Home

Cambridge Azur 840A

image

Contents

1. This completely removes them from the signal path for maximum fidelity If the musical recording is of poor quality or other factors are affecting the sound quality if desired you can adjust the tone controls to compensate To use the tone controls press the Direct button so that the Bass Treble icon 2 6 lights in the display indicating that they are active and direct mode is Off Now press the Bass or Treble controls themselves to release them and allow adjustment push them back in when finished Bass Treble Direct O o OOO o The 840A V2 stores whether direct mode is on or off for each input individually for example it is possible to have the tone controls automatically active for the Tuner source but not the CD source 10 Amplifier setup The 840A V2 features many advanced settings that allow it s use to be customised to user preference The inputs can be named to reflect the actual source units you have each input can be trimmed so that each sounds the same in terms of loudness when you switch between them and other options Changing input names source naming o CANCEL 6 2 2 Press and hold the relevant input select button for four seconds to change its name For example if Input 1 is a CD player name it CD etc Letters are selected by turning the volume control to scroll through the available characters Press LEFT or RIGHT to select which character you wish
2. Check speaker connections Check interconnects There is a loud buzz or hum Check turntable or tone arm for ground and connection lead fault Ensure no interconnects are loose or defective Ensure that your tape deck turntable is not too close to the amplifier Unable to make or play tape recordings Check that TAPE MON and TAPE OUT have been connected correctly There is weak bass or diffused stereo imaging Ensure that speakers are not wired out of phase Message on display flashing See section on CAP5 protection system The remote handset will not function Check that the batteries have not expired Ensure that nothing is blocking the remote sensor For more frequently asked questions FAQ s technical advice and information on getting the most out of your 840A V2 please visit the Support section on Cambridge Audio s website www cambridgeaudio com support php For all servicing in or out of warranty please contact your dealer azur 840A V2 Technical specifications Power Output THD unweighted Frequency Response S N ratio ref 1W 8 Ohm Input impedances Power Amp damping factor Max power consumption Minimum power consumption Bass amp Treble controls Dimensions H x W x D Weight 120W RMS into 8 Ohms 200W RMS into 4 Ohms lt 0 001 1 kHz at 80 of rated power ENGLISH lt 0 01 20 Hz 20 kHz at 80 of rated power 10 Hz 50 kHz 1 dB gt 93 dB Input 1
3. jp YA i Class XD integrated amplifier ao User s ji 3 azur 840A V2 Cambridge Audio Your music our passion Cambridge Audio Important safety instructions For your own safety please read the following important safety instructions carefully before attempting to connect this unit to the mains power supply They will also enable you to get the best performance and prolong the life of the unit Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with a dry cloth s OORA WN KF Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories speci
4. O Au LI Ja INPUT 4 waye Description CAP5 has the ability to detect when the amplifier starts to clip or overdrive at its output which can damage loudspeakers and degrade the sound Clipping distortion is caused at high volume levels when the output signal attempts to go outside the maximum voltage that the Clipping amplifier can provide causing the tops of the signal to flatten off When CAP5 detects clipping the volume will be automatically reduced down until CAP5 detects an undistorted output It is possible to disable the clipping detection feature by pressing the CLIP DT button to off when in the 840A V2 System Configure menu Note Disabling the clipping detection is not advised as this feature has been added deliberately to protect the amplifier and loudspeakers Troubleshooting There is no power Ensure the AC power cord is connected securely Ensure the plug is fully inserted into the wall socket and is switched on Check fuse in the mains plug or adaptor There is no sound Make sure the unit is not in Standby mode Check that source component is properly connected Check that TAPE MON is not switched on unless tape input is required Check that your speakers are properly connected If using Speaker B terminals check they are switched on Make sure unit is not in mute mode There is no sound on one channel Ensure that balance control is in the correct position
5. PURPOSE Some countries and US states do not allow the exclusion or limitation of incidental or consequential damages or implied warranties so the above exclusions may not apply to you This Warranty gives you specific legal rights and you may have other statutory rights which vary from state to state or country to country For any service in or out of warranty please contact your dealer Plug Fitting Instructions UK Only The cord supplied with this appliance is factory fitted with a UK mains plug fitted with a 5 amp fuse inside If it is necessary to change the fuse it is important that a 5 amp one is used If the plug needs to be changed because it is not suitable for your socket or becomes damaged it should be cut off and an appropriate plug fitted following the wiring instructions below The plug must then be disposed of safely as insertion into a mains socket is likely to cause an electrical hazard Should it be necessary to fit a 3 pin BS mains plug to the power cord the wires should be fitted as shown in this diagram The colours of the wires in the mains ead of this appliance may not correspond with the coloured markings identifying the terminals in your plug Connect them as follows The wire which is coloured BLUE must be GREEN E connected to the terminal which is marked YELLOW with the letter N or coloured BLACK FUSE The wire which is coloured BROWN must be BLUE connected to the terminal wh
6. instructions and Amplifier setup section of this manual for more information Q Bass and Treble Press to release and rotate to allow subtle adjustments to the tonal balance of the sound G9 Direct This control gives the audio signal a more direct path to the power amplifier stage of your amplifier bypassing the tone control circuits for the purest possible sound quality The Bass Treble icon 2 6 appears in the display when the bass and treble circuit is active in circuit and is not present when they are bypassed Note Direct can be set on or off individually for each input This settting is recalled each time a source is selected ay Volume Use to increase decrease the level of the sound from the outputs of the amplifier This control affects the level of the loudspeaker output the pre amp output and the headphone output It does not affect the Tape Out connections As the 840A V2 uses a very high quality passive resistor ladder switched by relays to achieve volume and balance audible control clicks can be heard from the unit when the volume or balance is adjusted The Volume control is also used in navigating the 840A V2 System Configure menus on the front panel display Please refer to the Operating instructions section of this manual for more information on some functions of these buttons Remote control The 840A V2 is supplied with an Azur Navigator remote control that operates both this am
7. NXE Order of selection 1 Input 1 2 Input 2 3 Input 3 4 Input 4 5 Input 5 6 Input 6 Tape 12 Connections to the 840A V2 s Incognito Ready A BUS Ready outputs are made by Cat 5 cable terminated with an RJ45 jack plug The RJ45 plug must be wired to the EIA TIA 568A wiring standard Wire colours 3 Orange White 6 Orange 1 Green White 4 Blue 7 Brown White 2 Green 5 Blue White 8 Brown ja AL Tot lt tod I IJI 87654321 12345678 LJ Plug view from View into contact end socket Gather pairs trim and insert into RJ45 plug Crimp wires securely in place To allow control of your source equipment from the remote rooms an IR emitter IR10 is plugged into one of the IR outputs on the rear of the unit and then attached over the IR window of the source unit Alternatively on our own products that feature IR emitter Inputs a mini jack to mini jack lead can be used Commands received by the keypads can now be sent back to the source equipment via the 840A V2 It is then possible to control the source equipment from the remote rooms by using the source equipment s own remote controls or through a learning remote The Incognito LR10 Learning Remote can fully control the keypads learn the source s remote control codes including those from other manufacturers and change source input on the 840A V2 etc On the
8. a stereo power amplifier for that selected input only For example as well as operating as a pure stereo amplifier the 840A V2 can provide the amplification for the front left and right channels of a surround sound setup with an AV receiver providing amplification for the other channels and controlling the overall system volume When listening in stereo use the 840A V2 and connected stereo sources as normal for best possible sound quality For surround sound select the fixed level input you have chosen on the 840A V2 and now use the AV receiver to control the volume select connected surround sound sources etc You may wish to re name the fixed level input as A V mode or similar on the 840A V2 Make connections as below the left and right preamp outputs of the AV receiver connect to the fixed gain input chosen on the 840A V2 As the gain can be fixed to any value it is easy to match the level of the 840A V2 to that of the other AV channels Stereo ___ J sources Surround sound _ _ sources SR AV receiver 0 O SB Oo azur To set a fixed volume for a source select FIXED INP in the System Configure menu 8 Oe lt OOOO Volume Select the input required and set the fixed gain using the volume control the OFF setting does not disable the input but leaves the input gain subject to the volume control
9. batteries according to local environmental electronic waste disposal guidelines Loudspeakers Before making any connections to loudspeakers make sure all power is turned off and only use suitable interconnects Servicing These units are not user serviceable never attempt to repair disassemble or reconstruct the unit if there seems to be a problem A serious electric shock could result if this precautionary measure is ignored In the event of a problem or failure please contact your dealer azur Limited warranty Cambridge Audio warrants this product to be free from defects in materials and workmanship subject to the terms set forth below Cambridge Audio will repair or replace at Cambridge Audio s option this product or any defective parts in this product Warranty periods may vary from country to country If in doubt consult your dealer and ensure that you retain proof of purchase To obtain warranty service please contact the Cambridge Audio authorised dealer from which you purchased this product If your dealer is not equipped to perform the repair of your Cambridge Audio product it can be returned by your dealer to Cambridge Audio or an authorised Cambridge Audio service agent You will need to ship this product in either its original packaging or packaging affording an equal degree of protection Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that this product is within the warra
10. check the speaker connections and ratings 14 4 Short circuit detection Indication Unit has not come out of Standby display flashes SPKR SHORT Press the INFO input select button for a brief on screen description and remedy or read below for more information Mode INFO RESET O 6 gt ane Description During power up from Standby CAP5 performs a check on the loudspeaker terminals to see if a short across the terminals has been accidentally introduced display flashes SPKR CHECK If the resistance measured across the loudspeaker terminals is too low the unit will stay in Standby mode until the fault has been removed and Power up is re attempted display flashes SPKR SHORT Remedy User related fault There may be a short circuit between the loudspeaker terminals Press the RESET input select button and check all loudspeaker connections before attempting to switch the unit out of Standby display will flash SPKR CHECK then SPKR OK when short circuit fixed It is possible to disable the short circuit detection feature by pressing the SHORT DT button to off when in the 840A V2 System Configure menu but it is not recommended This would only be required if the loudspeakers have very low DC resistance 5 Intelligent clipping detection Indication Volume is reduced automatically CLIPPING appears on the front panel display aie witli KE
11. due to possible interference Electronic audio components have a running in period of around a week if used several hours per day This will allow the new components to settle down the sonic properties will improve over this time Power sources The unit should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company This unit has been designed to be left in Standby mode when not in use this will increase the life of the amplifier this is true with all electronic equipment To turn the unit off completely switch off on the rear panel If you do not intend to use this unit for a long period of time unplug it from the mains socket Overloading Do not overload wall outlets or extension cord as this can result in a risk of fire or electric shock Overloaded AC outlets extension cords frayed power cords damaged or cracked wire insulation and broken plugs are dangerous They may result in a shock or fire hazard Be sure to insert each power cord securely To prevent hum and noise do not bundle the interconnect leads with the power cord or speaker leads Cleaning To clean the unit wipe its case with a dry lint free cloth Do not use any cleaning fluids containing alcohol ammonia or abrasives Do not spray an aerosol at or near the unit Battery disposal Please dispose of any discharged
12. navigate and control simply by using the input select buttons to turn a feature on solid circle or off no circle and the volume control knob to increase decrease settings Volume wa O EN P Adjust the volume control knob on the front panel or using the remote control The display will show the change in volume in decibels dB OdB indicates maximum volume while lower volume settings progress into the negative range This can also be changed to volume units 0 96 in the System Configure menu Speaker A B Speaker A B e 8 fom INPUT 4 za UT UT Volume Press the Speaker A B button to scroll through the speaker sets connected via the rear panel speakers A B or A and B Balance e Se Press the Mode button to enter Balance mode BALANCE will appear on the display and can be adjusted using the volume control Press the Mode button again to return to Volume mode or wait 5 seconds for the 840A V2 to automatically exit Balance mode Volume Bass and Treble These controls allow subtle adjustments to the tonal balance of the sound Modify the sound through your loudspeakers and the Pre Out sockets only they do not affect the signals sent through the Tape Out connections With a well produced CD and a good system the tone controls are unnecessary and can be switched out by pressing the Direct button ee ae o OO
13. non Cambridge Audio sources with balanced outputs ENGLISH Note The Input 1 switch must be in the Balanced position Balanced Balanced connections in an audio system are designed to reject electrical noise from power wiring etc and also the effects of noise currents flowing through ground connections The basic principle of balanced interconnection is to get the signal you want by subtraction using a three wire connection One signal wire the hot or in phase carries the normal signal while other the cold or phase inverted carries an inverted version The balanced input senses the difference between the two lines to give the wanted signal Any noise voltages that appear identically on both lines these are called common mode signals are cancelled by the subtraction An additional advantage is that the connection effectively carries twice the signal level and so improves the signal to noise ratio The 840A V2 and 840C are designed to work at their highest performance when a balanced interconnect is used Cambridge Audio Operating instructions The 840A V2 has a custom made display on the front of the unit showing the current status and allowing you to access the 840A V2 System Configure menus Here you can adjust the listening settings of the amplifier to personal preference The menu system is easy to
14. which is the default setting When a source has a fixed input the balance is always set to neutral Press the Mode button to exit On Off control menu When going in out of Standby mode the 840A V2 can automatically turn on and off other connected Cambridge Audio Azur models that have control bus sockets For this feature to work the units must be connected together see diagram by RCA phono leads The sockets are colour coded orange on the rear panels of compatible Azur models Loop out from the 840A V2 Control Bus Out to the Control Bus In on another Azur model e g 840C Continue the chain to other Azur models if required 640T V2 0 Cambridge Audio 840A V2 Now while the 840A V2 is on press and hold the Standby On button until ON OFF CTR appears on the display 20 Volume Standby On Select the connected Azur models by pressing the appropriate input select button For example CA XXXC for an Azur CD player 540C V2 640C V2 CA XXXD for an Azur DVD player CA DAB T for an Azur DAB tuner etc Press ON amp OFF to scroll through the options of ON turns all Azur units on only OFF turns all Azur units into Standby only or ON amp OFF turns all Azur units on and into Standby mode Press OK to confirm and exit 11 840A V2 ENGLISH Cam
15. balanced 20 kOhm Inputs 2 7 20 kOhm Tape Input 20 kOhm gt 110 at 1 kHz 800W Active no signal 7OW Standby 7W Shelving type Max bass boost cut 10 dB at 10 Hz Max treble boost cut 7 5 dB at 20 kHz 115 x 430 x 385mm 4 5 x 16 9 x 15 2 15 0kg 33Lbs 15 Cambridge Audio is a brand of Audio Partnership Plc Registered Office Gallery Court Hankey Place London SE1 4BB United Kingdom Registered in England No 2953313 www cambridge audio com as 2008 Cambridge Audio Ltd D D X a z
16. bridge Audio Multi room connections The 840A V2 features Incognito Ready A eae BUS Ready outputs allowing multi room capability One or two amplified keypads Pau i can be plugged into the 840A V2 using CAT 5 5e cable and RJ45 plugs to provide multi room audio in one or two secondary rooms or zones The keypads are powered by an external PSU also required through the CAT 5 5e cables and no mains connection is required in the secondary rooms Keypad 2 R2 R4 Speakers e g SS10 connected via speaker cable AS10 Passive Speaker O KP10 EU keypad AS10 Active Speaker wd ee p z Ce amp The 840A V2 is Incognito Ready Type II which means the keypads can operate independently of the amplifier in terms of volume bass treble etc be independently turned on and off and can also listen to a different source from that which is currently selected on the amplifier However both keypads can only listen to the same source A BUS is a standard that allows compatibility between different manufacturers equipment so A BUS compatible keypads from other manufacturers can also be used If used with our own Incognito KP10 keypads there are some extra features such as the ability to change source on the 840A V2 from the keypad EU model shown here ZRN DEL
17. cation Unit has switched off during operation display flashes DC ERROR Press the INFO input select button for a brief on screen description and remedy or read below for more information a Ka O o D Description CAP5 offers loudspeaker protection if the output of the amplifier goes to a high constant voltage DC because of some internal fault This is a rare fault although detecting it could just save those expensive loudspeakers Remedy Due to the necessary sensitivity of the DC protection circuit extremely hard clipping of the amplifier may cause DC protection to be triggered If this fault occurs press the RESET input select button then press the Standby On button to power up again and check operation with a reduced volume level If the DC fault occurs again please contact your dealer for service 2 Over temperature detection Indication Unit has switched off during operation display flashes ren tro resete O 6 r F 0 OVER TEMP Press the INFO input select button for a brief on screen description and remedy or read below for more information Description Over temperature is caused by a combination of high listening levels and low impedance speakers CAP5 includes temperature detection which constantly monitors the heat generated by the output transistors If the monitored temperature reaches a high level Suitably within the limits of th
18. e output devices the amplifier will automatically switch into a fault mode The unit should ideally be left for 15 minutes in this state to cool down adequately If the unit has not fully cooled down then the temperature may reach the limit soon after the amplifier is powered up If the loudspeaker impedance is low the temperature of the amplifier may rise faster as the amplifier is working harder If the amplifier is mounted in a cabinet or the ventilation slots are obstructed the over temperature detection may activate reactivate after a short listening time Remedy User related fault The internal temperature of the output transistors has reached the over temperature limit Press the RESET input select button and leave the unit for 15 minutes to cool down before pressing the Standby button to resume normal operation 3 Overvoltage overcurrent detection Description CAP5 offers V I voltage current protection by constantly monitoring the output transistors to keep them working inside their Safe Operating Area SOA The SOA is a set of limits given by the output transistor manufacturer to ensure reliability The V I protection has been incorporated within the amplifier circuitry to provide a fast response to temporary overload conditions When the V I protection is triggered the unit will continue to operate but distortion may be heard as the unit protects the output transistors Remedy Reduce the volume If distortion is still present
19. e the original and recorded signal so that adjustments to the recording parameters of the tape machine can be made consult the manual of your 3 head analog cassette deck for full details KE Preamp Out Connect these sockets to the inputs on an external power amplifier s or active subwoofers etc 840A V2 ENGLISH Cambridge Audio Front panel controls Cambridge Audio azur 840A Class XD Integrated Amplifier Standby On Phones Speaker A B Mode Treble Direct C OOO OO 0060 4 Standby On Switches the unit between Standby mode indicated by dim power LED and On indicated by bright power LED Standby is a low power mode where the power consumption is less than 10 Watts The unit should be left in Standby mode when not in use Note As default the 840A V2 ramps the volume up or down when switched on and when going into Standby mode This feature can be turned off if desired please refer to the Amplifier setup section of this manual for more information 2 Phones Allows for the connection of stereo headphones with a Ya Jack plug Headphones with an impedance of between 32 and 600 ohms are recommended When the headphones are connected the loudspeaker relays are released switching off the output to the loudspeakers speakers A and B 3 Speaker A B Press to scroll through the speaker sets connected to the loudspeaker terminals on the back panel spea
20. eature direct IR Control codes as well as toggle codes for some of their features to simplify programming custom installation systems Special direct On Off and Mute commands can be accessed on the supplied remote control for teaching into C I systems as follows 1 Press and hold the Standby On button The remote first generates it s standby toggle command Keep the button held down after 12 seconds an amplifier On command will be generated If the button is kept held down for a further 12 seconds an amplifier player Off command is generated 2 Press and hold the Mute button The remote first generates it s mute toggle command Keep the button held down after 12 seconds a Mute on command will be generated If the button is kept held down for a further 12 seconds a Mute off command is generated A full code table and RS232 protocol for this product is available on the Cambridge Audio website www cambridge audio com azur 840A V2 13 ENGLISH Cambridge Audio CAP5 Fiveway protection system Cambridge Audio has developed a proprietary protection system to ensure reliability and a long life for its amplifiers and the speakers they are connected to Note Due to the required sensitivity of the CAP5 system it is possible that mains power disturbances can falsely trigger CAP5 in extreme situations This protection system comprises of five main protection methods 1 DC detection Indi
21. elow shows how to connect the amplifier to a tape recorder or other source with a record and monitor connection 840A V2 Cambridge Audio Please note that either of the tape loop outputs can be used as they are both the same signal in parallel Speaker B connections The Speaker B connections on the back of the amplifier allow for a second set of speakers to be used i e speakers located in another room The Speaker A B button on the front panel allows this second set of speakers to be switched on and off Note When using two pairs of speakers use speakers with a nominal impedance of between 6 8 ohms each minimum Preamp Out connections The Preamp Out sockets are for connecting to the input sockets of a power amplifier or active subwoofer The diagram below shows how to connect the amplifier to an active subwoofer via the Line In inputs on the subwoofer azur 840A V2 Balanced audio connections The diagram below shows how to connect the 840A V2 to the Azur 840C Upsampling CD player using the Balanced Audio inputs via three pin XLR connectors The 840A V2 can also be connected to
22. els By actively displacing the crossover point this technology creates a region of pure Class A operation where the crossover zone would otherwise be before moving into an enhanced form of Class B at higher levels It should not be confused with Class AB which gives a small area of Class A but at the cost of higher distortion as soon as the signal level moves outside the AB area Class XD circuitry not only removes crossover distortion from the zero crossing point but also reduces distortion in the other parts of the amplifier s output range This V2 version of the 840A features our latest development of Class XD with many tweaks and enhancements from our on going research resulting in our best sounding implementation to date A white paper on this patent pending technology is available on our website www cambridge audio com Please note that because of the Class XD technology the 840A V2 runs slightly warmer than a conventional Class B AB amplifier and the ventilation slots on the top of the unit must not be obstructed Other features include the use of precision resistor ladders switched by gold plated relay contacts for the volume and balance controls rather than the more common solid state or volume potentiometer schemes Volume is controllable in 1 dB steps over most of the range giving very fine control an accurate logarithmic law and superbly accurate channel balance Input switching is also by high quality gold contact relays T
23. fied by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as the power supply cord or plug being damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped WARNING To reduce the risk of fire or electric shock do not expose this unit to rain or moisture The unit is of Class 1 construction and must be connected to a mains socket outlet with a protective earthing connection The unit must be installed in a manner that makes disconnection of the mains plug from the mains socket outlet or appliance connector from the rear of the unit possible Where the mains plug is used as the disconnect device the disconnect device shall remain readily operable Only use the mains cord supplied with this unit Please ensure there is ample ventilation at least 10cm clearance all round Do not put any objects on top of this unit Do not situate it on a rug or other soft surface and do not obstruct any air inlets or outlet gr
24. front panel display of the 840A V2 the extra multi room zones are indicated by a circle outline next to the input source see Fig 1 When listening to the same source the circle outline and solid circle overlap see Fig 2 Fig 1 One or both keypads are listening to a different source Input 2 to the amplifier Input 1 a O o o Fig 2 One or both keypads are listening to the same source Input 2 as the amplifier Input 2 Mode 0000 0000 Volume For further details on the Incognito multi room system please contact your local Cambridge Audio dealer or visit www cambridge audio com Custom installation C I use The 840A V2 features a Control Bus input output REmitter Control Bus that allow un modulated remote control commands S Dai positive logic TTL level to be received electrically by the unit and looped to another unit if desired e These control commands are typically generated by custom installation multi room systems or remote IR receiver systems The Control Bus sockets are colour coded orange An IR Emitter Input is also provided that allows modulated IR remote control commands to be received electrically by the unit Commands on this input operate the unit only and are not looped out demodulated on the Control Bus Output REG An RS232C port is also featured which allows the 840A V2 Be to be controlled by C I systems In addition the units f
25. functions of these buttons azur iPod compatibility To make use of the iPod functionality your iPod dock must be connected to Input 4 The 840A V2 remote can also control the basic functions of Apple iPod models when mounted in Cambridge Audio s iPod docks Apple s Universal Dock or other docks compatible with the Apple Remote Refer to your dock s instruction manual on how to connect it to your amplifier To use the Azur remote to control the docked iPod hold down the Input 4 button whilst pressing one of the following buttons EP Play Pause Press to play the iPod press again to pause play WE Skip Press once to skip forwards or backwards one track 840A V2 ENGLISH Cambridge Audio Connections When designing our amplifiers we have tried to include features that allow you to connect your system in various ways The inclusion of features such as Pre Out and Speaker B connections mean that you can flexibly configure your system depending on your requirements Basic connections The diagram below shows the basic connection of your amplifier to a CD player and a pair of loudspeakers Note If using Input 1 Unbalanced the Input 1 switch must be in the Unbalanced position Balanced Unbalanced i L Cambridge Audio Cambridge Audio Tape connections The diagram b
26. he 840A V2 features separate transformer secondaries for left and right channels twin rectifiers and separate PSU s for dual mono operation of the left and right power amplifiers A separate transformer supplies the preamp making the 840A V2 effectively a Pre and Power amp combination in one box Input 1 features a balanced input using XLRs giving optimal performance with equipment such as the matching 840C Upsampling CD player which features balanced outputs The casework combines massive structural rigidity with careful damping and control of acoustic resonance An Azur Navigator remote control is also provided giving full remote control of your amplifier in an attractive and easy to use handset We have also included support for multi room use By plugging in one or two external Cambridge Audio Incognito keypads and a power supply unit your amplifier can become the hub of a simple multi room system In addition Control Bus Input Output IR Emitter Input and RS232 control are featured making it easy to integrate the 840A V2 into a Custom Installation system if desired Your amplifier can only be as good as the system it is connected to Please do not compromise on your source equipment speakers or cabling Naturally we particularly recommend models from the Cambridge Audio Azur range These have been designed to the same exacting standards as this amplifier Your dealer can also supply excellent quality Cambridge Audio interconnects to ens
27. hen used and installed according to this instruction manual For continued compliance only Cambridge Audio accessories should be used with this product and servicing must be referred to qualified service personnel C Tick mark This product meets the Australian Communications Authority s Radio communications and EMC requirements A Ross Test Stamp This product meets Russian electronic safety approvals FCC regulations NOTE THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY TO OPERATE THE EQUIPMENT This equipment has been tested and found to comply with the FC limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receivi
28. ich is marked N with the letter L or coloured RED The wire which is coloured GREEN YELLOW x must be connected to the terminal which is CORD marked with the letter E or coloured GREEN GRIP f a standard 13 amp BS 1363 plug is used a 5 amp fuse must be fitted or if any other type of plug is used a 5 amp fuse must be fitted either in the plug or adaptor or on the distribution board 840A V2 ENGLISH Cambridge Audio Contents Important Safety INSErUCHIONS w wwmmamana nanma nanunua nana nanu manaa na kazaa 2 LIPA warnanya iao a a EE 3 oTM E E A AA AA AA 4 UA E A 4 Rear panel CONNECUONS aaa 5 Front panel AI cecieiesescestesteseavedscevteedasediesesd co sdverriedeerereriraie 6 REMOTE CONTO ai 7 iPod compatibil se siiesicciiscdactcacndasscosteoeccaegacadecas chavecoascesicscacseancban 7 CHANGE ONE 8 Operating INSWUCTIONS aa 10 Amplifier SetUp II 10 Mullti ROOM CONNECTIONS aa sanaan a ea 12 CUSTOM installation USE ccccccscccnsnsasnnrstcacacasactsasietsisnepsoasessseiarsanaees 13 CAPS protection Syste ii E EE EEEa 14 TOUbIESHOOUNG ii 15 Technical SpECifiCatiONnS aa 15 Oe ee ee ee ee eS a ene mla adi a Make sure you register your purchase Visit www cambridgeaudio com sts By registering you ll be the first to know about eo Future product releases Software upgrades News events and exclusive offers plus competitions This guide is designed to make installing and
29. illes Do not cover the ventilation grilles with items such as newspapers table cloths curtains etc This unit must not be used near water or exposed to dripping or splashing water or other liquids No objects filled with liquid such as vases shall be placed on the unit Risk of electric Risque de choc Vorm ffnen shock electrique des ger tes Ne pas ouvrir Netzstecker ziehen Do not open The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the service literature relevant to this appliance WEEE symbol The crossed out wheeled bin is the European Union symbol for indicating separate collection for electrical and electronic equipment This product contains electrical and electronic equipment which should be reused recycled or recovered and EE Should not be disposed of with unsorted regular waste Please return the unit or contact the authorised dealer from whom you purchased this product for more information CE mark This product complies with European Low Voltage C 2006 95 EC and Electromagnetic Compatibility 89 336 EEC Directives w
30. ker sets A B or A and B This can be used for listening to an extra set of loudspeakers in another room Please note that care should be taken when choosing speakers if two loudspeakers are going to be used on each channel If the combined resistance measured on the loudspeaker terminals is too low the amplifier may not switch out of Standby mode until a suitable load resistance is detected For more information refer to the CAP5 section of this manual Note When using one pair of speakers use speakers with a nominal impedance of between 4 8 ohms When using two pairs of speakers use speakers with a nominal impedance of between 6 8 ohms each 4 Mode Press to switch between Volume and Balance modes Press and hold to to enter the 840A V2 System Configure menu 5 Infrared sensor Receives IR commands from the supplied Azur remote control A clear unobstructed line of sight between the remote control and the sensor is reguired 6 amp 7 Input select buttons Push the appropriate input selection button to select the source component that you wish to listen to highlighted by a solid circle on the display The signal selected is also fed to the Tape Out sockets so that it may be recorded The input should not be changed whilst recording but the recorded signal can be checked using the tape input Tape Monitor ABUSreapy Volume ingosnite Display LCD used to control the 840A V2 Please refer to the Operating
31. minal is the negative output Care should be taken to ensure no stray strands of wire short the speaker outputs together Please ensure that the loudspeaker terminals have been tightened completely to provide a good electrical connection It is possible for the sound quality to be affected if the screw terminals are loose Note When using one pair of speakers use speakers with a nominal impedance of between 4 8 ohms When using two pairs of speakers use speakers with a nominal impedance of between 6 8 ohms Please also note that when multiple speakers are connected across the amplifier s outputs the load as seen by the amplifier is reduced This will make the amplifier work harder and hotter 4 IR Infrared Emitter In Allows modulated IR commands from multi room systems to be received by the amplifier Commands received here are not looped out of the Control Bus Refer to the Custom installation section for more information S Control Bus In Allows un modulated commands from multi rooms systems or other components to be received by the unit Out Loop out for control bus commands to another unit Also allows the 840A V2 to control some Cambridge Audio units 6 RS232C The RS232C port allows external serial control of the 840A V2 for custom install use A full command set is available on the Cambridge Audio website at www cambridge audio com This port can also be used by Cambridge Audio service personnel for
32. ng antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Ventilation IMPORTANT The unit will become hot when in use Do not stack multiple units on top of each other Do not place in an enclosed area such as a bookcase or in a cabinet without sufficient ventilation Ensure that small objects do not fall through any ventilation grille If this happens switch off immediately disconnect from the mains supply and contact your dealer for advice Positioning Choose the installation location carefully Avoid placing it in direct sunlight or close to a source of heat No naked flame sources such as lighted candles should be placed on the unit Also avoid locations subject to vibration and excessive dust cold or moisture The unit can be used in a moderate climate This unit must be installed on a sturdy level surface Do not place in a sealed area such as a bookcase or in a cabinet Any space open at the back such as a dedicated equipment rack is fine however Do not place the unit on an unstable surface or shelf The unit may fall causing serious injury to a child or adult as well as serious damage to the product Do not place other equipment on top of the unit Due to stray magnetic fields turntables or CRT TVs should not be located nearby
33. nty period must be presented to obtain warranty service This Warranty is invalid if a the factory applied serial number has been altered or removed from this product or b this product was not purchased from a Cambridge Audio authorised dealer You may call Cambridge Audio or your local country Cambridge Audio distributor to confirm that you have an unaltered serial number and or you purchased from a Cambridge Audio authorised dealer This Warranty does not cover cosmetic damage or damage due to acts of God accident misuse abuse negligence commercial use or modification of or to any part of the product This Warranty does not cover damage due to improper operation maintenance or installation or attempted repair by anyone other than Cambridge Audio or a Cambridge Audio dealer or authorised service agent which is authorised to do Cambridge Audio warranty work Any unauthorised repairs will void this Warranty This Warranty does not cover products sold AS IS or WITH ALL FAULTS REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER CAMBRIDGE AUDIO SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY IN THIS PRODUCT EXCEPT TO THE EXTENT PROHIBITED BY LAW THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSOEVER INCLUDING BUT NOT LIMITED TO THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL
34. plifier and Cambridge Audio Azur CD players Insert the supplied AAA batteries to activate The functions relevant to the amplifier are as follows Standby On Switches the amplifier between On and Standby mode Numerical buttons 1 8 Press to change the input source to the amplifier Button 8 toggles Tape Monitor on off Bright Adjust the backlight of the front panel O display bright dim or off Mode Press to switch between Volume and Balance modes Mute Mutes the audio on the amplifier The mute mode is indicated by MUTE appearing and the volume level being replaced by two flashing dashes in the display Press again to cancel mute OS Volume Increase or decrease the volume of the amplifier output The functions relevant to a connected Azur CD player are as follows Open Close Opens and closes the disc tray EP Play Stop Pause Press the relevant button to play stop or pause the CD 006 Skip Right Skip Press once to skip forward by one track on the CD Press and hold to skip forwards through tracks Left Skip Press once to skip backward by one track on the CD Press and hold to skip backwards through tracks E Search Press and hold to search within the selected track Right button to fast forward left button to rewind Repeat Random Remain Refer to the Operating instructions section of your CD player manual for information on the
35. rs DAB or FM AM tuners etc Note These inputs are for analog audio signals only They should not be connected to the digital output of a CD player or any other digital device Gi Tape Rec In Out Connect to a tape deck or to the analog output sockets on a MiniDisc portable digital music player or CD recorder using an interconnect cable from the recorder s Line Out sockets to the amplifiers Tape In sockets The Tape Input circuit of the 840A V2 is a monitor type different from the other 7 inputs For the 7 normal inputs the source selected for listening to will be sent out of the Tape Out for recording The source currently being listened to and optionally recorded is then shown on the front panel display However when the Tape Input is selected a solid circle will appear beside TAPE MON indicating that the Tape Input is now being listened to with a different source being sent out of the Tape Out for recording The recording source is also shown by a solid circle by the selected input and can be changed by pressing the other source buttons To switch Tape Monitor off simply press the Tape Mon input select button again toggling this function off This feature is most useful when using 3 head analog cassette decks which allow the signal being recorded to be played back live off tape via a 3rd head whilst it is simultaneously recorded It is then possible by toggling the Tape Monitor input on and off to compare directly in real tim
36. software updates T A BUS Ready Incognito Ready multi room outputs PSU Connect an Incognito PS5 to supply power to the connected multi room keypads speakers Keypad 1 2 Connect one or two Incognito A BUS KP10 keypads or other A BUS compatible keypads using CAT 5 5e cable Incognito AS10 Active Ceiling Speakers can also be connected here IR Four IR outputs for remote control of source equipment Please refer to the Multi Room section of this manual for more information on connections and set ups Input 1 Balanced Audio Input 1 features either unbalanced phono RCA or balanced XLR connections Either type may be used but not both at the same time The balanced connection is the higher quality option and can reject noise and interference in the cable when used with other equipment that supports this function An XLR connector is wired Pin 1 Ground Pin 2 Hot in phase Pin 3 Cold phase inverted Use the Balanced Unbalanced switch Item 9 to select the connection type you wish to use When using either the balanced or unbalanced input make sure that no cables or equipment are connected to the unused input as this may degrade operation The unused input does not require to be terminated and this should not be done Q Input 1 Balanced Unbalanced switch Use to select the connection type for Input 1 Inputs 1 7 These inputs are suitable for any line level source equipment such as CD playe
37. stem Configure menu Press the input select button to turn off the volume in decibels Press the Mode button to exit Front IR uu OD S CONFIGURE lan Used in conjunction with Custom Installation C I systems or IR repeater systems it may be desirable to disable the front panel IR by setting FRONT IR to off press the input select button to turn off Press the Mode button to exit Input gain trim a 33 op ak a The relative levels of the inputs can be adjusted by gain trim This allows each to be adjusted so that each sounds the same in terms of average loudness when you switch between them Pick the loudest sounding source and trim its level until it matches the average perceived level of the others Repeat this process if other sources also stand out as louder than the average i m W Dari i i Da Da OOOO to 9 i ca Volume To set the input gain trim for each source select INP TRIM in the System Configure menu Select the input required and use the volume control to set the gain between O and 12 dB the available range is restricted if the volume is set very low Press the Mode button to exit Fixed level inputs Any input of the 840A V2 is able to be set for fixed gain Whenever this input is selected the gain will automatically go to this value and will not be adjustable by the volume control This feature allows the 840A V2 to be effectively used as
38. to edit Press EXT CHAR to access an extended character set Press OK to confirm and exit the input name change menu OOOO Volume System Configure menu Q a Press and hold the Mode button to access the System Configure menu The menu options are Clip detector LCD brightness Speaker short detector Input gain trim Volume ramp Volume display Front IR and Fixed input gain OOOO Volume To exit the System Configure menu and its sub menus press the Mode button again Clip detector Speaker short detector Refer to the CAP5 section of this manual for more information on the Clip and Short detection features of the 840A V2 as both can be enabled default or disabled LCD brightness Mode CONFIGURE OOOO Volume In the System Configure menu press the LCD input select button to scroll through bright dim off settings for the front panel display Press the Mode button to exit Volume ramp Mode e O o fern wy e INP TRIN Pontes tit wami The 840A V2 automatically ramps the volume down when going into Standby mode and up when coming out of Standby mode To turn this feature off press the VOL RAMP input select button in the System Configure menu and set to off Press the Mode button to exit Volume display Volume To change the volume display from decibels 95 to OdB to arbitrary volume units O to 96 units select VOL DB in the Sy
39. ure your system realises its full potential Thank you for taking the time to read this manual we do recommend you keep it for future reference Met Bei ee Matthew Bramble Cambridge Audio Technical Director and the Amplifier design team Rear panel connections azur Power Oc ambridge Audio Designed in London Englar D on EH ott azur 840A V2 0 Class XD Integrated Amplifier www cambridge audio com Power Rating 230V AC 50Hz onsumpti 9002 a N1863 IR Emitter Control Bus YA LO Multi Room wepesi m J ins out ane ano duwaid ang ede ujadey 1 4 00 OO Preamp Out Tape Out Tape in Input 7 Input 6 Input 5 Input 4 4 Power On Off Switches the unit on and off 2 AC power socket Once you have completed all connections to the amplifier plug the AC power cable into an appropriate mains socket then switch on Your amplifier is now ready for use 3 Loudspeaker terminals Two sets of loudspeaker terminals are available A main loudspeaker terminals and B secondary loudspeaker terminals Both sets of speakers can be turned on and off independently Connect the wires from your left channel loudspeaker to the LEFT amp terminals and the wires from the right channel loudspeaker to the RIGHT amp terminals In each case the red terminal is the positive output and the black ter
40. using this product as easy as possible Information in this document has been carefully checked for accuracy at the time of printing however Cambridge Audio s policy is one of continuous improvement therefore design and specifications are subject to change without prior notice This document contains proprietary information protected by copyright All rights are reserved No part of this manual may be reproduced by any mechanical electronic or other means in any form without prior written permission of the manufacturer All trademarks and registered trademarks are the property of their respective owners Incognito and Incognito Ready are trademarks of Cambridge Audio Ltd All rights reserved Class XD Technology International Patent Pending Cambridge Audio Ltd Copyright Cambridge Audio Ltd 2008 A BUS and A BUS Ready are registered trademarks of LeisureTech Electronics Pty Ltd Australia This product may be covered by one of more of the following patents US 7 181 023 6 389 139 EP 1004222 AU 739808 NZ 502982 Mexico Z41196 Canada CA2301062 iPod and Apple are trademarks of Apple Inc registered in the U S and other countries Introduction Thank you for purchasing this Azur 840A V2 Class XD Integrated Amplifier We hope that you will enjoy many years of listening pleasure from it The 840A V2 features our unique proprietary amplifier topology Class XD designed to eliminate crossover distortion at low signal lev

Download Pdf Manuals

image

Related Search

Related Contents

46451.1 EFL UMX F-16 BNF Basic manual.indb  Service Manual Technics SL1200Mk2  PCR clean-up  SAFETY-AT057B-PT-E, Função de segurança  Manual do Usuário do iPod shuffle  く取扱説明書)  Instrucciones de instalación y operación Panel de control para  

Copyright © All rights reserved.
Failed to retrieve file