Raw International FT1 flat panel wall mount
Contents
1. Lift the screen minimum two people with front plates attached so that the bars engage with the angled slots on the wall mounting plates fig 5 overleaf The screen is now safely suspended i steel fixings i i lt gt steel washer front plates screen2. 4 Security Oo Once the screen is safely suspended please tighten the bolts on the bottom left and right of the bracket raw using a screw driver DO NOT OVER TIGHTEN This engages the front plates to the wall mounting plates o ensure heskin Sannot be ited Wall ig 6 ANN O AAO IN rrr gg eg Oh tre BR FT1 CONSULT AUTHORISED SERVICE PERSONNEL FOR THE INSTALLATION OF THIS UNIT INSTRUCTIONS l N STR U CTI O N MUST BE FOLLOWED PRECISELY FOR SAFE AND STABLE INSTALLATION RAW INTERNATIONAL ARE M AN U AL NOT LIABLE FOR ANY DAMAGE OR INJURY CAUSED BY MISHANDLING OR IMPROPER INSTALLATION List of components Spacers Penny Washer screen brack l M4x20mm x 4 M5x20mm x 4 M6x20m x 4 15x7 3x5 x 4 16x5 3x1 0 x 4 law M4X45mmx4 M5x45mm x4 5mm hex key x 1 15x7 3x10 x 4 M4x55mm x4 M5x55mm 4 M8x20mm x 4 15x7 3x30 x 4 Standard Washer 38mm hex key x 1 4mm hex key x 1 6mm hex key x 1 15x7 38x40 x 4 16x8 3x1 0 x 4 screw driver allen key screw driver 5 Adjusting the tilt mechanism Now that the screen is safely suspended on the wall using an allen key loosen the fixing on the tilt mechanism fig 7 Once you have chosen your desired tilt angle tighten the fixing on the tilt mechanism once again INSTALLATION PLEASE READ CAREFULLY INSTALLATION OF THIS UNIT SHOULD ONLY
3. BE CARRIED OUT BY QUALIFIED TECHNICIANS INSTALL IN AN APPROPRIATE LOCATION ONLY AFTER CHECKING WALL STRUCTURE AND DURABILITY FOR ACCIDENT PREVENTION CONSULT A QUALIFIED BUILDER IF IN ANY DOUBT AS TO STRUCTURAL INTEGRITY OF WALL 1 Mounting wall plate Remove security screw from bottom of bracket and detach front plate fig 2b Mount wall plate fig 1 on wall in desired position using screws bolts suitable to construction of the wall If in any doubt please consult a qualified builder Attach screws bolts through as many fixing as possible There are a total of 22 fixing holes on the back plate however the minimum amount of fixings that Raw International recommend is six If in any doubt as to strength of fixings please consult a qualified builder 2 Attaching front plates to the screen Firstly loosen the fixing which controls the tilt mechanism on the front plate fig 2a This will allow clear access to the front plate fixing holes which will be used to attach the from plate to the screen Place the screen face down on soft cloth to prevent damage on a flat surface fig 2b The fixings you use are dependent on the make and model of your screen There are different sets of fixings supplied with the bracket Only ONE set of fixings will be required In order to ascertain which set of fixings will be required screw fixings in the back of the screen before attempting to attach front plates Only ONE se
4. t of fixings will be of the correct diameter for your screen Mounting holes slots OG sem o 4 Oeo 0 o o o o o JT o Q 9 o o allen key a o fe fe fe o o Y Q a p f p e o o r o fe 2mm i t hole equal distance to 2mm hole j 9 P security igi j screw 74 A fixings holes on back of screen D po LE ze It is important that the front plates are fixed as centrally as possible to the screen To help achieve this there is a 2mm hole off centre of each of the front plates Line this hole up so it is equal distance between the top and bottom fixings on the screen fig 2b Once it is lined up the nearest fixing hole on the front plates to the top fixing on the screen are the ones that should be fixed first fig 3 using appropriate screws washers isolators spacers Please use an allen key to tighten all four screws Only use isolators if back of screen is not flush with the front plates Ensure front plates are situated in a centralised position tighten the screws on the bottom of the front plates fig 4 overleaf using a screw driver Now fully tighten the fi xing on the tilt mechanism 3 Engaging the screen with the wall
Download Pdf Manuals
Related Search