Huawei S2700-18TP-EI-AC
Contents
1. The card power and PoE power are abnormal If a single power supply unit is installed the PoE power is out of range If two power supply units are installed the card power or PoE power is out of range The power supply indicator units are not present or the power supply is abnormal when a single power supply unit is used Two power supply units are installed properly but not switched on The power supply units are switched off The card power and PoE power are abnormal If a single power supply unit is installed the PoE power is out of range If two power supply units are installed the card power or PoE power is out of range Issue 02 2012 10 27 Huawei Proprietary and Confidential 13 Copyright Huawei Technologies Co Ltd S27008 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction System status SYS The system is not indicator operating Green The system is not operating properly or is starting Orange The system is performing self check during startup Blinking green The system is operating properly After registering the system does not operate properly or a power alarm fan alarm or temperature alarm is generated Mode The service interface indicator indicator is in the default mode STAT The service interface indicator indicates the interface speed After 45 seconds the service interface indicator automatically resto2. 2700 amp S3700 Series Ethernet Switches V100R006C03 Quick Start Issue 02 Date 2012 10 27 Wz HUAWEI TECHNOLOGIES CO LTD HUAWEI Copyright Huawei Technologies Co Ltd 2012 All rights reserved No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co Ltd Trademarks and Permissions uawa and other Huawei trademarks are trademarks of Huawei Technologies Co Ltd All other trademarks and trade names mentioned in this document are the property of their respective holders Notice The purchased products services and features are stipulated by the contract made between Huawei and the customer All or part of the products services and features described in this document may not be within the purchase scope or the usage scope Unless otherwise specified in the contract all statements information and recommendations in this document are provided AS IS without warranties guarantees or representations of any kind either express or implied The information in this document is subject to change without notice Every effort has been made in the preparation of this document to ensure accuracy of the contents but all statements information and recommendations in this document do not constitute a warranty of any kind express or implied Huawei Technologies Co Ltd Address Huawei Industrial Base Bantian Longgang Shenzhen 51812
3. Copyright Huawei Technologies Co Ltd S27008 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Figure 2 2 Naming rules 93700 28TP PWR El AB CD E F 93700 52P EI 24S DC CDF GH 3700 28TP SI AC CD FH S3700 28TP El MC AC CDFI H Ide Description ipa eR B Product series 37 indicates the S3700 series C Maximum number of interfaces NOTE The number of interfaces on an 3700 can be 28 or 52 depending on the device model The 3700 supports Power over Ethernet PoE NOTE If this letter is not displayed PoE is not supported Uplink interface type P A device has optical interfaces TP A device has combo interfaces supporting optical and electrical interfaces Issue 02 2012 10 27 Huawei Proprietary and Confidential 7 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Description Software version type EI enhanced version supporting enhanced features SI standard version supporting basic features Downlink interface type The value 24S indicates that 24 downlink interfaces of the S3700 52P EI 24S are optical interfaces NOTE If this letter is not displayed all downlink interfaces are electrical interfaces Powering mode AC alternating current power DC direct current power ae The device has monitoring interfaces 2 3 S2700 Indicator Descript
4. Internet Explorer 6 0 on the client Enter the universal resource locator URL of the Web system client in the address bar and press Enter The User Login dialog box is displayed as shown in Figure 5 6 The URL is in the format http IP view login html for example http 10 164 19 131 view login html Issue 02 2012 10 27 Huawei Proprietary and Confidential 36 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 5 Logging in to the Device Step 3 Step 4 Step 5 Figure 5 6 Login User Login Wz HUAWEI User Name admin Password eeeee Verify Code ek4x EK 4X Language English x M Save my password Login Reset Enter values in User Name Password and Verify Code The local switch provides a default account The user name and password of the account are admin To create change or delete user names and passwords choose Security gt AAA gt User Management Users of levels 0 1 and 2 has only visit level rights and can view only the Ping and Tracert pages after logging in to the client Choose a language for example English The Web system client of the current version supports Chinese and English After logging in to the client you can select another language from the Language drop down list on the top right corner of the page Click Login CO note Ifyou select Save my password before clicking Login you do n
5. Switches Quick Start 2 Product Hardware Introduction linking green The system is operating properly Blinki Red After registering the system does not operate properly or a power alarm fan alarm or temperature alarm is generated f E Mode Ofi The service interface indicator indicator is in the default mode STAT Green The service interface indicator indicates the interface speed After 45 seconds the service interface indicator automatically restores to off Orange The service interface indicator indicates the PoE status After 45 seconds the service interface indicator automatically restores to off As shown in Figure 2 4 the S2700 has a mode switching button 5 You can press the mode switching button to change the display mode of the mode indicator The status of the mode indicator represents the display mode of the related interface indicator For example when you press the mode switching button once on S2700 9TP PWR EI the mode indicator turns green and the related interface indicator enters the speed state When you press the mode switching button for a second time the mode indicator turns orange and the related interface indicator represents the PoE power status When you press the mode switching button for a third time the mode indicator restores to the default state off If you do not press the mode switching button within 45 seconds the mode indicator automatically restores to off The follo
6. The device is a not a command switch Ifthe indicator of an interface is always on the number of this interface is the stack ID of the device If the first nine interface indicators of the device are always on the stack ID of the device is 0 Blinking green The device is a command switch Ifthe indicator of an interface blinks the number of this interface is the stack ID of the device If the first nine interface indicators of the device blink the stack ID of the device is 0 Issue 02 2012 10 27 Huawei Proprietary and Confidential 21 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 3 Device Installation 3 Device Installation This section describes how to install the S2700 amp S83700 For details on device installation see the 2700 amp 3700 amp 5700 amp 6700 Quick Installation Guide CI note You can obtain the paper documentation of the Quick Installation Guide from delivered accessories To obtain the electronic documentation of the Quick Installation Guide see Where to Obtain Documentation Issue 02 2012 10 27 Huawei Proprietary and Confidential 22 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 4 Powering on the Device Powering on the Device About This Chapter This section describes the check items and the procedure for powering on and powering off the device 4 1 Checking Before Power
7. 700 9TP EI DC and one GE combo interface 10 100 1000BASE T 100 1000BASE X S 2700 18TP SI AC 18 2700 18TP EI AC There are sixteen 10 100BASE T Ethernet interfaces and two GE combo interfaces 10 100 1000BASE T 100 1000BASE X S 2700 26TP SI AC 26 S2700 26TP EI AC There are twenty four 10 100BASE T Ethernet S2700 26TP EI DC interfaces and two GE combo interfaces 10 100 1000BASE T 100 1000BASE X 2700 52P EI AC 52 S2710 52P SI AC There are forty eight 10 100BASE T Ethernet S2700 52P PWR EI interfaces two 100 1000BASE X Ethernet optical interfaces and two GE SFP interfaces S 2710 52P PWR SI S2700 9TP PWR EI 9 There are eight 10 100BASE T Ethernet interfaces and one GE combo interface 10 100 1000BASE T 100 1000BASE X S2700 26TP PWR EI 26 There are twenty four 10 100BASE T Ethernet interfaces and two GE combo interfaces 10 100 1000BASE T 100 1000BASE X Issue 02 2012 10 27 Huawei Proprietary and Confidential 3 Copyright Huawei Technologies Co Ltd S27008 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Naming Rules The following are the naming rules of the S2700 26TP PWR EI 2710 52P SI AC S2700 52P EI and 2700 9TP SI Figure 2 1 Naming rules 2700 26TP PWR El 92710 52P SI AC AB C DEG H S2700 52P EI AC DEG H S2700 9TP SI DEG Description er B Product series 27 indicates the S2700 series Product subseries Maximum number o
8. 9 People s Republic of China Website http enterprise huawei com Issue 02 2012 10 27 Huawei Proprietary and Confidential i Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start About This Document About This Document Intended Audience This document describes how to verify basic functions of the 2700 S2752 S3700 during the deployment to ensure stable and reliable running of the S2700 S2752 S3700 on the network This document is intended for Data configuration engineers Commissioning engineers Network monitoring engineers System maintenance engineers Symbol Conventions The symbols that may be found in this document are defined as follows Indicates a hazard with a high level of risk which if not avoided will result in death or serious injury Indicates a hazard with a medium or low level of risk which if not avoided could result in minor or moderate injury Indicates a potentially hazardous situation which if not avoided could result in equipment damage data loss performance degradation or unexpected results Issue 02 2012 10 27 Huawei Proprietary and Confidential ii Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start About This Document Command Conventions The command conventions that may be found in this document are defined as follows Boldface The keywords of a command li
9. aionein 2 Z STOU CO a E R R E 3 CSD TIL E E ee er A E E S E A E P I E E E rere 5 Dodane TON Ta Gaor Deste O ries ER E A E e aiuerasamnne 8 24 S3700 mndicator Descriptions tues scans esa r eaae tea E a Ra aaa A AATA ara aa ERA ema RaR k 16 3 Device Tnstalla HOi sna E eens 22 4 Powering o the Device iinet anaes 23 ALEN B eTO T cteyaceascasaceaaideniactaciae enacnbaaescenrsaciacesyaaceduetahiesaesncioccace 24 22 PO erie on the Devii sring E ree ee 28 al gt Checkins Aner Power Oliana A Ei RE ae ee eRe 28 5 Lopeing in to the Ty aia sesis sina chasstassssinncsaeiastsanaaidanin Aaii 29 5 1 Logging Into the Switch Through the Console InterfatC iisiiisriiciicsesrerirsiriircriicsrisibrkesiieibideitesiiikiiisa kta 30 5 2 Example for Configuring to Manage the Switch Through Telnet i i 5 csncossaccsncassceacce sacsesmecantesnecssaceuncasscosneas 33 5 3 Logging In to the Web SystemC etl csc decrease aaan araara VaR a aE ANAR a Eaa I ait 36 6 Service Deploy meib uisesanie R ATE 38 7 Obiamine Documenta fissile ainene 39 Issue 02 2012 10 27 Huawei Proprietary and Confidential iv Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 1 Overview 1 Overview This document helps you quickly learn how to use the S2700 amp S3700 Figure 1 1 shows the quick start contents This section provides an overview of quick start Figure 1 1 Quick start contents Describes switch models and Indicators on each m
10. curity gt Switches Online Help The online help is integrated and released with the product software You can view the online help by Selecting Help on the NMS interface Issue 02 2012 10 27 Huawei Proprietary and Confidential 39 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 7 Obtaining Documentation Pressing F1 on any interface of the NMS Release Documents Release documents are released with the software package You can apply to Huawei technical support personnel for the documents Issue 02 2012 10 27 Huawei Proprietary and Confidential 40 Copyright Huawei Technologies Co Ltd
11. ers is 15 and the current number of VTY users on line is 3 lt SwitchA gt Configuration Files SwitchA sysname SwitchA vlan batch 1 vlan 1 description admin_VLAN Issue 02 2012 10 27 Huawei Proprietary and Confidential 35 Copyright Huawei Technologies Co Ltd 2700 amp S3700 Series Ethernet Switches Quick Start 5 Logging in to the Device interface Vlanifl ip address 10 10 10 10 255 255 255 0 interface GigabitEthernet0 0 1 port link type trunk port trunk allow pass vlan 1 aaa local user huawei password simple huawei local user huawei service type telnet local user huawei privilege level 15 authentication scheme default authorization scheme default accounting scheme default domain default user interface con 0 user interface vty 0 4 authentication mode aaa return 5 3 Logging In to the Web System Client Context Procedure Step 1 Step 2 Before configuring the switch you must log in to the Web system client Before logging in to the Web system client ensure that the switch has been commissioned and the Web system server is enabled on the switch The Web system client connects to the switch through HTTP therefore you must log in to the Web system client through HTTP The Web system client supports the Microsoft Internet Explorer 6 0 IE6 and Firefox 3 0 or later versions The Web system client described in this document uses the IE6 Open Microsoft
12. es and two GE combo interfaces 10 100 1000BASE T 100 1000BASE X Issue 02 2012 10 27 Huawei Proprietary and Confidential 5 Copyright Huawei Technologies Co Ltd S27008 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Produ Maximum Number of Interfaces ct Series 3700 52P SI AC 52 S 3700 52P EI AC There are forty eight 10 100BASE T Ethernet 3700 52P FI DC interfaces two 100 1000BASE X Ethernet optical interfaces and two GE SFP interfaces S3700 52P EI 24S AC 52 S3700 52P EI 24S DC There are twenty four 10 100BASE T Ethernet interfaces twenty four 1 OOBASE X Ethernet interfaces two 100 1000BASE X Ethernet optical interfaces and two GE SFP interfaces S3700 52P EI 48S AC 52 S3700 52P EI 48S DC There are forty eight 1OOBASE X Ethernet interfaces two 100 1000BASE X Ethernet optical interfaces and two GE SFP interfaces S3700 28TP PWR EI 28 S3700 28TP PWR SI There are twenty four 10 100BASE T Ethernet interfaces two GE SFP interfaces and two GE combo interfaces 10 100 1000BASE T 100 1000BASE X S 3700 52P PWR EI 52 S3700 52P PWR SI There are forty eight 10 100BASE T Ethernet interfaces two 100 1000BASE X Ethernet optical interfaces and two GE SFP interfaces Naming Rules The following are the naming rules of the 3700 28TP PWR EI S3700 52P EI 24S S3700 28TP EI MC and S3700 28TP SI Issue 02 2012 10 27 Huawei Proprietary and Confidential 6
13. f interfaces NOTE The number of interfaces on an S2700 can be 9 18 26 or 52 depending on the device model E Uplink interface type P A device has optical interfaces TP A device has combo interfaces supporting optical and electrical interfaces Issue 02 2012 10 27 Huawei Proprietary and Confidential 4 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Ide Description ntifi er The 2700 supports Power over Ethernet PoE NOTE If this letter is not displayed PoE is not supported Software version type EI enhanced version supporting enhanced features SI standard version supporting basic features Powering mode AC alternating current power DC direct current power 2 2 S3700 Introduction This section describes 3700 models Device Models To meet diverse customer requirements the S3700 provides a variety of models Table 2 2 lists these device models You can select a device model as required Table 2 2 Device models Maximum Number of Interfaces S 3700 28TP SI AC 28 S3700 28TP SI DC There are twenty four 10 100BASE T Ethernet S3700 28TP EI AC interfaces two GE SFP interfaces and two GE combo interfaces 10 100 1000BASE T 100 1000BASE X 3700 28TP EI DC S 3700 28TP EI MC AC S3700 28TP EI 24S AC 28 There are twenty four 1 OOBASE X Ethernet interfaces two GE SFP interfac
14. f you do not press the mode switching button within 45 seconds the mode indicator automatically restores to off The following table describes the meanings of indicators Table 2 7 Description of indicators in different modes STAT Off The interface is not connected or has been shut down The interface is connected Blinking green The interface is sending or receiving data Speed Off The interface is not connected or has been shut down Green The interface speed is 10 Mbit s or 100 Mbit s ff i Blinking green The interface speed is 1000 Mbit s PoE O The interface does not provide remote power Green The interface is providing remote power Blinking green The power of the powered device PD exceeds the power supply capability of the port or exceeds the threshold Stack Off The stack ID of the member switch is not the number of an interface in the off state Issue 02 2012 10 27 Huawei Proprietary and Confidential 15 Copyright Huawei Technologies Co Ltd S27008 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Green The device is a not a command switch Ifthe indicator of an interface is always on the number of this interface is the stack ID of the device If the first nine interface indicators of the device are always on the stack ID of the device is 0 Blinking green The device is a command switch Ifthe indicator of an interface blinks the number of this inter
15. face is the stack ID of the device If the first nine interface indicators of the device blink the stack ID of the device is 0 2 4 S3700 Indicator Description This section describes the indicators on the 3700 front panel Indicators of a Non PoE S3700 S3700 28TP SI AC is a non PoE switch that has a single power supply unit Figure 2 6 3700 28TP SI AC indicators 3 12 i Me Huawei Quid 3700 Sesjes i E Table 2 8 Description of S3700 28TP SI AC indicators Power for The switch is powered off indicator The switch is powered on Issue 02 2012 10 27 Huawei Proprietary and Confidential 16 Copyright Huawei Technologies Co Ltd S27008 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction System lor The system is not operating status indicator Green The system is not operating properly or is starting Blinking The system is operating green properly Port LNK ACT Off The interface is not connected indicator or has been shut down The interface is connected Blinking The interface is sending or green receiving data Indicators of a PoE 3700 3700 52P PWR EI is a PoE switch Figure 2 7 3700 52P PWR EI indicators HHI TETE PS oe i Table 2 9 Description of S3700 52P PWR EI indicators Power PWR The power supply indicator units are not present or the power supply is abnormal when a single power supply unit is
16. hA SwitchA interface vlanif 1 SwitchA Vlanif1 ip address 10 10 10 10 255 255 255 0 SwitchA Vlanif1 quit Configure the Telnet service on SwitchA Set the authentication method to AAA user name to huawei and password to huawei Set the service type to telnet and user level to 15 Configure AAA authentication for the users at the vty 0 to vty 4 levels SwitchA aaa SwitchA aaa local user huawei password simple huawei SwitchA aaa local user huawei service type telnet SwitchA aaa local user huawei privilege level 15 SwitchA aaa quit SwitchA user interface vty 0 4 SwitchA ui vty0 4 authentication mode aaa SwitchA ui vty0 4 return lt SwitchA gt Verify the configuration CO note When the administrator logs in to SwitchA through Telnet ensure that the PC of the administrator and SwitchA are reachable at the network layer lt SwitchA gt telnet 127 0 0 1 TEYIN Let 06 Ou Press CTRL T to abort Connected to 127 0 0 1 KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKAKK ia All rights reserved 2005 2007 x Without the owner s prior written consent no decompiling or reverse engineering shall be allowed Notice z This is a private communication system Unauthorized access or use may lead to prosecution KKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKKK Login authentication Username huawei Password Note The max number of VTY us
17. ion Indicators of a Non PoE S2700 S 2700 9TP SI AC is a non PoE switch Figure 2 3 2700 9TP SI AC indicators Quidway 52700 Series Table 2 3 Description of S2700 9TP SI AC indicators Power PWR The switch is powered off indicator we The switch is powered on status properly or is starting Issue 02 2012 10 27 Huawei Proprietary and Confidential 8 Copyright Huawei Technologies Co Ltd S27008 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Blinking The system is operating green properly 3 Port LNK ACT Off The interface is not connected indicator or has been shut down 4 The interface is connected Blinking The interface is sending or green receiving data M note SYS on the front panel of an S2710 52P SI AC indicates the system status indicator The indicator status the meanings and their relationships are the same as those indicated by RUN in the preceding table Indicators of a PoE S2700 S 2700 26TP PWR EI is a PoE switch LO note S2700 9TP PWR EI has only one power supply unit so the power indicator is identified by PWR The indicator status the meanings and their relationships on an S2700 52P PWR EI are the same as those on an 2710 52P PWR SI Figure 2 4 2700 26TP PWR EI indicators Ba Be f Table 2 4 Description of S2700 26TP PWR EI indicators Power PWRI The power supply units are indicator not present or the power
18. itches Quick Start 4 Powering on the Device Table 4 4 Signal cable checklist 3 1 All the signal cables to be deployed pass the continuity check 2 No signal cable is placed on the heat dissipation holes of the cabinet 3 The bent part of a signal cable cannot be too tight 4 The cables in the cabinet cannot be crossed and the cables outside the cabinet are bound The two ends ofa signal cable are clearly identified by labels and the texts on the labels are in the same direction The bolts that fix the cables are tightened 4 2 Powering on the Device Turn on the power module of the device 4 3 Checking After Power on Check the following items after the device is powered on The sound of fan rotating can be heard and that the air exhaust from the air vents can be felt The indicators of the power modules run normally Normally the INPUT and OUTPUT indicators are on The indicators of the fan modules run normally Normally the STATUS indicator is on Issue 02 2012 10 27 Huawei Proprietary and Confidential 28 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 5 Logging in to the Device Logging in to the Device About This Chapter This section describes how to log in to the device 5 1 Logging In to the Switch Through the Console Interface 5 2 Example for Configuring to Manage the Switch Through Telnet 5 3 Logging In to the Web Syste
19. m Client Before configuring the switch you must log in to the Web system client Issue 02 2012 10 27 Huawei Proprietary and Confidential 29 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 5 Logging in to the Device 5 1 Logging In to the Switch Through the Console Interface Context When establishing the configuration environment through the console interface you can log in to theS2700 amp 3700 through the HyperTerminal in Windows Procedure Step 1 Start the HyperTerminal Choose Start gt All Program gt Accessories gt Communications gt HyperTerminal to start the HyperTerminal in Windows XP Step 2 Set up a connection See Figure 5 1 Enter the name of the new connection in the Name text box and then choose one icon Then click OK Figure 5 1 Setting up a connection Connection Description a New Connection Enter a name and choose an ican for the connection Step 3 Configure an interface for connection In the Connect To dialog box as shown in Figure 5 2 select an interface from the drop down list box according to the actual interface on the PC or terminal Next click OK Issue 02 2012 10 27 Huawei Proprietary and Confidential 30 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 5 Logging in to the Device Figure 5 2 Configuring the interface for connection Connect To B COMM1 Ente
20. mode indicator turns orange and the related interface indicator represents the PoE power status When you press the mode switching button for a third time the mode indicator turns red and the related interface indicator represents the stack status When you press the mode switching button for a fourth time the mode indicator restores to the default state off If you do not press the mode switching button within 45 seconds the mode indicator automatically restores to off The following table describes the meanings of indicators Table 2 10 Description of indicators in different modes STAT Off The interface is not connected or has been shut down The interface is connected O Blinking green The interface is sending or receiving data The interface is not connected or has been shut down fi Speed ff Green The interface speed is 10 100 Mbit s Blinking green The interface speed is 1000 Mbit s ff i PoE O The interface does not provide remote power Green The interface is providing remote power Blinking green The power of the powered device PD exceeds the power supply capability of the port or exceeds the threshold Stack Off The stack ID of the member switch is not the number of an interface in the off state Issue 02 2012 10 27 Huawei Proprietary and Confidential 20 Copyright Huawei Technologies Co Ltd S27008 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Green
21. ne are in boldface Italic Command arguments are in italics Items keywords or arguments in brackets are optional x y Optional items are grouped in braces and separated by vertical bars One item is selected xly Optional items are grouped in brackets and separated by vertical bars One item is selected or no item is selected Optional items are grouped in braces and separated by vertical bars A minimum of one item or a maximum of all items can be selected Optional items are grouped in brackets and separated by vertical bars Several items or no item can be selected The parameter before the amp sign can be repeated 1 to n times A line starting with the sign is comments Change History Updates between document issues are cumulative Therefore the latest document issue contains all changes made in previous issues Changes in Issue 02 2012 10 27 Based on issue 01 2012 06 30 the document is updated as follows Some contents are modified according to updates in the product such as features and commands Changes in Issue 01 2012 06 30 Initial commercial release Issue 02 2012 10 27 Huawei Proprietary and Confidential iii Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start Contents Contents About This DOCH snnandicnnacennnnanea ea li LAGI sian senior eon 1 2 Product Hardware INQ chiotisicicincaminnhiontemmninarmamnndionsmnnonme
22. ng properly After registering the system does not operate properly or a power alarm fan alarm or temperature alarm is generated Mode The service interface indicator indicator is in the default mode STAT The service interface indicator indicates the interface speed After 45 seconds the service interface indicator automatically restores to off The service interface indicator indicates the PoE status After 45 seconds the service interface indicator automatically restores to off The service interface indicator indicates the stack ID After 45 seconds the service interface indicator automatically restores to off Issue 02 2012 10 27 Huawei Proprietary and Confidential 19 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction As shown in Figure 2 7 the button marked 5 is the mode switching button On an 3700 you can press the mode switching button to switch the display modes of interface indicators The status of a mode indicator represents the display mode of the related interface indicator For example the mode indicator of S3700 28TP PWR EI is off and the interface indicators are in STAT state by default When you press the mode switching button once the mode indicator turns green and the related interface indicator enters the speed state When you press the mode switching button for a second time the
23. odel Provides reference for device installation Describes precautions to take before and after you power on a switch Describes how to log in to a switch Provides reference for deploying services on a switch Obtaini Helps you obtain product documentation quickly Docume Issue 02 2012 10 27 Huawei Proprietary and Confidential 1 Copyright Huawei Technologies Co Ltd S27008 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Product Hardware Introduction About This Chapter This section describes models and indicators of low end switches 2 1 S2700 Introduction This section describes S2700 models 2 2 3700 Introduction This section describes 3700 models 2 3 S2700 Indicator Description 2 4 S3700 Indicator Description This section describes the indicators on the 3700 front panel Issue 02 2012 10 27 Huawei Proprietary and Confidential 2 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction 2 1 S2700 Introduction This section describes S2700 models Device Models To meet diverse customer requirements the S2700 provides a variety of models Table 2 1 lists these device models You can select a device model as required Table 2 1 Device models Produ Maximum Number of Interfaces ct Series S2700 9TP SI AC 9 S2700 9TP EI AC There are eight 10 100BASE T Ethernet interfaces S2
24. on After hardware installation is complete you need to check the device installation and cable installation 4 2 Powering on the Device 4 3 Checking After Power on Issue 02 2012 10 27 Huawei Proprietary and Confidential 23 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 4 Powering on the Device 4 1 Checking Before Power on After hardware installation is complete you need to check the device installation and cable installation M note Before power on you need to check the device cabinet cables connectors sockets labels and on site environment Device Installation Checklist A CAUTION Before power on all the power distribution cabinets and power distribution frames must be off Table 4 1 describes the device installation checklist Table 4 1 Device installation checklist 1 The cabinet is installed according to the Check the cabinet according to the dimensions on the design paper project design document 2 The expansion bolts for fixing the cabinet or base support to the ground are fastened The plain washer spring washer and nut bolt are installed correctly Issue 02 2012 10 27 Huawei Proprietary and Confidential 24 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 4 Powering on the Device The installation holes on the support and Use the multimeter to measure the the expansion bolt
25. ot need to enter the user name and password at next login After you log in to the Web system the main page is displayed For details about the main page see Window Layout End Issue 02 2012 10 27 Huawei Proprietary and Confidential 37 Copyright Huawei Technologies Co Ltd S27008 amp S3700 Series Ethernet Switches Quick Start 6 Service Deployment Service Deployment This section describes service deployment For details on service deployment see the corresponding configuration guides Issue 02 2012 10 27 Huawei Proprietary and Confidential 38 Copyright Huawei Technologies Co Ltd S27008 amp S3700 Series Ethernet Switches Quick Start 7 Obtaining Documentation 7 Obtaining Documentation You can obtain product documentation online help and release documents in various ways Product Documents Table 7 1 shows how to obtain product documents Table 7 1 Obtaining product documents Phase How to Obtain Documentation HedEx Library Single Electronic Document Installation From the electronic From http documentation delivered with enterprise huawei com the equipment From http support huawei com From the local Huawei representative office Version upgrade From http support huawei com From the local Huawei representative office M note Obtain the product documents from http enterprise huawei com by choosing Support gt Documentation Center gt IP Network amp Se
26. r details for the phone number that you want to dial Country region Area code Phone number Step 4 Set communication parameters When the COM1 Properties dialog box is displayed as shown in Figure 5 3 specify the parameters listed in Table 5 1 QO note In other Windows operating systems bits per second may be described as baud rate and data stream control may be described as traffic control Issue 02 2012 10 27 Huawei Proprietary and Confidential 31 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 5 Logging in to the Device Figure 5 3 Specifying parameters COM1 Properties Port Settings Bits per second Data bits Parity Stop bits Flow control Table 5 1 Parameters Bit per second baud rate 9600 Data bit Parity check Stop bit Flow control traffic control Step 5 After the HyperTerminal starts choose FileAttributes to display the COMM1 Properties dialog box as shown in Figure 5 4 On the Setting tab select VT100 in the Emulation drop down list box Click OK to complete the setting Issue 02 2012 10 27 Huawei Proprietary and Confidential 32 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 5 Logging in to the Device Figure 5 4 Selecting the terminal type COMM1 Properties Connect To Settings Function arrow and ctrl keys act as Terminal keys O Window
27. res to off The service interface indicator indicates the PoE status After 45 seconds the service interface indicator automatically restores to off The service interface indicator indicates the stack ID After 45 seconds the service interface indicator automatically restores to off Issue 02 2012 10 27 Huawei Proprietary and Confidential 14 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction As shown in Figure 2 5 the button marked 5 is the mode switching button On an S2700 you can press the mode switching button to switch the display modes of interface indicators The status of the mode indicator represents the display mode of the related interface indicator For example the mode indicator of S2710 52P PWR SI is off and the interface indicators are in STAT state by default When you press the mode switching button once the mode indicator turns green and the related interface indicator enters the speed state When you press the mode switching button for a second time the mode indicator turns orange and the related interface indicator represents the PoE power status When you press the mode switching button for a third time the mode indicator turns red and the related interface indicator represents the stack status When you press the mode switching button for a fourth time the mode indicator restores to the default state off I
28. s adapt to each other resistance between the bolt and the to ensure insulation between the support ground bolt of the rack The resistance and the ground and between the floor bracket and the guide rail The surfaces of the cabinets in the same row should be on the same plane The cabinets are arranged closely and tidily The cabinets on the sides of the main path are aligned The position error should be less than 5 mm The accessories of the front and rear doors are completely installed and the connection board is installed for combining cabinets The front door of a cabinet can be opened and closed easily Issue 02 2012 10 27 Huawei Proprietary and Confidential 25 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 4 Powering on the Device The card is installed and removed easily The screws on the panel should be appropriately tightened and easily disassembled The spring wire is intact The cabinet surface must be tidy and clean the components of the cabinet cannot be distorted all identifiers are correct clear and complete The cabinet is kept clean and there are no excessive binding straps and other articles in the cabinet The ESD wrist straps are connected the ESD jack in the chassis 11 Blank panels are installed in all empty slots Cable Installation Checklist Table 4 2 describes the cable installation checklist Table 4 2 Cable in
29. s keys Backspace key sends Cth Del Cti H Space Ctri H Telnet terminal ID VT100 Backscroll buffer lines 500 C Play sound when connecting or disconnecting Input Translation ASCII Setup End Follow up Procedure After the preceding configurations are complete press Enter If the prompt lt Quidway gt is displayed on the screen it indicates that the Command Line Interface CLI is displayed In this case you can enter commands to configure or manage the 27008 amp 3700 For details on configuration procedures see the following sections 5 2 Example for Configuring to Manage the Switch Through Telnet Networking Requirements As shown in Figure 5 5 SwitchA is newly added to the network SwitchA and SwitchB are connected through a trunk link To enable the network administrator to manage SwitchA remotely you need to configure the Telnet service and set the device name on SwitchA Issue 02 2012 10 27 Huawei Proprietary and Confidential 33 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 5 Logging in to the Device Figure 5 5 Networking diagram of managing SwitchA through Telnet administrator SwitchB GE 0 0 1 RS 232 serial port Console port OF x Console apie PC SwitchA GE 0 0 1 Configuration Roadmap The configuration roadmap is as follows Log in to SwitchA through the console interface Set
30. stallation checklist 1 The power cables and ground cables must be the copper wires and have no splice The cables are safely connected complying with standards Issue 02 2012 10 27 Huawei Proprietary and Confidential 26 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Switches Quick Start 4 Powering on the Device 2 The power cables and ground cables are connected safely The spring washer of the ground cable terminal is on the flat washer 3 The lugs of the power cables and ground cables are soldered or crimped tightly The power cables and ground cables are not crossed and are separated from other The redundant part of the power cables and ground cables should be cut The cables cannot be circled Labels are filled and attached to power cables and PGND cables power cables and PGND cables including power distribution switches are labeled correctly and clearly Labels are attached 20 mm from the connector The clearance between the power cable PGND cable and signal cable must be more than 30 mm Table 4 3 describes the cabinet cable checklist Table 4 3 Cabinet cable checklist mo um O a Cables are correctly connected 2 Cable ties are not overlapped and connectors are smooth Table 4 4 describes the signal cable checklist Issue 02 2012 10 27 Huawei Proprietary and Confidential 27 Copyright Huawei Technologies Co Ltd S2700 amp S3700 Series Ethernet Sw
31. supply is abnormal when a single power supply unit is used Green The power supply is normal Issue 02 2012 10 27 Huawei Proprietary and Confidential 9 Copyright Huawei Technologies Co Ltd S27008 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Two power supply units are installed properly but not switched on The power supply units are switched off The card power and PoE power are abnormal Orange If a single power supply unit is installed the PoE power is out of range If two power supply units are installed the card power or PoE power is out of range Orange If a single power supply unit is installed the PoE power is out of range If two power supply units are installed the card power or PoE power is out of range The system is not operating Green The system is not operating properly or is starting Orange The system is performing self check during startup Issue 02 2012 10 27 Huawei Proprietary and Confidential 10 Copyright Huawei Technologies Co Ltd System status indicator Power The power supply units are indicator not present or the power supply is abnormal when a single power supply unit is used Green The power supply is normal Two power supply units are installed properly but not switched on The power supply units are switched off The card power and PoE power are abnormal S27008 amp S3700 Series Ethernet
32. the device name Configure a management VLAN On SwitchA set the type of the interface that connects SwitchA and SwitchB to trunk Add the interface to the management VLAN in trunk mode Configure the management IP address of SwitchA Configure the Telnet service Data Preparation To complete the configuration you need the following data ID ofthe management VLAN Management IP address of SwitchA Number of the interface that connects SwitchA and SwitchB on SwitchA J Authentication mode user name and password Configuration Procedure 1 Log in to SwitchA through the console port For details see Logging In to the Switch Through the Console Interface 2 Set the device name of SwitchA lt Quidway gt system view Quidway sysname SwitchA 3 Configure a management VLAN SwitchA vlan 1 SwitchA vlanl description admin VLAN Issue 02 2012 10 27 Huawei Proprietary and Confidential 34 Copyright Huawei Technologies Co Ltd 2700 amp 83700 Series Ethernet Switches Quick Start 5 Logging in to the Device 4 On SwitchA set the type of the interface that connects SwitchA and SwitchB to trunk Add the interface to the management VLAN in trunk mode SwitchA interface Gigabitethernet 0 0 1 SwitchA GigabitEthernet0 0 1 port link type trunk SwitchA GigabitEthernet0 0 1 port trunk allow pass vlan 1 SwitchA GigabitEthernet0 0 1 quit Configure the management IP address of Switc
33. used Green The power supply is normal Issue 02 2012 10 27 Huawei Proprietary and Confidential 17 Copyright Huawei Technologies Co Ltd S27008 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Two power supply units are installed properly but not switched on The power supply units are switched off The card power and PoE power are abnormal If a single power supply unit is installed the PoE power is out of range If two power supply units are installed the card power or PoE power is out of range The power supply indicator units are not present or the power supply is abnormal when a single power supply unit is used Two power supply units are installed properly but not switched on The power supply units are switched off The card power and PoE power are abnormal If a single power supply unit is installed the PoE power is out of range If two power supply units are installed the card power or PoE power is out of range Issue 02 2012 10 27 Huawei Proprietary and Confidential 18 Copyright Huawei Technologies Co Ltd S27008 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction System status SYS The system is not indicator operating Green The system is not operating properly or is starting Orange The system is performing self check during startup Blinking green The system is operati
34. wing table describes the meanings of indicators Table 2 5 Description of indicators in different modes Ofi STAT The interface is not connected or has been shut down The interface is connected Blinking green The interface is sending or receiving data Issue 02 2012 10 27 Huawei Proprietary and Confidential 11 Copyright Huawei Technologies Co Ltd S27008 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Speed Off The interface is not connected or has been shut down Green The interface speed is 10 100 Mbit s Blinking green The interface speed is 1000 Mbit s PoE Off The interface does not provide remote power Green The interface is providing remote power Blinking green The power of the powered device PD exceeds the power supply capability of the port or exceeds the threshold Figure 2 5 S2710 52P PWR SI indicators Table 2 6 Description of S2710 52P PWR SI indicators 1 Power PWRI Off The power supply indicator units are not present or the power supply is abnormal when a single power supply unit is used Green The power supply is normal Issue 02 2012 10 27 Huawei Proprietary and Confidential 12 Copyright Huawei Technologies Co Ltd S27008 amp S3700 Series Ethernet Switches Quick Start 2 Product Hardware Introduction Two power supply units are installed properly but not switched on The power supply units are switched off
Download Pdf Manuals
Related Search