Raw International PF1 flat panel wall mount
Contents
1. equal distance to 2mm hole a b security vel j screw 14 A fixings holes on back of screen po It is important that the front plates are fixed as centrally as possible to screen To help achieve this there is a 2mm hole in the centre of each of the front plates Line this hole up so it is equal distance between the top and bottom fixings on the back of the screen fig 2 Once it is lined up the nearest fixing hole on the front plates to the top fixing on the plasma screen are the ones that should be fixed first fig 3 using appropriate screws washers isolators spacers Then fix the bottom two fixings through the slots using appropriate screws washers isolators spacers Please use an Allen key to tighten all four fixings Only use isolators if back of screen is not flush with the front plates screen Ensure front plates are situated in a centralised horizontal position tighten the screws on the top of the front plates fig 5 overleaf using a screw driver 3 Engaging Plasma with the wall Lift the display minimum 2 people with front plates attached so that the bars engage with the angled slots on the wall mounting plate fig 5 overleaf the screen is now safely suspended steel fixings 55 steel washer front plates nylon isolator2. 4 Security Oo Once the screen is safely suspended please tighten the bolts on the bottom right and left corner of the raw bracket using a screwdriver DO NOT OVER TIGHTEN This engages the front plates to the wall mounting plate to ensigelfe solsen cannot be crim the wall fig GOAN V O NNN ga RIN rrr it re rN rr Pdh Ten ND p F1 CONSULT AUTHORISED SERVICE PERSONNEL FOR THE INSTALLATION OF THIS UNIT INSTRUCTIONS l N STR U CTI O N MUST BE FOLLOWED PRECISELY FOR SAFE AND STABLE INSTALLATION RAW INTERNATIONAL ARE M AN U AL NOT LIABLE FOR ANY DAMAGE OR INJURY CAUSED BY MISHANDLING OR IMPROPER INSTALLATION List of components Spacers screen brack f M4x20mm x 4 M5x20mm x 4 M6x20m x 4 M8x20mm x 4 17x8 3x5 x 4 M4X600mm x 4 M5x55mm x 4 M6x55 x 4 M8x55mm x 4 17x8 3x10 x 4 3mm hex key x 1 M5x75mm 4 5mm hex key x 1 M8x75mm x 4 17x8 3x20 x 4 4mm hex key x 1 6mm hex key x 1 17x8 3x30 x 4 17x8 3x40 x 4 Screw driver 9 e LL o oro o Fl JC Screw driver INSTALLATION PLEASE READ CAREFULLY INSTALLATION OF THIS UNIT SHOULD ONLY BE CARRIED OUT BY QUALIFIED TECHNICIANS INSTALL IN AN APPROPRIATE LOCATION ONLY AFTER CHECKING WALL STRUCTURE AND DURABILITY FOR ACCIDENT PREVENTION CONSULT A QUALIFIED BUILDER IF IN ANY DOUBT AS
3. TO STRUCTURAL INTEGRITY OF WALL 1 Mounting wall plate Remove security screw from bottom of bracket and detach front plate fig 2 Mount wall plate fig 1 on wall in desired position using screws bolts suitable to construction of the wall If in any doubt please consult a qualified builder Attach screws bolts through as many holes slots as possible There are a total of 22 fixing holes on the back plate however the minimum amount of fixings that Raw International recommend is six If in any doubt as to strength of fixings please consult a qualified builder 2 Attaching front plates to the plasma screen Place the screen face down on soft cloth to prevent damage on a flat surface The fixings you use is dependent on the make and model of your screen There are different sets of fixings supplied with the bracket Only ONE set of fixings will be required In order to ascertain which set of fixings will be required screw fixings in the back of the screen before attempting to attach front plates Only ONE set of fixings will be of the correct diameter for your screen Mounting holes slots o o C 9 o o CR x75 o o o o o o o o o o o o o o C 3 o C o x o o B o o o o o o 9 doh f p o o Ws e r o o 2mm t hole
Download Pdf Manuals
Related Search