 Amps DDW10CR2 24 VAC Kategorie 2 90 VA 3 75Amps Deutsch KAMERA SPEZIFIKATIONEN EntschlieBung 470 TVL NTSC 460TVL PAL Minimale Ablichtung 1 0 1 0 Lux Summen Verh ltnis 26x 3 5 21mm optisch 321x digital Format Wei e Balance Automobil Elektronischer BlendenverschluB 22 Schritte DDWIOCRI 115 VAC 90 vA 0 8 amp res DDW10CR2 N 24 VAC classe 2 90 vA 3 75Amps Portuguese ESPECIFICACOES DA C MERA Defini o 470 TVL NTSC 460TVL PAL m nima 1 0 1 0 Lux Relacao de zumbido 26x 3 5 91mm ticos 321x digital Formato 7 Contrapeso branco autom vel Obturador eletr nico 22 etapas DDW10CRI1 115 90 vA 0 8 amperi DDW10CR2 N 24 codice categoria 2 90 vA 3 5Amps SPECIFICHE DELLA MACCHINA FOTOGRAFICA Risoluzione 470 TVL NTSC 460TVL pal Illuminazione minima 1 0 1 0 lux Rapporto di zoom 26x 3 5 21mm ottici 321x digitale Disposizione LA Equilibrio bianco automobile Otturatore elettronico 22 punti Italiano Content of Box Loosen all flange nuts and
4. Cableado para el modelo a presi n del receptor PDDW10CR2 C blage pour le mod le pressuris de r cepteur PDDW10CR2 e Verdrahtung f r unter Druck gesetztes Empfangermodell PDDW10CR2 e Fia o para o modelo pressurizado do receptor PDDW10CR2 e Collegamenti per il modello pressurizzato della ricevente PDDW10CR2 US Chart Non Pressurized A Version Red Heater 1 2 Heater Ces Tan i SS o SA S V2 A 3A Or ran S E NALOG IP 36W Blue EE Input 1 Violet Alarm Input 2 Gray Alarm Input 3 Whi hite Alarm common Alarm common 4 7 lt 7 yy 1 VAVAVAVA ka p ya y p A ER bei E Wa Ka Ka Ka p p WA p p Ka vA E WA Vaya Ka WA Kaka WA papa K VAVA al A AA PA pa p V Ka E pa MN These recommended maximum distances for 24VAC with a 10 voltage drop e stos se recomiendan las distancias m ximas para 24VAC con una ca da de voltaje del 10 e Ceux ci sont recommand s des distances maximum pour 24VAC avec une chute de tension de 10 e Diese werden maximale Abst nde fur 24VAC mit einem 10 Spannungsabfall empfohlen Estes sao recomendados dist ncias m ximas para 24VAC com uma queda de tens o de 10 Questi sono suggeriti distanze massime per 24VAC con una differenza de potenziale di 1076 To remove Pan Tilt assembly rmove the dome and liner Afloje el perno cautivo c
5. This is a separate feature from Autotour To record a pattern 1 If the camera is in autotour use the joystick to stop it 2 Clear all customized presets such as preset 1 2 3 etc Note Once the pattern has been recorded the presets can be set again 3 Set preset 80 8 gt 0 gt gt Set to begin recording pattern 1 or set preset 79 to begin recording pattern 2 4 Use joystick to move the camera the movement is recorded 5 Set preset 81 8 gt 1 gt gt Set to stop recording for Pattern 1 or 2 To run a pattern 1 If the camera is in autotour use the joystick to stop it 2 Go to preset 80 8 gt 0 gt Set to run Pattern 1 or go to preset 79 to run Pattern 2 To stop a pattern Move the joystick Note 1 Pattern and Autotour are different processes Make sure to use joystick to stop one before initiating another 2 In case there is a power outage the camera would go to Home position after the power is recovered 3 To erase a recorded pattern just record a new pattern and the old one will be automatically erased Additional Functions Additional functions are available using Goto Preset above the normal preset range The table below describes these functions Part Number 91 NTFLO1 Replacement Parts List DDW10CR PDDW10CR O 9 C 0 Gi 9 De PL Description 3 8 16 Flange Nut d n
6. AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE IN NO EVENT SHALL VIDEOLARM BE LIABLE TO PURCHASER FOR ANY SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING BUT NOT LIMITED TO COMPENSATION REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER Electrical Specifications Camera with hardwire pan tilt Power Source 8 Power Consumption DDW10CR includes heater blower and camera PDDW10CR Ny DDW10CRI 115 VAC 90 vA 0 8 Amps DDW10CR2 N 24 VAC Class 2 90 vA 3 75Amps 1 N Network model CAMERA SPECIFICATIONS Resolution 470 TVL NTSC 460TVL PAL Minimum Illumination 1 0 1 0 Lux Zoom Ratio 26x 3 5 21mm optical 321x digital Format White Balance Auto Electronic Shutter 22 steps English DDW10CRI 115 VAC 90 vA 0 8 amperios DDW10CR2 N 24 VAC clase 2 90 VA 3 75Amps Espa ol ESPECIFICACIONES DE LA CAMARA Resoluci n 470 TVL NTSC 460TVL PAL Iluminaci n m nima 1 0 1 0 lux Cociente de zumbido 26x 3 5 21mm pticos 321x digital Formato 4 Equilibrio blanco autom vil Obturador electr nico 22 pasos DDWIOCRI 115 VCA 90 vA 0 8 ampere DDW10CR2 N 24
7. CCD AF 16X ZOOM 12VDC NTSC 96 RSORNG 1 4 O ring 30 VL1415 DDWC10 Camera Bracket RCDWW10 Clear dome for DeputyDome 90 BTSMO1 1 5mm X 6mm Sheet metal screw SS 90 BTSECO4 1 4 20 x 3 8 security screws 90 BTRP20 10 32 X 3 8 PN HD PHIL SS 90 BTHH33 5 16 18 X 3 4 Hex head bolt SS 92 WSSLO2 5 16 Split Lockwasher SS 30 VL1419 90 BTBS04 DDWC10 tilt bracket 10 32x1 2 Button Head screw SS 30 VL1408 DDWC10 P T Quick release bkt 92 WSTH04 10 Star washer 96 MPDDW Pan tilt mounting pad 27 WDDW10 DDWC10 window DDWC10 pan tilt 30 VL1313 DDWC10 rotating liner 30 VL1418 90 BTBSO5 DDWC10 tilt liner 10 32x 1 1 4 Button Head screw SS 95 FSCO4 10 32X1 2 Captive screw 60 4014 62 tooth 1 5 timing belt tilt DDWC10 bearing assembly 90 BTBS04 10 32x1 2 Button Head screw SS 60 4011 18 tooth 1 5 belt drive pulley 60 4015 55 tooth 1 5 timinig belt pan 90 BTBSO8 50 VL1430 1 4 20X 1 2 Button Head screw SS DDWC10 wall mount 60 4013 36 tooth 1 5 belt drive pulley DD pan 90 BTSECO6 1 4 20X 1 2 Security screw SS 90 BTHH37 8 32 X 1 2 Trimmed hex head SS 96 GKDDWM Access cover gasket 92 WSTHO2 8 Star washer 30 VL1431 DDWC10 Wall Mount access cover 30 VL1411 DDWC10 P T bracket 90 BTSECO5 10 32X 1 2 Security screw
8. b 10 11 12 13 14 15 16 The installation should be made by a qualified installer The installation should be in compliance with local codes Care should be exercised to select suitable hardware to install the unit taking into account both the composition of the mounting surface and the weight of the unit Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety When the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachment accessories specified by the manufacturer Use only with a cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over Unplug this apparatus during lighting storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when
9. literatura que acompa a la aplicaci n Ce symbole de point d exclamation est pr vu pour alerter l utilisateur la presence des instructions importantes dans la litt rature accompagnant l appareil Dieses Ausruf Punktsymbol soll den Benutzer zum Vorhandensein de wichtigen Anweisungen in der Literatur alarmieren die das Gerdt begleitet Este s mbolo do ponto do exclamation pretendido alertar o usu rio presen a de instru es importantes na literatura que acompanha o dispositivo Questo simbolo del punto del exclamaton inteso per avvertire l utente alla presenza delle istruzioni importanti nella letteratura che accompagna l apparecchio USA PRIDE LIMITED WARRANTY For viDEOLARM INC PRODUCTS VIDEOLARM INC warrants this Product to be free from defectsin material or workmanship as follows PRODUCTCATEGORY PARTS LABOR All Enclosuresand Electronics Five 5 Years Five 5 Years Pan Tilts Three 3 Years 6 months if used in autoscan Three 3 Years 6 months if usedin autoscan Poles PoleEvators Three 3 Years our operation Three 3 Years tour operation Warrior Q View l R lluminators Five 5 Years Five 5 Years SView Series Five 5 Year 6 months if usedin autoscan Five 5 Years 6 months if usedin autoscan Controllers Five 5 Years tour operation Five 5 Years tour operation Power Supplies Five 5 Years Five 5 Years AccessoryBrackets Five 5 Years Five 5 Years During the labor w
10. previously described and the inquiry response shall then be transmitted no sooner than 1ms and no later than 100ms after the transmission of the ACK 3 Command Messages These commands control the basic motion of the pan tilt platform and the lens movement of the camera system Byte number 1 is the start of message F8 byte number 2 is the device address default 01 and byte number five is the message terminator byte 3 1 Motion Command Messages FUNCTION Byte 3 Byte 4 DESCRIPTION meme be mme EES won fe fo Foose CI CCT CN E CT SE EE CET CN E S IRIS STOP S PAN LEFT AT SPEED x 0 Pan left at speed index 0 15 l is lower case L PAN RIGHT AT SPEED x Pan right at speed index 0 15 TILT UP AT SPEED x Tilt up at speed index 0 15 TILT DOWN AT SPEED x ER SM Tilt down at speed index 0 15 3 2 Preset Command Messages These commands control the position presets and some of the operational parameters of the pan tilt platform Byte number 1 is the start of message F8 byte number 2 is the device address default 01 and byte number five is the message terminator byte Note that preset 63 is reserved for another function this preset number is used in the commands P and H FUNCTION Byte 3 Byte 4 DESCRIPTION GOTO PRESET POSITION han SAVE PRESET POSITION 5 CLEAR PRESET SE Presets 1 63 01H 40H Cle
11. 1 yes bit4 bit7 0011 30H 31H bitO Isb aux output 0 off 1 on Terminator and 80H 8FH Most significant nibble is always 8 Least significant LS nibble is the XOR of all Checksum previous bytes LS nibble only except for leading autobaud character F8H 3 11 Sensor Feedback Commands FUNCTION Byte 3 Byte 4 DESCRIPTION REQUEST SENSOR DATA SCH Ee Get pressure and temperature data The response to this command is shown in the table below DATA DESCRIPTION Address in hex Camera address 01H DFH pel SS P1 MS nibble 30H Pressure data is 30H ored with data nibble 3FH 7 PO6 PO5 P04 of pressure data PO LS nibble Pressure data is 30H ored with data nibble 30H 3FH PO2 P01 POO of pressure data T1 MS nibble Temperature data is 30H ored with data nibble 30H 3FH T07 TO6 TO5 TO4 of temperature data TO LS nibble Temperature data is 30H ored with data nibble 30H 3FH T03 TO2 TO1 TOO of temperature data Terminator and 80H 8FH Most significant nibble is always 8 Least significant LS nibble is the XOR of all Checksum previous bytes LS nibble only except for leading autobaud character F8H Not supported on DeputyDome Product Registration Warranty Thank you for choosing Videolarm We value your patronage and are solely committed to providing you with only the highest quality products available with unmatched customer service levels that are second to n
12. 1 14 1 REQUEST POSITION GE position ASCII character upper case p followed by the 2 character The response to this command is shown in the table below BYTE DATA DESCRIPTION Address in hex Camera address 01H DFH A2 MS nibble 30H Position data is 30H ored with data nibble A11 A10 09 08 of azimuth data Al Position data is 30H ored with data nibble 30H 3FH A07 A06 A05 A04 of azimuth data AO LS nibble Position data is 30H ored with data nibble 30H 3FH A03 A02 A01 AOO of azimuth data E2 MS nibble Position data is 30H ored with data nibble 30H 3FH E11 E10 E09 E08 of elevation data El Position data is 30H ored with data nibble 30H 3FH 207 E06 E05 E04 of elevation data EO LS nibble Position data is 30H ored with data nibble 30H 3FH E03 E02 E01 E00 of elevation data Terminator and 80H 8FH Most significant nibble is always 8 Least significant LS nibble is the XOR of all Checksum previous bytes LS nibble only except for leading autobaud character F8H 3 7 GoTo Lens Position Commands This command causes the lens to go to an absolute position based on the motor encoders The GOTO LENS POSITION 15 shown in its complete form in the following table BYTE DATA DESCRIPTION Address in hex Camera address 01H DFH AS Se SS x l Z2 MS nibble 30H Position data is 30H ored with data nibble S 211 210 209 208 of zoom lens posit
13. 5 Address SW1 sw2 sw3 SW4 sws swe Off Off Off On On Off On 20 On On Off On Off On 21 Off On Off On Off On 23 Off Off Off On Off On 25 Off On On Off Off On 26 On Off On Off Off On 27 Off Off On Off Off On 28 On On Off Off Off On 29 Off On Off Off Off On 30 On Off Off Off Off On Off Off Off Off Off On The dipswitches come factory preset with switch 6 in the on position indicating the address mode The default address for the pan tilt on receiver driver ver sions of the DeputyDome is preset at the factory as 1 If more than one unit is being used with 485 control it will be necessary to change the address for each additional unit UNIT ADDRESSES FOR 485 CONTROL To change the address power down the unit remove the pan tilt from the housing and set the address using the dipswitch settings shown in Chart 1 in the next column Replace the unit and power up UNIT PARAMETERS Alarm sense camera on screen display and baud rate can all be controlled by the dipswitches The alarm sense can be set to accept either contact closures NO or contact openings NC as the alarm condition The camera on screen display will show icons on the monitor when zoom focus and iris are used Factory presets are contact closures for the alarm sense off for the camera on screen display and 9600 baud To change parameters p
14. MOOC O 2009 2010 Moog Videolarm Inc All Rights Reserved gt BEER Product Information for IP Ready Software 13005521124 www videolarm com Deputy Dome Bullet Resistant Standard Pressurized Dome www videolarm com Installation and Operation Instructions for the following models DDW10CR1 DeputyDome Series 10 gauge Steel Bullet Resistant Outdoor dome PTZ Camera System with 26x Day Night Camera onboard receiver driver 120VAC heater Tough enough to stop a 9mm bullet PDDW10CR1 Pressurized Version DeputyDome Series 10 gauge Steel Bullet Resistant Outdoor dome PTZ Camera System with 26x Day Night Camera onboard receiver ERE driver 120VAC heater Tough enough to stop a 9mm bullet CERTIFIED Before attempting to connect or operate this product 81 IN5210 please read these instructions completely 10 07 2010 IMPORTANT SAFEGUARDS Oc Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with damp cloth Do not block any of the ventilation openings Install in accordance with the manufacturers instructions Cable Runs All cable runs must be within permissible distance Mounting This unit must be properly and securely mounted to a supporting structure capable of sustaining the weight of the unit Accordingly a
15. O LS nibble Position data is 30H ored with data nibble 30H 3FH A03 02 01 00 of azimuth data A2 MS nibble 30H Position data is 30H ored with data nibble 3FH A11 A10 09 08 of azimuth data E2 MS nibble Position data is 30H ored with data nibble 30H 3FH E11 E10 E09 E08 of elevation data El Position data is 30H ored with data nibble 30H 3FH 207 E06 E05 E04 of elevation data Terminator and 80H 8FH Most significant bit is always 1 Least significant LS nibble is the XOR of all Checksum previous bytes LS nibble only except for leading autobaud character F8H EO LS nibble Position data is 30H ored with data nibble 30H 3FH E03 202 E01 E00 of elevation data Notes on Goto position command Pan position has a range of 0 2880 This represents the range of 0 to 360 degrees in steps of 15 degree A pan position of 000 represents the home position Tilt position has a range of 0 to 950 This represents a range of 0 to 95 degrees in steps of 10 degree Position 0 is the maximum down position and position 950 is the maximum up horizontal position Home position is at 450 3 6 Position Feedback This command causes the platform to report the current pan and tilt position based on the motor encoders Byte number 1 is the start of message F8H byte number 2 is the device address default 01 and byte number five is the message terminator byte FUNCTION Byte 3 Byte 4 DESCRIPTION
16. ar preset position from memory CLEAR ALL PRESETS Clears all presets from memory AUTO TOUR ON Enables the auto tour Any pan left or pan right will turn off the auto tour 3 3 Preset Response Message FUNCTION DESCRIPTION 01H 40H Currently at preset 01H 40H PRESET INQUIRY RESPONSE I Inactive not at preset EP E Error unable to go to preset 3 4 Address Assignment Message This six byte command sets the address of the dome The address is in hexadecimal and is contained in bytes 4 and 5 If the address is set to FFH then the unit derives its address from the dipswitch Byte number 1 is the start of message F8 byte number 2 is the device address default 2 01 and byte number six is the message terminator byte FUNCTION Byte 4 Byte 5 DESCRIPTION Set unit address Byte 4 contains the ms nibble of address and Byte 5 contains Is nibble of address ASSIGN UNIT ADDRESS 30H 3FH 30H 3FH Example Set address of unit 1 to 53 decimal 35H F8H 01H 41H 33H 35H 86H 3 5 Goto Position Message This command causes the platform to go to an absolute position based on the motor encoders The GOTO POSITION command is longer than the preceding command messages and is shown in its complete form in the following table BYTE DATA DESCRIPTION Address in hex Camera address 01H FFH Al Position data is 30H ored with data nibble A07 A06 A05 A04 of azimuth data A
17. arranty period to repair the Product Purchaserwill either return the defective product freight prepaid or deliver it to Videolarm Inc Decatur GA The Productto be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with a Return Materials Authorization number displayed on the outer box or packing slip To obtain a RMA you must contact our Technical Support Teamat 800 554 1124extension 101 Videolarm will return the repaired Productfreight prepaid to PurchaserVideolarm is not obligated to provide es a substitute unit during the warranty period or at any time After the applicable warranty period Purchasermust pay all labor and or par The limited warranty stated in these product instructions is subject to all of the following terms and conditions TERMS AND CONDITIONS 1 NOTIFICATIONOF CLAIMS WARRANTY SERVICE If Purchaser believes that the Product is defective in material or workmanship then written notice with an explanation of the claim shall be given promptly by Purchaser to Videolarm but all claims for warranty service must be made within the warranty period If after investigation Videolarm determines that the reported problem was not covered by the warranty Purchaser shall pay Videolarm for the cost of investigating the problem at its then prevailing per incident billable rate No repair or replacement of any Product or part thereof shall extend the warranty period as to
18. cht werden Afrouxe todas as porcas da flange e gire a carcaca no sentido hor rio para remover a carcaca da montagem A montagem da parede pode agora ser unida parede Allenti tutti i dadi della flangia e giri l alloggiamento in senso orario per rimuovere l alloggiamento dal supporto Il supporto della parete pu ora essere fissato alla parete After the wall mount is securely attached to the wall remove the tamper resistant screws and take off the access plate Despu s de que el montaje de la pared se una con seguridad a la pared quite los tornillos resistentes del pis n y saque la placa del acceso Apres que le de mur soit solidement fix au mur enlevez les vis r sistantes de bourreur et enlevez le plat d acc s Nachdem die Wandeinfassung sicher zur Wand angebracht ist entfernen Sie die best ndigen Schrauben des Besetzers und entfernen Sie die Zugang Platte Depois que a montagem da parede unida firmemente parede remova os parafusos resistentes da calcadeira e retire a placa do acesso Dopo che il supporto della parete sia fissato saldamente alla parete rimuova le viti resistenti del compressore e tolga la piastra di accesso am L mm SIN Wiring for DDW10CR e Cableado DDWIOCR e C blage pour DDWIOCR e Verdrahtung fur DDW10CR e Fia o para DDWIOCR e Collegamenti per DDW10CR Wiring for Pressurized Receiver model PDDW10CR2
19. he guage or regulator from 10 20psi 7 1 4bar Al presurizar la unidad sea seguro fijar la medida o el regulador de 10 20psi 7 1 4bar En pressurisant l unit soyez s r de placer la jauge ou le r gulateur de 10 20 7 1 4bar Wenn Sie MaBeinheit unter Druck setzen seien Sie sicher das EichmaB oder den Regler von 10 20psi 7 1 4bar einzustellen Ao pressurizar a unidade seja certo ajustar o guage ou regulador de 10 20psi 7 1 4bar Nel pressurizzare l unit sia sicuro regolare il misuratore o il regolatore da 10 20psi 7 1 4bar Open the relief valve Drain all air from the housing and repeat twice to remove all moisture Abra la v lvula de descarga Drene todo el aire de la cubierta y de la repetici n dos veces para quitar toda la humedad Ouvrez la soupape de s curit vacuez tout l air le logement et la r p tition deux fois pour enlever toute l humidit Offnen Sie das Sicherheitsventil Lassen Sie alle Luft aus dem Geh use und der Wiederholung zweimal ab um alle Feuchtigkeit zu entfernen Abra a v lvula de escape Drene todo o ar da carcaca e do repeat duas vezes para remover toda a umidade Apra la valvola di sfiato Vuoti due volte tutta l aria dall alloggiamento e dalla ripetizione per rimuovere tutta l umidit Place the air chuck on the tank valve and begin filling until pressure relief valve opens Coloque la tirada del aire en la v lvula del tanque y comience a llenar hasta que la v
20. hin an equilateral triangle is intended to alert the user to the presence of non insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk to persons Este simbolo se piensa para alertar al usuario a la presencia del voltaje peligroso no aislado dentro del recinto de los productos que puede ser un riesgo de choque el ctrico Ce symbole est pr vu pour alerter l utilisateur la presence de la tension dangereuse non isol e dans la cl ture de produits qui peut tre un risque de choc lectrique Dieses Symbol soll den Benutzer zum Vorhandensein der nicht lsolier Gef hrdungsspannung innerhalb der ProdukteinschlieBung alarmieren die eine Gefahr des elektrischen Schlages sein kann Este s mbolo pretendido alertar o usu rio presenca di tens o perigosa non isolada dentro do cerco dos produtos que pode ser um risco de choque el trico Questo simbolo inteso per avvertire l utente alla presenza di tensione pericolosa non isolata all interno della recinzione dei prodotti che puo essere un rischio di scossa elettrica The exclamation point within an equilateral triangle is intended to alert the user to presence of important operating and maintenance servicing instructions in the literature accompanying the appliance Este s mbolo del punto del exclamation se piensa para alertar al usuario a la presencia de instrucciones importantes en la
21. ion data 5 21 Position data is 30H ored with data nibble 30H 3FH 207 206 205 204 of zoom lens position data ZO LS nibble Position data is 30H ored with data nibble 30H 3FH 203 202 201 200 of zoom lens position data 7 F2 MS nibble Position data is 30H ored with data nibble 30H 3FH F11 F10 F09 FO8 of lens focus position data F1 Position data is 30H ored with data nibble 30H 3FH F07 FO6 FO5 F04 of lens focus position data FO LS nibble Position data is 30H ored with data nibble 30H 3FH F03 F02 F01 FOO of lens focus position data 80H 8FH Most significant nibble is always 8 Least significant LS nibble is the XOR of all Checksum previous bytes LS nibble only except for leading autobaud character F8H Terminator and 3 8 Lens Position Feedback Commands Byte 3 Byte 4 REQUEST POSITION aye DESCRIPTION Get position ASCII character V followed by the 72 character The response to this command is shown in the table below BYTE DATA DESCRIPTION Address in hex Camera address 01H DFH EE SS Position data is 30H ored with data nibble Z2 MS nibble 30H 3FH 211 210 209 208 of zoom lens position data Z1 Position data is 30H ored with data nibble 30H 3FH 207 206 205 204 of zoom lens position data ZO LS nibble Position data is 30H ored with data nibble 30H 3FH 203 202 201 200 of zoom lens position data F2 MS nibble Position data is 30H
22. lvula de descarga de presi n se abre Placez le manarin d air sur la valve de r servoir et commencez remplir jusqu ce que la valve de d compression s ouvre Setzen Sie die Luftklemme auf das Behdlterventil und fangen Sie an zu f llen bis DruckablaBventil sich ffnet Coloque o mandril do ar na v lvula do tanque e comece a encher se at que a v lvula de escape de press o abra Disponga il mandrino dell aria sulla valvola del carro armato e cominci a riempirsi fino a che la valvola limitatrice della pressione non si apra After purging check the housing pressure It should be around 5psi 34bar Desraws ple Oe ee eo de la cero Debe eur olrecedo de Sma plo ARS E pure du COTES lo presion de Elie cero ire carica de Sea D reg Hocem Uber dum der Geno Leer ck bere worden ni Xie safe um pa Epipor sem Ap fer EENEG verfogoc DI Cho COREL Deve ser erm Ima de scu bar ope TERTIA delrceppo del coniroida la presione 4 GO DOmTebbe PREE TRING O So 34 cir 20 CHANGING SETTINGS FOR RECEIVER DRIVER UNITS RH H Jl tit 656 CR TO HOTE DIPSWITCHES The dipswitches serve a dual purpose First they control the address of the pan tilt when operated via RS485 Second they control the alarm and display functions for the pan tilt Address changes are made using the dip switches located on the PC board 21 CHART 1 RECEIVER DRIVER PAN TILT ADDRESSES 19 SW
23. nes de la vivienda Pour joindre la plupart des inserts d me aligner correctement avec le logement So h ngen die meisten Eins tze Kuppel Angleichung richtig mit Gehduse Para anexar c pula insere mais alinhar corretamente com habita o Per allegare cupola inserti allineare correttamente con la maggior parte degli alloggi If Lanyard attaches to both trim ring and the outside of the housing Si Lanyard concede a ambos y el anillo exterior de la vivienda Si Lanyard attache la fois l assiette et le ring ext rieur de l habitation Wenn Lanyard misst sowohl trim Ring und die auBerhalb des Gehduses Se colhedor atribui a ambos os an is e os remates de fora da habitacao Se Lanyard attribuisce ad entrambi i trim anello e l esterno del corpo Align insert and install dome Alinear insertar e instalar c pula Alignez et installez ins rer d me Richten Sie einf gen und installieren Kuppel Alinhar inserir e instalar c pula Allineare inserire e installare cupola To pressurize unit remove wall mount access cover Para presionar a la unidad extraiga el montaje en pared cubierta de acceso De faire pression sur l unit retirer l acc s couvrir murale Um Druck Einheit entfernen Wandhalterung Abdeckung Para pressionar unidade remova parede montar acesso cobrir Per pressurizzare unit rimuovere il montaggio a parete coperchio di accesso Air Chuck 7 Nitrogen Tank When pressurizing unit be sure to set t
24. omo se muestra Para eliminar Pan Inclinaci n rmove montaje de la c pula y de l nea Desserrez pistolet comme le montre Pour supprimer Pan Tilt rmove montage du d me et doublure L sen Sie Bolzenschuss wie So entfernen Sie Pan Tilt rmove Montage der Kuppel und Linienkonfer enzen Afrouxe bolter cativeiro como mostrado Para remover Pan Tilt rmove montagem da c pula e forro Allentare bullone in cattivita come mostrato Per rimuovere Pan Tilt rmove assemblaggio e la cupola di linea Lift up on Pan Tilt assembly to remove Afloje el perno cautivo como shownSlide Pan Inclinaci n atr s hasta que quede alineada con las pesta as Levante de Pan Inclinaci n de montaje para eliminar Desserrez pistolet comme shownSlide Pan Tilt revenir jusqu ce qu il Soulevez le Pan Tilt d assemblage pour enlever s aligne avec les onglets Heben Sie auf Pan Tilt Montage zu entfernen L sen Sie Bolzenschuss als shownSlide Pan Tilt zur ck bis sie im Einklang mit den Registerkarten Levante ont rio Pan Tilt montagem para remover Afrouxe bolter cativeiro como shownSlide Pan Tilt para tr s at que Sollevare il Pan Tilt assemblaggio di rimuovere alinha com os separadores Allentare bullone in cattivit come shownSlide Pan Tilt indietro sino a che non si allinea con le schede NOTE Position To attach dome inserts most align properly with housing Para adjuntar c pula alinear correctamente la mayor a de las insercio
25. one in the security industry v Should a problem arise rest assure that Videolarm stands behind its products gt ds by offering some of the most impressive warranty plans available 3 Years lt on all Housings Poles Power Supplies and Accessories and 5 Years on wt all camera systems SView QView Warriors and InfraRed llluminators 27 ARR Register Your Products are Option 1 Online Option 2 Mail In hy E Take a few moments and validate your purchase with our Online Product Registration Form a WWW Videolarm com productregistration jsp or complete and mail in the bottom portion of this flyer Register your recent Videolarm purchases and benefit from the following Simple and Trouble Free RMA process Added into customer database to receive product updates news e Eliminate the need to archive original purchase documents Receipts Purchase Orders etc S Cut at the dotted Line ee ee A A ge Q3 et Zoe A Place in envelope affix stamp and mail to Videolarm ATTN Warranty 2525 Park Central Ave Main Contact Info Decatur GA 30035 First Name Last Name Professional Title Company Address 1 Address 2 City State Province Country Zip Postal Code Phone Number E mail Address Please Circle One Business Personal Product Information Name amp Location of Company Store where Purchased City State Country Videolarm Product ID Product De
26. ored with data nibble 30H 3FH F11 F10 FO9 FO8 of focus data F1 Position data is 30H ored with data nibble 30H 3FH 207 206 205 204 of focus data FO LS nibble Position data is 30H ored with data nibble 30H 3FH 203 202 201 FOO of focus data Terminator and 80H 8FH Most significant nibble is always 8 Least significant LS nibble is the XOR of all 9 Checksum previous bytes LS nibble only except for leading autobaud character F8H 3 9 Latch Commands The camera commands control parameters of camera operation All the Camera commands generate a Latch Status response message FUNCTION Byte 3 Byte 4 DESCRIPTION Toggles iris operation between auto iris and manual iris CAMERA POWER TOGGLE E Toggles camera operation on and off LENS SPEED TOGGLE Toggles between high speed and low speed zoom TOGGLE AUX1 1 i Toggles AUX1 output Also puts camera into auto white AUTO WHITE BALANCE balance INCREASE BLUE GAIN Increase Blue recor ND in camera INCREASE RED GAIN Increase Increase Red gain in camera gain in camera STOP COLOR GAIN o e Stop Red Blue increase PRESET STATUS REQUEST Requests current camera status 3 10 Latch Status Response Message DESCRIPTION FBH Sne character 1 6 Address hex Camera address 01H DFH bitO Isb Auto Iris 0 auto 1 manual bit Camera power 0 off 1 on 4 30H 38H bit2 Lens speed 0 slow 1 fast bit3 Comm error 0 no
27. ower down the unit remove the pan tilt from the housing and set the desired parameter using switches 1 and 2 as directed in chart 2 below Replace the unit and power up In UTC mode there is nothing further to do However if you re operating in 485 mode you must reset the address AFTER POWERING BACK UP following the instructions above CHART 2 PARAMETER DIP SWITCH SETTINGS Switch Settings awe Address data On Closed TE M 000 0 0 0 0 0 0 0 0 00 O Switch Settings Parameters Off open On E No Operation Erase EEPROM On off BAUD RATE On 9600 Off 4800 ALARM On NC Off NO DISPLAY On Display on Off Display off Erasing the EEPROM will override the other switch settings If the EEPROM is erased power the unit off the switches to the desired baudrate alarm position and display mode with SW4 and SW5 ON and SW6 OFF then power the unit on again Finally power the unit off set the address and make sure that SW6 is ON power the unit on and begin normal operation Autotour CONTROL FUNCTIONS Zoom Focus and Iris Using the manual focus commands leaves the unit in manual focus mode Using the manual iris commands will leave the unit in manual iris mode as well Zooming the camera will restore the camera to auto focus and auto iris Goto preset 89 will also restore auto focus and auto iris Protocols The DeputyDome is commanded electrically via RS 485 4 wire protocol The transmitter is disabled when not in
28. scription Serial Available only for Camera Systems IR Illuminators Wireless Devices PO
29. shed environmental and electrical parameters or if such Product s original identification trademark serial number markings have been defaced altered or removed Videolarm excludes from warranty coverage Products sold AS IS and or WITH ALL FAULTS and excludes used Products which have not been sold by Videolarm to the Purchaser All software and accompanying documentation furnished with or as part of the Product is furnished AS 15 i e without any warranty of any kind except where expressly provided otherwise in any documentation or license agreement furnished with the Product 4 PROOF OF PURCHASE The Purchaser s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility DISCLAIMEROF WARRANTY EXCEPT FOR THE FOREGOING WARRANTIES VIDEOLARM HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO ANY AND OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND OR ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2 312 3 OF THE UNIFORM COMMERCIAL CODE AND OR IN ANY OTHER COMPARABLE STATE STATUTE VIDEOLARM HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON VIDEOLARM PRODUCTS OR NON VIDEOLARM RECOMMENDED PRODUCTS PURCHASER CHOOSES TO CONNECT TO PRODUCT LIMITATION OF LIABILITY THE LIABILITY OF VIDEOLARM IF ANY AND PURCHASER S SOLE
30. the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled of objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Be sure to periodically examine the unit and the supporting structure to make sure that the integrity of the installation is intact Failure to comply with the foregoing could result in the Unit separating from the support structure and falling with resultant damages or injury to anyone or anything struck by the falling unit UNPACKING Unpack carefully Electronic components can be damaged if improperly handled or dropped If an item appears to have been damaged in shipment replace it properly in its carton and notify the shipper Be sure to save 1 The shipping carton and packaging material They are the safest material in which to make future shipments of the equipment 2 These Installation and Operating Instructions SERVICE If technical support or service is needed contact us at the following number TECHNICAL SUPPORT AV AILABLE 24 HOURS 1 800 554 1124 SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER BACK NO USER SERVICE ABLE PARTS INSIDE REFER SEVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with an arrowhead symbol wit
31. the entire Product The specific warranty on the repaired part only shall be in effect for a period of ninety 90 days following the repair or replacement of that part or the remaining period of the Product parts warranty whichever is greater 2 EXCLUSIVE REMEDY ACCEPTANCE Purchaser s exclusive remedy and Videolarm s sole obligation is to supply or pay for all labor necessary to repair any Product found to be defective within the warranty period and to supply at no extra charge new or rebuilt replacements for defective parts 3 EXCEPTIONS TO LIMITED WARRANTY Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the warranty period which is subjected to any of the following abuse improper use negligence accident lightning damage or other acts of God i e hurricanes earthquakes modification failure of the end user to follow the directions outlined in the product instructions failure of the end user to follow the maintenance procedures recommended by the International Security Industry Organization written in product instructions or recommended in the service manual for the Product Furthermore Videolarm shall have no liability where a schedule is specified for regular replacement or maintenance or cleaning of certain parts based on usage and the end user has failed to follow such schedule attempted repair by non qualified personnel operation of the Product outside of the publi
32. turn the housing clockwise to remove the housing from the mount The wall mount can now be attached to the wall Remove 2 tamper resistant with the security tool provided in the packet Quite 2 a pis n resistente con la herramienta de la seguridad proporcionada en el paquete Enlevez 2 le bourreur r sistant avec l outil de s curit fourni dans le paquet Entfernen Sie 2 den Besetzer der mit dem Sicherheit Werkzeug best ndig ist das im Paket bereitgestellt wird Remova 2 a calcadeira resistente com a ferramenta da seguranca fornecida no pacote Rimuova 2 il compressore resistente con l attrezzo di sicurezza fornito nel pacchetto Cubierta de perno con seguridad a la pared o al poste Logement de boulon solidement au mur ou au poteau Schraubbolzen Gehduse sicher zur Wand oder zum Pfosten Carcaca de parafuso firmemente parede ou ao p lo Alloggiamento di bullone saldamente alla parete o al palo Afloje todas las tuercas del reborde y d vuelta a la cubierta a la derecha para quitar la cubierta del montaje El montaje de la pared se puede ahora unir a la pared D tachez tous les crous de bride et tournez le logement dans le sens des aiguilles d une montre pour enlever le logement du b ti Le b ti de mur peut maintenant tre fix au mur L sen Sie alle Flanschn sse und drehen Sie das Geh use nach rechts um das Geh use von der Einfassung zu entfernen Die Wandeinfassung kann zur Wand jetzt angebra
33. use to allow multiple camera systems to be tied to the same response pair Control protocols supported are VL 422 detailed in the Appendix and Pelco P and Pelco D The DeputyDome will automatically sense which protocol is being used and respond to it Baud rates of 9600 factory default and 4800 are available See the Unit Pa rameters section above for instructions on setting the baud rate Presets The DeputyDome has 64 presets that can be used individually or as part of an autotour To program a preset set the pan tilt Zoom focus and backlight compensation settings to the desired value Issue the command to store program the preset number using an appropriate controller See the Appendix When the Goto Preset number command is given the system will move to the stored pan tilt Zoom focus and backlight settings at the highest available speed Preset Number Function Backlight Compensation On The Autotour function causes the camera to automatically go in sequence to each preset that has been programmed into the PTZ The dwell time at each preset position can be individually set to be from 0 to 99 seconds See the Menu Driven Settings section to learn how to set dwell time The Autotour will continue until a pan or tilt command is given If the unit loses power while in Autotour Autotour will be resumed when power is restored Pattern The DeputyDome allows recording of two patterns with each pattern being up to 2 minutes in length
Download Pdf Manuals
Related Search