ID TECH Omni
Contents
1. SPECIFICA TIONS Power Requirements Bar Code Power Requirements Magnetic Operating Current Operating Temperature Weatherproof Option Storage Temperature Relative Humidity Magnetic Head Life Rail and Cover Life Magnetic Read Rate Bar Code Source Light Minimum Bar Code PCS Bar Code Centerline Bar Code Resolution Magnetic Stripe Formats Swipe Speed Card Width Power 5 VDC 10 35mA maximum Ground 0 VDC GND Power 5 VDC 10 50mV ripple maximum Ground 0 VDC GND Chassis Ground connected to GND and magnetic head case 30mA maximum for bar code only 5mA for magnetic stripe only 32 F to 131 F 0 C to 55 C 31 F to 140 F 35 C to 60 C without ice build up on magnetic head 31 F to 140 F 35 C to 60 C Maximum 95 non condensing 1 000 000 passes minimum 1 000 000 passes minimum Less than one error in 500 000 bits on cards conforming to ISO 7811 1 5 not induced by operator error Visible red 660 nm or Infrared 930 nm 60 49 inches 12 50mm from bottom of slot to center of reading window 006 inches 6 mil minimum ISO 7811 AAMVA and CA DMV Bar Code 5 to 65 inches per second bi directional Magnetic Stripe 3 to 60 inches per second bi directional Bar code media 005 to 050 inches Magnetic stripe media 01 to 050 inches SPECIFICA TIONS Power Requirements Bar Cod2. DATA signal s level is steady at the rising and falling edges and during the low level of the CLOCK pulse BARCODE DATA SIGNAL The Barcode Data Output is a single open collector output that is normally at high impedance and at a high voltage level based on the supply voltage to the external pull up resistor The output is low to indicate a White area and high to indicate a Black area The rising and falling edges represent the contrast edges between White and Black as the barcode is scanned ID TECH supplies barcode decoder ASIC and decoder electronics as separate product OPERA TION Make sure the Omni is properly cabled and is receiving sufficient power To read a card slide the card in either direction through the slot with the magnetic stripe facing the magnetic head or the bar code facing the bar code module as appropriate CLOCK The CLOCK output is narrow pulse normally low and goes high when data is valid The data level is stable at both the rising and falling edges of the CLOCK pulse CLOCK pulse width is typically 32 microseconds CARD PRESENT The CARD PRESENT signal indicates data is being read from the media being passed through the slot It will not switch until flux reversals magnetic pulses have been detected After the flux reversals have been detected CARD PRESENT goes low It stays low throughout the reading process and for 5 to 10 milliseconds after the last flux reversal is read Typically CARD PRESENT is us
3. NGE DATA 3 BLUE CLK 1 GREEN CLK 2 GRAY CLK 3 WHITE CARD PRESENT RED 5 VDC BLACK GROUND I O for bar code only reader with Tinned Wires COLOR PURPLE RED BLACK SIGNAL BAR CODE DATA 5 VDC GROUND I O for magnetic stripe amp bar code reader with Tinned Wires COLOR BROWN YELLOW ORANGE BLUE GREEN GRAY WHITE PURPLE DATA RED BLACK SIGNAL DATA 1 DATA 2 DATA 3 CLK 1 CLK 2 CLK 3 CARD PRESENT BAR CODE 5 VDC GROUND MAGSTRIPE DATA CLOCK amp CARD PRESENT SIGNALS The following is a timing diagram of typical DATA and CLOCK signals from ID TECH electronics CARD PRESENT CLOCK DATA BIT VALUE 5 at 0 I O for magnetic stripe only reader with Tinned Wires COLOR SIGNAL BROWN DATA 1 YELLOW DATA 2 ORANGE DATA 3 BLUE CLK 1 GREEN CLK 2 GRAY CLK 3 WHITE CARD PRESENT RED 5 VDC BLACK GROUND I O for bar code only reader with Tinned Wires COLOR PURPLE RED BLACK SIGNAL BAR CODE DATA 5 VDC GROUND I O for magnetic stripe amp bar code reader with Tinned Wires COLOR BROWN YELLOW ORANGE BLUE GREEN GRAY WHITE PURPLE DATA RED BLACK SIGNAL DATA 1 DATA 2 DATA 3 CLK 1 CLK 2 CLK 3 CARD PRESENT BAR CODE 5 VDC GROUND MAGSTRIPE DATA CLOCK amp CARD PRESENT SIGNALS The following is a timing diagram of typical DATA and CLOCK signals from ID TECH electronics CARD PRESENT CLOCK DATA BIT VALUE Hoy 0
4. OM N i Slot Reader TIL Users Manual D on ANCE n ASE Coast o ats en on MLL Be E A Tayr l T ID TECH 10721 Walker Street Cypress California 90630 714 761 6368 www idtechproducts com a IDT CH 80028503 005 Rev D RO5 07 Value through Innovation TM OMNI Slot Reader TIL Users Manual ID TECH 10721 Walker Street Cypress California 90630 714 761 6368 www idtechproducts com IDT CH Value through Innovation 80028503 005 Rev D R05 07 AGENCY APPROVED Specifications for subpart B of part 15 of FCC rule for a Class A computing device LIMITED WARRANTY ID TECH warrants this product to be in good working order for a period of one year from the date of purchase If this product is not in good working order as warranted above or should this product fail to be in good working order at any time during the warranty period repair or replacement shall be provided by ID TECH This warranty does not cover incidental or consequential damages incurred by consumer misuse or modification of said product For limited warranty service during the warranty period please contact ID TECH to obtain an RMA number and instructions for returning the product 2005 International Technologies amp Systems Corporation The information contained herein is provided to the user as a convenience While every effort has been made to ensure accuracy ID TECH is not responsible for damages that might occur because of err
5. The specifications described herein were cur rent at the time of publication but are subject to change at any time without prior notice ID TECH is a registered trademark of International Technologies amp Systems Corporation Omni and Value through Innovation are trademarks of Interna tional Technologies amp Systems Corporation CLOCK The CLOCK output is narrow pulse normally low and goes high when data is valid The data level is stable at both the rising and falling edges of the CLOCK pulse CLOCK pulse width is typically 32 microseconds CARD PRESENT The CARD PRESENT signal indicates data is being read from the media being passed through the slot It will not switch until flux reversals magnetic pulses have been detected After the flux reversals have been detected CARD PRESENT goes low It stays low throughout the reading process and for 5 to 10 milliseconds after the last flux reversal is read Typically CARD PRESENT is used to signal the start and finish of a card read It may also be used as an interrupt signal for alerting the firmware that the reading operation is in process This is an open drain output which usually has an external pull up resistor If required CARD PRESENT signals from more than one read circuit may be tied together to provide a single signal DATA The DATA output level indicates the value of the bit being decoded during a CLOCK pulse It is a low level for ones 1 and a high level for zeros 0 The
6. and magnetic versions are as follow MAGNETIC PIN ODO oOoNnNDc URUN e BAR CODE PIN O COND MN BWN COLOR BLUE BROWN GRAY YELLOW GREEN ORANGE BLACK WHITE SIGNAL CLK1 DATAI CLK3 DATA2 CLK2 DATA3 GND CARD PRESENT VCC SIGNAL VCC Host needs to provide 8 2K pull up resistor for TTL barcode only 4 10 for Track 2 or 24 for Tracks 1 and 3 have been detected and stays valid until after the last pulse is read Media may be read bi directionally without any pre conditioning of the electronics although the host system must employ enough data storage to ensure it can properly store and utalize the decoded bit sequence HOST CONNECTIONS The undecoded Omni reader is connected to a decoder box using a 9 pin squeeze to release connector Pinout designations for both bar code and magnetic versions are as follow MAGNETIC PIN OAOANINMN BWN e BAR CODE PIN O COND N BWN Ke COLOR BLUE BROWN GRAY YELLOW GREEN ORANGE BLACK WHITE SIGNAL CLK1 DATAI CLK3 DATA2 CLK2 DATA3 GND CARD PRESENT VCC SIGNAL VCC Host needs to provide 8 2K pull up resistor for TTL barcode only 4
7. e Power Requirements Magnetic Operating Current Operating Temperature Weatherproof Option Storage Temperature Relative Humidity Magnetic Head Life Rail and Cover Life Magnetic Read Rate Bar Code Source Light Minimum Bar Code PCS Bar Code Centerline Bar Code Resolution Magnetic Stripe Formats Swipe Speed Card Width Power 5 VDC 10 35mA maximum Ground 0 VDC GND Power 5 VDC 10 50mV ripple maximum Ground 0 VDC GND Chassis Ground connected to GND and magnetic head case 30mA maximum for bar code only 5mA for magnetic stripe only 32 F to 131 F 0 C to 55 C 31 F to 140 F 35 C to 60 C without ice build up on magnetic head 31 F to 140 F 35 C to 60 C Maximum 95 non condensing 1 000 000 passes minimum 1 000 000 passes minimum Less than one error in 500 000 bits on cards conforming to ISO 7811 1 5 not induced by operator error Visible red 660 nm or Infrared 930 nm 60 49 inches 12 50mm from bottom of slot to center of reading window 006 inches 6 mil minimum ISO 7811 AAMVA and CA DMV Bar Code 5 to 65 inches per second bi directional Magnetic Stripe 3 to 60 inches per second bi directional Bar code media 005 to 050 inches Magnetic stripe media 01 to 050 inches Slot Width 055 inches 1 37mm Dimensions Length 5 inches 127mm Width 2 05 inches 52mm Height 1 38 inche
8. ed to signal the start and finish of a card read It may also be used as an interrupt signal for alerting the firmware that the reading operation is in process This is an open drain output which usually has an external pull up resistor If required CARD PRESENT signals from more than one read circuit may be tied together to provide a single signal DATA The DATA output level indicates the value of the bit being decoded during a CLOCK pulse It is a low level for ones 1 and a high level for zeros 0 The DATA signal s level is steady at the rising and falling edges and during the low level of the CLOCK pulse BARCODE DATA SIGNAL The Barcode Data Output is a single open collector output that is normally at high impedance and at a high voltage level based on the supply voltage to the external pull up resistor The output is low to indicate a White area and high to indicate a Black area The rising and falling edges represent the contrast edges between White and Black as the barcode is scanned ID TECH supplies barcode decoder ASIC and decoder electronics as separate product OPERA TION Make sure the Omni is properly cabled and is receiving sufficient power To read a card slide the card in either direction through the slot with the magnetic stripe facing the magnetic head or the bar code facing the bar code module as appropriate I O for magnetic stripe only reader with Tinned Wires COLOR SIGNAL BROWN DATA 1 YELLOW DATA 2 ORA
9. er to insure reliable reading under varying conditions the Omni will read magnetic media at speeds from 5 inches per second IPS to 55 IPS with typical accelerations The output signals consist of a DATA and CLOCK for each encoded track The electronics operate with 5VDC 10 A CARD PRESENT signal is provided to alert the host when magnetic media is passed through the reader It is activated after magnetic pulses 3 Slot Width 055 inches 1 37mm Dimensions Length 5 inches 127mm Width 2 05 inches 52mm Height 1 38 inches 35mm Weight 1 Ib Cable Length 2 foot unterminated cable DESCRIPTION The rugged Omni slot reader can read bar codes or 1 2 or 3 tracks of magnetic stripe information in heavy use applications The Omni has a metal base and thick plastic housing The metal base allows for mounting with screws or Velcro fasteners The single I O cable provides the connections for electrical power and decoded data signals There are three options for the I O cable If the I O cable is terminated with a 9 pin connector the Omni will be either a magnetic stripe reader or a barcode reader not both If the I O cable is terminated with striped and tinned wires the Omni can be a magnetic stripe reader a barcode reader or able to read both technologies The electronics for magnetic stripe media are located on a single PCA mounted below the 99mm rail assembly TTL level signals data and clock go directly out throug
10. h an I O cable The electronics for bar code media are located on a single PCA mounted to the bar code module Again TTL level signals go directly out through an I O cable The Omni reliably processes data encoded within ANSI and ISO standards on both high and low coercivity magnetic media The circuit is designed to read cards demagnetized down to 30 or 40 of ISO and ANSI signal levels on tracks 1 3 or 2 respectively These reading characteristics are designed to insure that the Omni will reliably read real world cards In order to insure reliable reading under varying conditions the Omni will read magnetic media at speeds from 5 inches per second IPS to 55 IPS with typical accelerations The output signals consist of a DATA and CLOCK for each encoded track The electronics operate with SVDC 10 A CARD PRESENT signal is provided to alert the host when magnetic media is passed through the reader It is activated after magnetic pulses 3 10 for Track 2 or 24 for Tracks 1 and 3 have been detected and stays valid until after the last pulse is read Media may be read bi directionally without any pre conditioning of the electronics although the host system must employ enough data storage to ensure it can properly store and utalize the decoded bit sequence I O CABLE CONNECTIONS lt 9 PIN The undecoded Omni reader can be connected to a decoder box using a 9 pin squeeze to release connector Pinout designations for bar code
11. ors or omissions including any loss of profit or other commercial damage The specifications described herein were cur rent at the time of publication but are subject to change at any time without prior notice ID TECH is a registered trademark of International Technologies amp Systems Corporation Omni and Value through Innovation are trademarks of Interna tional Technologies amp Systems Corporation AGENCY APPROVED Specifications for subpart B of part 15 of FCC rule for a Class A computing device LIMITED WARRANTY ID TECH warrants this product to be in good working order for a period of one year from the date of purchase If this product is not in good working order as warranted above or should this product fail to be in good working order at any time during the warranty period repair or replacement shall be provided by ID TECH This warranty does not cover incidental or consequential damages incurred by consumer misuse or modification of said product For limited warranty service during the warranty period please contact ID TECH to obtain an RMA number and instructions for returning the product 2005 International Technologies amp Systems Corporation The information contained herein is provided to the user as a convenience While every effort has been made to ensure accuracy ID TECH 1s not responsible for damages that might occur because of errors or omissions including any loss of profit or other commercial damage
12. s 35mm Weight 1 Ib Cable Length 2 foot unterminated cable DESCRIPTION The rugged Omni slot reader can read bar codes or 1 2 or 3 tracks of magnetic stripe information in heavy use applications The Omni has a metal base and thick plastic housing The metal base allows for mounting with screws or Velcro fasteners The single I O cable provides the connections for electrical power and decoded data signals There are three options for the I O cable If the I O cable is terminated with a 9 pin connector the Omni will be either a magnetic stripe reader or a barcode reader not both If the I O cable is terminated with striped and tinned wires the Omni can be a magnetic stripe reader a barcode reader or able to read both technologies The electronics for magnetic stripe media are located on a single PCA mounted below the 99mm rail assembly TTL level signals data and clock go directly out through an I O cable The electronics for bar code media are located on a single PCA mounted to the bar code module Again TTL level signals go directly out through an I O cable The Omni reliably processes data encoded within ANSI and ISO standards on both high and low coercivity magnetic media The circuit is designed to read cards demagnetized down to 30 or 40 of ISO and ANSI signal levels on tracks 1 3 or 2 respectively These reading characteristics are designed to insure that the Omni will reliably read real world cards In ord
Download Pdf Manuals
Related Search