Lenco CR-333
Contents
1. Press the RADIO ON OFF button to turn the radio On The radio dial pointer will light 4 Select your desired station with the TUNING control 5 Adjust the VOLUME control to the desired setting 6 When you are finished listening press the RADIO ON OFF button to turn the radio Off The radio dial pointer light goes off Antenna Information AM The AM bar antenna is inside the cabinet If AM reception is weak change the position of cabinet until the internal antenna picks up the strongest signal SmartSat masxar FM The FM antenna is built in to the AC power cord If FM reception is weak try varying the position and direction of the power cord until you find the strongest signal Wake To RADIO 1 Turn the radio On and select the Band Station and Volume level that you wish to hear when the alarm comes on then turn the radio Off again 2 Reconfirm the wake up time and alarm mode settings for the alarm you are using Alarm 1 Alarm 2 or both Alarms 3 Set the ALARM selector switch for one or both alarms to the RADIO position The appropriate ALARM 1 and or ALARM 2 display will change from OFF to the selected wake up time 4 At the selected wake up time the radio will turn On It will play for one hour and then shut off automatically 5 To stop the radio sooner press either the appropriate ALARM 1 or ALARM 2 button or press the RADIO ON OFF button The rad2. The two small displays will revert to the Alarm 1 Alarm 2 indications a few seconds after you release the CALENDAR button Daylight Saving and Leap Year Adjustments All Daylight Saving and Leap Year adjustments are made automatically by the SmartSete internal computer as follows e Start of Daylight Saving Time At 1 59 59 AM on the last Sunday of daylight saving time the clock will automatically advance to 3 00 AM End of Daylight Saving Time At 2 59 59 AM on the last Sunday of daylight saving time the clock will automatically reset to 2 00 AM e Leap Year At 12 00 Midnight on February 28th the calendar display will change to 29 2 Manual Time Adjustments Some people like to set their clocks 5 to 10 minutes fast to make sure that they will always be on time Even though the SmartSete sets the time by itself you still have the option of adjusting the time manually if you wish To manually adjust the time display depress and hold the TIME button and press either the SET Up or Down buttons to adjust the time display ahead or back as desired Each press of the SET Up or Down buttons will change the display by one minute If you hold the SET Up or Down buttons the display will continue to change The display will change slowly at first one minute at a time But if you continue holding the SET Up or Down buttons the display will change rapidly NOTE If you manually adjust the time your new setti
3. IMPORTANT Leave the radio power cord connected to your AC outlet This will provide power to the SmartSetecomputer memory while the original lithium battery is removed 3 Turn the radio face up and use a small screwdriver to remove the screw securing the battery holder to the cabinet BE CAREFUL NOT TOLOSE THIS SMALL SCREW b gS 4 Remove the original battery from the holder and insert the new battery into the holder the same way observing the positive direction Slide the holder with the new battery back into the slot in the cabinet 5 Replace the screw that secures the battery holder in the cabinet 6 Turn the radio right side up and confirm that the LOW BATT indicator is Off 7 Save these instructions You ll have to do this again five to eight years from now Resetting The Clock After A Total Memory Loss If you do not change the built in lithium battery within a reasonable period of time after you see the warning indicator the lithium battery may become exhausted and will no longer be able to supply back up power to the SmartSete internal computer If the unit is disconnected from the AC outlet after the battery is exhausted or if a power interruption occurs the SmartSete memory will be lost and the clock will need to be reset when the power is restored Be sure to install a fresh lithium battery before you reset the clock otherwise the clock will need to be reset each time the power is interrupt
4. CR 333 OWNER S MANUAL Dual Alarm AM FM Clock Radio with Triple Display Touchless Snooze and Display Control and SmartSet o Automatic Time Setting System TO PREVENT FIRE OR SHOCK HAZARD DO NOT USE THIS PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions Keep these instructions Follow all instructions Heed all warnings 2 Do not use this apparatus near water 3 Clean only with dry cloth 4 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 5 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 6 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 7 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 8 Only use attachments accessories specified by the
5. Weekends only the alarm will only turn on Saturday and Sunday To check the Alarm Mode setting for Alarm 1 depress the ALARM 1 setting button The ALARM 1 display will show the Alarm 1 wake up time and the day of the week indicators will show you the alarm mode which is selected e If all 7 indicators are On the Everyday mode is selected e If only the Monday through Friday indicators are On the Weekdays only mode is selected e If only the Saturday and Sunday indicators are On the Weekends only mode is selected To change the Alarm Mode setting for Alarm 1 hold the ALARM 1 setting button and press the ALARM MODE bution until the day indicators show the desired mode setting Weekdays only Weekends only or Everyday operation Release the ALARM MODE and ALARM 1 setting buttons and the display will return to the correct Day Follow the same procedure to select the desired Alarm Mode for Alarm 2 if necessary Checking The Wake Up Times And Alarm Mode Whenever you want to check the wake up time or the alarm mode settings simply press either the ALARM 1 or ALARM 2 setting buttons The respective Alarm display will show the wake up time and the day indicators will show you the alarm mode which is currently selected Release the ALARM 1 or ALARM 2 setting buttons to return to correct Day Listening To The Radio 1 Set the BAND selector to the desired band AM or FM 2 Set the VOLUME control to a low setting 3
6. arm 1 or Alarm 2 switches to their OFF positions or use the SNOOZE control the display will return to the Off position after 10 seconds Changing The Lithium Battery Like all batteries eventually the built in lithium battery will need to be replaced A number of factors such as the length of time between the date the radio was manufactured and the date you plugged it in for the first time determine the amount of time before replacement During this initial storage period the lithium battery is supplying power to the SmartSetecomputer memory Once you plug the radio in your household outlet supplies the power and the battery is not being used A fresh lithium battery can supply power to the SmartSete computer for at least 3 years even if it is never connected to an AC power supply If your radio was connected to your AC supply within a few months after it was manufactured and you experience only the normal nuisance type short duration power interruptions your battery may last for up to 5 years or even longer When the battery power drops below a certain level the LOW BATT indicator will Flash When you see this indicator you should change the battery as soon as it is convenient for you to do so To change the battery proceed as follows 1 Purchase a replacement 3V lithium battery wherever batteries are sold The battery type is CR2430 or equivalent 2 Remove the battery from its package so it is ready to install
7. ber on the bottom of your radio and write this number in the space provided on the Warranty page of this manual e Place your radio on a level surface such as a table desk or shelf convenient to an AC outlet out of direct sunlight and away from sources of excess heat dirt dust moisture humidity or vibration e Unwind the AC power cord and extend it to its full length The FM antenna is built in to this cord It must be fully extended to provide the best FM reception Protect Your Furniture This model is equipped with non skid rubber feet to prevent the product from moving when you operate the controls These feet are made from non migrating rubber material specially formulated to avoid leaving any marks or stains on your furniture However certain types of oil based furniture polishes wood preservatives or cleaning sprays may cause the rubber feet to soften and leave marks or a rubber residue on the furniture To prevent any damage to your furniture we strongly recommend that you purchase small self adhesive felt pads available at hardware stores and home improvement centers everywhere and apply these pads to the bottom of the rubber feet before you place the product on fine wooden furniture Power Source This radio is designed to operate on normal 230V 50Hz AC power only Do not attempt to operate the radio on any other power source You could cause damage to the radio that is not covered by your warranty This radi
8. buzzer and turn on the radio immediately press the RADIO ON OFF button instead of the ALARM 1 or ALARM 2 button 5 If you do not want the alarm to turn the buzzer on the following day set the appropriate ALARM selector to the OFF position The respective alarm display will show OFF Radio And Buzzer Operation You may also set one alarm for wake to radio and the other for wake to buzzer Just set the ALARM 1 and ALARM 2 selector switches to the desired positions Snooze Repeat Alarm After the alarm turns On in the morning you can press the SNOOZE SLEEP OFF button on the top cabinet for a few extra minutes sleep The snooze LED indicator flashes DAY OF WEEK LOW BATT The alarm will stop for approximately 9 minutes and then comes On again Touchless Snooze Control You can also activate the Snooze alarm without physically touching the SNOOZE SLEEP OFF button When the alarm sounds in the morning just wave your hand in front of the WAVE SENSOR on the front panel see illustration to activate the Snooze alarm The Touchless Snooze Control works by detecting body heat For best results your hand should be within 40 cm of the front right panel SLEEP To Music Timer You can program the sleep timer to play the radio for up to 99 minutes and then shut off automatically 1 Press the SLEEP button The display will briefly show L 30 and the radio will begin to play After 30 min
9. d then switches off again Brilliant Just like every other SmartSete model this clock radio has a built in long life lithium battery that can provide back up for all of the important settings for up to 5 years or even longer No need to try and remember to install a fresh 9V battery ever 6 months And when it s time to change the lithium battery the low battery indicator will flash in the display e Operate controls and switches as described in the manual e Before turning on the power make certain that the power cord is properly installed e When moving the set be sure to first disconnect the AC power cord e Avoid installing this unit in places exposed to direct sunlight or close to heat radiating appliances such as electric heaters on top of other stereo equipment that radiates too much heat places lacking ventilation or dusty areas places subject to constant vibration and or humid or moist areas Unpacking And Set Up e Remove the radio from the carton and remove all packing material from the radio We suggest that you save the packing material if possible in the unlikely event that your radio ever needs to be returned for service The original carton and packing material is the only safe way to pack your radio to protect it from damage in transit e Remove any descriptive labels or stickers on the front or top of the cabinet Do not remove any labels or stickers from the back or bottom of the cabinet e Note the serial num
10. ed If the lithium battery is exhausted and you experience an interruption in the AC power supply the clock will reset itself to its initial default setting when the power is restored The initial default setting is 12 00 AM SATurday January 1st 1 01 2005 wa wh AM ALARM a iL CU U3 If you notice that the time on your SmartSete clock radio is completely incorrect and the DAY OF WEEK indicator is also wrong press the CALENDAR bution If the small displays are showing 01 1 and 2005 you probably experienced a total memory loss To reset the clock after a total memory loss proceed as follows 1 Follow the instructions on page 19 and install a new CR2430 lithium battery in the battery compartment 2 Connect the radio to your AC outlet and let the clock set itself 3 Depress the CALENDAR button The ALARM displays will change to Month Date and Year e While holding the CALENDAR and TIME buttons press the SET Up button to set the ALARM 2 display to the correct year then release the buttons e While holding the CALENDAR button press the SET Up button to set the ALARM 1 display to the correct Month and Date When the correct month and date appear on the display release the buttons e The DAY OF WEEK indicator will change automatically as you adjust the Year Month Date settings 4 Depress the TIME button and the SET Up buttons to set the display to the correct ti
11. etting after a power interruption Actually there are twenty four time zones you can select Your default time zone number is 23 Time zone setting according to the Greenwich timetable GMT Greenwich zero time 1 GMT 1 2 GMT 2 3 GMT 3 4 GMT 4 5 GMT 5 6 GMT 6 7 GMT 7 8 GMT 8 9 GMT 9__ 10 GMT 10 11 GMT 11 12 GMT 12 13 GMT 11 14 GMT 10 15 GMT 9 16 GMT 8 17 GMT 7 18 GMT 6 19 GMT 5 20 GMT 4 21 GMT 3 22 GMT 2 23 GMT 1 To change the default time zone display depress the TIME ZONE button The number 23 will appear on the display indicating that the default zone is ZONE 23 Hold the TIME ZONE button and then press either the SET Up or Down button until your own time zone appears on the display then release the buttons The clock display will change to the correct time in the time zone you selected The clock will always return to the correct time in the zone you selected after every power interruption If you move to a different time zone simply change the default zone display to the new zone and the SmartSete will remember that setting for you Month Date Year Display To see the correct date at any time press the CALENDAR bution The correct month and date will appear in the ALARM 1 display and the correct year will appear in the ALARM 2 display The month and date is displayed in the DD MM format For example May 21s will be displayed as 21 5
12. io will stop but the alarm remains set and will turn the radio on again at the same time on the following day depending on the Alarm Mode setting 6 If you do not want the alarm to turn the radio on the following day set the appropriate ALARM selector to the OFF position The respective alarm display will show OFF ALARM 1 RADIO 3 BUZZER orr ALARM 2 RADIO 3 is BUZZER ore a DIMMER HIGH 3 LOW e OFF WAVE f Wake To BUZZER Crescendo Alarm NOTE Alarm 1 and Alarm 2 have different buzzer sounds e Alarm 1 is a Single beep sound e Alarm 2 is a Double beep sound You will be able to tell which alarm is going off by the sound that it makes 1 Reconfirm the wake up time and alarm mode settings for the alarm you are using Alarm 1 Alarm 2 or both alarms 2 Set the ALARM selector switch for one or both alarms to the BUZZER position The appropriate ALARM 1 and or ALARM 2 display will change from OFF to the selected wake up time 3 At the selected wake up time the buzzer will sound It will begin softly and gradually increase in volume to wake you up It will continue for one hour and then shut off automatically 4 To stop the buzzer sooner press either the appropriate ALARM 1 or ALARM 2 button The buzzer will stop but the alarm remains set and will turn the buzzer on again at the same time on the following day depending on the Alarm Mode setting To stop the
13. manufacturer 9 Unplug this apparatus during lightning storms or when unused for long periods of time 10 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 11 This appliance shall not be exposed to dripping or splashing water and no object filled with liquids such as vases shall be placed on the apparatus 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Do not overload wall outlet Use only power source as indicated 14 Use replacement parts as specified by the manufacturer 15 The product may be mounted to a wall only if recommended by the manufacturer 16 Upon completion of any service or repairs to this product ask the service technician to perform safety checks Thank you for purchasing this SmartSete Dual Alarm Clock Radio with Triple Display plus Touchless Snooze and Display Control Features We think you will be truly amazed by all of the features that we have packed into this compact bedside companion First of all there is Emerson s patented SmartSete A
14. me 5 After you set the time reconfirm that the Day and Month Date displays are still correct Make final adjustments if necessary The SmartSete clock memory is now reset and the new lithium battery will maintain it for the next 5 to 8 years depending on the number and duration of the power outages you experience IMPORTANT NOTE After resetting the clock don t forget to reset your wake up times and alarm mode settings and sleep timer settings as well Lithium Battery Precautions e Dispose of the old battery properly Do not leave it lying around where a young child or pet could play with or swallow it If the battery is swallowed contact a physician immediately e Battery may expolde or leak if mistreated Do not attempt to recharge it or disassemble it Do not dispose of the old battery in a fire If the cabinet becomes dusty wipe it with a soft cloth If the cabinet becomes smudged or dirty clean it with a soft slightly dampened cloth Never allow water or any liquid to get inside the cabinet Never use any abrasive cleaners or cleaning pads as these will damage the finish of your radio
15. ng is entered into the SmartSete memory If the power is interrupted the display will return to your new setting not the original setting when the power is restored Adjusting The Wake Up Times Your SmartSete clock radio has two separate alarms that can be set and used independently You may use the alarms to wake two people at different times or you may use one alarm for weekdays and the other for weekend wake up times The procedure for adjusting the wake up time is the same for both Alarm 1 and Alarm 2 1 Depress and hold either the ALARM 1 or ALARM 2 setting button The respective Alarm 1 or Alarm 2 time and DAY OF WEEK indicators will appear EK MON TUE WED THU FRI SAT SUN 30A rm HE AM ALARM DUAL Lt ie LARM LI 2 While holding the ALARM 1 or ALARM 2 setting button depress either the SET Up or Down button to move the alarm display ahead or back to your respective Alarm 1 or Alarm 2 desired wake up time 3 When the desired wake up time appears on the display release the SET Up or Down buttons 4 When the desired wake up time appears on the display release the ALARM 1 or ALARM 2 setting buttons Selecting The Alarm Mode Your SmartSete clock radio allows you to select from among three different alarm operation modes for either alarm The alarm modes are e Everyday the alarm will turn on all 7 days e Weekdays only the alarm will only turn on Monday through Friday e
16. o should be connected to an AC outlet that is always live Do not connect it to an outlet that is controlled by a wall switch When the power to the radio is interrupted the built in lithium battery takes over to maintain the time and alarm settings To maximize the life of the lithium battery keep the radio connected to a live AC outlet at all times AC Plug AC Outlet AC Outlet AC Plug LOCATION OF CONTROLS AND INDICATORS 1 ALARM 1 Time Month Date Display 2 DIMMER HIGH LOW OFF WAVE Selector Switch 3 ALARM 2 RADIO BUZZER OFF Selector Switch 4 ALARM 1 RADIO BUZZER OFF Selector Switch 5 Time Display 6 WAVE SENSOR 7 DAY OF WEEK MON TUE WED THU FRI SAT SUN Indicators 8 LOW BATT Indicator 9 1 1 1 1 Setting The Time The First Time IMPORTANT The first time you connect your new SmartSeteclock radio to the AC outlet the internal computer will automatically set the time correctly for the area you live which is the initial default setting The displays will scroll for a few seconds and then show the correct Year Month Date Day and Time in your area Your clock is set correctly and running If you want to move to other European countries you must change the default zone display to your own zone which follows the Greenwich time standard You only do this one time and the SmartSete will remember the new default zone setting and will always return to that s
17. o the High position at our factory e LOW when the dimmer switch is set to the LOW position the display brightness is reduced by approximately 50 e OFF WAVE when the dimmer switch is set to the OFF WAVE position the display goes Off completely This is designed for people who prefer to sleep in total darkness However if you want to see the clock display at any time slowly wave your hand in front of the WAVE SENSOR on the front panel The clock display will immediately return to full brightness for 10 seconds and then shut off again automatically The effective operating range of the Wave Sensor is approximately 40 60 cm from the front panel NOTES A The clock radio must be at room temperature for the WAVE SENSOR to function properly If the radio has been in a cold location the WAVE SENSOR may not operate immediately Place the radio in the room where it will be used connect it to the AC outlet and allow approximately 30 minutes to 60 minutes for the radio to come to room temperature before testing the WAVE SENSOR function B If the dimmer switch is set to the OFF WAVE position the display will be completely off However at the Alarm time the display will return to full brightness automatically It will remain at full brightness for one hour and then return to the Off position If you stop the alarm immediately by pressing the respective Alarm 1 or Alarm 2 buttons or set the Al
18. utes the radio will shut Off automatically DAY OF WEEK LOW BATT ITI WAVE SENSOR o LAL ALARM AM y wi mi E E AM ALARM DUAL ALARM t t meg Each time you press the SLEEP button the sleep timer will start at 30 minutes This is the sleep timer default setting 2 To increase or decrease the amount of time that the radio will play before shutting off hold the SLEEP button and press either the SET Up or Down button to change the display to the desired sleep time up to a maximum of 99 minutes or a minimum of 01 minute NOTE When you change the sleep timer from the 30 minute default setting to a different setting the new setting becomes the default setting Whenever you activate the sleep timer it will begin with your new default setting and count down to zero from that point 3 To cancel the sleep timer before it counts down to 00 and shut the radio Off immediately press the SNOOZE SLEEP OFF Bar IMPORTANT Remember that the station and volume settings you choose for the SLEEP To Music operation are the same settings you will hear if you set the alarm for wake to radio the following morning Display Brightness Control This SmartSete Clock Radio features a unique display brightness control system that gives you three convenient options e HIGH when the dimmer switch is set to the HIGH position the clock display is always at full brightness The dimmer switch was set t
19. utomatic Time Setting System The first time you connect this clock radio to your AC outlet it will immediately set itself to the correct year month date day and time in your time Zone If you live in a different time zone there is one simple Time Zone adjustment to make and you will never see the dreaded flashing 12 00 display again It will automatically reset itself every time you have a power interruption and not just the time but your wake up times as well Daylight Saving Time and Leap Year adjustments are also done automatically through the year 2099 In addition to the jumbo amber time display there are two smaller displays that show the Alarm 1 and Alarm 2 wake up times so you can see at a glance that the alarms are set correctly If one of the alarms is off the display clearly shows OFF No guesswork required Like to hit that snooze bar in the morning but don t like reaching for the top of the radio Problem solved Just wave your hand in front of the Touchless Snooze Wave Sensor and go back to sleep for another 9 minutes No touching required Love that big display that s so easy to see but prefer to sleep in total darkness We thought of that one as well Just set the display dimmer control to the OFF WAVE position and the display goes off completely But if you need to check the time in the middle of the night just wave your hand in front of the sensor The display returns to full brightness for 10 seconds an
Download Pdf Manuals
Related Search