TP-LINK TL-SG1016
Contents
1. Panel sketch 3 2 Rear Panel The rear panel of the TL SG1024 only features a power receptacle which is an AC power receptacle Connect the female of the power cord head here and the male head to the AC power outlet Ey amp Figure 3 2 TL SG1024 Switch Rear Panel sketch 3 3 LED Indicators The LED indicators include Power Link Act and 1000Mbps LED indicators which are used for monitoring and pre troubleshooting of the Switch The following section shows the LED indicators for the switch along with an explanation of each indicator Ne Figure 3 3 TL SG1024 Switch LEDs sketch gt Power LED This indicator will light solid red when the Switch powers up If the LED is not lit please check the power supply and connection Link Act LED This indicator will light solid green when the corresponding port is connected to another device and will flash green when data is being transmitted or received on the working connection gt 1000Mbps LED This indicator will light solid green when the corresponding port is connected to a 1000Mbps device Yv Appendix A Specifications General IEEE802 3 10Base T Standards IEEE802 3u 100Base TX IEEE802 3ab 1000Base T Protocol CSMA CD Ethernet 10Mbps Half Duplex 20Mbps Full Duplex Data Transfer Fast Ethernet 100Mbps Half Duplex Rate 200Mbps Full Duplex Gigabit Ethernet 2000Mbps Full Duple2. as general ports or Uplink ports and any port can be simply plugged into a server a hub a router or a switch using the straight cable or crossover cable Diagnostic LEDs which display link status and activity allowing you to quickly 1 detect and correct problems on the network 1 2 Features gt gt v gt gt gt gt Complies with IEEE802 3 IEEE802 3u IEEE802 3ab standards 16 24 10 100 1000Mbps Auto Sense RJ45 ports supporting Auto MDI MDIX All ports Support Full Half Duplex transfer mode for 10 100Mbps and Full Duplex transfer mode for 1000Mbps Supports IEEE802 3x flow control for full duplex mode and backpressure for half duplex transfer mode Non blocking switching architecture that forwards and filters packets at full wire speed for maximum throughput Supports MAC address auto learning and auto aging LED indicators for monitoring power link speed and activity Rack mountable steel case Internal power supply Chapter 2 Installation 2 1 Mounting the Switch on a Desk Before place the Switch on a desk attach four rubber footpads to the flutes on the Switch bottom then lay the Switch on the desktop where can be have as much as 5kg placed on top Note 1 2 3 The electrical outlet shall be installed near the device and shall be easily accessible Make sure there is free space for radiating heat and air Make sure not to place anything too heavy on top of the switch 2 2 Mount
3. or operation of the TP LINK TL SG1016 TL SG1024 16 24 port Gigabit Ethernet Switch please contact us E mail support tp link com Website http www tp link com
4. TP LINK User Guide TL SG1016 TL SG1024 16 24 port Gigabit Ethernet Switch Rev 2 0 0 7106500823 COPYRIGHT amp TRADEMARKS Specifications are subject to change without notice TP LINK is a registered trademark of TP LINK TECHNOLOGIES CO LTD Other brands and product names are trademarks or registered trademarks of their respective holders No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from TP LINK TECHNOLOGIES CO LTD Copyright 2009 TP LINK TECHNOLOGIES CO LTD All rights reserved http www tp link com FCC STATEMENT FE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to pro vide reasonable protection against harmful interference in a_ residential installation This equipment generates uses and can radiate radio frequency energy and if not in stalled and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of
5. ing the Switch in a Rack The dimension of TL SG1016 TL SG1024 is designed according to the standard 19 rack mountable steel case of Electronic Industries Association Turn off all the equipment connected to the Switch before mounting it in the rack then rivet the two L brackets onto each side of the Switch fasten it with screws in the rack i ee EES Figure 2 1 Rivet the L brackets onto the Switch WILLA Figure 2 2 Fasten the Switch in the rack 3 2 3 Power On TL SG1016 TL SG1024 16 24 port Gigabit Ethernet Switch is powered by AC power supply Powering on the Switch it will automatically initialize and its LED indicators should respond as follows 1 All of the Link Act and 1000Mbps LED indicators will flash momentarily for one second which represent a resetting of the system 2 The Power indicator will light up If the LED indicators don t respond as described above please check the power supply and connection Chapter3 Identifying External Components This Chapter describes the front panel rear panel and LED indicators of the Switch TL SG1016 and TL SG1024 just differ in the number of LED indicators and ports and all figures in this guide are of TL SG1024 3 1 Front Panel The front panel of the TL SG1024 consists of switch LED indicators 24 10 100 1000Mbps RJ 45 ports TP UNK m roti b i ae a Figure 3 1 TL SG1024 Switch Front
6. place heavy objects on the switch Chapter 1 Introduction of the Product This chapter describes the features of the TL SG1016 TL SG1024 16 24 port Gigabit Ethernet Switch 1 1 Overview of the Product The TL SG1016 TL SG1024 16 24 port Gigabit Ethernet Switch provides you with a high performance low cost easy to use seamless and standard upgrade to boost your old network to 1000Mbps Increase the speed of your network server and backbone connections make Gigabit a reality Power users in the home office workgroup or creative production environment can now move large bandwidth intensive files faster Transfer graphics CGI CAD or multimedia files and other applications that have to move large files across the network almost instantly The TP LINK TL SG1016 TL SG1024 features a non blocking switching architecture that forwards and filters packets at full wire speed for maximum throughput MAC address auto learning and auto aging IEEE802 3x flow control for full duplex mode and backpressure for half duplex mode It is compatible with all 10 100 and 1000Mbps Ethernet devices because it is standard based It protects your existing network investments while providing you with a straightforward migration path to faster Gigabit speeds The TP LINK TL SG1016 TL SG1024 is plug and play and no configuration is required Auto MDI MDI X cable detection on all ports eliminate the need for crossover cable or Uplink port Each port can be used
7. the following measures gt Reorient or relocate the receiving antenna gt Increase the separation between the equipment and receiver gt Connect the equipment into an outlet on a circuit different from that to which the receiver is connected gt Consult the dealer or an experienced radio TV technician for help This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment CE Mark Warning CE This is a class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Package Contents The following contents should be found in your package gt One TL SG1016 TL SG1024 Switch gt One power cord gt This User Guide gt Rubber footpads for Desk mount gt Rack mount kit for installing the switch in a 19 inch rack Note Make sure that the package contains the above items If any of the listed items are damaged or missing please contact with your distributor Safety Notices Do not use this product near water Avoid using this product during an electrical storm Do not
8. x 10Base T UTP category 3 4 5 cable maximum 100m EIA TIA 568 100 STP maximum 100m 100Base TX UTP category 5 5e cable maximum 100m EIA TIA 568 100 STP maximum 100m 1000Base T UTP category 5 5e cable maximum 100m EIA TIA 568 100 STP maximum 100m Number of Ports 16 24 10 100 1000Mbps Auto Negotiation RJ 45 ports Network Media Cable LED indicators Power Link Act 1000Mbps Transfer Method Store and Forward MAC Address Automatically learning automatically Learning aging 10Base T 14881pps Port Frame Filter Rate 100Base Tx 148810pps Port 1000Base T 1488095pps Port 10Base T 14881pps Port Frame Forward Rate 100Base Tx 148810pps Port 1000Base T 1488095pps Port Environmental and Physical 44mm WXDXH Power Supply Output Operating Temperature Storage Temperature Operating Humidity 10 90 non condensing Storage Humidity 5 90 non condensing Appendix B Troubleshooting gt The Power LED is not lit Make sure the AC power cord connected the Switch with power source properly Make sure the power source is ON The Link Act LED is not lit when a device is connected to the corresponding port Make sure that the cable connectors are firmly plugged into the Switch and the device Make sure the connected device is turned on and working well The cable must be less than 100 meters long 328 feet Appendix C Contact Information For help with the installation
Download Pdf Manuals
Related Search