NEC NP03WK
Contents
1. 2 Use the two supplied M5 5x9 5 screws to securely attach the supplied plate B to the arm Plate B If plate B is not installed the projector may slide out of the arm and fall off which may cause injury Adjusting the Projection Position E Preparations Before adjusting Project an image from the projector then first use the focus lever of the projector to roughly adjust the focus of the projected image For information on how to project an image see Installation and Connections and Projecting an Image Basic Operation in the user s manual included with the projector e From the on screen menu select Ceiling Front as the method of projection 1 Check the tilt adjust Knobs Projector fixation plate Verify that the four tilt adjust knobs are all set to the same adjustment height If the projector fixation plate is slanted correct vertical adjustment and horizontal adjustment cannot be performed 2 Adjust the size of the projected image and the left right tilt The illustrations in this manual show the adjustment for an image with a 4 3 aspect ratio Connecting cables for screen and projector are omitted Adjust the size of the projected image and if necessary the tilt in clockwise or anticlockwise direction 1 Loosen the vertical adjust arm fixation knobs Loosen the two knobs shown in black in the illustration 2 Move the projector back and forth to match th2. NPO2WK amp NPO3WK Installation and Adjustment Manual NEC Display Solutions Ltd NEC Wall Mount Unit Installation and Adjustment Manual Thank you for your purchase of this NEC wall mount unit Please read this installation and adjustment manual carefully to ensure proper use The Wall Mount Unit NPO2ZWK NPO3WK is exclusivelyfor Projector NP M260XS M300XS M350XS M260WS M300W_ and cannot be used for other projectors Special skills are required to install the pojector This work A N should never be performed by the customer To the Dealer and Installer To ensure customer safety we ask that the installation work be started after careful attention is paid to the strength of the mounting location to ensure it will withstand the weight of the projector and mounting hardware CONTENTS Please heed the following cccecccseceeeeecseeeeeeeeseeteeeeaeees 1 Preparation n s eseenenononennenenennrnnnrnrnrrnernrenerrnrnrrrererenenrnrnrnn gt 4 Packaged FAIS ae ce pee cpa rap ptesaiene sonnei na eapicatenss a sarexne nae 4 Names Of Parts c ccccccseceeeeeeeeeeeeeeeeseeeeeaeeeaeeeeaees s Dimensions of Parts ccccccccccccseeeeceeeeeeeeseueeeeneaeees 6 Mounting the Projector ccccccsccseceeceeseeseeseeeaeecseaeeeaes Adjusting the Projection Position 0 c cccceseseseeeeeseeeeneee 10 SPECINCAON oe en satnncaye Senne vas wares ound aeiemeageungacamaneatediawen es 13
3. 1245 maximum E gt m D il T ES 490 850 7 C i NI bu e T HE Projector bottom surface including the legs Mounting the Projector Preparations 1 Determine the installation location of the screen and accordingly decide the installation position of the wall mount unit Refer to the section Installation in the user s manual included with the projector for more information e Installation for slanted projection is not possible Determine the position for frontprojection 2 Make sure that all conditions described in the section Heed the Following on page 2 of this manual are met e Because the M260XS M300XS M350XS M260WS M300WS have a large optical axis elevation angle a slight shift in projection distance will have a large effect on the screen size and position If the projector angle is off image distortion will increase 1 Align the projector adapter with the holes on the bottom of the projector and securely attach the adapter with the four supplied screws M4x20 2 Loosen the vertical adjust arm fixation knobs of the projector adapter Vertical adjust arm fixation knobs T If screws other than the supplied ones are used the projector may be seriously damaged or the projector may fall and cause injury Be sure to use only the supplied screws 2 Attach the wall adapter to the structural material of the wall To ensure a projected image without di
4. Please heed the following Symbol In this Installation and Adjustment Manual to ensure the safe and proper use of the product prevent harm to yourself and others and damage to property various symbols are used The symbols and meanings are as follows Please read this manual after ensuring the contents are well understood Improper handling and ignoring this indication may result in A N Warning bodily harm such as death serious injury and so on A Cauti Improper handling and ignoring this indication may result in SA CEEA bodily injury and damage to surrounding contents Examples of symbols Symbol alerts you to cautions including warnings Concrete cautions are specified in figures S Symbol expresses prohibited actions Concrete prohibitions are specified in figures symbol expresses compulsory actions Concrete instructions are specified in figures e When installing the projector and adjusting the projection position be sure to do so Q as explained in this manual The projector may fall and cause injury if installed and adjusted improperly sufficient strength to support the combined weight about 13 kg of the projector about 4kg the wall mount unit about 9 kg and so on for an extended period as well as to withstand earthquakes Insufficient strength or fastening may result in the projector falling and causing injury Q e To prevent the projector from falling install it in a location and faste
5. e projector is turned on Doing so could damage your eyesight Do not hang from the projector and the Wall Mount Unit Doing so may result in the projector and the Wall Mount Unit falling and causinginjury Be especially careful of children Do not use adhesivefor the locking screws lubricant agent oil andso on for the wall adapter Doing somay cause the material of the wall adapter to deteriorate and result in the projector falling and causing injury e Do not obstruct the projectors ventilation holes Doing so will prevent the dissipation of heat and may result in fire In particular do not use the projector in the following ways installing the projector in a place such as wall and so on where ventilation is poor covering it etc gt 00009 o Do not install the projector in front of the outlets of an air conditioner or heater orin a place exposed to significant vibrations Doing so may result in fires and electric shock Do not install the projector in humid or dusty places or those exposed to greasy smoke or steam such as near cooking equipment or humidifiers Doing so may result in fires e When installing the projector leave sufficient space between it and surrounding objects Failure to do so will prevent the dissipation of heat and may result in fires OVO O Please e Avoid rooms with significant dust humidity greasy smoke or tobacco smoke Dirt will adhere to the optical parts such as mirrors which will cause i
6. e size of the projected image to the screen To do this grasp the projector firmly on both sides and move it carefully To adjust tilt in the left right direction proceed to step 3 If only size adjustment is to be performed tighten the two knobs shown in black in the illustration 10 3 Turn the left or right knob to adjust projector tilt in the left or right direction When the knob shown in black in the illustration is tightened the projector is rotated in the counterclockwise direction oa 1 4 When the adjustment is complete tighten the opposite knob that is still loosened 3 Adjust the horizontal tilt of the projector The projector adapter allows adjustment over a range of approximately 3 degrees Loosen the horizontal fixation nut double nut with a wench 2 Loosen the horizontal adjust screws left and right with the supplied hex wrench Loosen the two screws shown in black in the illustration 3 Make the adjustment by tightening the left or right screw until the top edge and bottom edge of the image are parallel 4 When the adjustment is complete tighten the opposite screw that is still loosened Tighten the horizontal fixation nut double nut with a wrench 11 4 Adjust the tilt Tilt adjustment is performed with the four adjustment knobs Front rear tilt adjustment Adjust together Left right tilt adjustment Fine adjustme
7. mage quality to deteriorate e Avoid places in which the screen is exposed to direct sunlight or illuminated light When surrounding light directly hits the screen the image appears washed out and is difficult to view e Avoid locations exposed to particularly high or low temperatures Doing so may result in breakdown For the ambient operating temperature see the users manual included with the projector Preparation m Packaged Parts Please check the packaged items LEC The package shall either contains arm for NPO2WK or NPO3WK Cover A B 2 pairs Arm NPO2WK 1 Arm NPO3WK 1 Arm cover 1 Plate B 1 Se w w v M420 screws 4 G amp M3 5x9 4 screws 2 Hex wrench 1 Wall plate 1 1 p 9G M5 screws 4 2 eta aa and Adjustment Manual 1 1 2 To be used when mounting the wall adapter in the North America region E Names of Parts Arm cover Elongate hole for screw or bolt 4 parts Covers A B Plate A ee Arm fixation screw Grooves for wiring Wall adapter B A Cover B A Central axis Projector Adapiar Plate B k Horizontal fixation nut 4 Horizontal adjust screws B2 Projector fixation J Vertical adjust Arm fixation knobs E Dimensions of Parts unit mm The dimensions of the positions of the wall fixation screws bolts of the wall adapter are described n _ L oO ek O O N The center of the wall adapter central axis 885 minimum
8. n it so as to ensure Be sure to observe the following precautions Use M6 1 4 inch for the wall fixation bolts and screws for the wall adapter Use an outlet for the power source of the projector Do not directly connect to the lamp line because this is dangerous Also use an accessible outlet so that you can connect and disconnect the power plug e Mounting on a wooden wall Ensure the load is mounted on a pillar or robust constructional material If the strength of the constructional material and so on is insufficient please reinforce it Do not mount on wall finishing material furring strip and so on e Mounting on a concrete wall Use a commercial anchor bolt M6 1 4 inch anchor nuts and similar which will bear the load of the projector e Do not install in places subject to constant vibration Extended vibration may cause loosening of the screws and result in the Wall Mount Unit and projector falling and causing injury Also it may cause breakdown of the projector To ensure safety be sureto tighten the bolts screws and adjusting knobs securely Failure to do so may result in the projector falling and causing injury Do not modify any parts Doing so may resultin the projector and the Wall Mount Unit falling and causing injury Do not use broken parts Doing so may result in the projector and the Wall Mount Unit falling and causing injury If a part should break consult your dealer Do not look into the mirror when th
9. nt in same direction as for vertical adjustment Adjust together Rotation axis e If tilt adjustment achieved with these knobs is not suf cient repeat the adjustment process from step 2 on page E 12 e During adjustment the position of the projected image may shift In such a case loosen the wall adapter and arm fixation screws and adjust the position This completes the adjustment Securely tighten all screws and adjustment knobs 12 5 Attach the covers to the projector adapter and the wall adapter q Attach cover A with hook and cover B with notch to the upper side of the wall adapter Slide the two coverstowards the center while pushing them down as shown in the illustration The bottom of each cover will then engage with the screw heads of the wall adapter At the same time the hook of cover A will enter the notch of cover B thereby locking the covers 2 On the bottom side of the wall adapter reverse the positions of covers A and B and attach them in the same way as described in Q 3 Attach the arm cover The cover is fixed when the left and right tabs engage with the notches on the projector adapter 2 Cover A should be at right Arm cover Cover B should be at left Specifcations Product name Wall mount unit Model NPO2WK NPO3WK Adjustment angle Up down angle 3 left right angle 3 inclination angle 10 Adjustment width Front rear 180 mm left righ
10. stortion the center of the wall adapter and the center of the screen should be aligned on a straight axis e The wall adapter has a top bottom orientation Be sure to attach it with correct orientation If the wall adapter is mounted with reversed top bottom orientation correct installation is not possible e The wall adapter can be adjusted horizontally over a range of 50mm O Use only M6 1 4 inch screws or bolts 4 locations to fix the wall adapter If screws or bolts other than M6 are used the projector may fall and cause injury 3 Attach the arm to the wall adapter Thread the cables through the arm plates and the arm 2 NPO2WK Loosen the arm fixation screws top and bottom with the supplied hex wrench NPO3WK Loosen the arm fixation screws 2 on top and 2 on bottom with the supplied hex wrench G Insert the arm plate A into the wall adapter from the top and tighten the screws top and bottom near the center of the elongated hole The covers A and B are to be attached after installation and adjustment are completed 4 Mount the projector assembled in step 1 on the arm To do this first remove the packing spacers from the projector Then hold the projector body with the help of a second person and insert it carefully into the arm Do not hold the projector by the cable cover or the mirror section and do not touch the mirror or lens Insert the central axis of the projector adapter into the arm
11. t 50 mm up down 50 mm NPO2WK External dimensions 280 W x 885 D x 219 H mm NPO2WK Weight Approx 7 5 kg TA NPO3SWK External dimensions 280 W x 1160 D x 219 H mm e NPO3WK Weight Approx 10 5 kg Sf eSpecifcations and design are subject to change without notice 3 S E 13
Download Pdf Manuals
Related Search