Philips Saeco HD8752
Contents
1. The height of the dispensing spout can be adjusted to better fit the dimensions of the cups that you wish to use Move the dispensing spout up or down with your fingers to adjust its height as shown in the image The recommended positions are For the use of small cups For the use of large cups Two cups can be placed under the dispensing spout to brew two cups of coffee at the same time STOP MEMO Green Green ENGLISH 21 Adjusting the coffee length The machine allows you to adjust the amount of brewed coffee according to your taste and or the size of your cups Each time the or button is pressed the machine brews a pre set amount of coffee Each button may be individually programmed for a specific brew setting The following procedure describes the programming of the button MEMO EF Place a cup under the dispensing spout Press and hold the button until the MEMO icon is displayed MEMO Then release the button The machine is now programming The machine starts brewing coffee When the STOP icon is displayed press the button as soon as the desired amount of coffee is reached Now the button is programmed each time it is pressed the machine will brew the same amount of espresso that was just programmed Note we To program the coffee button the same steps should be followed You should always using t2. then remove plug trom wall outlet 12 Do not use appliance for other than intended use 13 Save these instructions SAVE THESE INSTRUCTIONS CAUTION This appliance is for household use only Any servicing other than cleaning and user maintenance should be performed by an authorized service center Do not immerse machine in water To reduce the risk of tire or electric shock do not disassemble the machine There are no parts inside the machine serviceable by the user Repair should be done by authorized service personnel only l Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage Never use warm or hot water to fill the water tank Use cold water only Keep your hands and the cord away from hot parts of the appliance during operation Never clean with scrubbing powders or harsh cleaners Simply use a soft cloth dampened with water For optimal taste of your coffee use purified or bottled water Periodic descaling is still recommended every 2 3 months Do not use caramelized or flavored coffee beans INSTRUCTIONS FOR THE POWER SUPPLY CORD A short power supply cord or detachable power supply cord is to be provided to reduce risks resulting trom becoming entangled in or tripping over a longer cord Longer detachable power supply cords or extension cords are available and may used if care is exercised in their use If a long detachable power s
3. EJ Press the button to increase the value or the button to decrease the value E Press the button to confirm the setting j PHILIPS Green ENGLISH 15 Press the l button to exit the programming MENU INTENZA water filter installation We recommend you to install the INTENZA water filter as this prevents lime scale to build up in your machine and preserves a more intense aroma to your espresso coffee You can purchase separately the INTENZA water filter Please refer to the maintenance products page in this user manual for further details Water is a crucial part of every espresso so it s most important to always have it professionally filtered Using the INTENZA water filter will prevent mineral deposits from building up and improve your water quality EE Remove the small white filter from the water tank and store it in a dry place Remove the INTENZA water filter from its packaging immerse it ver tically with the opening positioned upwards in cold water and gently press the sides so as to let the air bubbles out Set the filter according to the measurements performed see previous chapter and indicated on the base of the filter A Soft water equals 1 or 2 on the test strip B Hard water standard equals 3 on the test strip C Very hard water equals 4 on the test strip 16 ENGLISH Put the filter into the empty water tank Press it
4. By doing this you help to preserve the environment The packing materials can be recycled Machine unplug the machine and cut the power cord Deliver the appliance and power cord to a service center or public waste disposal facility This product complies with EU directive 2002 96 EC The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product ENGLISH 53 TECHNICAL SPECIFICATION The manufacturer reserves the right to make changes to the technical specifications of the product Nominal Voltage Power Rating Power Supply service door Housing material Size wxhixa weigh Power Cord Length Coffee Bean Hopper Capacity Coffee grounds drawer capacity Safety mechanisms GUARANTEE AND SERVICE Guarantee For detailed information on your warranty and related conditions please read the warranty booklet by packed separately Service We wa
5. This function allows you to adjust the contrast of the display to better view the messages Water hardness This function allows you to adjust the water hardness setting according to the area where you live 1 very soft water 2 soft water 3 hard water 4 very hard water For more details please see the Measuring and programming water hardness chapter INTENZA water filter This function allows you to manage the INTENZA water filter For more details see the chapter related to filter handling Descaling cycle This function allows you to run the descaling cycle Factory settings This function allows you to reset all factory values ENGLISH 45 Programming mode example In this example it is shown how to program the display contrast Proceed in the same way to program the other functions The programming menu can only be accessed when the machine is on and shows this display Q Qs Green El Press the qm button to access programming FJ The first page is displayed Yellow Press the button to scroll the functions pages until the display Diseley contrast function is displayed contrast Yellow Press the and buttons to increase or decrease the value of the function 46 ENGLISH ESC Display Yellow contrast EJ When fhe display value is changed the OK message appears Press the button to confirm the cha
6. Coffee brew button 26 Hot water steam selection button 27 ON OFF button 28 Aroma Pre ground coffee button 29 MENU button 30 Descaling solution to be purchased separately CP ee SaaS Ys 8 ENGLISH PREPARING FOR USE Machine packaging The original packaging has been designed and constructed to protect the machine during transport We recommend keeping the packaging material for possible future transport Machine installation EJ Remove the drip tray with grill from the packaging Remove the machine from the packaging 150mm 6 inches e Choose a safe level surface where there will be no danger of over turning it or being injured e Choose a location that is sufficiently well lit clean and near an easily reachable socket e Allow for a minimum distance from the sides of the machine as shown in the illustration For best use it is recommended to Attach the drip tray with grill to the machine Make sure it is fully inser ted nll Note The drip tray collects the water that comes out of the dispensing spout during each rinse self cleaning cycle as well as coffee that might be spilled during beverage preparation Empty and clean the drip tray daily and each time the full drip tray indicator is raised VV Caution NEVER remove the drip tray when the machine has just been turned on Wait a couple of minutes since the machine will carry out a rinse self cleaning cycle E
7. container 1 5L under both the steam hot water wand and the dispensing spout 42 ENGLISH OK a DESCALER E Red Red Red Red Red Red EJ Press the button to start the descaling cycle MEMO EI The machine will start dispensing the descaling solution at intervals The bar on the display shows the cycle progress gt Note The descaling cycle may be paused by pressing the button To resume the cycle press the button again This allows you to empty the contai ner or to stay away from the machine for a brief period of time oP EE When this icon is displayed the water tank is empty Remove the water tank rinse it and fill it up to the MAX level with fresh water Place it back into the machine Empty the drip tray and place it back Empty the container and place it back under the steam hot water wand and dispensing spout HA When inserting the water tank into the machine this icon is displayed Press the button to start the rinsing cycle MEMO Ef When this icon is displayed the water tank is empty Repeat steps 12 15 Then continue to step 17 END Red Yellow z T ENGLISH 43 When the water tank is empty remove the water tank rinse it and fill it up to the MAX level with fresh water Place it back into the machine GF Empty the container and place it back under the dispensing spout E When the am
8. no INTENZA water filter installed insert the small white filter previously removed into the water tank 18 ENGLISH ADJUSTMENTS The machine allows for certain adjustments so that you can brew the best tasting coffee possible Saeco Adapting System Coffee is a natural product and its characteristics may change according to its origin blend and roast The machine is equipped with a self adjusting system that allows the use of all types of coffee beans available on the market not for caramelized beans The machine automatically adjusts itself after brewing several cups of coffee to optimize the extraction of the coffee to the compactness of the ground coffee Adjusting the ceramic coffee grinder Ceramic coffee grinders always guarantee accurate grinding for every coffee blend and prevent the beans from overheating This provides for full aroma preservation delivering the truly Italian taste in every cup FN warning The ceramic coffee grinder contains moving parts that may be dan gerous Therefore do not insert fingers and or other objects Only adjust the ceramic coffee grinder using the grinder adjustment key Turn off the machine by pressing the ON OFF button and remove the plug from the socket before carrying out any type of operation inside the coffee bean hopper You can adjust the ceramic grinders to set the coffee grinding to your personal taste FN warning The grinder adjustment knob inside
9. the coffee bean hopper must be turned only when the ceramic coffee grinder is working This adjustment can be carried out by pressing and turning the grin der adjustment knob inside the coffee bean hopper using the grinder adjustment key provided with the machine Green Green ENGLISH 19 EE Press and turn the grinder adjustment knob one notch at a time You will taste the difference after brewing 2 3 cups of espresso FJ The reference marks inside the coffee bean hopper indicate the grind setting There are 5 different grind settings to choose from 1 Coarse grind lighter taste for dark roasted coffee blends to 2 Fine grind bolder taste for light roasted coffee blends When you adjust the ceramic coffee grinder to a finer setting your coffee will taste stronger For a milder coffee taste adjust the ceramic coffee grinder to a coarser setting Adjusting the aroma coffee strength Choose your favorite coffee blend and adjust the amount of coffee to be grounded until they meet your personal taste You can also select the pre ground coffee function Note Selection must be made prior to selecting coffee Four choices are possible by pressing the ce button Each time het button is pressed the aroma changes by one degree according to the selected amount D Mild aroma D Medium aroma Strong aroma ih pre ground coffee 20 ENGLISH Adjusting the dispensing spout
10. until it cannot move further down E Fill the water tank with fresh water and reinsert it into the machine EJ Dispense the entire water tank by using the hot water function see chapter Hot water dispensing Fill the water tank again EJ Press the mam button and scroll the pages by pressing me LZ 7 button until the following page is displayed Yellow KJ Press the button to select ON and press the _ _ button to confirm Yellow ET To exit press the D button Q 2 Qs Green In this way the machine has been programmed to inform the user of the need to replace the INTENZA water filter Replacing the INTENZA water filter When the INTENZA water filter needs to be replaced with a new one the following icon is displayed EJ Replace the filter as described in the previous chapter Yellow ESC ON WATER FILTER OFF PRESET ESC WATER ON FILTER P CFF 4 d Yellow Green Yellow ENGLISH 17 FJ Press the mam button and scroll the pages by pressing ner iz id button until the following icon is displayed Select the RESET option Press the oe button to confirm To exit press the 1 button The machine is now programmed to manage a new filter Note If the filter is already installed and you want to remove but not replace it select the OFF option instead If there is
11. NGLISH 9 EJ Remove the water tank KJ Rinse the water tank under fresh water Fill the water tank with fresh water up to the MAX level and reinsert it into the machine Make sure it is fully inserted i Caution Never fill the water tank with warm hot sparkling water or any other liquid as this may cause damage to the water tank and the machine EJ Remove the coffee bean hopper lid and slowly pour the coffee beans into the coffee bean hopper Note Do not pour too many coffee beans into the coffee bean hopper as this will reduce the grinding performance of the machine i Caution Only coffee beans must be put into the coffee bean hopper Ground coffee instant coffee caramelized coffee or any other object may damage the machine KJ Put the lid on the coffee bean hopper E Insert the plug into the socket located on the back of the machine EE Insert the plug of the other end of the power cord into a wall socket with suitable power voltage 10 ENGLISH Switch the power button to I to turn on the machine The display shows the stand by icon EE To turn on the machine simply press the ly button The display indi cates that the circuit must be primed START USING THE MACHINE FOR THE FIRST TIME When using the machine for the first time the following activities need to happen 1 You need to prime the circuit 2 The machine will perform an automatic rinse self cleaning cycl
12. Register your product and get support at www philips com welcome INTELIA Type HD8 52 USER MANUAL PLEASE READ THIS USER MANUAL CAREFULLY BEFORE USING THE MACHINE PHILIPS CE Saeco IMPORTANT SAFEGUARDS When using electrical appliances basic satety precautions should always be followed including the following l 2 J 8 9 Read all instructions Do not touch hot surtaces Use handles or knobs To protect against tire electric shock and injury to persons do not immerse cord plugs or appliance in water or other liquid Close supervision is necessary when the appliance is used by or near children Unplug trom outlet when not in use and before cleaning Allow to cool betore putting on or taking off parts and before cleaning the appliance Do not operate any appliance with a damaged cord or plug or after the appliance maltunctions or has been damaged in any manner Return appliance to the nearest authorized service facility for examination repair or adjustment The use of accessory attachments not recommended by the appliance manufacturer may result in fire electric shock or injury to persons Do not use outdoors Do not let cord hang over edge of table or counter or touch hot surtaces 10 Do not place on or near a hot gas or electric burner or in a heated oven 11 Always attach plug to appliance first then plug cord into wall outlet To disconnect turn any control to oft
13. T PN warning Danger of scalding Dispensing may be preceded by sprays of milk and steam The hot water steam wand may reach high temperatures Never touch it with bare hands Use the appropriate handle only EJ Fill 1 3 of a container with cold milk fell Note Use cold 5 C 41 F milk with a protein content of at least 3 to ensure optimum results when preparing a cappuccino You can use whole milk or low fat milk depending on your personal taste Insert the suction tube in the milk container i Caution Make sure that the suction tube is clean on the outside for hygienic reasons Place a cup under the Cappuccinatore Press the 4 button The following icon is displayed Press the button to start pouring milk froth EJ The following icon may be displayed during the preheating time requi red by the machine STOP Green oD oD UO ENGLISH 25 EJ When this icon is displayed the machine pours frothed milk directly in the cup Press the button to stop pouring EJ Place the container back in the fridge for correct milk storage AL Caution After frothing the milk clean the Cappuccinatore and the suction tube by dispensing a small amount of hot water into a container For detai led cleaning instructions please see the Cleaning and Maintenance chapter Note After frothing milk it is possible to brew an espresso or dispense hot water straight aft
14. a aS EEAS asi SEa Eiana 6 General descrip UONiare niei e a a E nienernr nore ir errr teer 7 PREPARING FOR USE scccsssesssvesssaucsssssssonscsensisessesevesbennednsvavecsavssssensssstestensevestesess 8 POTENT UO CHAIN ceases sees occlu bocca ce cenlsanonen cave w ene caionartn essbadtoatnaeeitea eect aorta 8 Machine MINS AN A OU sc ea cad cpt decease EE 8 USING THE MACHINE FOR THE FIRST TIME sssssccsssssscssssseccesssseccesssecceseees 10 Cd Ne eee ee ee cee ee eee ee nem ere ee ee eer 10 Automatic rinse self cleaning cycle s ssscsssecsosscssscsssecsnsssnsccssecessecenscensecssnecanseenscesseecsnecenseenaseensecanses 11 WELE ETA Yl E E dea cecal ans tenensosvsd eens easectnatate eepeandieeete 12 Measuring and programming water hardness sscsssssscsscssscssecsscssscnsssnsesscsnscnscenscssscnsesscatscenscasezses 14 INTENZA water filter installation sssccsssusxisinssntnan xennstasnnnp asa esta se wneatndh sng csa bo otiibinavaurontdedpaniponboe 15 Replacing the INTENZA water filter sscssssssssssscssssssssssssssssssssssssssecssscsussssecsuecesscssscssecsnscsscesesesss 16 ADJUSTMENTS sisististsoosiritiricninmmnnaniiininnianimuniinicansnanin 18 Saeco Adapting System eessssssssssssssseereeoreeesssssssssuessnserreroosssssssssssunsereeereeeossssssssnassnseerereossrossssssssnseres 18 Adjusting the ceramic coffee grinder sssssssssssescesssssssssssescessssssssossseeenssnssssassnseesnsnsn
15. e 3 You need to initiate a manual rinse cycle Circuit primin During this process fresh water flows through the internal circuit of the machine and the machine warms up This takes a few minutes EF Place a container under the Cappuccinatore STOF amp A LP 9 z T Yellow Yellow Green ENGLISH 11 Press the button to start the cycle The machine starts the auto matic priming of the circuit by letting out a pre set quantity of water through the Cappuccinatore EJ The bar under the icon shows the operation progress When the pro cess is completed the machine stops dispensing automatically EJ Then the display shows the machine warm up icon Automatic rinse self cleaning cycle When warm up is completed the machine automatically performs a rinse self cleaning cycle of the internal circuit with fresh water This takes less than a minute EJ Place a container under the dispensing spout to catch the small amount of water which will be dispensed EJ The machine shows this display Wait for the cycle to finish automati cally Note l v You can stop dispensing by pressing the button MEMO When the above steps are completed the machine shows this display 12 ENGLISH Manual rinse cycle During this process you activate the coffee brewing cycle and fresh water flows through the steam hot water circuit This takes a few minutes EF Place a con
16. e on the left If you don t do this you will not be able to froth milk Clean it thoroughly with an abrasive damp cloth Reassemble all the Cappuccinatore components and place it back in the machine Insert the Cappuccinatore until it locks in place in the steam wand seat Fig A Eg Caution If the Cappuccinatore is fitted up to its limit stop beyond the hi ghlighted seat it might not operate correctly since no milk is sucked in this case stop brewing let the Cappuccinatore cool down and SLIGHTLY move it downwards Fig B to place it back in its proper seat Fig A Follow this procedure to restore the correct operation of the Cappuccina tore 36 ENGLISH Monthly lubrication of the brew grou Lubricate the brew group after approximately 500 cups of coffee or once a month You can purchase separately the Saeco grease to lubricate the brew group Please refer to the maintenance products page in this user manual for further details Eg Caution Before lubricating the brew group clean it under fresh water and dry it as described in the Weekly cleaning of the brew group chapter EJ Apply the grease evenly on both side guides Lubricate the shaft too ENGLISH 37 Insert the brew group in its seat until it locks into place see Weekly cleaning of the brew group chapter Insert the coffee residues drawer Close the service door Insert the coffee grounds drawer Monthly c
17. ed before reinserting the drawer Preheat the cups with hot water Clean the hole of the steam wand using a pin Make sure that the machine is off and cold before performing this operation Clean the Cappuccinatore Change coffee blend or adjust the grinder as explained in chapter Adjusting the ceramic coffee grinder Descale the machine Turn the machine on Close the ser vice door The brew group automati cally returns to the initial position Remove the coffee grounds drawer before removing the brew group It may be necessary to change the type of coffee or the coffee grinder settings Machine actions The machine grinds the coffee beans but no coffee comes out See note Coffee is too weak See note Coffee is brewed slowly See note Coffee leaks out of the dispensing spout ENGLISH 51 Causes Solutions There is no water Fill the water tank and prime the circuit chapter Using the machine for the first time The brew group is dirty Clean the brew group Weekly clea ning of the brew group chapter The circuit is not primed Prime the circuit chapter Using the machine for the first time This might occur when the ma Brew a few cups of coffee as de chine is automatically adjusting scribed in chapter Saeco Adapting the dose System The dispensing spout is dirty Clean the dispensing spout This might occur when the ma Brew a few cups of coffee as de chine
18. ekly cleaning of the brew groUp esssesssesseseseseseseseeeeeeeeeeeeeseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeereeeeeerereeeeeeeeeeeees 30 Monthly cleaning of the Cappuccinatore c sessssssssssssesssesssesssesssesssccsscssscsssccsscssssssscssscssscessessecsssessees 32 Monthly lubrication of the brew group xis vaiesissoessseiasendeoasisasteseedoaeiat xcaavavinaseiasesasveaoloesuaasncaurartaasboioenan 36 Monthly cleaning of the brew group with Coffee Oil RemOver ssssssscssscsssssssssseesseessecsssssssesstecseerses 37 Monthly cleaning of the coffee bean hoppet ssscssssssssssssssscssssssssssesssssssssssesssecsessssssssesssecsssssseesses 39 DESCAUIN E E E E 40 PROGRAMMING siscissacessnaissvarassdoncodesacausaenreassassatsovesdenciesncisiessueensestesivetssnecsoeas 44 Adju staple parameters ess cect cde vad sees dat cries Erre arara EAAS EE EET EREEREER 44 Programming mode example sssssssssssssssssssssssteeesesssesssssssssssessteressennssssssssssssstteessrseeenssssssssesssstreeeeenss 45 MEANING OF THE DISPLAY SYMBOLS ssesessssesssssocsssoocsssoccessoceessoccessocessoosessoo 47 TROUBLESHOOTING iscisessirciititinisinieiircainiinianiisnuianiads 50 ENERGY SAVING scsssscossicvassizecivrniisrectostonsarainiineatimnnnndmimnnnnine 52 SSN CUD A cette E tte gers E cena rete etcetera 52 BDU OVS pani eevee eter ee A E teva ended esta veneer sists dene iva 52 TECHNICAL SPECIFICATION visissseitiinraniamicnranimimncntirican
19. er HOT WATER DISPENSING FN warning Danger of scalding Dispensing may be preceded by small jets of hot water The hot water steam wand may reach high temperatures never touch it with bare hands Use the appropriate handle only Before dispensing hot water check that the machine is ready to use and the water tank is filled EB Remove the pin with the suction tube from the Cappuccinatore 26 ENGLISH STOP Yellow Green Place a container under the Cappuccinatore Press the button The following icon is displayed Press the button to start dispensing hot water EJ The following icon may be displayed during the preheating time requi red by the machine EJ Pour the desired amount of hot water To stop the hot water dispen sing press the button MEMO Place the pin with suction tube back into the Cappuccinatore ENGLISH 27 CLEANING AND MAINTENANCE Daily cleaning of the machine Eg Caution Timely cleaning and maintenance of your machine is very important as it prolongs the life of your machine Your machine gets exposed to moist coffee and limescale continuously In this chapter it is described in detail which activities you need to perform at which frequency Not doing this will ultimately make your machine stop working properly This repair is NOT covered by your warranty Note Usea soft dampened cloth to clean the machine Donotwash any of i
20. he button to stop brewing coffee when the desired amount of coffee is reached Even when you are programming the coffee button MEMO 22 ENGLISH ESPRESSO AND COFFEE BREWING Before brewing coffee make sure that there are no warnings shown on the display and that both water tank and coffee bean hopper are filled Espresso and coffee brewing using coffee beans Green Green EF Place 1 or 2 cups under the dispensing spout FJ To brew an espresso or a coffee press the amp button to select the desired aroma EJ Press the button for an espresso or the button for a coffee EJ To brew 1 cup of espresso or coffee press the desired button once This icon will be displayed EJ To brew 2 cups of espresso or coffee press the desired button twice consecutively This icon will be displayed mal Note In this operating mode the machine automatically grinds and doses the correct amount of coffee Brewing two espressos requires two grinding and brewing cycles automatically carried out by the machine EJ After the pre brewing cycle coffee begins to pour out of the dispen sing spout WA Coffee brewing stops automatically when the pre programmed level is reached however it is possible to stop earlier by pressing the button LP oD oD gt UO ENGLISH 23 Espresso and coffee brewing using pre ground coffee This function allows to
21. he coffee ground drawer and open the service door Remove the coffee residues drawer and then the brew group i Wash the brew group thoroughly with fresh water lL l C Green ENGLISH 39 EE After rinsing the brew group insert it again in its seat until it locks into place see Weekly cleaning of the brew group chapter Insert the coffee residues drawer and the coffee ground drawer Close the service door Press the o button to select the pre ground coffee function without adding ground coffee Press the button to start a coffee brewing cycle MEMO Repeat steps 12 13 twice Make sure you discard the dispensed water IB To clean the drip tray place Coffee Oil Remover tablet inside and fill it up to 2 3rds full with hot water Let the cleaning solution take effect for about 30 minutes then rinse thoroughly Monthly cleaning of the coffee bean hopper Clean the coffee bean hopper once a month when it is empty with a damp cloth to remove coffee oil Thereafter refill it with coffee beans 40 ENGLISH DESCALING The descaling process takes approx 35 minutes Lime scale builds up inside the machine during use It needs to be remo ved regularly as it may clog the water and coffee circuit of your machine The machine tells you when descaling is needed If the machine display shows the CALC CLEAN icon it means that you need to descale EE Caution Not doing this wil
22. ine using a soft dampened cloth EJ Make sure the brew group is in the rest position the two reference signs must match If they do not match proceed as described in step 9 EJ Gently pull down the lever until it is in contact with the brew group base and the two reference signs on the side of the brew group do match El Make sure the hook to lock the brew group is in the correct position by firmly pressing the PUSH button until you hear a click Check if the hook is at the top end position If it is not please try again EE Insert the brew group in its seat again until it locks into place without pressing the PUSH button 32 ENGLISH Insert the coffee residues drawer and close the service door Insert the coffee grounds drawer Monthly cleaning of the Cappuccinatore o Every month you need to perform a more thorough cleaning of the PHILIPS Cappuccinatore using the Saeco Milk Circuit Cleaner You can purchase Saeco u Ppa separately the Saeco Milk Circuit Cleaner Please refer to the maintenance product page in this user manual for further details Milk circuit cleaner EF Make sure that the Cappuccinatore is correctly installed Pour the milk cleaner bag into a container Add 1 It of lukewarm water and let it dissolve completely Insert the suction tube in the container STOP Green Yellow Green ENGLISH 33 Place a large containe
23. is automatically adjusting scribed in chapter Saeco Adapting the dose System The coffee grind is too fine Change coffee blend or adjust the grind as explained in chapter Adju sting the ceramic coffee grinder The circuit is not primed Prime the circuit chapter Using the machine for the first time The brew group is dirty Clean the brew group Weekly clea ning of the brew group chapter The dispensing spout is clogged Clean the dispensing spout and its holes VV m Note These problems can be considered normal if the coffee blend has been changed or if the machine has just been installed In this case wait until the machine performs a self adjusting operation as described in chapter Saeco Adapting System 52 ENGLISH ENERGY SAVING Stand b The Saeco full automatic espresso machine is designed for energy saving proven by the Class A energy label After 30 minutes of inactivity the machine turns off automatically If a product has been brewed the machine performs a rinsing cycle In stand by mode the energy consumption is below 1Wh To turn on the machine press I button if power button on the back of the machine is set to I If the boiler is cold the machine performs a rinsing cycle Black Disposal Do not throw away the machine with the normal household waste at the end of its life but hand it in at an official collection point for recycling
24. l ultimately make your machine stop working pro perly and in this case repair is NOT covered by your warranty Yellow Use the Saeco decalcifier only Its formula has been designed to ensure i better machine performance d Saeco mip You can purchase separately the SAECO decalcifier Please refer to the x fa maintenance products page in this user manual for further details FN warning Never drink the decalcifier or any products dispensed until the cycle has been carried out to the end Never use vinegar as a decalcifier Note During the descaling cycle do not switch off the machine If this has happe ned you need to restart the descaling cycle from the very beginning To execute the descaling cycle follow the steps below Before descaling EH Empty the drip tray ENGLISH 41 Remove the Cappuccinatore from the hot water steam wand Remove the INTENZA water filter from the water tank if it was instal led Press the MEW button Press the _ _ button until the following display is shown Yellow EJ Press the button to enter the descaling menu OK 4 tEscALER Ily E l Red Note If you press the button by mistake press the button to quit EJ Remove the water tank and pour the entire content of the Saeco decal cifier Then fill the water tank with fresh water up to the MAX level Place the water tank back into the machine EJ Place a large
25. leaning of the brew group with Coffee Oil Remover a Besides weekly cleaning we recommend running this cleaning cycle with PHILIPS the Coffee Oil Remover after approximately 500 cups of coffee or once saec a month This operation completes the maintenance process of the brew group You can purchase separately the Coffee Oil Remover Please refer to the maintenance products page in this user manual for further details EJ Caution The Coffee Oil Remover tablets are to be used for cleaning only and do not have a descaling function For the descaling procedure use the Saeco descaling solution and follow the procedure described in the Descaling chapter EJ Place a container under the dispensing spout Make sure the water tank is filled with fresh water up to the MAX level 38 ENGLISH Green Put a Coffee Oil Remover tablet in the pre ground coffee com partment Press the A button one or more times to select the pre ground coffee function without adding ground coffee EJ Press the button to start a coffee brewing cycle MEMO EJ Wait until the machine automatically ends the dispensing process Press the D button to turn off the machine and let the solution take effect for approximately 15 minutes Make sure you discard the dispen sed water EJ Turn on the machine and wait until the rinse cycle is completed KJ Remove t
26. nge al Press the C button to exit the programming mode Note The machine will automatically exit the programming mode if the user does not do anything for 3 minutes The function s values that were chan ged but not confirmed won t be saved ENGLISH 47 MEANING OF THE DISPLAY SYMBOLS This machine is equipped with a colour coded system to make the user s understanding of the display signals easier The icons are colour coded according to the traffic light principle Ready Signals Green Colour The machine is ready to brew products The machine is ready to brew pre ground coffee Steam or hot water selection Hot water dispensing Steam dispensing The machine is brewing one cup of espresso The machine is brewing one cup of coffee The machine is brewing two cups of espresso The machine is brewing two cups of coffee 48 ENGLISH Ready Signals Green Colour The machine is programming the amount of coffee to be brewed STOP MEMO Sy Coffee brewing using pre ground coffee in progress Warning Signals Yellow Colour The machine is heating up to brew beverages or dispense hot water The machine is heating up during beverages programming The machine performs the rinsing cycle Wait until the machine has comple ted the cycle The machine needs the INTENZA water filter to be replaced The brew group is being reset due to machine reset Refill the c
27. nt to ensure that you remain satisfied with your machine If not done already please register your product on www philips com welcome so that we can stay in contact with you and send you cleaning and descaling reminders If you need service or support please visit the Philips website at www philips com support or contact the Philips Saeco hotline in your country You find its phone number in the warranty booklet by pa cked separately or on www philips com support 54 ENGLISH ORDERING MAINTENANCE PRODUCTS For cleaning and descaling use Saeco maintenance products only You can purchase these at the Philips online shop at www shop philips com service your local dealer or at authorised service centers If you have any difficulties obtaining maintenance products for your machi ne please contact the Philips Saeco hotline in your country You find its contact details in the warranty booklet by packed separately or on www philips com support Overview of maintenance products Decalcifier CA6700 PHILIPS _ aeco d Decalcifi i INTENZA Water Filter CA6702 PHILIPS Grease HD5061 Coffee Oil Remover CA6704 gt pHILIPS yr Milk Circuit Cleaner CA6705 Maintenance Kit CA 6706 ENGLISH 55 PHILIPS The manufacturer reserves the right to make changes without prior notice www philips com saeco Rev 04 del 15 09 12 15002931
28. offee bean hopper with coffee beans and restart the cycle START Prime the circuit The machine needs to be descaled Press the button to enter the descaling menu Follow the steps described in the Descaling chapter of this manual If you want to descale later press the button to continue using the machine Please note that not descaling your machine will ultimately make it stop wor king properly In this case repair is NOT covered under your warranty ENGLISH 49 Warning Signals Red Colour Close the service door Fill the coffee beans hopper The brew group must be inserted into the machine Insert he coffee ground drawer Empty the coffee grounds drawer and the coffee residues drawer u r Cy Fully insert the coffee ground drawer before turning the machine off t B08 ose Fill the water tank Turn off the machine After 30 seconds turn it on again Try this 2 or 3 times If the machine does not start contact the Philips SAECO hotline in your country You can find its contact details in the warranty booklet by packed separately or on www phi lips com support ije 50 ENGLISH TROUBLESHOOTING This chapter summarizes the most common problems you could en counter with your machine If you are unable to solve the problem with the information below visit www philips com support for a list of frequently asked questions or contact the Philips Saeco hotline in your co
29. ount of water needed for the rinse cycle has been com pletely dispensed this icon on the side is displayed Press the o button to quit the descaling cycle a Pi The machine automatically primes the circuit PA The machine now carries out the warm up and automatic rinse cycle to prepare for product brewing Empty the drip tray and place it back Remove and empty the container PZ The descaling cycle is now completed Place back the INTENZA water filter into the water tank if it was installed and the Cappuccinatore Note At the end of the descaling cycle wash the brew group as described in the Weekly cleaning of the brew group chapter The two rinse cycles are performed in order to have the circuit cleaned with a preset amount of water to ensure proper machine performance If the water tank is not filled up to MAX level the machine might require three or more cycles 44 ENGLISH PROGRAMMING Yellow Yellow Display contrast Yellow Yellow ESC WATER OM FILTER gt OFF 4 Yellow YES DEFAULT ENON SETTINGS Yellow The user can change some of the machine operating settings according to her his preferences Adjustable parameters Coffee temperature This function allows you to adjust the coffee brewing temperature Timer stand by This function allows you to adjust the time until the machine will go into standby mode after the last brewing Contrast
30. r 1 5L under the Cappuccinatore E Press the amp 2 button This icon is displayed Press the button to steam dispensing EJ The following icon may be displayed during the preheating time requi red by the machine WA The following icon will be displayed during the dispensing When the solution is finished press the button to stop dispensing FN warning Never drink the solution dispensed during the procedure EJ Rinse the container thoroughly and fill it with 1 2 It of fresh water to be used for rinsing cycle KJ Insert the suction tube in the container 34 ENGLISH Green Er Yellow STOF ey g M Empty the container and place it back under the Cappuccinatore GE Press the amp button This icon is displayed Press the button to steam dispensing EP The following icon may be displayed during the preheating time requi red by the machine EE The following icon will be displayed during the dispensing When the water is finished press the button to stop dispensing MEMO Wash all the Cappuccinatore parts by following the instructions below ES Remove the suction tube iT Remove the Cappuccinatore from the machine ENGLISH 35 Remove all the parts shown in the picture KEJ Wash all the parts with lukewarm water EE Make sure that any milk residues are removed from the slot of the cou pling see arrow in the imag
31. s needed Not doing this will make your appliance stop working properly In this case repair is not covered under your warranty e Donotkeep the machine at temperature below 0 degree Celsius Residue water in the heating system may freeze and cause damage e Donot leave water in the water tank when the machine is not used over a longer period of time The water can become contaminated Use fresh water every time you use the machine Compliance with standards The machine complies with art 13 of the Italian Legislative Decree dated 25 July 2005 no 151 Implementation of the directives 2005 95 EC 2002 96 EC and 2003 108 EC on the restriction of the use of certain hazardous substan ces in electrical and electronic equipment as well as waste disposal This machine complies with EU directive 2002 96 EC INSTALLATION Product overview ENGLISH 7 General description Grinder adjustment knob Pre ground coffee compartment Coffee bean hopper Coffee bean hopper lid Control panel Dispensing spout Cup holder grill Full drip tray indicator Drip tray 10 Coffee grounds drawer 11 Brew group 12 Service door 13 Grease for the brew group 14 Power cord 15 Cappuccinatore 16 Suction tube 17 Water tank 18 Power cord socket 19 Power button 20 Coffee grinder adjustment key Pre ground coffee scoop 21 Cleaning brush 22 Coffee residues drawer 23 Water hardness test 24 Espresso brew button 25
32. s plug the mains cord or the machi ne itself is damaged Do not make any modifications to the machine or its mains cord Only have repairs carried out by a service centre authorized by Philips to avoid a hazard This machine is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of expe rience and knowledge unless they have been given supervision or instruction concerning use of the machine by a person responsible for their safety Children should be supervised to ensure that they do not play with the machine Never insert fingers or other objects into the coffee grinder ENGLISH 5 Caution e The machine is for household use only It is not intended for use in en vironments such as staff kitchens of shops offices farms or other work environments e Always put the machine on a flat and stable surface e Donot place the machine on a hot plate directly next to a hot oven heater or similar source of heat e Only put coffee beans into the coffee bean hopper If ground coffee instant coffee or any other substance is put in it may damage the machine e Allow the machine to cool before putting on or taking off e Never use warm or hot water to fill the water tank Use cold water only e Never clean with scrubbing powders or harsh cleaners Simply use a soft cloth dampened with water e Descale your machine regularly The machine indicates when desca ling i
33. snwvais 53 GUARANTEE AND SERVICE ssinisisissccsveisersssisaevesccineceanessitascsvenievuaniananernvianccies 53 Guarantee eerca E eect ect cet reece eee ee 53 Cgc cess E A E E aceteteneeae eats 53 3 4 ENGLISH IMPORTANT S afety instructions This machine is equipped with safety features Nevertheless read the safety instructions carefully and only use the machine as described in these instructions to avoid accidental injury or damage Keep this user manual for future reference yN The term WARNING and this sign warn against possible severe injuries danger to life and or damage to the machine EE The term CAUTION and this sign warn against slight injuries and or dama W ge to the machine arnin Connect the machine to a wall socket which is properly wired Its main voltage should comply with the technical data of the appliance Do not let the mains cord hang over the edge of a table or counter or touch hot surfaces Never immerse the machine mains plug or mains cord in water dan ger of electrical shock Never direct the hot water jet towards body parts danger of burning Do not touch hot surfaces Use handles and knobs Remove the mains plug from the wall socket Ifa disturbance occurs Ifthe machine will not be used for a long time Before cleaning the machine Pull on the plug not on the mains cord Do not touch the mains plug with wet hands Do not use the machine if the main
34. ssanensnensssssssssssss 18 Adjusting the aroma coffee strength ssssscssessssssessecssessesssesssessessecsssssnessessscssesssessscssecsesssesaneeseesses 19 Adjusting the dispensing SOUT savas actives se canacasadit icivasd kaa sacessten vdehvass cous dcanensetehendaiiteed Wactvmnasseaaen 20 Adjusting the coffee length ssszsiscesscsasasssucsnsaiansiavessdudiseysnnecassaavessteathaginecenntsassaniasiiansaivonveasaniauicaigenns 21 ESPRESSO AND COFFEE BREWING sssccsssssscssssssccsssssccssssssccesssssscesssesesesees 22 Espresso and coffee brewing using coffee DeANS sescssssssscssscssesssssssscssscsessssssssscsescssssssessssesesesesesss 22 Espresso and coffee brewing using pre ground coffee ssssssssssssssssssssssssssssssssssssssssssssssssssssessesssssssssss 23 CAPPUCCINO BREWING jcsiscessscessstincsncecesavisoacessiovdinavassdentsensheiassbesstzebstedtantanads 24 HOT WATER DISPENSING scccscassoissssiussasceisctaczcsvebasinavaneiseasusClecasasvevcaiatvesssensavinn 25 CLEANING AND MAINTENANCE ccsssssssssssssccsssssccsssssccccsssscsscsssscscsssesssees 27 Daily cleaning of th WO MMII sensies 27 Dany cheanii or the Wer TaK iiaiai N 28 Daily cleaning of the Cappuccinatore sssssecssessssesssesssessessecsssssssessucssssssscssscssscssuesssesssessscssnecsscessesses 28 Weekly cdeaning of the machine si sisiascxsssesatansessssnsdinetnsecusnsentasaceressdisseavsivnnn nan aoetannnnbnismintonietanicanndean 29 We
35. tainer under the dispensing spout Check that the machine shows this display Q 2s Green uO Select the pre ground coffee brewing function by pressing the button The machine shows this display Note Do not add pre ground coffee into the compartment Q Green Press the button The machine starts dispensing water MEMO EJ When the dispensing has finished empty the container Repeat the operations from step 1 to step 4 twice then continue with step 6 EJ Remove the pin with the suction tube from the Cappuccinatore Place a container under the Cappuccinatore Green Red Q T Qs Green ENGLISH 13 EJ Press the 4 button The following icon is displayed EJ Press the button to start dispensing hot water Ef Dispense water until the no water icon appears EE At the end fill the water tank again up to the MAX level Now the ma chine is ready for brewing coffee You will see the display as shown at the left Place the pin with the suction tube back into the Cappuccinatore Note When you haven t used the machine for 2 or more weeks the machine will automatically perform an automatic rinse self cleaning cycle after you switch it on Thereafter you need to initiate the manual rinse cycle inclu ding brewing a coffee as described above The automatic rinse self cleaning cycle is also initiated automatically when starting up the machine wi
36. th cold boiler when the machine is preparing to go into stand by mode or after you have pressed the D button after a coffee has been brewed 14 ENGLISH Intenza Aroma System Machine water hardness setting Yellow Yellow Measuring and programming water hardness Measuring water hardness is very important for defining the frequency in which the machine has to be descaled and to install the INTENZA water filter for more detail on the water filter see next chapter To measure the water hardness follow the steps below GB immerse the water hardness test strip supplied with the machine in water for 1 second Note The test strip can only be used for one measurement Wait for one minute Check how many squares have changed the colour to red and then consult the table Note The numbers on the water hardness test strip correspond to the water hardness adjustment settings More precisely 1 1 very soft water 2 soft water 3 hard water 4 very hard water The letters correspond to the references that are located at the base of the INTENZA water filter see next chapter for this EJ Now you can program the water hardness setting Press the Quy button and scroll the pages by pressing the _ _ button until the following icon is displayed gt Note The machine is supplied with standard water hardness setting suitable for most of the type of water
37. ts parts in the dishwasher Donotimmerse the machine in water Do not use alcohol solvents and or abrasive objects to clean the machine Donotdry the machine and or its components using a microwave and or standard oven EJ Empty and clean the coffee grounds drawer daily with the machine turned on Other maintenance operations can only be carried out when the machine is turned off and unplugged Empty and clean the coffee residues drawer located inside of the ma chine Open the service door remove the coffee residues drawer and empty the coffee residues 28 ENGLISH Se EJ Empty and clean the drip tray Perform this operation also when the full drip tray indicator is raised AM SS i Daily cleaning of the water tank IE Remove the small white filter or the INTENZA water filter if installed from the water tank and wash it with fresh water Put the small white filter back or the INTENZA water filter if installed in its housing by gently pressing and turning it at the same time Fill the water tank with fresh water Daily cleaning of the Cappuccinatore It is important that you clean the cappuccinatore daily or after each use as it preserves hygiene and ensures perfect milk froth consistency Each time after frothing milk you need to GB Insert the suction tube in a container filled with fresh water STOP Yellow Green Green ENGLISH 29 Place an empt
38. untry You find its contact details in the warranty booklet by packed separately or on www philips com support Machine actions Causes The machine does not switch The machine is not connected to on the electric network Sometimes water is drained auto matically by the machine into the drip tray to manage the rinsing of the circuits and ensure optimum machine performance The drip tray gets filled al though no water is drained The coffee grounds drawer was a 6 The red gx icon is always emptied with the machine off displayed on the machine Coffee is not hot enough The cups are cold The hole of the steam wand is clogged No hot water or steam is dispensed The Cappuccinatore is dirty if supplied The blend is unsuitable coffee is not freshly roasted or the grind is too coarse Coffee does not have enou gh crema See note The machine takes a long time to warm up or the amount of water dispensed from the wand is too little The machine circuit is clogged by limescale The brew group cannot be removed The brew group is out of place The coffee grounds drawer is inserted There is alot of ground coffee Coffee is not suitable for automa under the brew group tic machines Solutions Connect the machine to the electric network This is seen as normal machine behavior The coffee grounds drawer must always be emptied with the machine on Wait until the J icon is displa y
39. upply cord or extension cord is used l The marked electrical rating of the detachable power supply cord or extension cord should be at least as great as the electrical rating of the appliance 2 It the appliance is of the grounded type the extension cord should be a grounding type 3 wire cord and 3 The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over Congratulations on your purchase of a Saeco Intelia Class full automatic espresso machine To fully benefit from the support that Saeco offers please register your product at www philips com welcome This user manual applies to HD8752 The machine is suitable for preparing espresso coffees using whole coffee beans It can also dispense steam and hot wa ter In this user manual you will find all the information you need to install use clean and descale your machine ENGLISH CONTENTS IMPORTAN iivtrscniinindinaicnnnnninniminn oan A BOWL UPS MIC TION r A E E E AN OT 4 Wann ericae eia nai a A A AE RES 4 ETO P E AE 5 Compliance with standards esssssosoessssensssssesoosssssssetoonssssserereonnsssseronoonssssseronnssssnssteonossssnssreonnssssereree 5 INSTALLATION sestssessiscisssatnctussstacivshsnsedcdeuscbncscciansdussadvisessaassuasstuascancussietosiuansts 6 PPO CUCL OVEN VEW sssctunortceasesasaiselusieteasledecxcsphieteonctas sss ieviaieascaonco iLE ta N rE Cau y EEEn E
40. use pre ground and decaffeinated coffee With the pre ground coffee function you can only brew one coffee at a time EM Press the E button to select the pre ground coffee function Lift the pre ground coffee compartment lid and add one scoop of pre ground coffee to the compartment Use only the measuring scoop supplied with the machine Then close the pre ground coffee com partment lid PN warning Add only pre ground coffee to the pre ground coffee compartment Other substances and objects may cause severe damages to the ma chine Such damages are not covered by your warranty uw MEMO Press the button for an espresso or button for a coffee The MEMO brewing cycle starts After the pre brewing cycle coffee begins to pour out of the dispen sing spout EJ Coffee brewing stops automatically when the pre programmed level is reached it is possible to stop earlier by pressing the button MEMO After brewing the product the machines returns to the main menu Repeat the steps described above to brew more coffees using pre ground coffee Note If no pre ground coffee is poured into the compartment only water will be dispensed If the dose is excessive and 2 or more measuring scoops of coffee are used the machine will not brew the product Only water will be dispensed and any ground coffee will be discharged into the coffee grounds drawer 24 ENGLISH CAPPUCCINO BREWING z
41. y container under the Cappuccinatore Press thee amp ep button This icon is displayed Press the button to select steam MEMO EJ The following icon may be displayed during the preheating time requi red by the machine EJ The following icon will be displayed during the dispensing phase Dispense water from the Cappuccinatore until clear water is dispensed Press the button to stop dispensing MEMO Clean the suction tube with a damp cloth Weekly cleaning of the machine EB Clean the seat of the drip tray Clean the pre ground coffee compartment with the cleaning brush 30 ENGLISH Weekly cleaning of the brew grou The brew group should be cleaned every time the coffee bean hopper is filled or at least once a week EH Turn off the machine by pressing the I button and remove the plug from the socket Remove the coffee grounds drawer Open the service door Remove and clean the coffee residues drawer EJ To remove the brew group press the PUSH button and pull it by the handle Q Fi RE a J 3 4 pho Fa T We l y E ll ii i gt S y EJ Thoroughly wash the brew group with fresh lukewarm water and carefully clean the upper filter i Caution Do not use detergent soap to clean the brew group q SA ENGLISH 31 EJ Let the brew group air dry thoroughly WA Thoroughly clean the inside of the mach
Download Pdf Manuals
Related Search