Sitecom WLR-2001 router
Contents
1. DMZ If you have a client PC that cannot run an Internet application e g Games properly from behind the NAT firewall then you can open up the firewall restrictions to unrestricted two way Internet access by defining a DMZ Host The DMZ function allows you to re direct all packets going to your WAN port IP address to a particular IP address in your LAN The difference between the virtual server and the DMZ function is that the virtual server re directs a particular service Internet application e g FTP websites to a particular LAN client server whereas DMZ re directs all packets regardless of services going to your WAN IP address to a particular LAN client server 300N 3C READY ROUTER uas If you have a local client PC that cannot run an Internet application properly from behind the NAT firewall you can open unrestricted two way Internet access for this client by defining a Virtual DMZ Host Enable DMZ Public IP Address Client PC IP Address Dynamic IP Session 1 Ostatic iP E DMZ table Public IP Address Client PC IP Address Enable DMZ Enable disable DMZ Public IP Address The IP address of the WAN port or any other Public IP addresses given to you by your ISP Client PC IP Address Fill in the IP address of a particular host in your LAN that will receive all the packets originally going to the WAN port Public IP address above Click Apply at the bottom of the screen to sa2. E Qj Local Area Connection Properties Networking Sharing Connect using WP Broadcom 440x 10 100 Integrated Controller confi This connection uses the following items v 0 Client for Microsoft Networks QoS Packet Scheduler v VI B File and Printer Sharing for Microsoft Networks M 4 Intemet Protocol Version 6 TCP IPv6 ivi p TCP IP v vi A Intemet Protoce ler Link Layer Topology Discovery Mapper 1 0 Driver Link Layer Topology Discovery Responder Install d Unin stal Properties Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks ok Cms Internet Protocol Version 4 TCP IPv4 Properties EN General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings 5 Use the following IP address IP address Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server e Select the General tab The WLR 2001 supports DHCP function please select both Obtain an IP address automatically and Obtain DNS server address automatically 8 Bringing up the
3. WLR 2001 300N Wireless 3G Ready Router 802 11 b g n User Manual Revision 1 0 TABLE OF CONTENTS IKEY FEATURES ESS 4 ZPACKAGE CONTENTS iois 5 BSPRODUCT LAYOUT 6 4NETWORK SYSTEM REQUIREMENTS cccssssssssssssssssssssssssecsssssssessssssssscsssssssscsssssessessessnes 8 SWLR 2001 PLACEMEN 8 OSETUP LAN WAN 9 7PC NETWORK ADAPTER SETUP scscsssssssscssssssssssscssessssesssesssseessesssssessesssseessesssseessesseseesees 10 SBRINGING UP THE WLR 2001 eeeeeeeee esee eene etes tn enean tunes statu seas en enses tn sn sens ta sn sens tatu nen 14 9INITIAL SETUP OF THE WLR 2001 eeeeeeeee eese ee entente enata sensn nenas tn tns ens ttn tn sens tn sn sens tn sn nen 14 10CONFIGURATION WIZARD ceste estet tntn sets tatus tna status tns s inen sse inen sss en en ases sos ens sesso senatus 23 HIDMIRUBUCUNIUAMURC eosa 25 I2ZFIREWALL SETTINGS E M P 35 13ADVANCED SETTING cccsssssssssssesscssscsecessssssesecsssssesessssssesesessssesesessssssesesensseesesenseessesensseesess 41 LATO OLBOX SETTINGS R 51 20 Introduction Congratulations on your purchase of the WLR 2001 Wireless Network Broadband Router The WLR 2001 is compliant with 802 11n and up to 6 times faste
4. specified Add Special Application Fill in the Trigger Port Trigger Type Public Port Public Type Public Port and Comment of the setting to be added and then click Add The Special Application setting will be added into the Current Trigger Port Table below If you happen to make a mistake just click Clear and the fields will be cleared Remove If you want to remove Special Application settings from the Current Trigger Port Table select the Special Application settings you want to remove in the table and then click Delete Selected If you want remove all Special Application settings from the table just click the Delete All button Click Reset will clear your current selections ALG You can select applications that need Application Layer Gateway support 200N3G READY ROUTER i i 7 o Choose your language NAT Enable Port forwarding Virtual Server Special Applications Application Layer Gateway a Quality of Service Some applications require special support to function under NAT Please select the applications which you are using DCINENCKENERN MN CO NN FI H323 Support for H323 netmeeting o MMS Support for Microsoft Streaming Media Services protocol m TFTP Support for TFTP o Egg Support for eggdrop bot networks o IRC Allows DCC to work though NAT and connection tracking Fi Amanda Support for Amanda backup tool protocol o Quake3 Support for Quake II
5. NET start NAT k Save J Clear Refresh WLR 2001 Statistics Shows the counters of packets sent and received on WAN LAN amp WLAN 300N3G READY ROUTER esas WIRELESS System Status Device Status Internet Status DHCP Status This page shows the packet counters for transmission and reception regarding to networks Sent Packets 2060 Wireless LAN Received Packets 32834 Sent Packets 4130 Ethernet LA Received Packets 3044 Sent Packets 2367 Ethernet WAN Received Packets 3458 10 Configuration Wizard Click Wizard to configure the router The Setup wizard will now be displayed check that the modem is connected and click Next 300N3C READY ROUTER imaw Choose your language Setup Wizard The Setup Wizard will guide you step by step through a basic configuration procedure Next Select your country from the Country list Select your internet provider Click Next 300N3G READY ROUTER Choose your language v Select your country and ISP ms Country N Service f Depending on the chosen provider you may need to enter your user name and password MAC address or hostname in the following window After you have entered the correct information click Next 300NROUTER eua WIRELESS vance Choose your language Please enter the data which is supplied by your ISP Alleen voor oudere home verbindingen BENNETT cen
6. Once you ve selected the new firmware file click Apply at the bottom of the screen to start the upgrade process Backup Settings The Backup screen allows you to save Backup the router s current configuration settings When you save the configuration setting Backup you can re load the saved configuration into the router through the Restore selection If extreme problems occur you can use the Restore to Factory Defaults selection this will set all configurations to its original default settings e g when you first purchased the router 200N3G READY ROUTER euussup Use BACKUP to save the routers current configuration to a file named config dlf You can use RESTORE to restore the saved configuration Alternatively you can use RESTORE TO FACTORY DEFAULT to force the router to restore the factory default settings Restore To Factory Default Use the Backup tool to save the Broadband router current configuration to a file named config bin on your PC You can then use the Restore tool to restore the saved configuration to the Broadband router Alternatively you can use the Restore to Factory Defaults tool to force the Broadband router to perform a power reset and restore the original factory settings Reset You can reset the router s system should any problem exist The reset function essentially re boots your router s system 200N3G READY ROUTER usssip In the event the system stops responding cor
7. WLR 2001 Connect the supplied power adapter to the power inlet port and connect it to a wall outlet The WLR 2001 automatically enters the self test phase During self test phase the Power LED will be lit continuously to indicate that this product is in normal operation 9 Initial Setup of the WLR 2001 LOGIN procedure 1 OPEN your browser e g Internet Explorer eeed 2 Type http 192 168 0 1 in address bar and press Enter Blank Page Windows Internet Explorer fo cov e htpitse 169 0 1 File Edt View Favorites Took Help WR BE Connecting Connect to 192 168 0 1 The server 192 168 0 1 requires username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection User name fe y Password o 3 Remember my password Cox c 3 Type user name and password default username is admin the password can be found on the backlabel of your router Connect to 192 168 0 1 The server 192 168 0 1 requires a username and password Warning This server is requesting that your username and password be sent in an insecure manner basic without a secure connection User name e admin Password eocce v Remember my password 7 em 4 Click OK 5 You will see the home page of the WLR 2001 200N3G READY ROUTER ixw Fi x Choose your langu
8. port number You can assign priority for each type of application and reserve bandwidth for it The packets of applications with higher priority will always go first Lower priority applications will get bandwidth after higher priority applications get enough bandwidth This can let you have a better experience in using critical real time services like Internet phone video conference etc All the applications not specified by you are classified as rule name Others The rule with a smaller priority number has a higher priority the rule with a larger priority number has a lower priority You can adjust the priority of the rules by moving them up or down 300N3G READY ROUTER usse Quality of Service Quality of Service QoS refers to the capability of a network to provide better service to selected network traffic The primary goal of QoS is to provide priority including dedicated bandwidth controlled jitter and latency required by some real time and interactive traffic and improved loss characteristics Also important is making sure that providing priority for one or more flaws does not make other flows fail Enable QoS Current QoS Table Add Move Up J Move Down J Reset Enable Disable QoS You can check Enable QoS to enable QoS functionality for the WAN port Add a QoS rule into the table Click Add then enter a form of the QoS rule Click Apply after filling out the form the rule
9. same time SSID This is the name of the wireless signal which is broadcasted All the devices in the same wireless LAN should have the same ESSID Channel The channel used by the wireless LAN All devices in the same wireless LAN should use the same channel Advanced Settings This tab allows you to set the advanced wireless options The options included are Authentication Type Fragment Threshold RTS Threshold Beacon Interval and Preamble Type You should not change these parameters unless you know what effect the changes will have on the router WIRELESS EE 2345 256 2346 RTS Threshold 2347 1 2347 Beacon Interv 00 20 1024 ms 4 255 Preece Auto v DES As v TELCO Auto 20 40 MHZ O 20 MHZ ae Long Preamble short Preamble GETTEN ASS Enable Disable Pees Auto O Always O None eerie 100 v LULE Enable Disable 200N3G READY ROUTER euzssuip These settings are only for more technically advanced users who have a sufficient knowledge about wireless LAN These settings should not be changed unless you know what effect the changes will have on your Broadband router CDCR Open System O Shared Key O Auto Authentication Type There are two authentication types Open System and Shared Key When you select Open System wireless stations can associate with this wireless router without WEP encryption When you select Shared Key you should also se
10. will be added into the table Remove QoS rules from the table If you want to remove QoS rules from the table select the QoS rules you want to remove in the table and then click Delete Selected If you want remove all QoS rules from the table just click the Delete All button Clicking Reset will clear your current selections Edit a QoS rule Select the rule you want to edit and click Edit then enter the detail form of the QoS rule Click Apply after editing the form and the rule will be saved Adjust QoS rule priority You can select the rule and click Move Up to make its priority higher You also can select the rule and click Move Down to make its priority lower 14 TOOLBOX Settings Password change options You can change the password required to log into the broadband router s system web based management By default the password is admin Passwords can contain O to 12 alphanumeric characters and are case sensitive 300N3C READY ROUTER icz d Choose your language Password You can change the password which is required to log on to the router By default the password is admin Passwords can contain 0 to 30 alphanumeric characters and are case sensitive Current Password l New Password Confirm Password Current Password Fill in the current password to allow changing to a new password New Password Enter your new password Confirmed Password Enter your new password again f
11. will be useful but WITHOUT ANY LIABILITY OF OR ANY WARRANTY FROM THE LICENSOR Appendix B GNU GENERAL PUBLIC LICENSE Version 2 June 1991 Copyright C 1989 1991 Free Software Foundation Inc 59 Temple Place Suite 330 Boston MA 02111 1307 USA Everyone is permitted to copy and distribute verbatim copies of this license document but changing it is not allowed Preamble The licenses for most software are designed to take away your freedom to share and change it By contrast the GNU General Public License is intended to guarantee your freedom to share and change free software to make sure the software is free for all its users This General Public License applies to most of the Free Software Foundation s software and to any other program whose authors commit to using it Some other Free Software Foundation software is covered by the GNU Library General Public License instead You can apply it to your programs too When we speak of free software we are referring to freedom not price Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software and charge for this service if you wish that you receive source code or can get it if you want it that you can change the software or use pieces of it in new free programs and that you know you can do these things To protect your rights we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrende
12. you may at your option offer warranty protection in exchange for a fee 2 You may modify your copy or copies of the Program or any portion of it thus forming a work based on the Program and copy and distribute such modifications or work under the terms of Section 1 above provided that you also meet all of these conditions a You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change b You must cause any work that you distribute or publish that in whole or in part contains or is derived from the Program or any part thereof to be licensed as a whole at no charge to all third parties under the terms of this License c If the modified program normally reads commands interactively when run you must cause it when started running for such interactive use in the most ordinary way to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty or else saying that you provide a warranty and that users may redistribute the program under these conditions and telling the user how to view a copy of this License Exception if the Program itself is interactive but does not normally print such an announcement your work based on the Program is not required to print an announcement These requirements apply to the modified work as a whole If identifiable sections of that work are not derived from the Program and can be reasonably consid
13. 2001 on a desk or other flat surface or you can mount it on a wall For optimal performance place your Wireless Broadband Router in the center of your office or your home in a location that is away from any potential source of interference such as a metal wall or microwave oven This location must be close to a power connection and your ADSL Cable modem in case you re using the WAN port 6 Setup LAN WAN WAN connection 7 PC Network Adapter setup Windows XP e Enter Start Menu gt select Control panel gt select Network amp Network Connections F Fie Edit View Favorites Tools Advanced Help Q O B p E Foes ET Address B Network Connections Internet Gateway Network Tasks Internet Connection E Create a new connection f Setup a home or small 1 office network Change Windows Firewall settings LAN or High Speed Internet Bx Wireless Network Connection rae Local Area Connection See Also a 4 Network Troubleshooter 3 Other Places a Control Panel 9 My Network Places e Select Local Area Connection icon gt select properties ocal Area Connection Connected Firew Disable Status Repair Bridge Connections Create Shortcut Delete Rename Properties e Select Internet Protocol TCP IP gt Click Properties 4 Local Area Connection Properties M Network Monitor Driver f Micros
14. 4 You may not copy modify sublicense or distribute the Program except as expressly provided under this License Any attempt otherwise to copy modify sublicense or distribute the Program is void and will automatically terminate your rights under this License However parties who have received copies or rights from you under this License will not have their licenses terminated so long as such parties remain in full compliance 5 You are not required to accept this License since you have not signed it However nothing else grants you permission to modify or distribute the Program or its derivative works These actions are prohibited by law if you do not accept this License Therefore by modifying or distributing the Program or any work based on the Program you indicate your acceptance of this License to do so and all its terms and conditions for copying distributing or modifying the Program or works based on it 6 Each time you redistribute the Program or any work based on the Program the recipient automatically receives a license from the original licensor to copy distribute or modify the Program subject to these terms and conditions You may not impose any further restrictions on the recipients exercise of the rights granted herein You are not responsible for enforcing compliance by third parties to this License 7 If as a consequence of a court judgment or allegation of patent infringement or for any other reason not li
15. I Arena connection tracking and nat m Talk Allows netfilter to track talk connections o IPsec Support for IPsec passthrough o FTP Support for FTP Enable select enable Application Layer Gateway then the router will let the selected application correctly pass through the NAT gateway UPNP With UPnP all PCs in you Intranet will discover this router automatically so you don t have to configure your PC and it can easily access the Internet through this router 200N3G READY ROUTER eus Universal Plug and Play is designed to support zero configuration invisible networking and automatic discovery for a range of device from a wide range of vendors With UPnP a device can dynamically join a network obtain an IP address and learn about the presence and capabilities of other devices all automatically Devices can subsequently communicate with each other directly UPnP Enable Qbisable UPnP Feature You can enable or Disable the UPnP feature here After you enable the UPnP feature all client systems that support UPnP like Windows XP can discover this router automatically and access the Internet through this router without having to configure anything The NAT Traversal function provided by UPnP can let applications that support UPnP connect to the internet without having to configure the virtual server sections QoS QoS can let you classify Internet application traffic by source destination IP address and
16. LAN The authentication is processed by a RADIUS server This mode only authenticates users by IEEE 802 1x but it does not encrypt the data during communication Iv Enable 802 1x Authentication ECIETIEES snows sever ron IDA L lt Apply Cancel WEP When you select 64 bit or 128 bit WEP key you have to enter WEP keys to encrypt data You can generate the key by yourself and enter it You can enter four WEP keys and select one of them as a default key Then the router can receive any packets encrypted by one of the four keys oe ENNCTNES or oo Key Length You can select the WEP key length for encryption 64 bit or 128 bit The larger the key will be the higher level of security is used but the throughput will be lower Key Format You may select ASCII Characters alphanumeric format or Hexadecimal Digits in the A F a f and 0 9 range to be the WEP Key Keyl Key4 The WEP keys are used to encrypt data transmitted in the wireless network Use the following rules to setup a WEP key on the device 64 bit WEP input 10 digits Hex values in the A F a f and 0 9 range or 5 digit ASCII character as the encryption keys 128 bit WEP input 26 digit Hex values in the A F a f and 0 9 range or 13 digit ASCII characters as the encryption keys Click lt Apply gt at the bottom of the screen to save the above configurations You can now configure other sections by choosing Continue o
17. MS EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES END OF TERMS AND CONDITIONS
18. age You can use the Status page to monitor the connection status for the WAN LAN interfaces firmware and hardware version numbers any illegal attempts to access your network and information on all DHCP client PCs currently connected to your network System onn 3G Wireless Router Boot Code Version 1 0 Runtime Code Version 1 0 The System status section allows you to monitor the current status of your router the UP time hardware information serial number as well as firmware version information is displayed here LAN settings The LAN tab gives you the opportunity to change the IP settings of the WLR 2001 300N 3C READY ROUTER usse Choose your language Y DHCP Server You can enable the Broadband routers DHCP server to dynamically allocate IP Addresses to your LAN client PCs The broadband router must k have an IP Address for the Local Area Networl LAN IP Enid s DHCP Server ra Click lt Apply gt at the bottom of this screen to save any changes IP address 192 168 0 1 It is the router s LAN IP address Your LAN clients default gateway IP address IP Subnet Mask 255 255 255 0 Specify a Subnet Mask for your LAN segment 802 1d Spanning Tree is Disabled by default If the 802 1d Spanning Tree function is enabled this router will use the spanning tree protocol to prevent network loops DHCP Server Enabled by default You can enable or disable the DHCP
19. e Previous Apply Cancel si Choose your language Please enter the data which is supplied by your ISP PPP over Ethernet 1452 512 MTU Value lt 1492 Connection Type Keepconnecion Connect Disconnect Idle Time 0 1 1000 Minutes Previous Apply Cancel Click APPLY to complete the configuration 11 Wireless Settings You can set parameters that are used for the wireless stations to connect to this router The parameters include Mode ESSID Channel Number and Associated Client Wireless Function WIRELESS 300N3C READY ROUTER uas Choose your language Enable Basic The gateway can be quickly configured as a wireless access point for roaming clients by setting the SSID and channel number It also supports data encryption and client filtering Enable or disable Wireless module function Enable O Disable Enable or Disable Wireless function here Click Apply and wait for module to be ready amp loaded Basic Settings 300N3G READY ROUTER usse This page allows you to define ESSID and Channel for the wireless connection These parameters are used for the wireless stations to connect to the Access Point MEET 202600 oT Mode Allows you to set the AP to AP Station Bridge or WDS mode Band Allows you to set the AP fixed at 802 11b or 802 11g mode You can also select B G mode to allow 80211b and 802 11g clients at the
20. e applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License The Program below refers to any such program or work and a work based on the Program means either the Program or any derivative work under copyright law that is to say a work containing the Program or a portion of it either verbatim or with modifications and or translated into another language Hereinafter translation is included without limitation in the term modification Each licensee is addressed as you Activities other than copying distribution and modification are not covered by this License they are outside its scope The act of running the Program is not restricted and the output from the Program is covered only if its contents constitute a work based on the Program independent of having been made by running the Program Whether that is true depends on what the Program does 1 You may copy and distribute verbatim copies of the Program s source code as you receive it in any medium provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty keep intact all the notices that refer to this License and to the absence of any warranty and give any other recipients of the Program a copy of this License along with the Program You may charge a fee for the physical act of transferring a copy and
21. e wireless router supports two types of WPS WPS via Push Button and WPS via PIN code If you want to use the Push Button you have to push a specific button on the wireless client or in the utility of the wireless client to start the WPS mode and switch the wireless router to WPS mode You can simply push the WPS button of the wireless router or click the Start to Process button in the web configuration interface If you want to use the PIN code you have to know the PIN code of the wireless client and switch it to WPS mode then fill in the PIN code of the wireless client through the web configuration interface of the wireless router 300N3C READY ROUTER ic Choose yourlanguage ense asic advanced secunty net wes IEEE Enable Wi Fi Protected Setup Information Authentication Mode e pre shared key MEI cc Startto Process WPS Check the box to enable WPS function and uncheck it to disable the WPS function WPS Current Status If the wireless security encryption function of this wireless router is properly set you ll see a Configured message here Otherwise you ll see UnConfigured Self Pin Code This is the WPS PIN code of the wireless router You may need this information when connecting to other WPS enabled wireless devices SSID This is the network broadcast name SSID of the router Authentication Mode It shows the active authentication mode for the wireless connectio
22. eless network enabling this feature is recommended Disabling Broadcast ESSID can provide better security CTS Protection It is recommended to enable the protection mechanism This mechanism can decrease the rate of data collision between 802 11b and 802 11g wireless stations When the protection mode is enabled the throughput of the AP will be a little lower due to a lot of frame network that is transmitted TX Power can be set to a bare minimum or maximum power WMM Wi Fi Multi Media if enabled supports QoS for experiencing better audio video and voice in applications Security This Access Point provides complete wireless LAN security functions included are WEP IEEE 802 11x IEEE 802 11x with WEP WPA with pre shared key and WPA with RADIUS With these security functions you can prevent your wireless LAN from illegal access Please make sure your wireless stations use the same security function and are setup with the same security key Disable When you choose to disable encryption it is very insecure to operate the WLR 2001 This page allows you setup the wireless security Turn on WEP or WPA by using Encryption Keys could prevent any unauthorized access to your wireless network I3 ei Disable hd T Enable 802 1x Authentication Apply Cancel Enable 802 1x Auth IEEE 802 1x is an authentication protocol Every user must use a valid account to login to this Access Point before accessing the wireless
23. ered independent and separate works in themselves then this License and its terms do not apply to those sections when you distribute them as separate works But when you distribute the same sections as part of a whole which is a work based on the Program the distribution of the whole must be on the terms of this License whose permissions for other licensees extend to the entire whole and thus to each and every part regardless of who wrote it Thus it is not the intent of this section to claim rights or contest your rights to work written entirely by you rather the intent is to exercise the right to control the distribution of derivative or collective works based on the Program In addition mere aggregation of another work not based on the Program with the Program or with a work based on the Program on a volume of a storage or distribution medium does not bring the other work under the scope of this License 3 You may copy and distribute the Program or a work based on it under Section 2 in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following a Accompany it with the complete corresponding machine readable source code which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or b Accompany it with a written offer valid for at least three years to give any third party for a charge no more than your cost of phy
24. ge System Status DHCP Server Device Status Internet Status DHCP Status Statistics Internet Status This page displays whether the WAN port is connected to a Cable DSL or 3G connection It also displays the router s WAN IP address Subnet Mask and ISP Gateway as well as MAC address the Primary DNS Press Renew button to renew your WAN IP address 300N3C READY ROUTER inap DHCP Server Internet Status DHCP Status View the current internet connection status and related information Mn IP Address ed 0 28 27 52 00 58 DHCP Client Status DHCP This page shows all DHCP clients LAN PCs currently connected to your network The table shows the assigned IP address MAC address and expiration time for each DHCP leased client Use the Refresh button to update the available information You can check Enable Static DHCP IP It is possible to add more static DHCP IP s They are listed in the table Current Static DHCP Table IP can be deleted at will from the table Click apply button to save the changed configuration 300N3C READY ROUTER imaw This table shows the assigned IP address MAC address and expiration time for each DHCP leased client 192 168 0 100 00 10 23 AS B8 4C Forever Enable Static DHCP IP Add Reset Current Static DHCP Table Reset Apply J Cancel J WLR 2001 Log View the operation log of the WLR 2001 This page shows the current system log of t
25. guage v Remote The remote management function allows you to designate a host from the Internet to have management configuration access to the router from a remote site Enter the designated host IP Address in the Host IP Address field mer pos Apply Host Address This is the IP address of the host in the Internet that will have management configuration access to the Broadband router from a remote site If the Host Address is left 0 0 0 0 this means anyone can access the router s web based configuration from a remote location providing they know the password Port The port number of the remote management web interface Enabled Select Enabled to enable the remote management function Click lt Apply gt at the bottom of the screen to save the above configurations Firmware Upgrade This page allows you to upgrade the router s firmware 200N3G READY ROUTER This tool allaws you to upgrade the Routers firmware Browse to and select the upgrade file and click APPLY You will be prompted to confirm the rade upg Browse Firmware Upgrade This tool allows you to upgrade the Broadband router s system firmware To upgrade the firmware of your Broadband router you need to download the firmware file to your local hard disk and enter that file name and path in the appropriate field on this page You can also use the Browse button to find the firmware file on your PC
26. he Broadband router It displays any event occurred after system start up At the bottom of the page the system log can be saved Save to a local file for further processing or the system log can be cleared Clear or it can be refreshed Refresh to get the most updated information When the system is powered down the system log will disappear if not saved to a local file 200N3G READY ROUTER usu 4 09 06 02 SYSTEM NTP Local time 2009 06 04 09 06 Jun 4 09 06 02 SYSTEM NTP Daylight saving status Disable Jun 4 09 06 02 SYSTEM NTP Time zone 40 0 Greenvich Mean Time Dublin Edinburgh Lisbon London day 1 00 16 38 SYSTEM UPnP Stopping day 1 00 16 38 SYSTEM NTP start NTP Client day 1 00 16 38 SYSTEM DNS start DNS Proxy day 1 00 16 36 SYSTEM NET start Firewall a day 1 00 16 36 SYSTEM NET start NAT day 1 00 16 36 SYSTEM NET stop Firewall day 1 00 16 36 SYSTEM NET stop NAT day 1 00 16 36 SYSTEM WAN IP changed restart services day 1 00 16 36 SYSTEM WAN New IP 192 168 1 68 day 1 00 16 31 SYSTEM QoS Stopping day 1 00 11 08 SYSTEM DHCP Server Sending ACK of 192 168 0 100 day 1 00 00 07 SYSTEM WAN No PHY Link day 1 00 00 07 SYSTEM WAN start DHCP mode day 1 00 00 06 SYSTEM WAN stop DHCP mode day 1 00 00 05 SYSTEM WAN stop DHCP mode day 1 00 00 03 SYSTEM HTTP start day 1 00 00 02 SYSTEM NET start Firewall day 1 00 00 02 SYSTEM
27. k for permission For software which is copyrighted by the Free Software Foundation write to the Free Software Foundation we sometimes make exceptions for this Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally NO WARRANTY 11 BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE THERE IS NO WARRANTY FOR THE PROGRAM TO THE EXTENT PERMITTED BY APPLICABLE LAW EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND OR OTHER PARTIES PROVIDE THE PROGRAM AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU SHOULD THE PROGRAM PROVE DEFECTIVE YOU ASSUME THE COST OF ALL NECESSARY SERVICING REPAIR OR CORRECTION 12 IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER OR ANY OTHER PARTY WHO MAY MODIFY AND OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE BE LIABLE TO YOU FOR DAMAGES INCLUDING ANY GENERAL SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRA
28. ltering Table up to 20 computers 9 Deny Odallow Apply Cancel J Deny If you select Deny then all clients will be allowed to access Internet accept for the clients in the list below Allow If you select Allow then all clients will be denied to access Internet accept for the PCs in the list below Filter client PCs by IP Fill in IP Filtering Table to filter PC clients by IP Add PC You can click Add PC to add an access control rule for users by IP addresses Remove PC If you want to remove some PCs from the IP Filtering Table select the PC you want to remove in the table and then click Delete Selected If you want to remove all PCs from the table just click the Delete AII button Filter client PC by MAC Check Enable MAC Filtering to enable MAC Filtering Add PC Fill in Client PC MAC Address and Comment of the PC that is allowed to access the Internet and then click Add If you find any typo before adding it and want to retype again just click Reset and the fields will be cleared Remove PC If you want to remove some PC from the MAC Filtering Table select the PC you want to remove in the table and then click Delete Selected If you want to remove all PCs from the table just click the Delete AII button If you want to clear the selection and re select again just click Reset Click Apply at the bottom of the screen to save the above configuration URL block You can block acce
29. mited to patent issues conditions are imposed on you whether by court order agreement or otherwise that contradict the conditions of this License they do not excuse you from the conditions of this License If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations then as a consequence you may not distribute the Program at all For example if a patent license would not permit royalty free redistribution of the Program by all those who receive copies directly or indirectly through you then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program If any portion of this section is held invalid or unenforceable under any particular circumstance the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system it is up to the author donor to decide if he or she is willing to distribute software through any other sy
30. n Passphrase Key It shows the passphrase key that is randomly generated by the wireless router during the WPS process You may need this information when using a device which doesn t support WPS WPS via Push Button Press the button to start the WPS process The router will wait for the WPS request from the wireless devices within 2 minutes WPS via PIN You can fill in the PIN code of the wireless device and press the button to start the WPS process The router will wait for the WPS request from the wireless device within 2 minutes 12 Firewall Settings The Broadband router provides extensive firewall protection by restricting connection parameters thus limiting the risk of hacker attacks and defending against a wide array of common Internet attacks However for applications that require unrestricted access to the Internet you can configure a specific client server as a Demilitarized Zone DMZ Note To enable the Firewall settings select Enable and click Apply 300N3C READY ROUTER ic Choose yourlanguage The Broadband router provides extensive firewall protection by restricting connection parameters thus limiting the risk of a hacker attack and defending against a wide array of common attacks However for applications that require unrestricted access to the Internet you can configure a specific client server as a Demilitarized Zone DMZ Enable or disable Firewall module function Enable O Disable Apply
31. oft TCP IP version 6 Internet Protocol TCP IP You can get IP settings assigned automatically if your network supports this capability Nes you need to ask your network administrator for IP settings Preferred DNS server Altemate DNS server e Select the General tab a The WLR 2001 supports DHCP function please select both Obtain an IP address automatically and Obtain DNS server address automatically Windows Vista Seven Enter Start Menu gt select Control panel gt select View network status and tasks gt select Manage network connections r a QOO d jd Network and muc Network Connections gt Y 5 Name Status Device Name Connectivity Network Category Owner LAN or High Speed Internet 2 L Local Area Connection i Wireless Network Connection Network 2 r Not connected Broadcom 440x 10 100 Integ 9 il Broadcom 802 11g Network Select Local Area Connection icon gt select properties KJ ge Network and Internet Network Connections gt By Organize m Views v Disable this network device Bay Name Status Device Name Connectivity Netwc LAN or High Speed Internet 2 a Local Area Connection Wireless Network Co w Network 2 z ed GE Broadcom 440x10 Disable 211g N Status Diagnose Bridge Connections Create Shortcut Delete Rename Properties e Select Internet Protocol Version 4 TCP IPv4 gt Click Properties
32. onnect your PC s or network devices to this port WAN Blue Connect your ADSL Cable modem to this port USB Connect your 3G USB modem to this port Back label The back label describes the IP address login details SSID security code and WPS button functionality To access the router configuration type the following IP address in your internet browser 192 168 0 1 Username admin Password To make a wireless connection with this router choose the network Serial No WPA2 code ac WPS mode 0 sec Reset LAN LANWAN US Press 15 sec Factory default Description WPS BUTTON Press 2 seconds for WPS mode Press 10 seconds to reset the router Press 15 Seconds to reset the router to factory defaults LED Definition From left to right Port Description LAN Blue Shows the cable is connected WiFi Blue Shows WiFi activity and WPS riens Gus vai EA Shows the device is turned on 4 Network System Requirements To begin using the WLR 2001 make sure you meet the following as minimum requirements e PC Notebook e Operating System Microsoft Windows XP 2000 VISTA e 1 Free Ethernet port e Wi Fi card USB dongle 802 11 b g n optional e External xDSL ADSL or Cable modem with an Ethernet port RJ 45 or a 3G USB modem e PC with a Web Browser Internet Explorer Safari Firefox Opera e Ethernet compatible CAT5 cables 5 WLR 2001 Placement You can place the WLR
33. or verification purposes Click Apply at the bottom of the screen to save the above configurations Time Zone The Time Zone allows your router to base its time on the settings configured here which will affect functions such as Log entries and Firewall settings 200N3G READY ROUTER euussuip Timezone Set the time zone of the Broadband router This information is used for log entries and firewall settings ey ov Time Dublin Edinburgh Lisbon London Enable From To Set Time Zone Select the time zone of the country you are currently in The router will set its time based on your selection Time Server Address You can set an NTP server address Enable Daylight Savings The router can also take Daylight savings into account If you wish to use this function you must check tick the enable box to enable your daylight saving configuration below Start Daylight Savings Time Select the period in which you wish to start daylight Savings Time End Daylight Savings Time Select the period in which you wish to end daylight Savings Time Click Apply at the bottom of the screen to save the above configurations Remote Management The remote management function allows you to designate a host in the Internet the ability to configure the Broadband router from a remote site Enter the designated host IP Address in the Host IP Address field 300N3C READY ROUTER uas WIRELESS Choose your lan
34. r choose Apply to apply the settings and reboot the device WPA Pre shared Key Wi Fi Protected Access WPA is an advanced security standard You can use a pre shared key to authenticate wireless stations and encrypt data during communication It uses TKIP or CCMP AES to change the encryption key frequently So the encryption key is not easy to be cracked by hackers This is the best security available Encryption WPA pre shared key GEILE WPA TKIP C wPA2 AES C WPA2 Mixed Pre shared Key Type Passphrase gt Pre sharedKey as Apply Cancel WPA X D Q 7 Wi Fi Protected Access WPA is an advanced security standard You can use an external RADIUS server to authenticate wireless stations and provide the session key to encrypt data during communication It uses TKIP or CCMP AES to change the encryption key frequently Press Apply button when you are done Encryption wPARaDUS g DLL WITIXE wPACKIP C WPAZ AES C WPA2 Mixed RADIUS Server IP Address I 3 RADIUS Server Port ec RADIUS Server Password Cancel ACL This wireless router supports MAC Address Control which prevents unauthorized clients from accessing your wireless network 300N 3C READY ROUTER inaw Choose your language v For security reason the Access Point features MAC Address Filtering which only allows authorized MAC Addresses to associate with the Access Point MAC Address Fil
35. r than standard 802 11g based routers while still being compatible with 802 11g amp 802 11b gadgets The WLR 2001 is not only a Wireless Access Point but also doubles as a 2 port full duplex Switch that connects your wired Ethernet devices together At 300 Mbps wireless transmission rate the Access Point built into the Router uses advanced MIMO Multi Input Multi Output technology to transmit multiple steams of data in a single wireless channel giving you seamless access to multimedia content Robust RF signal travels farther eliminates dead spots and extends network range For data protection and privacy the WLR 2001 encodes all wireless transmissions with WEP WPA and WPA2 encryption With the inbuilt DHCP Server amp powerful SPI firewall the WLR 2001 protects your computers against intruders and most known Internet attacks but provides safe VPN pass through With incredible speed and QoS function of 802 11n the WLR 2001 is ideal for media centric applications like streaming video gaming and VoIP telephony to run multiple media intense data streams through the network at the same time with no degradation in performance Besides it also provides a USB port which let you easily share a 3G UMTS modem 1 Key Features Features Advantages Incredible Data Rate up to 300Mbps Heavy data payloads such as MPEG video streaming IEEE 802 11n compliant and backwards compatible with 802 11b g Fully Interoperable wi
36. r the rights These restrictions translate to certain responsibilities for you if you distribute copies of the software or if you modify it For example if you distribute copies of such a program whether gratis or for a fee you must give the recipients all the rights that you have You must make sure that they too receive or can get the source code And you must show them these terms so they know their rights We protect your rights with two steps 1 copyright the software and 2 offer you this license which gives you legal permission to copy distribute and or modify the software Also for each author s protection and ours we want to make certain that everyone understands that there is no warranty for this free software If the software is modified by someone else and passed on we want its recipients to know that what they have is not the original so that any problems introduced by others will not reflect on the original authors reputations Finally any free program is threatened constantly by software patents We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses in effect making the program proprietary To prevent this we have made it clear that any patent must be licensed for everyone s free use or not licensed at all The precise terms and conditions for copying distribution and modification follow TERMS AND CONDITIONS FOR COPYING DISTRIBUTION AND MODIFICATION 0 This Licens
37. re direct a particular range of service port numbers from the Internet WAN Port to a particular LAN IP address It helps you to host servers behind the router NAT firewall 300N3C READY ROUTER icz Port forwarding Entries in this table allow you to automatically redirect common network services to a specific PC ED the NAT firewall These settings are only necessary if you wish to hast some sort of server like a web server or mail server on the local network Enable Port Forwarding Both Current Port Forwarding Table Enable Port Forwarding Enable Port Forwarding Private IP This is the private IP of the server behind the NAT firewall Type This is the protocol type to be forwarded You can choose to forward TCP or UDP packets only or select both to forward both TCP and UDP packets Port Range The range of ports to be forward to the private IP Comment description of this setting Add Port Forwarding Fill in the Private IP Type Port Range and Comment of the setting to be added and then click Add Then this Port Forwarding setting will be added into the Current Port Forwarding Table below Remove Port Forwarding If you want to remove a Port Forwarding setting from the Current Port Forwarding Table select the Port Forwarding setting that you want to remove in the table and then click Delete Selected If you want to remove all Port Forwarding settings from
38. rectly or stops functioning you can perform a reset Your settings will not be changed To perform the reset click on the APPLY button You will be asked to confirm your decision The reset will be completed when the LED Power light stops blinking Apply Click lt Apply gt at the bottom of the screen to save the above configurations DDNS DDNS allows you to map the static domain name to a dynamic IP address You must get an account password and your static domain name from the DDNS service providers This router supports DynDNS TZO and other common DDNS service providers 300N3C READY ROUTER uas Choose your language v DDNS allows users to map a static domain name to a dynamic IP address You must get an account password and your static domain name from the DDNS service provider Pn lt i 1 Apply Cancel Enable Disable Enable or disable the DDNS function of this router Provider Select a DDNS service provider Domain name Fill in your static domain name that uses DDNS Account E mail The account that your DDNS service provider assigned to you Password Key The password you set for the DDNS service account above Click Apply at the bottom of the screen to save the above configurations Parts of the firmware of the WLR 2001 Wireless Broadband router are subject to the GNU general public license Appendix A Licensing Information This product includes third pa
39. rty software licensed under the terms of the GNU General Public License vou can modify or redistribute this free software under the terms of the GNU General Public License Please see Appendix B for the exact terms and conditions of this license Specifically the following part of this product is subject to the GNU GPL Package name Source amp Bee et www kernel org 2 Iptables v1 3 5 www netfilter org 3 Bridge utils v1 2 bridge sourceforge net 4 Busybox v1 7 5 www busybox net 5 Rp pppoe v3 8 freshmeat net projects rp pppoe 6 Pptp client v1 7 1 pptpclient sourceforge net Z Ppp v2 4 3 ppp samba org 8 Udhcp v0 9 9 pre udhcp busybox net 9 iproute2 v2 6 16 060323 www linux foundation org en Net Iproute2 10 Dnsmasq v2 39 www thekelleys org uk dnsmasq doc html 11 Ez ipupdate v3 0 11b8 ez ipupdate com 12 HBUpRB V1 6 0 upnp sourceforge net 13 Wireless tools v28 RaLink SDK 3 1 0 0 14 U boot v1 1 3 RaLink SDK 3 1 0 0 15 gcc 3 3 6 RaLink SDK 3 1 0 0 16 Uclibc 0 9 29 RaLink SDK 3 1 0 0 Availability of source code Sitecom Europe BV has made available the full source code of the GPL licensed software including any scripts to control the compilation and installation of the object code in the driver section of this product No Warranty The free software included in this product is distributed in the hope that it
40. server When DHCP is disabled no IP addresses are assigned to clients and you have to use static IP addresses When DHCP server is enabled your computers will be assigned an IP address automatically until the lease time expires Lease Time Forever In the Lease Time setting you can specify the time period that the DHCP lends an IP address to your LAN clients The DHCP will change your LAN client s IP address when this time threshold period is reached IP Address Pool You can select a particular IP address range for your DHCP server to issue IP addresses to your LAN Clients Note default IP range 192 168 0 100 192 168 0 200 If you want your PC s to have a static fixed IP address then you ll have to choose an IP address outside this IP address Pool Domain Name You can specify a Domain Name for your LAN or just keep the default sitecomwlr2001 Device Status View the Broadband router s current configuration settings Device Status displays the configuration settings you ve configured in the Wizard Basic Settings Wireless Settings section View the current setting status of this device Mode EI EXE sitecoms5201A0 Channel 11 Ts TIAE WPA2 pre shared key Pa m Associated Clients o EXE 00 88 97 52 01 40 LAN Configuration Cobre 192 168 0 1 Sau Cee 255 255 255 0 Die rr Ed Enabled iano tite 00 BB 97 52 01 A0 200N3G READY ROUTER isaw s li 5 i j Se 5 Choose your langua
41. sically performing source distribution a complete machine readable copy of the corresponding source code to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange or c Accompany it with the information you received as to the offer to distribute corresponding source code This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer in accord with Subsection b above The source code for a work means the preferred form of the work for making modifications to it For an executable work complete source code means all the source code for all modules it contains plus any associated interface definition files plus the scripts used to control compilation and installation of the executable However as a special exception the source code distributed need not include anything that is normally distributed in either source or binary form with the major components compiler kernel and so on of the operating system on which the executable runs unless that component itself accompanies the executable If distribution of executable or object code is made by offering access to copy from a designated place then offering equivalent access to copy the source code from the same place counts as distribution of the source code even though third parties are not compelled to copy the source along with the object code
42. ss to some Web sites from particular PCs by entering a full URL address or just keywords of the Web site 200N3G READY ROUTER usui URL block You can block access to certain Web sites for a particular PC by entering either a full URL address or just a keyword of the Web site Enable URL Blocking oT Current URL Blocking Table aeey Enable URL Blocking Enable disable URL Blocking Add URL Keyword Fill in URL Keyword and then click Add You can enter the full URL address or the keyword of the web site you want to block Remove URL Keyword If you want to remove some URL keywords from the Current URL Blocking Table select the URL keyword you want to remove in the table and then click Delete Selected If you want remove all URL keywords from the table just click Delete All button If you want to clear the selection and re select again just click Reset Click Apply at the bottom of the screen to save the above configurations 13 Advanced Settings Network Address Translation NAT allows multiple users at your local site to access the Internet through a single Public IP Address or multiple Public IP Addresses NAT provides Firewall protection from hacker attacks and has the flexibility to allow you to map Private IP Addresses to Public IP Addresses for key services such as Websites and FTP Select Disable to disable the NAT function Port Forwarding Port Forwarding allows you to
43. stem and a licensee cannot impose that choice This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License 8 If the distribution and or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries so that distribution is permitted only in or among countries not thus excluded In such case this License incorporates the limitation as if written in the body of this License 9 The Free Software Foundation may publish revised and or new versions of the General Public License from time to time Such new versions will be similar in spirit to the present version but may differ in detail to address new problems or concerns Each version is given a distinguishing version number If the Program specifies a version number of this License which applies to it and any later version you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation If the Program does not specify a version number of this License you may choose any version ever published by the Free Software Foundation 10 If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different write to the author to as
44. tering Table Enable Wireless Access Control DEDE MAC address Comment Apply Enable wireless access control Enables the wireless access control function Adding an address into the list Enter the MAC Address and Comment of the wireless station to be added and then click Add The wireless station will now be added into the Current Access Control List below If you are having any difficulties filling in the fields just click Clear and both MAC Address and Comment fields will be cleared Remove an address from the list If you want to remove a MAC address from the Current Access Control List select the MAC address that you want to remove in the list and then click Delete Selected If you want to remove all the MAC addresses from the list just click the Delete All button Click Reset will clear your current selections Click Apply at the bottom of the screen to save the above configurations You can now configure other sections by choosing Continue or choose Apply to apply the settings and reboot the device WPS Wi Fi Protected Setup WPS is the simplest way to establish a connection between the wireless clients and the wireless router You don t have to select the encryption mode and fill in a long encryption passphrase every time when you try to setup a wireless connection You only need to press a button on both wireless client and wireless router and WPS will do the rest for you Th
45. th IEEE 802 11b IEEESO2 11g compliant devices with legacy protection USB port for 3G USB modem Wireless internet everywhere even without broadband availability Four 10 100 Mbps Fast Switch Ports Auto Crossover Scalability extend your network Firewall supports Virtual Server Mapping DMZ IP Filter ICMP Blocking SPI Avoids the attacks of Hackers or Viruses from Internet Support 802 1x authenticator 802 11i WPA WPA2 AES VPN pass through Provide mutual authentication Client and dynamic encryption keys to enhance security WDS Wireless Distribution System Make wireless AP and Bridge mode simultaneously as a wireless repeater Theoretical wireless signal rate based on IEEE standard of 802 11a b g n chipset used Actual throughput may vary Network conditions and environmental factors lower actual throughput rate All specifications are subject to change without notice 2 Package Contents Open the package carefully and make sure that none of the items listed below are missing Do not discard the packing materials in case of return the unit must be shipped back in its original package WLR 2001 Router 220V 240V Power Adapter Quick Install Guide CD User s Manual Warranty card UTP cable Dit e pes gue ups 3 Product Layout Port Power connector Description Connect the 12V DC adapter to this port LAN Yellow C
46. the outbound port protocol is TCP UDP or both Public Port Enter the In coming Inbound port or port range for this type of application e g 2300 2400 47624 200N3G READY ROUTER usui Some applications require multiple connections such as Internet gaming video conferencing Internet telephony and others These applications cannot work when Network Address Translation NAT is enabled If you need to run applications that require multiple connections specify the port normally associated with an application in the Trigger Port field select the protocol type as TCP or UDP then enter the public ports associated with the trigger part to open them for inbound traffic Enable Trigger Port mese eem Publie Port Publictype L as Ir L j SS SSS Both Both Popular applications Selectan application x Add Current Trigger Port Table oer ee E Public Port ID Public Type Select the Inbound port protocol type TCP UDP or both Comment The description of this setting Popular applications This section lists the more popular applications that require multiple connections Select an application from the Popular Applications selection Once you have selected an application select a location 1 10 in the Copy to selection box and then click the Copy to button This will automatically list the Public Ports required for this popular application in the location 1 10 you
47. the table just click Delete All button Click Reset will clear your current selections Virtual Server Use the Virtual Server function when you want different servers clients in your LAN to handle different service Internet application type e g Email FTP Web server etc from the Internet Computers use numbers called port numbers to recognize a particular service Internet application type The Virtual Server allows you to re direct a particular service port number from the Internet WAN Port to a particular LAN private IP address and its service port number 300N3C READY ROUTER icap Choose your language Virtual Server You can configure the router as a Virtual Server allowing remote users to access services such as Web or FTP at your local PC Depending on the requested service TCP UDP port number the router will redirect the external service request to the appropriate internal server located at one of your local PCs Enable Virtual Server Bot Both Add Reset Current Virtual Server Table Apply Cancel J Enable Virtual Server Enable Virtual Server Private IP This is the LAN client host IP address that the Public Port number packet will be sent to Private Port This is the port number of the above Private IP host that the below Public Port number will be changed to when the packet enters your LAN to the LAN Server Client IP T
48. tup a WEP key in the Encryption page After this has been done make sure the wireless clients that you want to connect to the device are also setup with the same encryption key Fragment Threshold Fragment Threshold specifies the maximum size of a packet during the fragmentation of data to be transmitted If you set this value too low it will result in bad performance RTS Threshold When the packet size is smaller then the RTS threshold the wireless router will not use the RTS CTS mechanism to send this packet Beacon Interval is the interval of time that this wireless router broadcasts a beacon A Beacon is used to synchronize the wireless network Data Rate The Data Rate is the rate that this access point uses to transmit data packets The access point will use the highest possible selected transmission rate to transmit the data packets N Data Rate The Data Rate is the rate that this access point uses to transmit data packets for N compliant wireless nodes Highest to lowest data rate can be fixed Channel Bandwidth is the range of frequencies that will be used Preamble Type The Long Preamble can provide better wireless LAN compatibility while the Short Preamble can provide better wireless LAN performance Broadcast ESSID If you enabled Broadcast ESSID every wireless station located within the coverage of this access point can discover this access point easily If you are building a public wir
49. ve the above configurations Denial of Service DoS The Broadband router s firewall can block common hacker attacks including Denial of Service Ping of Death Port Scan and Sync Flood If Internet attacks occur the router can log the events 300N3C READY ROUTER uas The firewall can block common hacker attacks including DoS Discard Ping from WAN and Port Scan Denial of Service features z z z z Advanced Settings Avg Ping of Death Protections from Ping of Death attack Discard Ping From WAN The router s WAN port will not respond to any Ping requests Port Scan Protects the router from Port Scans Sync Flood Protects the router from Sync Flood attack Access You can restrict users from accessing certain Internet applications services e g Internet websites email FTP etc Access Control allows users to define the traffic type permitted in your LAN You can control which PC client can have access to these services 300N3C READY ROUTER imap Choose your language Access Control allows users to define the traffic type permitted or not permitted in your LAN You can control which PC uses what services or has access to If both MAC filtering and IP filtering are enabled the MAC filtering table will be checked first Enable MAC filtering Deny Oallow Ce OOOO MAC Filtering table l Reset Enable IP Fi
50. ype Select the port number protocol type TCP UDP or both If you are unsure then leave it to the default both setting Public Port Enter the service service Internet application port number from the Internet that will be re directed to the above Private IP address host in your LAN Comment The description of this setting Add Virtual Server Fill in the Private IP Private Port Type Public Port and Comment of the setting to be added and then click Add Then this Virtual Server setting will be added into the Current Virtual Server Table below Remove Virtual Server If you want to remove Virtual Server settings from the Current Virtual Server Table select the Virtual Server settings you want to remove in the table and then click Delete Selected If you want to remove all Virtual Server settings from the table just click the Delete All button Click Reset will clear your current selections Click Apply at the bottom of the screen to save the above configurations Special Applications Some applications require multiple connections such as Internet games video Conferencing Internet telephony and others In this section you can configure the router to support multiple connections for these types of applications Enable Trigger Port Enable the Special Application function Trigger Port This is the out going Outbound range of port numbers for this particular application Trigger Type Select whether
Download Pdf Manuals
Related Search