Losi 1/18 Mini-Rock Crawler RTR
Contents
1. LEDS will come on 2 Pull the throttle trigger all the way back full speed and press the setup button once only the GREEN LED will come on 3 Push the throttle trigger full forward brake reverse and push the setup button once only the RED LED will come on 4 Letthe throttle trigger return to the neutral center position and press the setup button once more to save the program and exit setup mode only the GREEN LED will be on Notes A If the receiver does not receive a signal from the Transmitter the ESC will not enter the Program mode B While in Program mode the motor will not run C Ifthe setup button is not pressed for 20 seconds while in the Program mode the ESC will exit the Program mode and the data will be saved Chassis Tuning The following are simple adjustments and easily maintained settings to assure proper operation and performance It is advised when making any adjustment that you do so in small increments and always check for other parts of the chassis that are affected Slipper Adjustments The Mini Rock Crawler is equipped with a slipper device offering both traction control and protection for the transmission The slipper is primarily used to help absorb sudden impacts on the drivetrain or when using more powerful aftermarket motors and or battery packs Additionally it can be used to smooth out the flow of power to the wheels Adjustment is made by turning the 3mm adjustment nut clockwise to the right to2. reduce the slip or counterclockwise to e e the left to increase the slip As you punch the throttle the slipper should slip no E more than an inch as it accelerates With the included motor and battery pack it Increase Slip Decrease Slip should slip just a little Make sure you replace the gear cover before running lt Steering Rate Your transmitter is equipped with a steering rate control to the left of the steering wheel This advanced feature usually found only on competition type radios allows you to adjust the amount the front tires move when you turn the steering wheel Full Rate Less Rate Steering Servo Saver Removal The Mini Rock Crawler steering servo comes with a servo saver installed As your rock crawling skills improve we have included a steering arm that eliminates the servo saver Although this setup provides more precise steering it does put your servo gears at risk for breakage Use caution when the steering servo is under severe loads 1 Center servo saver arm 2 Remove servo saver arm 3 With servo output shaft still assembly from the servo centered install solid servo Remove the steering ball stud arm with the shorter screw andinstall into solid servo arm supplied and attach steering linkage Page 4 Changing the Pinion Gear Gear Ratio Before you change the pinion gear ask yourself why you are doing it In general if you change to
3. you may need any assistance For guestions or assistance please direct your email to productsupport horizonhobby com or call 877 504 0233 toll free to speak to a service technician Inspection or Repairs If this Product needs to be inspected or repaired please call for a Return Merchandise Authorization RMA Pack the Product securely using a shipping carton Please note that original boxes may be included but are not designed to withstand the rigors of shipping without additional protection Ship via a carrier that provides tracking and insurance for lost or damaged parcels as Horizon is not responsible for merchandise until it arrives and is accepted at our facility A Service Repair Request is available at www horizonhobby com on the Support tab If you do not have internet access please include a letter with your complete name street address email address and phone number where you can be reached during business days your RMA number a list of the included items method of payment for any non warranty expenses and a brief summary of the problem Your original sales receipt must also be included for warranty consideration Be sure your name address and RMA number are clearly written on the outside of the shipping carton Warranty Inspection and Repairs To receive warranty service you must include your original sales receipt verifying the proof of purchase date Provided warranty conditions have been met your Product will be repair
4. MINI ROCK z CRAWLER gt 1 18TH SCALE READY TO RUN MINI ROCK CRAWLER Owner s Manual Thank you for choosing the Mini Rock Crawler from Losi This guide contains the basic instructions for operating your new Mini Rock Crawler While the Mini Rock Crawler is great for first time RC drivers it does reguire some mechanical experience and or parental supervision for drivers under 14 It is critical that you read all of the instructions in order to operate your model correctly and avoid unnecessary damage Please take a moment to look over all the printed materials before operating your new Mini Rock Crawler GO REGISTERYOUR PRODUCT ONLINE Losi a division of Horizon Hobby wants to ensure that you get maximum enjoyment from your 1 18 Mini Rock Crawler We strongly encourage you to register your product using the online Product Registration tool so we can notify you when there are updates tech tips new option parts or service bulletins available for your product Log onto WWW LOSI COM to complete the Product Registration form Not responsible for errors All prices subject to change without notice Losi a Division of Horizon Hobby Inc Safety Precautions This is a sophisticated radio controlled model that must be operated with caution and common sense Failure to operate your Mini Rock Crawler in a safe and responsible manner could result in damage to the model and property The Mini Rock Crawler is not intended for use by ch
5. T NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCT THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER S INTENDED USE c Purchaser Remedy Horizon s sole obligation hereunder shall be that Horizon will at its option i repair or ii replace any Product determined by Horizon to be defective In the event of a defect these are the Purchaser s exclusive remedies Horizon reserves the right to inspect any and all equipment involved in a warranty claim Repair or replacement decisions are at the sole discretion of Horizon This warranty does not cover cosmetic damage or damage due to acts of God accident misuse abuse negligence commercial use or modification of or to any part of the Product This warranty does not cover damage due to improper installation operation maintenance or attempted repair by anyone other than Horizon Return of any goods by Purchaser must be approved in writing by Horizon before shipment Damage Limits HORIZON SHALL NOT BE LIABLE FOR SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCT WHETHER SUCH CLAIM IS BASED IN CONTRACT WARRANTY NEGLIGENCE OR STRICT LIABILITY Further in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted As Horizon has no control over use se
6. T1 O CD w kr a 907LASO1 08y19SO1 907LASO1 O yLASOT 60yLASOT CCyLASOT cchLBSO1 LzpLdsO1 cc80dSO 1 LC Lr608SO1 d 9 7LASOT LepLasO1 SOyLASOT REO CY sn Z 4 yey19SO gt Ly608SO1 vev gso e sBulsnoy se xy Jeey pue JUOJJ JOJ sued ewes LE7LASOT LOSB1419 ee LOSB1447 Soft LOSB1419 LOSB1448 Firm LOSB1440 LOSB1441 LOSB1405 LOSB1442 I EE R d z LL LOSBO941 Z ij NAA E gt LOSB1430 To 2 LOSB1406 SY d f LOSB1413 LOSB1430 LOSB1405 PA Ca LOSB1430 LOSB1436 sO g LOSB1430 SA LOSB1460 LOSB1413 E e JO LOSB1460 Page 13 LOSB1490 LOSB1480 LOSB1498 Blue LOSB1499 Red Ole ts W A AU NN ei LZ NZ LE NPI RS LOS ZZ w d 4 RD LOSB1470 Page 14 Item LOSB0805 LOSB0806 LOSB0822 LOSB0823 LOSB0828 LOSB0839 LOSB0941 LOSB1048 LOSB1064 LOSB1068 LOSB1202 LOSB1376 LOSB1377 LOSB1378 LOSB1400 LOSB1401 LOSB1403 LOSB1405 LOSB1406 LOSB1407 LOSB1409 LOSB1410 LOSB1413 LOSB1414 LOSB1415 LOSB1417 LOSB1418 LOSB1419 LOSB1421 LOSB1422 LOSB1425 LOSB1426 REPLACEMENT PARTS Retail Losi DSM Transmitter Only EE 69 99 Losi DSM Receiver 5 MSX12 Digital Mini Servo MSX12 Digital Mini Servo Gear Set Mini Rock Crawler ESC Only 1 18 Mini Rock Cra
7. a larger pinion the wheel speed will increase but you will see less acceleration and run time This would only be advisable for low traction climbs Changing to a smaller pinion will give you guicker acceleration and possibly a bit longer run time but a little less wheel speed This would be good for high traction rock climbs The pinion on the Mini Rock Crawler offers the best balance of both To change the pinion remove the gear cover loosen the motor screws and slide the motor back Use the included 1 5mm allen wrench to loosen the pinion setscrew Place the new pinion on the end of the motor shaft and using the flat of the pliers or a similar flat tool push it on to the same position as the one removed See Setting the Gear Mesh below Your Mini Rock Crawler comes equipped with a 14 tooth pinion which provides an overall ratio of 86 1 If you increase the pinion size to a 15 tooth gear the ratio will change to 80 1 to decrease the pinion size to a 13 tooth will be 92 1 Warning When running aftermarket motors check with the motor manufacturer for correct gearing Never over gear the motor as it can cause overheating damaging it and the speed control Setting the Gear Mesh The motor screws should be slightly loose Slide the motor forward allowing the pinion gear to mesh with the spur gear Snug not tight the bottom motor screw and try rocking the spur back and forth There is a slight bit of movement before the motor is forced to turn over I
8. aged Check if plug in all the way Replace or repair servo Won t turn one direction Motor doesn t run Servo gears damaged Motor plugs loose Motor wire broken ESC damaged Replace servo gears Plug in completely Repair or replace as needed Call Electronics Tech ESC gets hot Motor over geared Driveline bound up Put smaller pinion on motor Check wheels amp trans for binds Poor run time and or sluggish acceleration NiMH pack not fully charged Charger not allowing full charge Slipper slipping too much Motor worn out Driveline bound up Recharge Try another charger Check adjust slipper Replace motor Check wheels amp trans for binds Poor range glitches Transmitter batteries low Transmitter antenna damaged Battery low in truck Loose plugs or wires Check amp replace as necessary Check amp tighten Replace or recharge Check motor and power plugs Slipper won t adjust Drive pin missing in shaft Spur gear face worn out Replace drive pin Replace spur gear amp adjust slipper Page 9 8LFLASO1T plLyLASO1 plLyLASO1 D SO S OZ E RZ 90808SO1 AD gt gzblasO1 a N 6LFLASO 1 CO0yLASOT 6LvL8SOT1 Page 10 LcpLAdSO 1 P90LASO 1 AD da Z ScvlLdsol 8cy19SOT 6cviaso1 ZetldSO1 S rLgSO1 SrLgSO1 Page 11 89019SO1 Cts o9rLgsol Q oy 097 8SO1 ze 6LvL8SO
9. ase call 877 504 0233 with any guestions or concerns regarding this product or warranty Instructions for Disposal of WEEE by Users in the European Union This product must not be disposed of with other waste Instead it is the user s responsibility to dispose of their waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or where you purchased the product LEO Page 8 TROUBLESHOOTING GUIDE Doesn t operate Battery not charged or plugged in Receiver switch not On Transmitter not On or low battery Charge battery plug in Turn on receiver switch Turn on replace batteries e Motor runs but wheels dont move Pinion not meshing with spur gear Pinion spinning on motor shaft Slipper too loose Transmission gears stripped Drive pin in axle missing Adjust pinion spur mesh Replace pinion gear on motor Check amp adjust slipper Replace transmission gears Check amp replace Steering doesn t work Servo plug not in receiver Servo gears or motor dam
10. ates on a radio signal you control it is important for you to read and understand about all of these functions and adjustments before driving The Receiver 1 Throttle Port Where the Electronic Speed Control ESC plugs in 2 Steering Port Where the steering servo s plugs in 3 Bind Port Used to bind the receiver to the transmitter 4 Indicator Light Shows that a frequency channel is being received The Electronic Speed Controller ESC 1 On Off Switch Powers the receiver and ESC 2 Setup Button and Indicator Light Used for resetting the ESC 3 Battery Lead Connects to the battery pack for power 4 Motor Lead Connects to the wire leads from the motor MSS MRX 3000 WITH AUX SPEKTRUM THROTTLE 2 4 GHz DSM STEERING CZ BIND ooo Page 2 The Transmitter 1 Steering Wheel Controls direction left right of the model 2 Throttle Trigger Controls speed and direction forward reverse of the model 3 Antenna Transmits signal to the model On Off Switch Turns the power on for the transmitter operation 5 Indicator Lights Green top light indicates adequate battery power Red bottom light indicates signal strength 6 Steering Trim ST TRIM Adjusts the hands off direction of the model 7 Throttle Trim TH TRIM Adjusts the motor speed to stop at neutral 8 Steering Rate Adjusts amount front wheels move when the steering wheel is turned l
11. can actually wash dirt into the bearings or moving parts as well as cause damage to the electronics Page5 Rebuilding Refilling the Shocks Step 1 After removing the shock push up on the lower spring cup and remove it from the shaft Remove the spring and preload spacers Step 2 Turn the shock upside down and remove the black shock cartridge shaft assembly from the shock body by turning it counterclockwise Note If you only wish to change or fill the shock fluid skip to step 5 Step 3 Remove the top E clip from the shock shaft Remove the shock piston Remove second E clip Step4 Reinstall the lower E clip Slide the shock piston onto the shock shaft against the E clip Reinstall Remove the old cartridge the top E clip Put a drop of oil on the shock shaft before installing a new shock cartridge Step 5 Step 6 If you plan on completely changing the shock fluid suggested dump out the old fluid from the shock body Carefully fill the shock body with fluid to the bottom of the threads inside the shock body Note Your Mini Rock Crawler S comes with 100wt shock fluid from the factory Pull the shaft out so the piston is next to the cartridge and reinstall the assembly into the shock body turn in a clockwise direction until snug DO NOT TIGHTEN yet Step 7 _ Turn the shock over and use a 0 Phillips screwdriver to remove the small bleed screw at the
12. ed or replaced free of charge Repair or replacement decisions are at the sole discretion of Horizon Hobby Non Warranty Repairs Should your repair not be covered by warranty the repair will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50 of the retail purchase cost By submitting the item for repair you are agreeing to payment of the repair without notification Repair estimates are available upon request You must include this request with your repair Non warranty repair estimates will be billed a minimum of hour of labor In addition you will be billed for return freight Please advise us of your preferred method of payment Horizon accepts money orders and cashiers checks as well as Visa MasterCard American Express and Discover cards If you choose to pay by credit card please include your credit card number and expiration date Any repair left unpaid or unclaimed after 90 days will be considered abandoned and will be disposed of accordingly Please note non warranty repair is only available on electronics and model engines Electronics and engines requiring inspection or repair should be shipped to the following address Horizon Service Center 4105 Fieldstone Road Champaign Illinois 61822 All other Products requiring warranty inspection or repair should be shipped to the following address Horizon Product Support 4105 Fieldstone Road Champaign Illinois 61822 Ple
13. eft or right 9 Steering Reverse Switch ST REV Reverses the function of the steering when the wheel is turned left or right 10 Throttle Reverse Switch TH REV Reverses the function of the speed control when pulled back or pushed forward 11 Bottom Cover Covers and holds the batteries powering the transmitter R Re Binding the Transmitter to the Receiver The Losi DSM radio system included in the Mini Rock Crawler operates on 2 4GHz and provides 79 different channels which are automatically selected when the transmitter and vehicle are turned on The communication between the transmitter and receiver starts in the few seconds after the transmitter and vehicle are both turned on This is called the binding process The Losi DSM radio system will not interfere with previous technology radio systems that operate on 27MHz or 75MHz frequencies and you will not receive any interference from them Although set at the factory below are the steps required to re bind your transmitter to the receiver should the need arise During the bind process there is a unique ID from the transmitter communicated to the receiver to ensure trouble free radio operation Steps to Re Bind the Receiver to the Transmitter 1 Ensure that the transmitter and vehicle are both turned off 2 Using the supplied Bind plug which looks like a standard receiver BIND PLUG plug with a wire loop installed insert the plug into the receiver sl
14. f Lockers Plastic Output Shaft Set Axles amp Center Diff 7 99 Top Shaft amp Idler Shaft 6 99 Assembled Shocks 2 Shock Rebuild Kit 2 Shocks Shafts 2 Shock Body 2 s 5 99 Ball Stud Long amp Shock Mounting Brace 6 99 Shock Spring Set Soft Shock Spring Set Firm 2 99 Assembled Universal Joints Slider shafts Slider Shafts Set plastic a 12mm Wheel Hex Set w hardware 1 11 6 99 Chrome Wheels 1 9 Mini Rock Claws Tires 2 1 9 Mini Rock Claws Glued 2 Chrome Wheels 22 99 Wheel Rings 8 Blue Wheel Rings 8 Red OPTION PARTS Mini Rock Crawler Clear Body w stickers 16 99 1 18th Grappler Body w Stickers amp Mask 18 99 Blue Anodized Chassis Plate Set Lazer etch 15 99 Red Anodized Chassis Plate Set Lazer erch 15 99 Aluminum 12mm Hex Set Black Chrome Wheels 2 1 3 Cell LiPo Charger Intelligent LiPo Balance Charger 1 5 Cells 139 99 7 4V 1650mAh 2 Cell LiPo 20C Slider 64 99 Losi A Division of Horizon Hobby Inc 4105 Fieldstone Champaign IL 61821 www Losi com 1 877 504 0233 Page 16 MRCV2 R5816T
15. f not pull the top of the motor back slightly and recheck If there is too much slop between the gears push the top of the motor forward When set properly the wheels can be spun forward freely with very little noise Make sure to tighten both motor screws and replace the gear cover before running Tuning Tips Weight Adding weight to the front wheels of the Mini Rock Crawler will help increase traction and lower the over center of gravity Using the LOSA99201 Self Stick weights carefully cut each piece in half and place inside the wheel as pictured It is important that the wheel weights be evenly placed inside the wheel to ensure that it is balanced Shock Oil and Springs The Mini Rock Crawler shocks are filled with Losi 30wt shock fluid By switching to thinner shock fluid the Mini Rock Crawler will have more traction guicker weight transfer and softer dampening Doing the opposite will cause the Mini Rock Crawler to react more slowly to input and have slower weight transfer Adjusting these settings will help adapt the Mini Rock Crawler to your conditions Please note the Mini Rock Crawler comes from the factory with a stiffer rear spring to help minimize Torque Flex often found in 4wd driver rock crawlers Cleaning Performance can be hindered if dirt gets in any of the moving suspension parts Use compressed air a soft paintbrush or toothbrush to remove dust or dirt Avoid using solvents or chemicals as they
16. hnology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2 400 GHz to 2 4835 GHz freguency range The following countries associated regulatory agencies recognizing the noted certifications for this product as authorized for sale and use are USA Belgium Canada Denmark Finland France Germany Italy Netherlands Spain Sweden UK Warning An RC model is not a toy If misused it can cause serious bodily harm and damage to property Operate only in open areas and follow all instructions included with your radio and model Warranty Information Warranty Period Horizon Hobby Inc Horizon warranties that the Products purchased the Product will be free from defects in materials and workmanship at the date of purchase by the Purchaser Limited Warranty a This warranty is limited to the original Purchaser Purchaser and is not transferable REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER This warranty covers only those Products purchased from an authorized Horizon dealer Third party transactions are not covered by this warranty Proof of purchase is required for warranty claims Further Horizon reserves the right to change or modify this warranty without notice and disclaims all other warranties express or implied b Limitations HORIZON MAKES NO WARRANTY OR REPRESENTATION EXPRESS OR IMPLIED ABOU
17. ildren without direct adult supervision Losi and Horizon Hobby shall not be liable for any loss or damages whether direct indirect special incidental or conseguential arising from the use misuse or abuse of this product or any product reguired to operate it e This model is controlled by a radio signal subject to interference from many sources outside your control This interference may cause momentary loss of control so it is advisable to always keep some distance in all directions around your model as a safety margin to avoid collisions Always operate your model in an open area away from cars traffic and people Avoid running your model in the street where damage can occur Never run your Mini Rock Crawler with low transmitter batteries Carefully follow the directions and warnings for this and any optional support eguipment Keep all chemicals small parts and anything electrical out of the reach of children Tools and Items You Will Find Handy Soft bristle brush for cleaning 5 5mm nut driver for the wheel nuts 0 or 1 Phillips screwdriver f 050 inch Allen Wrench LOSA99100 j 1 Note Use only Losi tools or other high guality tools Use of inexpensive tools can cause damage to the small screws and parts used on this type of model The Radio System The following is an overview of the various functions and adjustments found on the Mini Rock Crawler radio system Since the Mini Rock Crawler oper
18. ot labeled BIND Looking down on the receiver this slot would be below the LED and is the furthest from the LED or nearest to the corner of the receiver Note You do not need to remove any of the other plugs to re bind 3 With the Bind plug installed turn on the vehicle Notice a blinking orange LED within the receiver 4 Nowyouare ready to turn on the transmitter You should notice on the back of the transmitter a similar blinking orange LED under the translucent cover MaS 5 Both the receiver and transmitter orange LED will stop blinking X 3000 and become solid indicating they have bound themselves SU together T 6 Please turn off both the vehicle and transmitter to remove the Bind plug from the receiver Failing to remove the Bind plug will cause the transmitter to attempt to rebind every time you turn on the vehicle and transmitter 7 Turn on both the vehicle and transmitter to ensure operation If the transmitter does not control the vehicle please repeat steps 1 to 6 Should this not correct the problem please call Horizon Service Repair for further assistance 8 The Bind process is complete Your vehicle s radio system should be ready for use Page 3 Resetting the ESC The ESC comes from the factory preset and ready for use If for some reason you should need to reset the ESC use the following instructions 1 Turn on the transmitter and ESC Press the setup button both the RED and GREEN
19. top of the shock Slowly push the shock shaft up until it stops Excess fluid should flow out of the bleed hole Slowly pull the shock shaft halfway back and replace the bleed screw Use pliers to tighten the cartridge being careful not to strip the plastic lobes on the cartridge Step8 Replace the spring and spring cup and test the shock action for smoothness and leaks Retighten the bleed screw or cartridge if either leaks Remount the shock on your truck Service Repair Radio Speed Control and Motor If you have any problems other than those covered in the troubleshooting section please call the electronics service department at 877 504 0233 They will be able to give your specific problem additional attention and instruct you as to what needs to be done Chassis If you have any questions other than those covered in the troubleshooting or maintenance sections please call 877 504 0233 Page 6 LOSI DSM Radio System This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device rnust accept any interference received including interference that may cause undesired operation Caution Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the eguipment This product contains a radio transmitter with wireless tec
20. tup final assembly modification or misuse no liability shall be assumed nor accepted for any resulting damage or injury By the act of use setup or assembly the user accepts all resulting liability If you as the Purchaser or user are not prepared to accept the liability associated with the use of this Product you are advised to return this Product immediately in new and unused condition to the place of purchase Law These Terms are governed by Illinois law without regard to conflict of law principals Safety Precautions This is a sophisticated hobby Product and not a toy It must be operated with caution and common sense and requires some basic mechanical ability Failure to operate this Product in a safe and responsible manner could result in injury or damage to the Product or other property This Product is not intended for use by children without direct adult supervision The Product manual contains instructions for safety operation and maintenance It is essential to read and follow all the instructions and warnings in the manual prior to assembly setup or use in order to operate correctly and avoid damage or injury Page 7 Ouestions Assistance and Repairs Your local hobby store and or place of purchase cannot provide warranty support or repair Once assembly setup or use of the Product has been started you must contact Horizon directly This will enable Horizon to better answer your guestions and service you in the event that
21. wler Motor Fr R Metal Diff Gear amp Housing set Body Clips 10 Slipper Hardware Set Spur Gear Bag 7 2v 1100mAh Ni MH Battery Mini Rock Crawler Body Blue Mini Rock Crawler Body Red Mini Rock Crawler Body Black Aluminum Chassis Plate Set Motor Plate Body Post Set Axle Housing 2 w hardware Axle Shafts 2 Axles 2 Front Spindles amp Carriers w hardware Steering Links Long amp Short Rear Hub Set w hardware 3 Link Connector w pivot ball Radio Plate Battery Mounts amp Strap Lower Suspension Rods Lower Suspension Rod Ends w pivot ball Complete Screw Kit Servo Plates amp Mounts Servo Saver amp Arm Set Center Transmission Case Set Transmission Skid Plate Description Item LOSB1427 LOSB1428 LOSB1429 LOSB1430 LOSB1431 LOSB1434 LOSB1436 LOSB1437 LOSB1440 LOSB1441 LOSB1442 LOSB1443 LOSB1444 LOSB1447 LOSB1448 LOSB1453 LOSB1454 LOSB1460 LOSB1470 LOSB1480 LOSB1490 LOSB1498 LOSB1499 LOSB1320 LOSB1321 LOSB1400B LOSB1400R LOSB1461 LOSB1471 LOSB9603 LOSB9605 LOSB9833 Page 15 Description Retail Center Transmission Gear Cover 5 99 Center Transmission Gear Set 5 99 Center Transmission Bearing Set Bearing 4x8x3mm Axle Bearing Bearing 7x11x3 Diff Bearing Center amp Dif
Download Pdf Manuals
Related Search