HOBBES LANtest Multinetwork Cable Tester
Contents
1. end of the master unit Remote Test Sample Test Results 123456786 1 Continuity Pin 2 has continuity 123456786 2 0pen Pin 2 is opened 123456786 3 Short Pin 2 and Pin 3 are shorted 123456786 4 Miswire Pin 3 and Pin 6 are miswired Caution 1 Operating the tester in live circuits may damage the tester 2 Leaving the battery in the tester for long periods of time without use could drain power from the battery2. Hobbes INNOVATION LANtest Kit Operations Manual For 256551 LANtest Kit Hobbes GmbH Jacobsenweg 1 22525 Hamburg Germany Hobbes INNOVATION 1 LANtest Kit CONTENTS INTRODUCTION o FEATURES ou o a PACKAGE CONTENTS cn a PRODUCT PROFI Esas ME A e uen 1 10Ba56 T A E ME ne SSE EAS EETRI EnS OPERATION nada aaa E er ear Titre 2 FLL Modular Cable Testa ogena aa 3 Coaxial Cable Tesi ll Remote Tetuan rondes A RA Hobbes INNOVATION 2 LANtest Kit INTRODUCTION The LANTEST KIT Network Cable Tester is an innovative practical tester that can easily read the correct pin configuration of 10BASE T 10BASE 2 RJ45 RJ11 modular 258A TIA 568A 568B and Token Ring cables by comparing one transmitting end to the corresponding receiving end The included remote terminator allows the user to test installed cable either at a wall jack or a patch panel Verifying continuity and testing for faults such as open shorted and crossed pairs has never been easier and more affordable FEATURES Displays the actual pin configuration of 10BASE T and 10BASE 2 Ethernet RJ45 RJ11 modular 258A TIA 568A 568B and Token Ring cables Provides easy to read continuity and fault status display Checks for continuity open wire shorted pair and crossed pair faults Allows for remote testing of installed cables from wall jack or patch panel Tests shield wire integrity Auto or manual scanning PACKAGE CONTEN
3. TS LANTEST KIT Master Unit LANTEST KIT Remote Unit RJ45 Male to BNC Male Adapter Cable Qty 2 RJ45 UTP Patch Cable BNC Female Female Coupler RJ45 RJ11 Jack Size Adapter Qty 2 RJ45 JACK RJ45 JACK LED DISPLAY FOR SOURCING END JACK 1 LED DISPLAY FOR RECEIVING END JACK 2 POWER SWITCH LED SCANNING MODE SWITCH TEST SWITCH FOR MANUAL SCAN RJ45 JACK LED DISPLAY FOR RECEIVING END SAME AS JACK 2 10 GROUND LED FOR RECEIVING END 11 BATTERY COMPARTMENT 9V VO Y QU E UNFP OQ UE UN A Hobbes INNOVATION 3 LANtest Kit PRODUCT PROFILE I Loopback Test 1 10Base T Test 1 1 Plug one end of the tested cable into the transmitting RJ45 jack on the master unit marked with a and the other end of the cable into the remaining receiving RJ 45 jack 1 2 Slide power switch on The upper row of LEDs will start to scan in sequence if the Auto Manual button is set on Auto mode The LED for pin 1 will light up if the button is in Manual mode 1 3 Switch back and forth from Auto or Manual scanning mode by pressing the Auto Manual button on the side of the master testing unit 1 4 Once both ends of the cable are plugged in properly the second row of LEDs will illuminate according to the corresponding LEDs in the top row 1 5 Read the results of the LED display for the pin configuration status of the tested cable If you fail to read the results the first time in Auto mode you may
4. wait for the second LED scan or simply switch to Manual mode for pin by pin testing In Manual mode pressing the square Test button will advance testing to the next pin OPERATION Note Make sure the battery power is sufficient Insufficient battery power will lead to dimmed LEDs and incorrect results 2 RJ 11 Modular Cable Test 2 1 Please follow directions for the UTP STP Cable Test and use the operations manual for the correct LED pin out display 3 Coaxial Cable Test 3 1 Plug the two attached BNC adapter cables on both RJ 45 jacks Then connect the tested cable to each end of the BNC adapter cables Hobbes INNOVATION 4 LANtest Kit 3 2 For the remaining testing procedures please refer to steps 1 2 to 1 5 Note 1 The center pin of BNC should be read on LED 2 2 As Coaxial cable has only two wires we suggest you read the result of the LED scan using Manual mode Il Remote Test 1 Plug one end of the tested cable to the transmitting RJ 45 jack on the master unit marked with a and plug the other end into the remote terminator If the tested cable is installed in a patch panel or wall plate you may use the included patch cable to solve the connector gender problem 2 Now set the Auto Manual switch to Auto mode for one person testing 3 Read the test results from the LED display on remote terminator Note The LED display on the remote unit will scan in sequence corresponding to the transmitting
Download Pdf Manuals
Related Search