Supermicro M28SAB
Contents
1. Hard Drive Tray Latch Figure 4 2 Mobile Rack with Hard Drive Trays Installing Hard Drives into the Mobile Rack 1 Press the release tabs to open the hard drive carrier latch 2 Using the latch as a handle pull the drive carrier from the hard drive Warning Enterprise level hard disk drives are recommended for use in Supermicro chassis and servers For information on recommended HDDs visit the Supermicro Web site at www supermicro com M28SAB Mobile Rack User s Guide Hard Drive Hard Drive Carrier 1L M3 Screws Figure 4 3 Hard Drive and Hard Drive Tray 3 Place a 2 5 hard drive in the hard drive carrier 4 Align the hard drives to the rear of the hard drive tray 5 Secure the hard drive to the tray using four M3 screws as illustrated 6 Using the hard drive tray latch as a handle slide the hard drive into the mobile rack 7 Close the hard drive tray handle to lock the hard drive into place 8 Repeat steps 1 8 for each hard drive that you will install into the mobile rack 4 6 Safety Information and Technical Specifications 4 9 Connect Data and Power Cables Connecting the Cables 1 Connect the SAS cables to the mobile rack A longer SAS cable may be required see the recommended cables listed earlier in this manual 2 Connect the power cables from the chassis power supply A power cable extension may be required 4 10 Advanced Co2. C A Haat A N Agar e E DE R E DESIGNEDINUSA 3 ont BPN SASI28A REV 1 00 Figure 3 2 Front Jumper Explanation of Jumpers 3 2 1 Connector F i Pins nnl To modify the operation of the backplane jumpers can be used to choose between optional SEUMAS Jumpers create snoris between two pins to change the function of Jumper the connector Pin 1 is identified with a square solder pad on the printed circuit board e N Note On two pin jumpers Closed means Setting the jumper is on and Open means the jumper is off the pins General Jumper Settings Jumper Jumper Settings 1 2 Fan enabled oe De eem leise 1 2 Fan enabled dit 2 3 Fan disabled Open 45 C Allows the overheat temperature to be JP25 1 2 50 C adjusted 2 921559 3 3 M28SAB Mobile Rack User s Guide 3 4 Rear Connectors and LED Indicators SAS 0 SAS 1 SAS 2 SAS 3 SAS 4 SAS 5 SAS 6 SAS 7 J1 J2 J3 J4 J5 J6 J7 J8 10 QW VP w hw wi ow v 3 O J O o N Q la ep z zi E c 7S f f TUIA JANG HO p 54 D9 D47 g amp v 4 Nv AD30 ape ABB D32 c AD33 am f A035 D367 AD37 2 AD3B cADIS p c AM ADAC AD43 ADM DIS oc i ue E H E Le j pie Kc KT i s A c c A FAILO 8 ACTO FAILI Cri al ACT2 FAIL3 a ACT3 FAIL4 ACTA FAILS amp ACT5 A ACT6 FAIL7 eic D30 D32 D34 D36 D38 D40 D42 D44 D31 D33 D35 D37 D39 D41 D43 D45 Fig
3. ANUS i ERE 4 1 4 4 Setup and Installation Steps eese 4 2 45 General Safety Guidelines acta aaa aere tonal dai lata ati dat det boat 4 2 4 6 Before Accessing the Mobile Rack mmm nene eenne ee ennneee ee aaea 4 2 4 7 Cooling Fan Installati n acasa ces on aa nr ta a ea d lt a da nt 4 3 Installing the Cooling Fan NR DR A ee ree tern OROS et 4 3 gis TT le a na ee i i a a da 4 3 4 8 Hard Drive Installation eee n ER rero ata e Ea aa da ala 4 4 4 9 Connect Data and Power Cables msi cai cazati ana t e a sa it a 4 6 4 10 Advanced COMMQUIAUON esa zei er i ii nisa a n a i te a r 4 6 M28SAB Mobile Rack User s Guide Contacting Supermicro Headquarters Address Super Micro Computer Inc 980 Rock Ave San Jose CA 95131 U S A Tel 1 408 503 8000 Fax 1 408 503 8008 Email marketing supermicro com General Information support supermicro com Technical Support Web Site www supermicro com Europe Address Super Micro Computer B V Het Sterrenbeeld 28 5215 ML s Hertogenbosch The Netherlands Tel 31 0 73 6400390 Fax 31 0 73 6416525 Email sales supermicro nl General Information support supermicro nl Technical Support rma supermicro nl Customer Support Asia Pacific Address Super Micro Computer Inc 4F No 232 1 Liancheng Rd Chung Ho 235 Taipei County Taiwan R O C Tel 886 2 8226 3990 Fax 886 2 8226 3991 Web Site www supermicro com tw Technical Supp
4. IABILITY FOR ANY HARDWARE SOFTWARE OR DATA STORED OR USED WITH THE PRODUCT INCLUDING THE COSTS OF REPAIRING REPLACING INTEGRATING INSTALLING OR RECOVERING SUCH HARDWARE SOFTWARE OR DATA Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California USA The State of California County of Santa Clara shall be the exclusive venue for the resolution of any such disputes Super Micro s total liability for all claims will not exceed the price paid for the hardware product California Best Management Practices Regulations for Perchlorate Materials This Perchlorate warning applies only to products containing CR Manganese Dioxide Lithium coin cells Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate WARNING Handling of lead solder materials used in this product may expose you to lead a chemical known to the State of California to cause birth defects and other reproductive harm Manual Revision 1 0 Release Date June 7 2011 Unless you request and receive written permission from Super Micro Computer Inc you may not copy any part of this document Information in this document is subject to change without notice Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders Copyright 2011 by Super Micro Computer Inc All rights reserved
5. Power connector JP1 8 Upgrade connector 2 JP47 4 Power connector JP3 9 Fan connector JP54 5 MG9071 chip 3 1 M28SAB Mobile Rack User s Guide 3 2 Front Components Connectors and Pin Definitions 1 2 SAS Ports The SAS ports are used to connect the Mini SAS cables The ports are designated SAS IN 0 3 and SAS IN 4 7 Each port is also compatible with SATA drives 3 4 Backplane Main Power Connectors Backplane Main Power The 4 pin connectors designated JP1 and 4 Pin Connectors JP3 provide power to the backplane See the Pin Definition table on the right for pin definitions Both of 1 412V these connectors must be used at the same 2 and 3 Ground time 5 6 MG9071 Chip The MG9071 chip is an enclosure manage ment controller chip 7 8 Upgrade Connector The upgrade connectors are designated JP46 and JP47 The upgrade connector is for manu facturing use only 9 Fan Connectors The fan connector is designated JP54 3 2 Safety Information and Technical Specifications 3 3 Front Jumper Locations and Pin Definitions Em p 34 SM E x um E OE Y Y d we pe 5 5 Oli 5 fiu B M o DIL 1 o O X E 4 NA JP61 Tp me SASIN 447 a gooaoaggeon W 4 wm B18 SAS IN 40 43 3 lesa PA p T4 T3 1FAN 3 ACTUD TEST UA N y NC it N C 8 X aS i va le a IS 5 w Z gt A e O I m x ws
6. Printed in the United States of America Safety Information and Technical Specifications Table of Contents Contacting SUP SIG s cac utat eric e bns ed act ca acc DRE a teases iv Returning Merchandise for SO VIGBs adesse pe ura inaite Doua ea e aa V Chapter 1 Safety Guidelines n ins aseamana anina aad ERR EA dansi nai aa 1 1 1 1 ESD Safety CS UNS sea car ana ea lol a e a aa a 1 1 1 2 General Safety Guidelines Tm 1 1 deo An Important Note 10 Users cinesino iina inoa 053 et Ca 0 De E 1 2 Chapter Nu 2 1 2 1 CD IPN VENI n aaa i RIP 2 1 2 2 Product ESalll 8S 25s certet eS ete RI Emend aaa at la iau tt d aa 2 1 Operalinu Sy SUS US ic cece se eee auc eee cede cece ii 2 1 Additional IN OrmaAtON esa ce Sats e ia e a a an a OE 2 2 Chapter 3 SAS I28A Backplane Specifications 3 1 3 1 Front Connectors and dull eoe escenas aaa na ai a ia dea podea asa aan 3 1 3 2 Front Components Connectors and Pin Definitions ssssssss 3 2 3 3 Front Jumper Locations and Pin Definitions sees 3 3 Explanation ON ici c 3 3 3 4 Rear Connectors and LED Indicators cepe ite dobaaii toane a eten lua bes Cass 3 4 Chapter 4 Mobile Rack Installation Instructions 4 1 4 1 SNIPPING BI dr eM eee 4 1 4 2 Tools Reguired aoa ea 4 1 4 3 Oth r
7. SUPERE M28SAB M28SAB OEM MOBILE RACK USER S GUIDE Rev 1 0 M28SAB Mobile Rack User s Guide The information in this User s Manual has been carefully reviewed and is believed to be accurate The vendor assumes no responsibility for any inaccuracies that may be contained in this document makes no commitment to update or to keep current the information in this manual or to notify any person or organization of the updates Please Note For the most up to date version of this manual please see our web site at www supermicro com Super Micro Computer Inc Supermicro reserves the right to make changes to the product described in this manual at any time and without notice This product including software and documentation is the property of Supermicro and or its licensors and is supplied only under a license Any use or reproduction of this product is not allowed except as expressly permitted by the terms of said license IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN PARTICULAR SUPERMICRO SHALL NOT HAVE L
8. and follow the instructions in this section 4 3 M28SAB Mobile Rack User s Guide 4 7 Cooling Fan Installation M28SAB Only Installing the Cooling Fan The M28SAB mobile rack includes a cooling fan not required on M28SAB OEM When using the M28SAB without installing the mobile rack in a larger unit such as a chassis a cooling fan must be installed on the mobile rack unit For more information on installing the mobile rack into a chassis or server see the documentation for your mobile rack or server You can also visit our Web site at http www supermicro com nstalling the Cooling Fan on the Mobile Rack 1 Align the mounting holes on the fan with the mounting holes in the mobile rack 2 Attach the cooling fan cable to the fan connector 3 Secure with two screws as illustrated Figure 4 1 Installing the Fan on the M28SAB Mobile Rack Fan Removal Removing the Cooling Fan from the Mobile Rack 1 Remove the fan cable from the mobile rack by gentlypulling the cable from the backplane 2 Remove the screws securing the fan to the mobile rack 3 Pull the fan away from the rear of the mobile rack 4 4 Safety Information and Technical Specifications 4 8 Hard Drive Installation Each M28 mobile rack includes dummy trays that act as place holders for hard drives Before using the mobile rack you must install hard drives into the drive carriers Hard drives are sold separately Release Tab
9. fety Guidelines To avoid personal injury and property damage carefully follow all the safety steps listed below when accessing your system or handling the components 1 1 ESD Safety Guidelines Electrostatic Discharge ESD can damage electronic components To prevent dam age to your system it is important to handle it very carefully The following measures are generally sufficient to protect your equipment from ESD Use a grounded wrist strap designed to prevent static discharge Touch a grounded metal object before removing a component from the antistatic bag Handle the mobile rack backplane by its edges only do not touch its compo nents peripheral chips memory modules or gold contacts When handling chips or modules avoid touching their pins Put the card and peripherals back into their antistatic bags when not in use General Safety Guidelines Always disconnect power cables before installing or removing any components from the computer including the backplane Disconnect the power cable before installing or removing any cables from the backplane Make sure that the backplane is securely and properly installed on the mother board to prevent damage to the system due to power shortage 14 M28SAB Mobile Rack User s Guide 1 3 An Important Note to Users All images and layouts shown in this user s guide are based upon the latest equip ment and PCB revision available at the time of publishing The card and eq
10. nfiguration Use the following instructions in the unlikely event that you must access the jump ers buzzer or other backplane components Remove Screws Aa Remove Screw Mobile Rack Casing NAM Screw Figure 4 4 Mobile Rack and Rear Casing Accessing the Mobile Rack Backplane Optional 1 Remove the two screws that secure the casing to the mobile rack 2 Slide the casing downward and remove it from the mobile rack 4 7 M28SAB Mobile Rack User s Guide Notes 4 8 Safety Information and Technical Specifications Disclaimer cont The products sold by Supermicro are not intended for and will not be used in life sup port systems medical equipment nuclear facilities or systems aircraft aircraft devices aircraft emergency communication devices or other critical systems whose failure to per form be reasonably expected to result in significant injury or loss of life or catastrophic property damage Accordingly Supermicro disclaims any and all liability and should buyer use or sell such products for use in such ultra hazardous applications it does so entirely at its own risk Furthermore buyer agrees to fully indemnify defend and hold Supermicro harmless for and against any and all claims demands actions litigation and proceedings of any kind arising out of or related to such ultra hazardous use or sale
11. ort Email support supermicro com tw Tel 886 2 8226 1900 Safety Information and Technical Specifications Returning Merchandise for Service A receipt or copy of your invoice marked with the date of purchase is required be fore any warranty service will be rendered You can obtain service by calling your vendor for a Returned Merchandise Authorization RMA number When returning to the manufacturer the RMA number should be prominently displayed on the outside of the shipping carton and mailed prepaid or hand carried Shipping and handling charges will be applied for all orders that must be mailed when service is complete For faster service RMA authorizations may be requested online http www super micro com support rma Whenever possible repack the mobile rack in the original Supermicro carton using the original packaging material If these are no longer available be sure to pack the mobile rack securely using packaging material to surround the mobile rack so that it does not shift within the carton and become damaged during shipping This warranty only covers normal consumer use and does not cover damages in curred in shipping or from failure due to the alteration misuse abuse or improper maintenance of products During the warranty period contact your distributor first for any product problems M28SAB Mobile Rack User s Guide Notes vi Safety Information and Technical Specifications Chapter 1 Sa
12. ps Use the following list as a guide to set up and install the mobile rack If this mobile rack is to be installed in a chassis use the instructions in the chassis manual Mobile Rack Chassis Installation T 4 5 Unpack and examine system parts Review all system and safety guidelines M28SAB Install the system fan as described in section 4 7 of this manual not required on M28SAB OEM M28SAB OEM Reset jumper JP61 to enable pins 2 3 without the fan connected Install the hard drives Connect data and power cables General Safety Guidelines Always disconnect power cables before installing or removing any components from the computer including the backplane Disconnect the power cable before installing or removing any cables from the mobile rack or backplane 4 2 Safety Information and Technical Specifications e Make sure that the backplane is securely and properly installed on the mother board to prevent damage to the system due to power shortage 4 6 Before Accessing the Mobile Rack Prior to Accessing the Mobile Rack 1 Power down and power supply connected to the chassis or server In addi tion unplug all power cords from the wall outlet 2 Disconnect all necessary cables and label the cables for easy identification 3 Use a grounded wrist strap designed to prevent static discharge when han dling components 4 Save all screws and fasteners for later use 5 Familiarize yourself with
13. structions listed in this manual to use the mobile rack independent of a chassis The pictures or graphics shown in this user s guide were based upon the latest revi sion available at the time of publication of this manual The M28SAB mobile rack may or may not look exactly the same as the graphics shown in this manual The availability of the SAS devices supported depends upon the readiness of firm ware and hardware support The SAS I28A mobile rack backplane has been designed to utilize the most up to date technology available providing your system with reliable high quality performance This manual reflects SAS I28A Revision 1 00 the most current release available at the time of publication Always refer to the Supermicro Web site at www supermicro com for the latest updates compatible parts and supported configurations 2 2 Safety Information and Technical Specifications Chapter 3 SAS I28A Backplane Specifications 3 1 Front Connectors and Jumpers SG gag UPGRADER UPON 2 tz pomum s 3 onoono T y z z M id t B E Logoooooonon O ri 2008 Aa C M g z Ei a e g A Q 9 OOO X97 LO JK WS Ho if O DESIGNED IN USA SE vous BPN SASI28A REV 100 Figure 3 1 Front Connectors and Components Front Connectors and Components 1 SAS IN 0 3 JSM1 6 MG9071 chip 2 SAS IN 4 7 JSM2 7 Upgrade connector 1 JP46 3
14. uipment you have received may or may not look exactly the same as the graphics shown in this manual 1 2 Safety Information and Technical Specifications Chapter 2 Introduction 2 1 Overview This manual has been written for system integrators PC technicians and knowledgeable PC users It provides detailed information for the installation and use of the M28SAB mobile rack The Supermicro M28SAB mobile rack showcases advanced technology innovations in modular connectivity and data transferability and supplies reliable effective and scalable solutions for tomorrow s data communications industry 2 2 Product Features The M28SAB mobile rack includes the following e Slim design pocket size 5 3 4 width x 3 3 8 height e Supports a 8 x 2 5 small form factor hard disk drive e Supports up to 5V 10A average and 12V 10A average e Supports SAS 2 0 and SATA III at 6 Gbps transfer speed Operating Systems This mobile rack supports the following operating systems e Windows 2000 Windows XP Windows 7 and Windows 2003 e Linux Red Hat and SuSE For the most current information on supported operating systems visit the Supermicro Web site at www supermicro com 2 1 M28SAB Mobile Rack User s Guide Additional Information The M28SAB mobile rack was designed for use in certain chassis and servers or as an optional unit for storage expansion Use the chassis or server manual for installation instructions Use the in
15. ure 3 3 Rear Connectors and LED Indicators Rear LEDs Description OH DRIVE FAIL FAN FAIL Rear SAS SATA Connectors and LED Indicators Rear Connector Hard Drive Activity LED Failure LED SAS Drive SAS 0 D31 D30 SAS SATA HDD 0 SAS 1 D33 D32 SAS SATA HDD 1 SAS 2 D35 D34 SAS SATA HDD 2 SAS 3 D37 D36 SAS SATA HDD 3 SAS 4 D39 D38 SAS SATA HDD 4 SAS 5 D41 D40 SAS SATA HDD 5 SAS 6 D43 D42 SAS SATA HDD 6 SAS 7 D45 D44 SAS SATA HDD 7 3 4 Safety Information and Technical Specifications Chapter 4 Mobile Rack Installation Instructions 4 1 Shipping Lists for M28SAB and M28SAB OEM Examine the your order for the following parts M28SAB e One M28SAB mobile rack One 40 mm cooling fan Thirty two M3 screws e Four round head screws M28SAB OEM One M28SAB mobile rack e Thirty two M3 screws Four round head screws 4 2 Tools Required M28SAB series mobile rack assembly requires the following Phillips head screwdriver e Industry standard anti static strap recommended 4 1 M28SAB Mobile Rack User s Guide 4 3 Other Parts When using this mobile rack independent of a chassis you may need the follow ing parts 4 4 Two 4 pin power cords to connect the mobile rack to a power supply SAS iPass cable part numbers CBL 0108L 39 cm CBL 0281L 75 cm or CBL 0294L 01 are used to connect the SAS ports to the motherboard or RAID controller Setup and Installation Ste
Download Pdf Manuals
Related Search