Home

Intellinet Wireless B Print Server

Contents

1. An IP address can be automatically assigned to the print ae server by a DHCP server If your network does not have a DHCP server please specify an IP address for the print Print Server SE Configuration Ze Obtain an IP address from a DHCP server pe Specify an IP address ay OK gt lt Cancel Obtain an IP address from a DHCP server This option enables or disables the DHCP feature of the print server When this option is enabled the print server will obtain an IP address automatically from the DHCP server on your LAN The default value is Disable Note 1 Once this option is enabled the following IP address Subnet Mask Gateway will be grayed out and are not available for editing 2 While the print server supports DHCP we strongly recommend you manually specify a fixed IP address to the print server Specify an IP address IP Address This option shows the print server s current IP address maybe obtained from your DHCP server or manually specified This option also allows you to manually specify an IP address to the print server if DHCP option is disabled Subnet Mask This option shows the print server s current subnet mask maybe obtained from the DHCP server or manually specified This option also lets you manually specify a subnet mask to the print server if DHCP option is disabled This value is optional Gateway This option shows the print server s current gateway address maybe obta
2. 9 Done 72 Appendix Diagnostic Mode If you had problems to setup your print server in your wireless network please refer to the following steps 1 Change the print server to diagnostic mode by switching the DIP switch to DIAG mode the side near to power connector 2 Change your wireless adapter to 802 11b Ad hoc mode and the ESSID is WLAN PS 3 Run PSAdmin to discover the print server 4 Select the wireless print server Inia File view Help gt fi gt Sx0 3 ala A 21P_PrintServS35B04 00 40 01 53 5B 04 DEFAULT_PS_NAME Off Line Model 20 Version 6 08 20E A A g Ports e Wireless NetWare TCP IP fl AppleTalk fs Advanced Dm 1P_PrintServ535B04 5 Select wireless and input the ESSID Channel Rates that meet your network environment then press ok 18 6 ir printservsasoos properties x A General S Wireless G tcpap Sy merware C ap gt Arel ess Setting The page allows you to set up this print server to be an Access Point or a wireless station on the network Print Server Configuration Mode infrastructure e ESSID J ts ap Channel 9 1 14 Basic Rates fi 2 5 5 11Mbps Advanced WEP General 7 Done The print server will restart 8 Switch the DIP back to normal mode and change your wireless adapter setting Load Default Value You can load the default value o
3. 7 Turn on the power of your printer s to begin printing Wireless Network Environment Infrastructure AP Mode e Access Pomt Winodws PC Mactintosh Ad hoc PEER to PEER Mode Wireless Print Server Printer Laptop Winodws PC Mactintosh 2 Print Server Installation Preparation To meet users network printing needs in today s heterogeneous and multiple protocol networking environments the print server supports industrial standard protocols including TCP IP IPX SPX NetBEUI and AppleTalk This means that the print server supports the most popular network operating systems today including NetWare Windows 95 98 Me NT 2000 XP UNIX systems and Macintosh computer As such there might be several ways to deploy the print server on your network Supported Networks Print server supports a variety of network protocols including TCP IP IPX SPX NetBEUI and AppleTalk In addition we provide software for network configuration on the following networks e Novell NetWare 3 12 4 x 5 x Bindery NDS and NDPS e Microsoft Windows 95 98 Me e Microsoft Windows NT 2000 XP 2003 e Apple EtherTalk e UNIX Linux system e Internet via Internet Printer Connection software Configuration Solution Table setup Operating Function Remarks System PSAdmin utility Windows Install a single Easy printer installation runs from CD 95 98 Me network on a Windows peer to peer or NT 2000 XP 2003 clien
4. The program will save the above settings into the print server Done 17 NetWare Wizard 1 Log into your NetWare file server as a Supervisor Admin or equivalent 2 Click Wizard button just like a picture lt N gt and select NetWare Wizard as follow picture War NetWare Wizard Configuration Wizard C WW E tf wm Di Linux UNIX Windows 95 Windows 98 Windows NT NetWare NetWare Vizard CAA Print Server Name DEFAULT_PS_NAME i NetWare Server FS 01RD 4312 y Print Server Queue s 4 pse 018 4 Type in a Print server 5 Type in a Print Queue Names Note Each print queue corresponds to each print port of the print server 6 Click OK 7 Done 8 From your NetWare client computer such as Windows 95 98 Me create a printer that is connected redirected to one of the NetWare print queues serviced by the print server Manual Setup Manual Setup is a configuration program designed for more experienced users of NetWare To setup the print server by using Manual Setup follow the steps 1 Run PCONSOLE in NetWare 3 x or NetWare 4 x and create the necessary parameters Refer to your Novell NetWare print server Services manual for details 2 Log into your NetWare file server as a Supervisor Admin or equivalent From your Windows 95 98 Me run PSAdmin 3 Select the print server that you wish to configure B
5. When installed on a supported host server HP Web JetAdmin can be accessed from any client through a supported Web browser by browsing to the HP Web JetAdmin host Installing HP Web JetAdmin Before installing the HP Web JetAdmin software you must have domain administrator or root privileges Download the installation files from HP Customer Care Online at http www hp com go webjetadmin Follow the instructions on the screen to install the HP Web JetAdmin software Note Installation instructions are also contained in the HP Web JetAdmin install file Confirming Installation and Supply Access e Confirming that the HP Web JetAdmin software is correctly installed by navigating to it with your browser as shown in the following For example http server domain port where server domain is the host name of your web server and port is the port number assigned during installation e Supply users access to HP Web JetAdmin software by adding a link to your web server s home page that is addressed to HP Web JetAdmin s URL For example http server domain port Configuring and Modifying a Device Using your browser navigate to HP Web JetAdmin s URL For example http server domain port Follow the instructions on the appropriate home page to configure or modify your printer Note You can also substitute the server domain with TCP IP address 27 Removing HP Web JetAdmin Utility To remove HP Web Je
6. previous section in this chapter for details 2 If you use Mac OS 8 x or 9 x please make sure your printer support PostScript 5 Click Setup button and choose the PPD file matching your printer and click OK If your printer does not appear in the PPD file list please contact your printer vendor You may also use the Generic PPD if you do not need any printer specific features 6 Close the Chooser Windows 7 Done 45 6 Network Print Monitor Preparation The print server supports TCP IP IPX SPX and NetBEUI protocols under Windows 95 98 Me Please make sure that the following steps have been completed before proceeding with installation under Windows PC Select A Desired Protocol TCP IP O The TCP IP Protocol must be installed For further information please read TCP IP Protocol Installation section in this chapter Note If TCP IP protocol is chosen please refer to Assigning an IP Address to the print server section later in this chapter IPX SPX The IPX SPX compatible Protocol must be installed For further information please read IPX SPX compatible Protocol Installation section in this chapter NetBE Ul The NetBEUI protocol must be installed For further information please read NetBEUI Protocol Installation section in this chapter 46 TCP IP Protocol Installation 1 8 9 Click Start point to Settings and select Control Panel Double click the Net
7. 77 Trademarks NetWare is a registered trademark of Novell Inc and Windows 95 98 Me and Windows NT 2000 XP are registered trademarks of Microsoft Corp All other brands and product names are trademarks of their respective companies Copyright No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without the express written consent of the manufacturer as stipulated by the United States Copyright Act of 1976 FCC Compliance Notice Radio Frequency Notice This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference may cause undesired operation Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be
8. Port and click OK 16 The Add Port box will then appear along with the print server s Node ID The last 6 digits of the Node ID located on the back of the print server unit Select one printer server port from the list which is now connected to one of your printer s as shown in the following picture 49 Add Port ES ix F Tcen zapen ok cael Device Name pm Node versal 2 1P_PrintServ43D452 1 004DO143D452 5 0 AJ 3P_PrintServ43FF9A 00400143FF9A 6 0 About A 3P_PrintServ43FF9A 00400143FF9A ep A 3P_PrintServ43FF9A el A 1P Printserv430FDE 3 2 00400143FF94 004001430FDE WH rs Port Information Port name LPT P50311 1 Transmission timeout 90 seconds H By default the computer will first search for the print server s on the network by using the IPX SPX protocol m lf the IPX SPX protocol is installed the print server will be displayed along with its Node ID as shown in Node column The last 6 digits of the Node ID located on the back of the print server unit Select one of the print server s ports from the list m Ifthe IPX SPX protocol is not installed no print server will be shown in the display box Then please select TCP IP or NetBEUI alternatively E It starts again to search for the print server on the network by using the protocol you specify in the step above When finished the print server will be displayed along with the its Node ID as shown in the fo
9. from the bottom left hand corner of the screen Point to Settings and select Control Panel Double click the Network icon Select Protocols Select the NWLink IPX SPX Compatible Transport Select Properties Select your first network interface card and select Manual Frame Type Detection Click Add In the Frame Type field select Ethernet 802 2 In the Network Number field type in an unique 8 digit hexadecimal network number For example 12345ABC 10 Select Add 68 11 Repeat the Steps 8 12 for the other Ethernet adapter 12 Restart the computer 13 Done Moving the print server to A New Segment If the print server is moved from one network segment to another after the initial installation through the Network Print Port the print server must be reconfigured on the original Windows NT server or on each Windows 95 98 computer using this print server in order for the print server s driver on each computer to re establish a new connection Print Server Reconfiguration Procedure on Windows 95 98 Me 1 Click Start on the bottom left hand corner of the screen 2 Select Settings and select Printers 3 Select your printer connected to the print server and right click the printer icon Select Properties 4 Click Details tab 5 Click Port Settings as shown in the picture below The print server will be displayed on the next print server s configuration screen Find your original print server according to its Port N
10. is located in your current working directory 2 At NT 2000 XP s DOS prompt and type tftp lt print server s IP address gt get upgrade 3 Type tftp i lt print server s IP address gt put mpsXX bin 4 Wait for the transfer successful message 64 5 Done Upgrading the print server from UNIX Through TCP IP l 2 gre Log in as root Ensure binary file is located in your current working directory Type tftp lt print server s IP address gt At tftp prompt type get upgrade Change to binary mode At tftp prompt type put mpsXX bin Wait for the file transfer to complete Quit from tftp Done Upgrading the print server from Browser Ensure binary file is located in your current working directory Enter the IP address of the print server as the URL Click Misc and then choose Upgrade From Browser it then as shown in the following picture al 1P_PrintServ535A07 LE This page allows you to upgrade the firmware of the print server Note Please make sure that you use the correct firmware before you proceed If you do not know which firmware you should use please contact your local dealer for technical support Firmware Upgrade Select A Firmware File Browse Parade Click Upgrade form Browser and select the firmware file 65 5 6 Click Upgrade Done 66 9 Troubleshooting General Troubleshooting Overview The most
11. meet the IP addressing requirements of the network segment Gateway s IP This option allows you to view gateway from the print server This IP address of gateway must meet the router or gateway to go across of the network segment Netware Status 1 Click Status it then appears the sub menu 2 Click Netware it then as shown in the following picture Y This page displays the current NetWare settings of the print server General Settings Print Server Name DEFAULT_PS_NAME Polling Time 3 seconds NetWare NDS Settings Use NDS Mode Disable Name of the NDS Tree Name of the NDS Context Current Status Disconnected NetWare Bindery Settings Use Bindery Mode Disable Name of the File Server Current Status Disconnected 33 General Settings Print Server Name This option allows you to view print server s name would be configured by PSAdmin utility Polling Time This option allows you to view polling time from the print server This function is search for NetWare Server by per time NetWare NDS Setting Use NDS Mode Enable or Disable Name of the NDS Tree Name of the NDS Content Current Status Connect or Disconnect NetWare Bindery Setting Use Bindery Mode Enable or Disable Name of the File Server Current Status Connect or Disconnect SNMP Status 1 Click Status it then appears the sub menu 2 Click SNMP it then as shown in the following picture 1P_PrintServ535A07
12. not seem to proceed again while upgrading the print server Possible Explanation There might be a network problem This causes the upgrading procedure to fail Solutions 1 Check the network cabling especially from the workstation running the PSAdmin to the print server unit 2 Run the PSAdmin and upgrade the print server again 75 Question D The Status LED light keeps blinking after POST Possible explanation and solution The last upgrade process was not completed The print server must be upgraded again by using the PSAdmin Please see Chapter 3 for details Question E The PSAdmin reports Create Print server Error Create Printer Error or Create Print Queue Error while using Auto Setup Possible Explanation The print server name the printer name or the print queue name you specified in the Auto Setup dialogue box contains a space Solution Check to see if there is a space in the print server name the printer name or the queue name Type in a new name without a space between two characters or replace a space by a dash or an underscore _ Question F The PSAdmin reports Print server Already Exists Printer Already Exists or Print Queue Already Exists after specifying the print server name or the print queue name in Auto Setup Possible Explanation A same print server name or queue names exists in the specific NetWare file server as the one you specified in the Auto S
13. 2 lf the solution described above is not applicable you have to follow the instructions below to set up the print server s IP address For the purpose of explanation we assume the NT server is on Segment A and its IP address is 192 72 214 66 subnet mask 255 255 255 224 the print server is going to be installed on Segment B with IP address for example 192 72 214 100 1 Find an unused IP address on Segment A for temporary use in the following steps for example 192 72 214 68 2 Connect your print server to Segment A as a networked node 3 On your NT server type for example arp s 192 72 214 68 00 40 01 3F 02 AB Please note in this arp command you have to type 192 72 214 68 on purpose Do not type this IP address as 192 72 214 100 4 Type tftp 192 722 214 68 get config txt The configuration file will then be retrieved and transferred to your NT server 71 5 Type edit config txt to modify this configuration file 6 In your editor modify BoxlPAddress field from 0 0 0 0 to 192 72 214 100 Leave other options as default and do not change their values When done save this new file and quit from your editor Please note in this step you must specify an IP address which is valid on Segment B such as 192 72 214 100 in this example rather than 192 72 214 68 7 Type for example tftp 192 72 214 68 put config txt to save this new configuration back to print server 8 Move the print server back to the Segment B
14. AN IP ADDRESS sil sa 51 WINDOWS NT LPR PORT DRINTINGINSTALLATION 52 WINDOWS 2000 XP STANDARD TCP IP PORT DGINTINGINSTALLATION 53 UNIX INSTALLATION A egenen eee a eat Shh ae ne dl dd nba lakh secant ales 56 S UPGRADING PRINT SERVER cionado 64 OVER AE EA AAA LAA E IE 64 UPGRADING THE PRINT SERVER FROM PSADMIN s ssssssssssrrssressrrssrreserressrrssressrreseressrressressressrreset 64 UPGRADING THE PRINT SERVER FROM WINDOWS NT 2000 XP THROUGH TCP IP 64 UPGRADING THE PRINT SERVER FROM UNIX THROUGH TC 65 UPGRADING THE PRINT SERVER FROM BROWSER sssssssssssssssssseessereessesressssrresssrressserrossereessssressssre 65 9 TROUBLESHOOTING soon dis 67 GENERAL TROUBLESHOOTING OVERVIEW ccccccssssscesssscssscecssscecessescesssecssssscssssecssesecssseessssseessnees 67 POWER RELATED PROBLEMS nia 67 PRINT PORT RELATED PROBLEMS a a a SS 67 WINDOWS 95 98 ME NT 2000 XP TROUBLESHOOTING ssssesssssssersssresrressressreesserssressrresrressreessee 68 MOVING THE PRINT SERVER TO A NEW SGEOGMENT 69 MOVING YOUR COMPUTER TO A NEW GEOMENT 70 NOVELL NETWARE TROUBLESHOOTING cccccccsssscssssccssssecssssccssscecssseecssseecssesesssssecssesessseseseners 70 TCP IP e TR ele 70 APPENDIX sanitaria co dan id 73 LO ADDEFAULT VALUES A A A E A O hoa 74 FREQUENTLY ASKED HEEN aid dal engt arse nda Waneibeu tenia 75 ADDITIONAL INSTALLATION INSTRUCTIONS ccccccccccccssccccsseceesseceesseceesseceessecessecssseceseeesseeessseeees
15. Name In this option type a name for identification purpose or just leave it in default recommended Note The default print server s Chooser name is as shown as follows lt ATALK_PS gt xxxxxx 1 where xxxxxx represents the last six digits of the device s Node ID For example ATALK_PS 40EEED 1 You may also change the lt ATALK_PS gt to a name you like for identification purpose in this option The print server will append the last six digits to the name you specify 5 Printer Type In this option the LaserWriter of printer type by default recommended 6 Data Format In this option data format includes ASCII TBCP and BCP Setting Up a Macintosh Computer 1 Ata Macintosh computer from the Apple menu select Chooser 2 The Chooser window then displays an Apple Zone list Select the Zone name that you specified when configuring the PRINT SERVER Note If you select a Zone that the PRINT SERVER doesn t belong to as you specified in the previous section no N7119 will be displayed in the Step 4 3 Ifyou are using a PostScript printer you can select the LaserWriter 8 icon 4 The Chooser window then displays PRINT SERVER s featuring the support for AppleTalk protocol along with its default Chooser Name in the right hand Select A PostScript Printer dialog box Note 1 You may change the default Chooser name and Zone name of a PRINT SERVER by using your web browser before proceeding with this installation Please see the
16. Print Server Setup Wizard next to Select A Print Server install the print server on this computer Configure Wireless Setting Click Finish to close this Wizard Configure TCP Setting Save Settin Complete 15 Using PSAdmin After PSAdmin is successfully installed run the program by double clicking the PSAdmin icon from Network Print Server program The screen will then appear as follow picture e PSAdmin _ e File View Help S N ola ala a MAC Address Print Server Name Status EZ 1P_PrintServS35407 00 40 01 53 54 07 DEFAULT_PS_NAME 6 08 21E OFF Line S MAC Address 00 40 01 53 54 07 Model 21 Version 6 08 21E if E Ei Ports a 3 Ip al Wireless gt 7 Sat NetWare 1P_PrintServ535407 ER S TCP IP El el AppleTalk All print server s feature Novell NetWare function on the LAN will be displayed along with their respective device name MAC Address print server name firmware version and status The terms are defined as follows Device Name The name of the print server hardware used for identification purposes MAC Address The Ethernet address of the print server Print server Name The print server to which the device is attached Version The firmware version of the print server Status To come up a Printer s status presently Wizard Wizard is a configuration program that can assist you in setting up the necessary parameters for your print server device to function Setup a print
17. TABLE OF CONTENTS COPYRIGHTS ol it ads o o is e idol e Does de 3 PAINTRODUG TION orc cssccciccsvsveccsscecccccascssdecetecescepeasecsesdoccdcciccsecvescoscecbessessescause obtesceeesdeesecctsosecessesectees 4 PRODUCT OVERVIEW ict a Ee EE 4 WIRELESS SPECIFICATIONS it A A eda La eL dE 4 COMPONENTS AND FEATURES tontos tsebo tte Sosse PEPEE PS S SPEER EEES Sesser EEEo eseese nnt 5 HARDWARE INSTALLATION neiii n er a a a a a a a a a ai 6 WIRELESS NETWORK ENVIRONMENT 7 2 PRINT SERVER INSTALLATION o ooccccccocoononconoccncccconoonononnnncnccocononnnonnononcconoonooonnnnoncnoconoonanonnnnos 8 PREPARATION ia ts anne tse ohne e o E o o then et ad 8 CONFIGURATION SOLUTION TABLE 8 3 THE PSADMIN UTILITY FOR WINDOWS BASED ccccococnnncccccccccoconoononocconococonococonanonococonos 10 INSTALLING THE DBGADMIN tets ss stbr toto os esst s ttre sessast ebreos oses sene renees esene 10 USING e TEE 16 WIZARD a o o oa 16 WMANUALESE PUPS Be unta ta e a on te Aba AG le a loe ted Seah tok e e So 18 REFRESH tot te e taa Rs al ea Ue dl land fa os EI gl ea o A ae 21 MULTIPLE PRINT QUEUES CONFIGURATION sssssssssssesssssssesereesessssrsrroreessssssrtretsessssesrrereosssseserereess 22 UNINSTALLING THE PSADMIN ON WINDOWS PC i i cccccccccccccesececececececececececececececececececececesecececeeeees 22 4 INTERNET PRINTER CONNECTION AND HP WEB JETADMIN cccccoccsssssssooes 24 IPPLOVERMIE WA Ee de ea es 24 HP WEB JETADMIN OVERVIEW cccesses
18. This option allows you to view data format from the print server If you are using a PostScript printer you can select ASCII TBCP or BCP format from web configuration Setup Menu Meanwhile you have finished the IP address configuration with print server You should use web browser to configure the print server The setup menu of the print server helps administrator to setup the print server s System Printer NetWare TCP IP SNMP and AppleTalk Preparation Enter the IP address of the print server as the URL for example 192 168 10 132 Then the print server s home page will appear in content of the web browser Please follow this information in the setup menu of the print server System Setup 1 Click Setup it then appears the sub menu 2 Click System it then as shown in the following picture el 1P_PrintServ535A07 L This setup page allows you to configure general system settings of the print server System Settings Device Name NP_PrintServ535A System Contact System Location Administrator s Password Password 3 8 characters Re type Password ave estar Device Name This option allows you to input device name of the print server To correct the print server s device name 36 System Contact This option allows you to input contact name of the print server To check the print server s contact name who in charge of this device System Location This option allows you to input L
19. Y This page displays the current SNMP settings of the print server SNMP Community Settings SNMP Community 1 public Read Only SNMP Community 2 public Read Only SNMP Trap Settings Send SNMP Traps Disable Use Authentication Traps Disable Send Traps to IP Address 1 0 0 0 0 Send Traps to IP Address 2 0 0 0 0 34 SNMP Communities This option allows you to view SNMP communities from the print server There are two communities that control message from the network management of the print server SNMP Traps This option allows you to view SNMP traps from the print server AppleTalk Status 1 Click Status it then appears the sub menu 2 Click AppleTalk it then as shown in the following picture se 1P_PrintServ535A07 Y This page displays the current AppleTalk settings of the print server AppleTalk Settings AppleTalk Zone Name Printer Information Port Name ATALK_PS 535407 1 Printer Type LaserWriter Data Format TBCP Zone Name If no any zone exists the print server itself displays the zone name as an asterisk in the current AppleTalk Status of the print server in the web browser Port Name lt ATALK_PS gt xxxxxx 1 where xxxxxx represents the last six digits of the print server s Node ID Printer Type This option allows you to view printer type from the print server If you are using a PostScript printer you can select the LaserWriter 8 icon from your Mac computer 35 Data Format
20. ack of OK Cancel 3 Select the NetWare File Server to which the print server device will be attached 4 Click Properties in the tool bar and the following screen will appear Properties button just like a picture AM as follow picture 10 100 PS Properties x E General Sy TCPAP 2 Netware C Apple Talk Ba st_4 gt m Nettare Settings gg Print Server Name ps Polling Time 3 E Sec Print Server Configuration Te a NetVVare Server FS 01RD W4312 A 2 a E a NDS Settings Kai Linux UNIX Tree Name Windows NT lj NetWare Context Windows 95 Windows 98 Encrypt Password Specify the password the print server uses to logon the SN NetvWVare server Password af OK gt Cancel 5 Select NetWare and type in the Print server that created during PCONSOLE 6 Optional In Bindery Settings Select NetWare file server s that print server can do Bindery mode 7 Optional In NDS Settings Select NetWare file server s NetWare 4 x or later that print server can do NDS mode 8 Click OK From your NetWare client computer such as Windows 95 98 Me create a printer that is connected redirected to one of the NetWare print queues serviced by the print server Properties TCP IP Options The TCP IP options allow you to modify the print server s TCP IP settings Each option is detailed as follows 19 TCPAP Settings
21. agement and a warning A standard SNMP agent is permanent on these print servers Any standard SNMP based application can be used to access and manage these print servers Network configuration The print servers provide an embedded web server that can be accessed via a prop web browser We also subsidiary Windows based PSAdmin utility which help administrator to setup print server environment For example Netware Windows 95 98 Me Windows NT 2000 XP Mac or Unix system Wireless Specifications Complies with IEEE 802 11b Direct Sequence Spread Standard Spectrum DSSS standard Radio Frequency 2 4 GHZ ISM Band Media Access Control Carrier Sense Multiple Access Collision Avoidance CSMA CA Method with ACK Modes Ad Hoc and Infrastructure User definable Data Transfer Rate 1 2 5 5 11 Mbps Output Power 13 17 dBm typical 15dBm WEP Wired EquivalentiSupport 64 and 128 bit Encryption Privacy Encryption Components and Features Wireless Print server e 1 Bi direction parallel port IEEE 1284 or USB 1 1 port support USB2 0 full speed e POST Power On Self Test e LED Lights Status Yellow color indicating Power POST process WLAN Active Green Yellow color indicating the strength of radio signal and data transmission e 1 CD for Netware Windows 95 98 Me NT 2000 XP e 1 external AC power adapter 3 3V 2A e Normal and Diagnostic Mode select by DIP switch e Built in Reset Button Before you start y
22. ame or other distinguished name and click this print server 6 Click OK and it returns to the printer s Properties page 7 Click OK 8 Done Print server Reconfiguration Procedure on Windows NT 1 Click Start on the bottom left hand corner of the screen 2 Select Settings and select Printers Select your printer connected to the print server and right click the printer icon Select Properties 4 Click Ports tab 5 Click Configure Port The print server will be shown on the next screen Find your original print server according to its Port Name or other distinguished name and click this print server Click OK and it returns to the printer s Properties page Click OK 69 9 Done Moving Your Computer to A New Segment If you are using the print server through the Network Print Port on your NT or Windows 95 98 Me computer and your computer is going to be moved onto another segment you have to reconfigure the print server on your computer to use your print server However this situation is like moving the print server to a new segment Please refer to the Moving the print server to a new segment section for more detailed reconfiguration instructions Novell NetWare Troubleshooting Many printing problems can be traced back to incorrect or incomplete print server installations t is always wise to check the installation configurations first In some cases if necessary delete the print server print queue s o
23. ame the print server is configured with stored in the print server s memory an authentication failure trap message is generated In the print server s SNMP implementation the following MIB objects are available for updating 42 MIB Object Names Description system sysContact Indicates the network administrator s name system sysName Indicates the print server s name for identification system sysLocation Indicates the location of the print server snmp snmpEnableAuthenTraps Enables or disables the function of sending SNMP Authentication Failure trap message to the network administrator if the community name within a SNMP request is not correct Users can set up print server s SNMP functions by using their browsers 1 Click Setup it then appears the sub menu 2 Click SNMP it then as shown in the following picture 5 Y This setup page allows you to configure SNMP settings of the print server SNMP Community Settings Support HP WebJetAdmin Disable DI SNMP Community Name 1 public Privilege Read Only y SNMP Community Name 2 public Privilege Read Only SNMP Trap Settings Send SNMP Traps Disable y Use Authentication Traps Disable y Send Traps to IP Address 1 nung Send Traps to IP Address 2 boon SNMP Community The print server supports up to two community names The default community name is public case sensitive with Read Only access right in default 43 Suppo
24. common problems which cause the print server to perform improperly are covered in this chapter If a problem still exists after reading this chapter please contact your dealer for technical support LED Light Indicators The print server is equipped with seven LED lights to assist in diagnosing problems that are the result of the network and or the print server hardware itself Status Red When the print server unit is powered on the Status LED will flash five times as part of the unit s Power On Self Test POST This indicates that the print server hardware is properly configured This LED however may flicker whenever the data are being transmitted and printed Note Make sure that the Red LED flashes five times POST upon connecting the power If the unit does not flash five times contact your dealer for a replacement or repair W LAN Green Data is being transmitted and received via the W LAN port Power Related Problems The print server requires an external AC power adapter in order for it to function If you have a power problem check to see whether the power cord or its connectors are damaged More importantly check to see that the AC power adapter included with the print server matches the AC voltage in your country or area Using an incorrect AC adapter will damage your print server Print Port Related Problems Printing data failure may be caused by a loose connection of the print server to the Centronics parall
25. ct 8 Done Note For more detailed information please refer to your Microsoft Windows 9X ME NT 2000 XP manuals Win 95 98 Me NT 2000 XP Installation Procedure Please perform the steps as follows to ensure a smooth installation 1 Run Setup from the print server s NetWare Win 95 98 Me NT 2000 XP Setup diskette The Network Print Monitor for Windows 95 98 Me Setup will then appear Click Next A message reading Setup is complete You may add the Network Print Port by using the PSAdmin will appear Click OK oN 4 Click Start point to Settings and select Printers 5 Double click the Add Printer icon 6 Select Local Printer and click Next 7 Select the appropriate printer manufacturer and printer type and click Next 8 Select LPT1 and click Next 48 9 Type in the Printer Name and click Next 10 A message reading After your printer is installed Windows can print a test page so you can confirm that the printer is set up properly Select No and click Finish 11 Double click the newly created Printer Name icon 12 Select Printer and Properties 13 Click Details tab and select Add Port 14 In the Add Port dialog box select Other as shown in the following picture Add Port 21x Select the type of port you want to add C Network Specify the network path to the printer Other Click the type of port you want to add Local Port Network Print Port 15 Select the Network Print
26. determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help Important Note FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment In order to avoid the possibility of exceeding the FCC radio frequency exposure limits human proximity to the antenna shall not be less than 20 cm 8 inches during normal operation This transmitter must not be co located or operating in conjunction with any other antenna or transmitter FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Part No 535Wx V17 2 1 Introduction Product Overview The external print servers enhance capability by letting you place your printers plotters or equality printers at convenient locations directly on the Ethernet network and by increasing network printer performance and management Network Management The print servers support the Simple Network Management Protocol SNMP which remote printer man
27. e ping 192 72 214 103 You should get the responses from the print Server 4 Type tftp lt Print server s IP address gt For example tftp 192 72 214 103 At the tftp prompt type get config txt to retrieve the Print Server s configuration file For example tftp gt get config txt 5 Quit from tftp and then use your editor to modify the 05 BoxlPAddress field in the config txt file from 0 0 0 0 to the IP address you specify in Step 2 6 Optional Modify the 06 Gateway field from 0 0 0 0 to your gateway s IP address 7 Optional Modify the 07 SubnetMask field from 0 0 0 0 to the subnet mask 8 When done save the new config txt 9 Type tftp lt Print server s IP address gt At the tftp prompt type put config txt to save the new configuration file back to the Print Server For example tftp gt put config txt 10 Type mkdev rlp 56 After this step the Remote Printer Configuration appears Answer the questions as follows a Do you want to install or remove printing i r q q gt j b Do you wish to change the printer description file etc printcap y n n gt y c Enter information for remote printers or local printers accepting remote printing requests Please enter the printer name q to quit gt printer 1 You can enter a printer name you like in this option d Is xxxx a remote printer or a local printer r l gt r e Please ente
28. ed in a standard database called Management Information Base MIB that is stored on the networking device called SNMP agent The print server s SNMP implementation runs in a TCP IP environment A host on the network running Network Management System NMS software can access the print server device by reading and writing the MIB objects stored in the device The Network Management Systems are available from many third party vendors such as Hewlett Packard s OpenView When accessing traversing MIB objects in the print server using NMS software called SNMP manager you need to provide a community name in each SNMP request for authentication purpose The print server supports up to two community names The default community name is public case sensitive with Read Only access right in default When an unusual condition or activity occurs the SNMP agent alerts the SNMP manager through SNMP traps Following list summaries SNMP trap messages that the print server will send out Activities SNMP Trap Messages Description Link Up or Link Down When the network interface on the print server fails a link down trap message is generated if the network interface comes back to life a link up trap message is sent Cold Start or Warm Start When the print server restarts the cold start or warm start trap message is generated Authentication Failure When the print server received a SNMP request with a community name that does not match the community n
29. el port of the printer Check to see if any of the pins on the 36 pin connector 67 are damaged In addition check the cable connection If the pins are damaged contact your dealer for a replacement connector Windows 95 98 Me NT 2000 XP Troubleshooting Multi Segment LAN Environment Installation through the Network Print Port If your print server and Windows 95 98 Me NT 2000 XP are located on two different segments and your Windows NT server is used as the router gateway you will need to implement the following procedures in order for your print server to function properly O Add the RIP for NWLink IPX SPX compatible transport See RIP for NWLink IPX SPX compatible transport Installation Procedure later in this section Add the frame type 802 2 for both Ethernet adapters See Multi Segment Frame Type 802 2 Installation later in this section RIP for NWLink IPX SPX compatible transport Installation Procedure d pt Ole Sy SE From your Windows NT server that is used as a router select Start from the bottom left hand corner of the screen Select Settings Select Control Panel Double click the Network icon Select Services Select Add In the Select Network Service box select the RIP for NWLink IPX SPX compatible transport Click OK Follows the directions on the screen Done Multi Segment Frame Type 802 2 Installation e oh Pee NS From your Windows NT server that is used as a router select Start
30. er 1 OU Tech Installation Procedure E te At your file server console type load install Select NCF files options Select Edit AUTOEXEC NCF file Add or Modify the SET BINDERY CONTEXT line to include the NDS organization O and all organization unit OU objects where users are located For example SET BINDERY CONTEXT O ABC OU SALES OU ABC USA O ABC OU TECH OU ABC USA O ABC When done save the new AUTOEXEC NCF file Please restart your NetWare file server in order for new settings to take effect immediately Next please refer to Auto Setup section in this chapter to finish installing your print server Log into your NetWare file server as a Supervisor Admin or equivalent via a Bindery connection Run NetWare s PCONSOLE and add users to the Queue Users list From your NetWare client computer such as Windows 95 98 Me create a printer that is connected redirected to the NetWare print queue serviced by the print server 41 Note Please refer to NetWare s Print Server Services manuals for detailed PCONSOLE commands SNMP Setup TCP IP networks use a standard management protocol called Simple Network Management Protocol SNMP SNMP is widely used in the industry as a solution for remote network management and monitoring of networking devices SNMP actually includes a protocol a database structure specification and a set of database objects The database objects are contain
31. er and P related settings say IP address subnet mask and gateway IP b Log in root c Assign Print Server an IP address At shell mode c 1 arp s lt the IP address you want to assign to the Print Server gt lt Print Server s Node ID gt c 2 Execute tftp lt Print Server s IP gt get config txt and quit tftp c 3 Edit the config txt and modify the IP address subnet mask and gateway IP When done save the config txt c 4 Execute tftp lt Print Server s IP gt put config txt and quit tftp d Start X windows by typing startx at the shell mode e Open Printer Configuration 59 Printer configuration baghdad EECH S Action Test Help Ge EN amp New Edit Delete Default Apply f Click New button ca Add a new print queue Add a new print queue On the following screens you will be asked to provide basic information for adding a new print queue You will be able to edit the more advanced options afterwards Nothing will be done to your settings until you hit Apply on the last screen g Click Forward button 60 Ki Add a new print queue Queue name Please enter a name for this queue Choose a short name that begins with a letter and contains no spaces About If you like you can enter a description of the printer to help you identify it more easily Short description HPLaserJet2200 h In the Name field type a user defined name click Forward Ki Add a new print que
32. etup dialogue box Solution Specify a new print server name or queue name in the Auto Setup Question G The setup Wizard cant find print server Possible Explanation The Personal Firewall installed in your computer blocks the connection Solution Please disable the Personal Firewall or adjust the security level to lower 76 Additional Installation Instructions Panasonic KX P6100 6300 6500 If you are using a Panasonic KX P6100 6300 6500 laser printer with the print server through the Network Print Port under Windows 95 98 please redirect the printer named Panasonic KX P6100 PCL or Panasonic KX P6300 PCL or Panasonic KX P6500 PCL to the print server through the Network Print Port DO NOT redirect the printer named Panasonic KX P6100 GDI Panasonic KX P6300 GDI or Panasonic KX P6500 GDI to the print server 77
33. f print server by press the reset button Please turn off the power and then hold the reset button and turn on until the status LED blinking rapidly Now the default value is restored 74 Frequently Asked Questions Question A Print jobs are sent to the print queue successfully but fail to be sent to the printer Possible explanations 1 The Print server Name Print Queue configuration in PCONSOLE is incorrect 2 The Print server name specified and stored in the print server memory doesn t match the same one set in PCONSOLE 3 The network cable or power adapter connected to the print server is loose or disconnected 4 The printer is off line jammed or out of paper Solutions Check all the information in PCONSOLE Check all the information of the print server by running PSAdmin Check to see that if the network cabling and power adapter are properly connected Recheck the print server connection by running the PSAdmin It should read Connected oe eg Question B Print jobs start printing but print very slowly or print unknown characters Possible explanation and solution A printer driver is missing or is incompatible with that printer Using a print driver that is not specific for the printer can cause printing errors Install the proper printer driver If these printer drivers are not available to you please contact your printer manufacturer Question C The upgrading process indication bar stops and does
34. from any print server Wireless Operation Mode This option allows you to view the current wireless operation mode of your print server 30 Printer Status 1 Click Status it then appears the sub menu 2 Click Printer it then as shown in the following picture 1P_PrintServ535A07 This page displays the information of the printer which is currently connected to the print server Note If your printer does not support bi directional function some information may not be correctly displayed Printer Information Manufacturer Model Number Printing Languages Supported Current Status Off Line Manufacturer This option allows you to view manufacturer of the printer When the printer connected with the print server it will be show in the manufacture box Model Number This option allows you to view model of the printer When the printer connected with the print server it will be show in the model box Printing Language Supported This option allows you to view command to set the printer When the printer connected with the print server it will be show in the command box Current Status This option allows you to view status of the printer When the printer connected with the print server it will be show in the status box For Example Waiting for job It is means the printer already to printing Wireless Status 1 Click Status it then appears the sub menu 2 Click Wireless it then as shown in the followi
35. ined from the DHCP server or manually specified The option also allows you to manually specify the IP address of the gateway to the print server if DHCP option is disabled This value is optional 20 Upgrade Upgrade allows the user to upgrade the print server device In order to upgrade the unit please perform the steps as follows 1 Click Upgrade button just like a picture B as shown as follow picture Upgrade the print server now or download the newest version PSAdmin and print server s firmware from the internet Upgrade Wizard Upgrade t print server s firmware Next M X Cancel 2 Select General Upgrade Make sure that the upgrade file is located in the same directory as PSAdmin Reset 1 Click Reset button just like a picture lt 2 Reset allows the user to reset the print server device in order to establish a new connection or for new settings to take effect Refresh 1 Click Reset button just like a picture El 2 Refresh searches the network for all attached print server s 21 Note Configure the print speed in the Advanced label must match the printer s speed which connect to the print server Undependable configuration will cause printer to abnormal printing Multiple Print Queues Configuration To configure the print server to service multiple print queues please follow the instructions listed below Log into your NetWare file server as a Supervisor Ad
36. ion Type the IP address of the print Remota Printer field type a name for the print server s print port For example Port1 When done click OK button Now run Printer Manager and you ll see an icon for the printer that is connected to the print server device 63 8 Upgrading Print Server Overview Upgrading print server will allow you to replace its firmware inside the print server while the newer software version of the print server is available from your local dealer Depending on the different systems users might use this chapter is divided into several Sections please refer to the following list for your systems 1 Upgrading the print server from PSAdmin 2 Upgrading the print server from Windows NT 2000 XP 3 Upgrading the print server from UNIX system Note 1 Before you proceed to upgrade the print server please ensure that the necessary binary file is located in your current working directory 2 Before upgrading print server please ensure print server is not printing jobs In case of printing you have to wait till the current print job is finished before you can proceed Upgrading the print server from PSAdmin 1 Log into your NetWare file server as a Supervisor Admin or equivalent 2 Ensure binary file is located in the PSAdmin directory 3 Run PSAdmin from your Windows PC 4 Click the Upgrade icon in tool bar Upgrading the print server from Windows NT 2000 XP Through TCP IP 1 Ensure binary file
37. isk If your printer is not listed consult your printer documentation for a compatible printer Manufacturers Printers HP LaserJet 5L Epson Fujitsu HP LaserJet 5P GCC HP LaserJet SMP Generic HP LaserJet 5P 5MP PostScript al Gestetner HP LaserJet 55i HP HP LaserJet 5Si Mopier IPA TT tm cartas Eci Moniar BS h Have Disk lt Back Cancel 25 9 If you want your Windows based programs to use this printer as the default printer please select Yes and Click Next It will appear as follow picture Add Printer Wizard Default Printer Your computer will always send documents to the default printer unless you specify otherwise Do you want your Windows based programs to use this printer as the default printer 13 Click Finish button 14 Done HP Web JetAdmin Overview HP Web JetAdmin allows you to use a Web browse to revise view manage and diagnose devices connected to the print server or any standard printer MIB devices For more information about a procedure or Windows in the HP Web JetAdmin software see about HP s relation document System Requirements HP Web JetAdmin software runs on Microsoft Windows NT HP UX Solaris Red Hat Linux and SuSE Linux system For information on supported operating systems and browser versions we recommend IE or Netscape version 4 or higher Please access HP Customer Care Online at http www hp com go webjetadmin 26 Note
38. ive 2 Run the setup exe from Windows 95 98 Me NT 2000 XP 2003 The Network Print Monitor for Windows welcome message then appears Choose Setup Wizard or Manual Installation Setup Wizard Welcome to the Network Print Server CD ROM Manual Installation Browser Select one of the options to continue Documentation Exit 3 Choose Setup Wizard the program will auto install the Network Print Monitor PSAdmin and Setup Wizard into your computer The default installation directory will be C Program files Network Print Monitor 4 After installation completes the Setup Wizard message appears 10 Select a Wizard to start setting up your network print server 5 Click Wireless Setup Wizard and the following message appears Wireless Setup Wizard Welcome to the Wireless Print Server Setup Wizard This Wizard will help you configure the wireless network print server to communicate with your wireless network Yelcome Before you continue Select A Print Server 1 Make sure the print server and the printer are properly connected and turned on Configure Wireless 2 Make sure you have the wireless settings of the wireless network S ettings such as the SSID encryption information etc Configure cr Settings To continue click Next ii Save D E wer 0 94 08 11 6 7 Click NEXT the wizard will automatically discover the wireless print server Wire
39. less Setup Wizard Welcome Select A Print Server Configure V ireless Settin Configure TC Setting Save Settin Compi Select A Print Server This Wizard has found the following wireless network print servers on the network Select a wireless network print server that you want to set up from the list Detected print servers on your local network Device Name_____ MAC Address Mode OP ESSID Lcba 1P_PrintServS35414 00 40 01 53 54 14 Infrastructure gt Refresh If the print server you want to set up is not displayed check the connection and click Refresh Note If your print server has just been turned on it may take a few minutes for the print server to initialize and communicate with the wireless network before it can be detected and displayed by the Wizard BACK NEXT gt EXIT Select the print server which you want to configure and press NEXT Wee Select A Print Server Configure Wireless Settings Configure TCPH Settin Save Settin Wireless Setup Wizard Change Wireless Settings In the following steps this Wizard allows you to configure some basic wireless settings of the print server If you are not familiar vith these settings do not change them Wrong settings may cause the print server not to function properly Ze Yes I want to change settings Password C No dont want to change settings To change settings y
40. llowing picture The last 6 digits of the Node ID located on the back of the print server unit Select one of the print server s ports from the list Uninstalling Network Print Port on Windows 95 98 Me NT 2000 XP To provide users an easiest way to remove all of the Network Print Port components from Windows 95 98 Me the Network Print Port software comes with un installation wizard program to help users remove the software components from their Windows 95 98 Me NT 2000 XP systems in minutes Please follow the directions listed below to proceed with the un installation procedure After the Network Print Port is removed the print server is no longer accessible via the Network Print Port You have to re install the Network Print Port on your system in order to access the print server again Procedure 50 Click Start point to Settings and select Control Panel Double click the Add Remove Programs icon Click Add Remove tab Select Network Print Monitor for Windows 95 98 Me and click Add Remove button The un installation wizard program will be launched NAPA ES Follow the directions on the screen to complete the un installation procedure Note We recommend you restart your computer after un installation is finished 7 TCP IP LPR Port Printing Installation Basic TCP IP Installation Overview When installing your print server in a TCP IP environment IP addresses are essential as a basic means of communications It is theref
41. min or equivalent Run the PSAdmin from your Windows Select the print server and to be configured Click the Wizard icon in the tool bar Type in a Print server and a Print Queue Name For more detailed information about Wizard please refer to the Wizard section in this chapter Run the NetWare s PCONSOLE and create additional print queues Select the Print server name you specify in Step 5 Select the Print server Configuration option and select the Queue Serviced by Printer option For NetWare 4 x s PCONSOLE please select Printers option and select Printer 0 instead 9 Select the Printer 0 and press the nserf key to add the print queues you create in Step 6 into the list For NetWare 4 x s PCONSOLE please select Print queues assigned option instead 10 Reset the print server by clicking the Reset icon from the PSAdmin Done Oe es Pr Note Please refer to NetWare s Print server Services manuals for detailed PCONSOLE commands Uninstalling the PSAdmin on Windows PC To help users easily remove all installed software components of the PSAdmin from their Windows PC and the PSAdmin software comes with un installation wizard program that can automatically remove the software components from their Windows PC systems in minutes Please follow the directions listed below to proceed with the un installation procedure After the PSAdmin is removed the print ser
42. n use Site Survey to help you assign a SSID or input in manually Channel Specify a Channel number that meet your enviromemt Data Transmit Rates Choose the transmit rate of your wireless print server WEP Settings USE WEP Disabled or Enabled Key Format Alphanumeric or Hexadecimal WEP key Input your WEP key in this field Printer Setup parallel print server only 1 Click Setup it then appears the sub menu 2 Click Printer it then as shown in the following picture 2 1P_PrintServ535B13 Y This setup page allows you to enable or disable the bi directional function of the printer port Bi directional Settings Printer Port Auto Detect DI Bi directional This option allows you to select the bi directional of the print server There are two ways to select this option includes Disable or Auto Detect 38 TCP IP Status 1 Click Setup it then appears the sub menu 2 Click TCP IP it then as shown in the following picture 27 1P_PrintServ535A07 Lok Status Misc O This setup page allows you to configure TCP IP settings of the print server TCP IP Settings Ze Obtain TCP IP settings automatically use DHCP BOOTP C Use the following TCP IP settings IP Address fi92 168 1 1 94 Subnet Mask 255 255 255 0 Gateway s IP f192 168 1 1 ave e DHCP BOOTP This option allows you to select DHCP BOOTP option If there is a DHCP BOOTP server on your network This option allows the p
43. ng picture 31 SS 1P_PrintServ535A07 th Setup Misc O This page displays the current wireless settings and the status of the print server Mode Infrastructure AP s MAC Address 00 02 6F 03 47 B5S SSID Channel Number 1 Data Transmit Rate 1 2 5 5 11 Mbps WEP Encryption Disabled Mode This option shows the wireless operation mode of your print server AP s MAC Address This option shows the MAC address your wireless AP SSID The ESSID of your wireless network Channel Number Current channel number Data Transmit Rate Current transmit rate WEP Encryption The status of WEP encryption TCP IP Status 1 Click Status it then appears the sub menu 2 Click TCP IP it then as shown in the following picture 1P_PrintServ535A07 e Y This page displays the current TCP IP settings of the print server TCP IP Settings Use DHCP BOOTP ON IP Address 192 168 1 194 Subnet Mask 255 255 255 0 Gateway s IP 192 168 1 1 32 Use DHCP BOOTP This option allows you to view DHCP BOOTP status If there is a DHCP BOOTP server on your network this option allows the print server to obtain IP related settings automatically from your DHCP server IP Address This option allows you to view IP address from the print server The IP address must meet the IP addressing requirements of the network segment Subnet Mask This option allows you to view subnet mask from the print server The IP address must
44. nter Name or IP Address fi 92 168 10 200 m Protocol C Raw Ge LPR Raw Settings Port Number E DO LPR Settings Queue Name g LPR Byte Counting Enabled J SNMP Status Enabled Community Name public SNMP Device Index fi Cancel Note Please DO NOT type any other name than Ip1 in this step 10 11 12 13 Click Finish Select the appropriate printer manufacturer and printer type list and click Next Type in a new Printer name or leave it in default and click Next button A message reading To confirm that the printer is installed properly you can print a test page Select Yes Recommended and click Finish Done 55 UNIX Installation After the IP address is assigned the Print Server is ready to be configured For some popular UNIX systems SCO OpenServer and UnixWare Sun Solaris IBM AIX and Linux we include the detailed installation procedures below If you can t find the installation procedure corresponding to your UNIX system please refer to your UNIX manuals for details about configuring your UNIX for the remote printing system SCO UNIX OpenServer 5 0 x 1 Login root 2 Type arp s lt IP address gt Print server s node ID gt The Print servers node ID can be found from the white label on the backside of the Print Server For example arp S 192 72 214 103 00 40 01 05 01 8c 3 Type ping lt Print server s IP address gt For exampl
45. nter Port Computers communicate with printers through ports Select the port you want your printer to use If the port is not listed you can create a new port C Use the following port DEI Printer Port HP LaserJet 5 LPT2 Printer Port LPT3 Printer Port COM1 Serial Port COM2 Serial Port FAM Serial Part Y Note Most computers use the LPT1 port to communicate with a local printer Local Port y Local Port Network Print Port Standard TCP IP Port lt a e Create a new port Type 5 The Add Standard TCP IP Printer Port Wizard box will then appear as shown the picture as below and type in the IP address assigned to the print server in the Printer Name or IP Address box Click Next 53 Add Standard TCP IP Printer Port Wizard Add Port For which device do you want to add a port 192 168 10 200 IP_192 168 10 200 6 Inthe Add Standard TCP IP Printer Port Wizard box as shown in the following picture Select Custom Click Settings button and click Next Add Standard TCP IP Printer Port Wizard Additional Port Information Required The device could not be identified 7 Inthe Configure Standard TCP IP Port Monitor box as shown in the following picture select LPR form Protocol type in a queue name for example oi 8 Click OK and Next 54 Configure Standard TCP IP Port Monitor 2 x Port Settings Port Name IP 92 168 10 200 Pri
46. ocation name of the print server To confirm the print server s location name where the print server is located in the office s LAN Password This option allows you to input setup password of the print server When you select setup menu of web configuration from the print server it then as shown in the following picture Re type Password Je Please type your user name and password Site 192 168 10 201 Realm PinSerwr User Name Password I Save this password in pour password list Cance e User Name You must be input the default administration user name admin as login user name e Password The default password is empty After setup password is completed from the print server you should to remember this password to input password box Wireless Setup 1 Click Setup it then appears the sub menu 2 Click Wireless it then as shown in the following picture This setup page allows you to configure wireless settings of the print server By default this print server acts as a wireless station in the Infrastructure mode Basic Settings Mode Infrastructure gt Select SSID or Manaully Enter SSID Below Site Survey Channel a USA 1 11 Data Transmit Rates Auto Advanced Use WEP Disabled Key Format Alphanumeric WEP Key Help ave Star 37 Basic Settings Mode Infrastructure Ad hoc or 802 11b Ad Hoc Select SSID or Manually Enter SSID Below You ca
47. om the Printer Ports box as shown in the following picture select the LPR Port Printer Ports 27x Available Printer Ports Local Port New Monitor on The Add LPR compatible printers box will then appear as shown in the following picture Type in the IP address assigned to the print server in the Name or address of server providing Ipd box Add LPR compatible printer E Name or address of server providing Ipd fi 92 72 214 69 Name of printer or print queue on that server Je BECH _t In the Name of printer or print queue on that server box type in a printer name for example Ip1 Click OK In the Printer Ports box select Close Click Next 10 Select the appropriate printer manufacturer and printer type list and click Next 52 11 Select Shared Type in a new Share Name or leave it in default and click Next 12 A message reading After your printer is installed Windows can print a test page so you can confirm that the printer is set up properly Select Yes Recommended and click Finish 13 Done Windows 2000 XP Standard TCP IP Port Printing Installation 1 Click Start point to Settings and select Printer 2 Run Add Printer Click Next 3 The Add Printer Wizard screen will appear Select Local Printer and click Next 4 From the type of Create a new port box as shown in the following picture select the Standard TCP IP Port Click Next and Next Add Printer Wizard Select the Pri
48. or 1 2Mbps 5 5Mbps or 11Mbps Click NEXT Choose Enable the WEP Encryption as you need and click NEXT 13 Wireless Setup Wizard Security and WEP Encryption Settings Configure the following security settings on the print server These settings must match your wireless network for the network print server to communicate with all computers over a wireless connection _ Enable WEP Encryption Type E 54 bit C 426 bit Select A Printo E Key Format ZS Aiphanumeric Hexadecimal Configure Wireless Encryption Key I Settings 1 For 64 bit sometimes called 40 bit VVEP encryption enter the key which contains 5 alphanumeric character or 10 hexadecimal digits depending on Configure TC the key format you select Settin 2 2 For 125 bit WEP encryption enter the key which contains 13 alphanumeric characters or 26 hexadecimal digits depending on the key format you Save Settin select An alphanumeric character is a through z 4 through Z and O through 9 A hexadecimal digit is O through 9 and A through F If your wireless network uses WWEP encryption to secure all data communications you must enable WEP encryption setting and enter a key for the print server lt BACK NEXT EXIT 10 Specify a fixed IP address or use dynamic IP address then click NEXT TCP IP Settings Specify TCPAP settings for the print server The print server can be set up either to obtain IP address from a DHCP ser
49. ore necessary to first assign an IP address to your print server unit After assigning an IP address the print server can be configured accordingly Assigning an IP Address The first step to install a print server on a TCP IP network is to assign the print server an IP address and other related TCP IP settings before the print server can function You can select the following two methods to specify an IP address the print server Each method will be detailed in the following section 1 Use the Network Print Monitor utility 2 Manually specify using DOS commands or UNIX text mode commands This applies to Windows NT 2000 XP and UNIX systems Note The Network Print Monitor can only search for the print server s over the same network segment the Windows NT 2000 XP UNIX computer is located You would like to install a print server on a different network segment DHCP The print server supports DHCP feature allowing the print server to obtain an IP address and related TCP IP settings automatically from a DHCP server While the print server supports 51 DHCP we strongly recommend you manually specify a fixed IP address to the print server By default the print server s DHCP function is disabled Windows NT LPR Port Printing Installation ils 2 8 9 Click Start point to Settings and select Printer Run Add Printer The Add Printer Wizard screen will appear Select My Computer and click Next Click Add Port Fr
50. ost name and its associated IP address Note Before this step please make sure you have follow the directions on page 80 to manually assign an IP address to the Print Server 3 Under the prompt sign type smit and press Enter 58 Select Device Select Printer Plotter Select Printer Spooling Select Add a Print Queue Select Remote Select Standard Process 10 In the Queue Name option type in a printer name For example printer 1 11 In the Host Name option type in the IP address of the Print Server ONO Ol Note You can add the host name associated with the IP address in the etc hosts file If you have done this please use the host name instead of the IP address 12 n the Name of Queue on Remote Server option type in a print queue name For example printer 1 q 13 Done Redhat Linux 9 The Print Server can work under any Linux based systems including Slackware RedHat etc without any problems Basically the Linux s printing system is based on BSD system Although many commercial Linux systems are available in the market and their commands will vary slightly depending upon which version is used the functionality of the Linux based variants is exactly the same Following are the outlined procedures recommended for all users on Red Hat Linux 7 2 7 3 or later with X Window system installed a Make sure that the TCP IP is well configured on your RedHat system including network interface card s driv
51. ou may have to enter a password A brand new network print server has no any pas word lt BACK NEXT gt EXIT 12 8 Select YES if you want to change the configuration and press NEXT then the picture appears Wireless Setup Wizard Basic Wireless Settings Configure the following wireless settings on the print server These settings must match your wireless netweork for the print server to communicate vvith all computers over a wireless connection Welcome Communication Type infrastructure Select A Print Server SSID any gt s S Channel Number Jo Configure Wireless Settings Data Transmit Rates Auto Configure TCPAP Settin 1 Jn Infrastructure Access Point mode the wireless network print server 4 vill communicate with netvvork computers through an Access Point Save Settin 24n Ad Hoc or 602 11b Ad Hoc mode wireless devices communicate with each other directly Complete to enter the Channel number used by the Access Point E the communication type is Infrastructure Access Point you do not have BACK NEXT EXIT Communication Type please choose Infrastructure Ad hoc or 802 11b Ad hoc that meet your network environment SSID Input the proper SSID of your wireless network The default value is lt any gt and it will connect with the AP which has the best signal in your wireless network Channel optional Data Transmit Rates Auto
52. ou should prepare m One Win98 Me 2000 XP 2003 PC with CD ROM One 802 11b Access Point and Wireless Adapter H One Printer USB or Parallel Port Hardware Installation To install the print servers you need to complete these steps e Confirm that your printer parallel USB port work well e Connect the print server to the network and printer s and plug in the print server e Create a configuration page from the print server Follow these instructions to install the print servers please refer to any peripheral you are connecting to the print server 1 To ensure your printer s work well do one of the following e Send data through the parallel USB port of each printer you are connecting to the print server or generate a printer self test page 2 Turn off the power for each printer 3 Connect the print server to printer s Note One port print server attaching only one printer further three ports print server can expand three printers for example the print server s port1 should be connect printer1 port2 or port3 as following above step 4 Plug the AC power adapter into the power receptacle in the side of the print server 5 Plug the AC power module into the wall out let the print server is switched on after you plug it in 6 Check the LED s marked as status on topside or beside of the print server It should be flash five times normally if not please contact your local dealer for repair or replacement
53. print server 29 System Status 1 Click Status it then appears the sub menu 2 Click System it then as shown in the following picture Address Je http 192 168 1 194 5YSTEM HTM Go 1P_PrintServ535A07 La Y This page displays the general system information of the print server System Information Device Name System Contact System Location System Up Time Firmware Version Wireless MAC Address Wireless Operation Mode 1P_PrintServ535407 0 12 17 6 08 21E 2003 03 31 11 56 35 00 40 01 53 54 07 Normal Device Name This option allows you to view device name of the print server To correct the print server s device name System Contact This option allows you to view contact name of the print server To check the print server s contact name who in charge of this device System Location This option allows you to view Location name of the print server To confirm the print server s location name where the print server is located in the office s LAN System Uptime This option allows you to view uptime of the print server When you start the print server it will compute the print server from start time to power off time Firmware Version This option allows you to view firmware version of the print server To verify the print server s firmware version is newer in this time Wireless MAC Address This option allows you to view Node ID of the print server The Node ID is unique
54. r name which configured by PSAdmin utility or PCOMSOLE program Polling Time The time interval in which the print server unit polls the file server for servicing of print queues Logon Password This option allows you to input encrypted password from the print server The print server login to NetWare server that administrator set password from selected print server NDS Mode To Enable NDS Mode if you want to setup NDS environment To select Tree Name of NetWare then input context name in the Context box Bindery Mode To Enable Bindery Mode if you want to setup Bindery environment To select File Server Name of NetWare 40 Installing Print Server on NetWare 4 x 5 x Due to its architecture and functionality the print server must work under NetWare 4 x 5 x NDS Bindery Emulation When you install the NetWare file server for the first time by default the installation program will automatically set up the Bindery Emulation function for you by adding SET BINDERY CONTEXT in the AUTOEXEC NCF file By default the bindery context will only be set on your organization O object If you have ever modified this line or if you have ever added any organization units OU to your NDS tree after the NetWare system was installed please read the following section before you install the print server For the purpose of illustration we assume the NDS tress structure is as follows ROOT O ABC OU ABC USA OU Sales Admin FileServ
55. r other setting s Next recreate the necessary parameters or reconfigure the print server by running the PSAdmin TCP IP Troubleshooting When you are configuring a new print server on your NT UNIX server through LPR Port printing under TCP IP protocol you might encounter the following problem in your initial installation steps I can do the arp command However when am going to ping or tftp the print server it always shows Request timed out have checked the print server s power and it exactly passed the POST Besides the network cabling is OK As such can t do tftp command to get and put the print server s configuration file and save its IP address permanently can t therefore continue installing the print server Regarding this problem there are three possible causes A The print server s Node ID you specified in the arp command is not correct If this is the case please ensure the Node ID field in the corresponding entry of the print server s IP address in NT s ARP cache table is correct by typing the following command at NT s DOS prompt arp a If the Node ID shown on the screen doesn t match the print server s Node ID please follow the instructions below to reset the entry 1 At NT s DOS prompt type arp d lt print server s IP address gt to delete the current entry 2 Type arp s lt print server s IP gt lt print server s Node ID gt to specify a new ARP entry 3 Refer to Chapter 7 for the de
56. r the name of the remote host that xxxx is attached to gt the Print server s IP address you specified in Step 2 for example 192 72 214 103 Note You can add the host name associated with the IP address in the etc hosts file If you have done this please use the host name instead of the IP address f Printer xxxx is connected to host 192 72 214 103 Is this correct y n gt y g After it shows some messages it will ask you a question If you re not sure answer nm y n n gt n h Would you like this to be the system default printer y n n gt answer this question if you like to make it as a default printer i Do you want to install or remove printing i r q q gt q j Do you want to star remote daemon now y n gt y 11 Done Submit print jobs by using Ip or Ipr command For example lp d printer 1 etc printcap SUN Solaris 2 x 1 Login root 2 Type arp s lt IP address gt lt Print server s node ID gt The node ID can be found from the white label on the backside of the Print Server For example arp S 192 72 214 103 00 40 01 05 01 8c 3 Type ping lt Print server s IP address gt For example ping 192 72 214 103 You should get the responses from the Print Server 57 4 Type tftp lt Print server s IP address gt For example tftp 192 72 214 103 At the tftp prompt type get config txt to get
57. rd Click Next 4 Select Network printer option and then click Next 5 Select Connect to a printer on the Internet or on your intranet option appear as follow picture 24 Add Printer Wizard Locate Your Printer How do you want to locate your printer If you don t know the name of the printer you can browse for one on the network What do you want to do Type the printer name or click Next to browse for a printer Name fre Ze Connect to a printer on the Internet or on your intranet URL ESA 92 168 10 182AIp1 lt Back Cancel 6 In URL s box input print server s IP address for example http 192 168 10 182 lp1 Then Click Next One port should be the port name as Ip1 Three ports should be the port name as Ip1 Ip2 and Ip3 7 It will check print server to connect to HP printer if not it will appear as follow picture Then Click OK Connect to Printer x The server on which the DESKJET 810C printer resides does not have the correct printer driver installed IF you want to install the driver on your local computer click OK 8 Select the appropriate printer manufacturer and printer type and click Next appear as follow picture Add Printer Wizard Add Printer Wizard The manufacturer and model determine which printer to use ke Select the manufacturer and model of your printer If your printer came with an installation disk click Have D
58. rint server to obtain IP related settings automatically from your DHCP server IP Address This option allows you to input IP address from the print server The IP address must meet the IP addressing requirements of the network segment Subnet Mask This option allows you to input subnet mask from the print server The IP address must meet the IP addressing requirements of the network segment Gateway This option allows you to input gateway from the print server This IP address of gateway must meet the router or gateway to go across of the network segment NetWare Setup 1 Log into your NetWare file server as a Supervisor Admin or equivalent 2 Select NetWare and type in the Print server that created during PCONSOLE Select the NetWare File Server to which the print server device will be attached 3 Click Setup it then appears the sub menu 4 Click NetWare it then as shown in the following picture 39 This setup page allows you to configure the NetWare function of the print server General Settings Printer Server Name DEFAULT_PS_NAME Polling Time 3 seconds min 3 max 29 seconds Logon Password NetWare NDS Settings Use NDS Mode Disable D 8 v Name of the NDS Tree Name of the NDS Context NetWare Bindery Settings Use Bindery Mode Disable Name of the File Server File Server not found ave esta Print Server Name This option allows you to input print serve
59. rt HP WebJetAdmin This option allows user determine to disable enable the Support HP WebJetAdmin SNMP Traps Enable the function of sending SNMP Authentication Failure trap message to the network administrator if the community name within a SNMP request is not correct AppleTalk Setup The print server can print jobs submitted from Macintosh workstations connected to an Ethernet using AppleTalk protocol The basic configuration is for the print server in an AppleTalk environment is performed simply by opening the Chooser window and selecting a printer that is connected to the print server 1 Click Setup it appears the sub menu 2 Click AppleTalk it as shown in the following picture 1P_PrintServ535A07 This setup page allows you to configure AppleTalk settings of the print server AppleTalk Settings AppleTalk Zone Name Port Name ATALK_PS Printer Configuration Printer Type Laserwriter Data Format TBCP DI 3 Zone Name In this option type an AppleTalk Zone name that you want the print server to belong to or leave it in default This enables the print server automatically search and link itself to the default zone that is set on the Apple Talk router if found We also assume that at least an AppleTalk Zone exists on the network If no any zone exists the print server itself displays the zone name as an asterisk in the current AppleTalk Status of the print server in the web browser 44 4 Port
60. sccccccececessssecccccecececsssssecaccecececesssssntececseceecesssstacceeseeens 26 INSTALLING HP WEB JETADMIN cccccccccececesesseccccccececsssssssaccecececscessssecacescceeessssntnceceseceecneneas 27 REMOVING HP WEB JETADMIN Urs 28 5 CONFIGURATION FROM EMBEDDED WEB SERVER ccccsssssssscssssssssscsssscseseees 29 OVERVIEW 2 82 20 tete ORI ONG ata do SALES E EE 29 USING EMBEDDED WEB GERBER 29 SETUPIMEN keeten clas te sa tate bs ale re Bed Seah o tat eaters ts 36 INSTALLING PRINT SERVER ON NETWARE A vibx 41 SETTING UP A MACINTOSH COMPUTER 45 6 NETWORK PRINT MONITOR cccsssccccossssssscssscccccsssscsscsssscccscssscscossssccccssssssssscsscsscessees 46 PREPARA TION att oreo pie ein sree oie oa ota on E E ae iO o 46 TCP IP PROTOCOL INSTIALLATION ts tssssterro re essssesrre rees 47 IPX SPX COMPATIBLE PROTOCOL INSTALLATION 0ocococonononononononononononononononononononono nono nononononononononos 47 NETBEUI PROTOCOL INSTALLATION ssssssssessssssseseeesssssserereretssssrsrtoretsessssettetstssssesrrensessssesrre reese 48 WIN 95 98 ME NT 2000 XP INSTALLATION HBROCEDURE 48 UNINSTALLING NETWORK PRINT PORT ON WINDOWS 95 98 ME NT 2000 XP ccceceeeeeees 50 7 TCP IP LPR PORT PRINTING INSTALLATION o oocccccccccocoononconoccnccoconocononoconococonocooonanonocococos 51 BASIC TCP IP INSTALLATION OVERVIEW ccccccccesecececececececececececeeececeseceeececeeecececececeeececececeeeees 51 ASSIGNING
61. server by using Wizard TCP IP Wizard 1 Click Wizard button just like a picture A and select TCP IP Wizard 16 Configuration Wizard p Description TCPAP WWizard can assist you in setting up the necessary parameters for TCPAP printing Next M gt lt Cancel Select Obtain an IP address from DHCP server If there is a DHCP server on your network This option allows the print server to obtain IP related settings automatically from your DHCP server This setting by default is disabled If you would like to manually specify an IP address to the device please skip to the following step In the IP Address option type an IP address for the print server The IP address must meet the IP addressing requirements of the network segment TCP IP Wizard X TCPAP Wizard E An IP address can be automatically assigned to the print server by a DHCP server If your network does Configuration not have a DHCP server please specify an IP Wizard address for the print server Obtain an IP address from a DHCP server IP Address 192 168 10 149 Subnet Mask 255 255 255 0 Gateway 192 _ 168 _ 10 0 Back af OK gt Cancel Optional In the Subnet Mask option type the Subnet Mask your LAN or network segment is currently configured to use Optional In the Gateway field type the IP address of gateway When done click OK button
62. t server NetWare 3 12 network 4 x 5 x Embedded Web server Windows Remote setup Follow standard browse for example IE or 95 98 Me print server from Netscape Windows private LAN as NT 2000 XP 2003 soon NetWare 3 12 4 x 5 x HP Web JetAdmin Windows Remote Print server solution for continual management of NT 2000 XP 2003 management of multiple printers anywhere on your LAN NetWare 3 12 print server 4 x 5 X include alert and consumables Internet Printing Protocol Windows 98 SE Printing via the Allows saving distribution of HQ hardcopy Windows internet to document over Internet replacing fax mail 2000 XP Internet Printing Protocol enabled print server Comment Configuration solution Table has many installations way to setup Windows 95 98 Me Windows NT 2000 XP 2003 NetWare UNIX Linux system and Mac computer Firstly we introduce PSAdmin utility HP Web JetAdmin program and Internet Printing Protocol solution Then we will discusse Embedded Web Server Installation with print server 3 The PSAdmin Utility for Windows based The PSAdmin is a proprietary Windows based management program that can assist you in configuring and managing your print server in NetWare environments The program can be run from any Windows PC Installing the PSAdmin To install PSAdmin please follow the directions listed below 1 Insert the Setup CD into your CD ROM dr
63. tAdmin software from your web server use the uninstall program provided with the software package 28 5 Configuration from Embedded Web Server Overview The Print Server contains an embedded web server that can be accessed through a supported web browser on a LAN for example IE 4 0 Netscape 4 0 or above is recommended The embedded web server provides access to configuration and management pages for the print server and the connected peripheral device Using Embedded Web Server Before you can use the embedded web server the print server must be configured with an IP address There are many ways to configure the print server s IP address For example the Windows based of PSAdmin utility can easily set an IP address with the print server please see the Properties TCP IP options of chapter 3 After an IP address is established on the print server perform the following step Status Menu Once you have finished the IP address configuration with print server You should be use web browser to view and management the print server The status menu of the print server helps administrator control the print server s System Printer NetWare TCP IP SNMP and AppleTalk of status for the time being Preparation Enter the IP address of the print server as the URL for example 192 168 10 132 Then the print server s home page will appear in content of the web browser Please follow this information in the status menu of the
64. tailed instructions to complete the installation 70 B The print server s IP address is duplicated or is as same as another computer s IP address on the network If this is the case please consult your network administrator to obtain an unused IP address for your print server C The print server is on one segment and your Windows NT server is on the other segment This troubleshooting guide will also apply to a multiple segmented network while installing the print server For example assuming the print server is on Segment A NT server is on Segment B and there is a gateway computer between Segment A and Segment B The network might be a complete TCP IP network or a hybrid of TCP IP and IPX SPX network If this is the case you have to adopt the following steps depending on which platform the gateway computer is a lf the gateway computer is a NT UNIX server You have to do the same arp command to specify an entry on the NT UNIX computer as a gateway in order for it to forward your subsequent ping or and tftp commands to the print server b If the gateway computer is a Novell NetWare file server 1 Due to the presence of this NetWare file server the IPX SPX protocol might be used on your network Therefore we strongly suggest you run the PSAdmin from any client computer and select Manual Setup to specify the print server s IP address For more detailed information about Manual Setup please refer to Chapter 3
65. the Print Server s configuration file For example tftp gt get config txt 5 Quit from tftp and then use your editor to modify the 05 BoxlPAddress field in the config txt file from 0 0 0 0 to the IP address you specify in Step 2 6 Optional Modify the 06 Gateway field from 0 0 0 0 to your gateway s IP address 7 Optional Modify the 07 SubnetMask field from 0 0 0 0 to the subnet mask 8 When done save the new config txt 9 Type tftp lt Print server s IP address gt At the tftp prompt type put config txt to save the new configuration file back to the Print Server For example tftp gt put config txt 10 Type Ipsystem tbsd lt Print server s IP address gt For example Ipsystem tbsd 192 72 214 103 Note You can add the host name associated with the IP address in the etc hosts file If you have done this please use the host name instead of the IP address 11 Type Ipadmin pprinter 1 s lt Print server s IP address gt where printer 1 represents the Print Server s parallel port You can enter a printer name you like For example Ipadmin pprinter 1 s192 72 214 103 12 Type accept printer 1 For example accept printer 1 13 Type enable printer 1 For example enable printer 1 14 Submit print jobs by lpr command For example lpr Pprinter 1 etc hosts IBM AIX 4 xx 1 Login root 2 Optional Edit the etc hosts file Add a line of the Print Server s h
66. ue Queue type Select a queue type Networked UNIX LPD z Server Queue 192 168 10 251 Ip1 i Inthe Queue Type field choose Networked UNIX j Inthe Server field type the IP of print server k In the Queue field type a print server s port name which connect to the printer For example Ip1 Click Forward button 61 m In the Printer field choose Postscript Printer iw Add a new print queue Printer model Select the printer manufacturer and model Depending on how the remote queue is configured you may need to select the generic PostScript option here Laserjet 2100M Laserjet 2200 LaserJet 2D Iancarint D n Choose the model of printer and click Forward iw Add a new print queue Finish and create the new print queue About to create the following queue Type Unix Print Queue Queue Ip1 192 168 10 251 Printer HP Laserjet 2200 62 UnixWare 7 10 11 12 13 Login root Run CDE Common Desktop Environment Open the subpanel under the SCO icon in the Front Panel Select SCO Admin Select Print Setup Manager from System Administration window Click LPD icon in the tool bar of Print Setup window In Name field type a name for the printer for identification purpose In Protocol field select Ipd BSD Select your printer s make and model from the Make Model list In Printer Connection Type select On Remote Server It then appears a new Remote System opt
67. ver is no longer accessible via the PSAdmin You have to re install the PSAdmin on your system in order to access the print server again 22 Procedure A UA a Click Start point to Settings and select Control Panel Double click the Add Remove Programs icon Click Change or Remove Programs tab Select Network Print Monitor for Windows 95 98 NT 2000 XP and click Change Remove button The un installation wizard program will be launched Follow the directions on the screen to complete the un installation procedure 23 4 Internet Printer Connection and HP Web JetAdmin IPP Overview Print server s support the Internet Printing Protocol IPP Using the appropriate software on your system you can create an IPP print path from your system as Windows PC over the Internet Note For incoming print path requests the network administrator have to configure the firewall to accept incoming IPP requests Windows NT 2000 XP 2003 For Windows NT 2000 XP 2003 you can use a supported Web Browser for example Netscape or IE to view the embedded web server on the print server Contact your administrator to get the IP address or URL of the printer and browse to the print server s web page For example to install Windows 2000 by IPP service you must follow below information 1 Click Start button 2 Select Settings and then select Printers option 3 Click Add Printer icon Appear welcome to the add printer wiza
68. ver on the network or to use a static IP address Welcome Select A Print Server Obtain an IP address automatically use DHCP Configure wireless 77 Specify an IP address Settin IP address 192 168 1 100 Configure TCP Subnet Mask J 252 255 255 0 Gateway s IP 192514687 4 55 t s highly recommended that you set up the print server to use a static IP address Make sure the IP address is correctly entered for the print server to work properly lt BACK NEXT EXIT 11 In this page you can confirm your setting value again Click NEXT 14 Wireless Setup Wizard 3 a Confirm Settings The Wizard is about to finish the configuration Following is the summary of the settings These settings will be configured on the wireless network print server Wireless Settings Welco me Mode Infrastructure SSID lt ANY Select A Print Server Data Transmit Rates Auto Configure Wireless WEP Disable Settin TCPAP Setti Configure ICH IP Address 192 166 1100 Settin Subnet Mask 255 255 255 0 Gateway s IP 192 168 1 1 Save Settings Compi Werify all information before they are saved Click Next to apply these settings to the wireless network print server BACK NEXT gt EXIT 12 Done Wireless Setup Wizard Installation Complete Your wireless network print server has been successfully configured Welco me E H Hote You may have to run Hetwork
69. work icon If the TCP IP Protocol is not already installed click Add Select Protocol and click Add Select Microsoft from the Manufacturers list Select TCP IP Protocol from the Network Protocols list Specify an IP address Subnet Mask and Gateway address or specific Obtain IP address automatically if a DHCP server is available on the LAN Restart the computer Done Note Using TCP IP protocol to access the print server requires well configured TCP IP settings If you are not familiar with these settings please consult your network administrator for details or ask for help IPX SPX compatible Protocol Installation Sl Click Start point to Settings and select Control Panel Double click the Network icon If the IPX SPX compatible Protocol is not already installed click Add Select Protocol and click Add Select Microsoft from the Manufacturers list Select IPX SPX compatible Protocol from the Network Protocols list and follow the instructions on the screen Restart the computer Done 47 NetBEUI Protocol Installation 1 Click Start point to Settings and select Control Panel 2 Double click the Network icon 3 If the NetBEUI is not already installed click Add 4 Select Protocol and click Add 5 Select Microsoft from the Manufacturers list 6 Select NetBEUI from the Network Protocols box and follow the instructions on the screen 7 Restart your computer for new settings to take effe

Download Pdf Manuals

Related Search

Related Contents

MittelstandsMonitor 2008  Targus THD006CA  Kaspersky Lab Internet Security 2009, 5 User  BDA_PVR_2_100CI  Delta 77135 Installation Guide  Benutzerhandbuch Route 650 - GetFit attrezzi home fitness e cardio  Verbatim External Hard Drive eSATA / USB Combo Drive 1.5TB  THES 932 V2.0 ModuStar    EPSON Safety Instructions Manual  

Copyright © All rights reserved. Failed to retrieve file