Zalman LQ1000
Contents
1. CPU Water Block e The specifications of any product may change without prior notice to improve performance 5 Leakage Inspection and Test Run 5 1 Adding Coolant 1 Remove the Reservoir Cap by turning counter clockwise 2 Mix half 125cc of the provided coolant 250cc with 500cc of distilled water in a container 3 Secure the Funnel in the Pouring Hole and carefully pour coolant up to the Reservoir Window s High Level mark Note 1 Please prevent coolant spillage by carefully pouring with the provided Funnel Coolant Level will drop when the coolant begins circulating please pour additional coolant up to the High Leve mark Note 2 The provided coolant is a concentrated liquid please dilute the coolant with distilled water in a 1 4 ratio Note 3 Read the warning label on the coolant s container prior to use Note 4 Keep the LQ1000 and its components away from children Funnel Pouring Hole High Level High Level Reservoir Window 5 2 Coolant Circulation 1 To provide the necessary power 12V DC for your Test Run and Leakage Inspection please disconnect the PSU s Main Connector 20P 24P and 4 Pin CPU ancillary connector from the motherboard and use the provided Jump Cable to2. bag TREME HTBRIO TOD GOOLING ta Fij WOU L Wi a HW ng zo M SMET MN Wh i ZALMAN WWW ZALMAN CON aU English Version Visit our website and watch the Z Machine LQ1000 installation video for an installation overview x Please read this manual thoroughly before installation x The specifications of this product and its components may change without prior notice to improve performance http www zalman com Notes Installation Notes 1 Check the condition of the product and its components before installation If there is a problem with the product and or its components please contact the retailer for replacement 2 Keep this unit away from heat sources such as direct sunlight as well as from water oil and humidity Place the unit on a flat stable and well ventilated area 3 Do not drop or subject the unit to excessive force 4 Do not mix any contaminants with the coolant when filling It may cause product failure or corrosion 5 Check the manual when connecting cables Incorrect connections can lead to fire resulting from short circuiting 6 Check for leaks on the Water Blocks and Tubes before installation 7 Preparing the necessary tools Needle Nose Pliers Scissors will ease the installation process Operational Notes Check to see if the DC cables are properly connected before use 2 Avoid inserting any objects into the system while the powe
3. RESET A long press for at least 5 seconds resets the cooling system e The specifications of any product may change without prior notice to improve performance 16 Zalman Computer Noise Prevention System Stable performance and a noiseless liquid cooling system can both be achieved with the use of Zalman s Ultra Quiet Power Supply VGA Water Block Northbridge Water Block and Super Thermal Grease Northbridge Water Block Super Thermal Grease Dual Heatpipe Cooled Modular Power Supply ZM850 HP ZM1000 HP e Dual Heatpipes Installed for Maximum Cooling Performance and Ultra Quiet Operation e Improved Power Factor 8 Reduced Harmonics through Active PFC e High Efficiency Design and 80 PLUS Certified e Supports ATX12V CPU 4 Pin and EPS12V CPU 8 Pin e Gold Plated Terminals amp 16AWG Wires HTPC Enclosures e Designed for High TDP Processors e Designed for High Performance Power Supplies Designed for Optimal Graphic Card Performance e Designed to Maximize HDD and LCD Lifespan e The front panel DFSTN LCD provides user access to various features such as the Graphic Equalizer Volume Power HDD Operation Time etc 160XT PLUS e Sliding HDD and ODD Chassis provide easy installation and removal For more information please visit our website e The specifications of any product may change without prior notice to improve performance
4. 5 Leakage Inspection and Test Run eee ee ka akt n s t mop een aste sy tp a en kep ECT eee 13 1 Specifications Enclosure Dimensions L x W x H 480mm X 220mm X 450mm Weight 15kg 33lb Material Aluminum Alloy Motherboard Compatibility Standard ATX microATX PSU Compatibility Standard ATX ATX12V USB Port x 2 IEEE1394 Firewire Port x 1 Fronti Po Headphones x 1 MIC x 1 PCI AGP Card Compatibility Full Size Drive Bays 3 5 Bay x 5 5 25 Bay x 4 Water Tank Reservoir Dimensions L x W x H Weight 800g Material Aluminum Alloy Acrylic Coolant Capacity Max 300cc Water Pump Power Consumption GW DC 12V Maximum Flow Rate 300l hr 220mm Fan Dimensions L x W x H 220 L x 220 W x 30 H mm Bearing Type 2 Ball Bearing Fan Speed Min Max 550rpm 10 850rpm 10 CPU Water Block ZM WB5 Dimensions L x W x H 63 L x 63 W x 40 H mm Weight 160g Material Cover Aluminum Alloy Base Pure Copper Coolant ZM G300 Material Propylene Glycol amp Anti Corrosion Agent Volume 250cc Freezing Point 9 C Replacement Cycle 1 Year e The specifications of any product may change without prior notice to improve performance 2 Parts List 2 1 Front View 5 25 Bay 3 5 Bay PC RESET Button POWER Button I O Port SYSTEM LED HDD LED FAN SPEED Gauge FLOW RATE Gauge FND Gauge VOLUME KNOB Cooling System LED RESET Button AUT
5. connect the Main Connector s 20P 24P green wire terminal to a black wire ground terminal 2 Connect the Display PCB s 4 Pin power connector and the PSU s 4 Pin connector 3 When power is supplied the front panel display gauges will light up red and the Left Door Flow Indicator will light up blue with a spinning impeller 4 For discharging of gas and good coolant circulation turn the Power Supply ON OFF approximately 3 7 times at 10 second intervals 13 e The specifications of any product may change without prior notice to improve performance 5 Check for leakage at each inlet outlet Leakage can lead to short circuiting and or damage to the motherboard or other components If leaking is discovered turn OFF the power completely remove any leaked coolant and reassemble the leaking section 6 Coolant Level will drop when the coolant begins circulating Please pour additional coolant up to the Reservoir Window s High Level mark 7 After degassing is complete detach the PSU s power connection Use a coin like object to secure the Reservoir Cap to prevent leaking 8 Lay the LQ1000 on its right side 9 Reinstall the Water Block that were removed from the motherboard for degassing 10 Connect the PSU s Main Connector and the CPU 4 Pin Connector to the motherboard 11 To prevent coolant leakage the LQ1000 Must be set upright on its feet before proceeding with the next step 12 12 After setting the LQ1000 upright
6. join with the Tube Nipple from of step 3 6 After the Silicone Tube installation is completed please check for tensile forces in the tube by repeatedly opening and closing the side panel Please adjust the Tube length to prevent tension in the Tube 7 If optional VGA Northbridge Water blocks are please repeat the tension test and adjust Tube the length as needed Note 1 Please do not apply Thermal Grease or Pads when installing waterblocks Note 2 Please refer to each product s manual when installing VGA Northbridge waterblocks Tube Clamp 4 l A x With CPU Water block installed alone x VGA Water Block installed with CPU Water Block e The specifications of any product may change without prior notice to improve performance 4 10 Installation Troubleshooting Refer to the diagram below as a reference for the coolant s circulation path order Water Pump CPU Water Block N B Water Block lt Optional gt Reservoir Left Door Radiator VGA Water Block T
7. on its feet remove the Sealing Bolt from the Reservoir Cap and secure the Sealing Bolt in the adjacent Sealing Bolt Tap Hole Note Cable organization is necessary to prevent interference with tubes when the Left Door Black Wire 4 Pin Connector M mi SL Main Connector ny Green Wire 4 Power Supply lt lt 4 Pin Connector _ lt Motherboard Power Jump Cable Connector 8 PLA llu Sealing Bolt Tap Hole p High Level aa wee ae Reservoir Cap e The specifications of any product may change without prior notice to improve performance 14 CED ee Sealing Bolt 5 3 220mm Fan Installation 1 Install the provided 220mm Fan and Ffan Grill as shown in the diagram below 2 Connect the 220mm Fan s 3 Pin Connector to the Black 3 Pin Connector 3 After the Fan is installed please be cautious to prevent inference between or among Tubes and or cables J gt s 220mm Fan Stand Off p Moz No Fan Grill 0 w Fan Fixing Bolt 120mm Rear Fan 3 Pin Connector 220mm Fan 3 Pin Connector Black PCB 3 Pin Connector for 220mm Fan Performance Tip x When not using the 220mm fan Make sur
8. on the Power Bracket and screw the four Bolts Bolt PHM 6 32 10 Black from outside the enclosure s 4 2 Pump Bracket Removal To prevent damage to the unit during transport the Pump Bracket is removed Note The Pump Bracket can cause unwanted noise if not removed 4 3 CPU Water Block ZM WB5 Guide Install Before installing the motherboard please refer to ZM WB5 s manual for correct socket installation procedures Note Intel CPU users please refer to the CPU waterblock s manual for installation Water Pump _ gt Bracket Water Pump a Back plate for Socket 775 ex Intel Pentium 4 Socket 775 installation r e The specifications of any product may change without prior notice to improve performance 4 4 Motherboard Installation Secure the motherboard to the enclosure then install components CPU VGA RAM etc onto the motherboard FT a Clip Support for Socket 775 4 5 3 5 5 25 Drive Installation 1 Remove the Bay Covers of the 3 5 FDD bay and the 5 25 ODD bays 2 Insert the ODD into desired 5 25 bay and fix it in place with the Tool Free Bolts 3 ODD Slot 3 amp 4 and the FDD Slot require using Fixing Bolts Bolt M3x5 to secure dri
9. O MANUAL Button C F Button e The specifications of any product may change without prior notice to improve performance 2 2 Side View Water Tank Reservoir Tool Free Bolt Reservoir Cap 120mm Fan Oo oO Reservoir Window ANAK Radiator Silicon Tube Tube Nipple 220mm Fan Install Tap Hole Left Door Tool Free HDD Bay Water Pump e The specifications of any product may change without prior notice to improve performance 3 Components 1 Enclosure 5 Funnel eer fi A 6 Silicone Tube 1m lt gt 3 Jump wa 4 Anti Corrosion Coolant ZM G300 a N a 10 Bolt Parts onl Assembly Allen Screw Outer Chassis KX 0 Optional Fan Stand Off M3 28 3 3 Optional Fan Install 2 4 4 C osn eeo o rors Hand Bolt P9 15 4 HDD Installation e The specifications of any product may change without prior notice to improve performance 4 Installation Guide 4 1 Power Supply Installation Unscrew the four Bolts Bolt FH M3x6 as shown in the diagram to open the Doors Place the PSU
10. e the side panel is securely closed for a quiet computing environment Sealing off the I O cover and PCI Bracket with tape etc will optimize the cooler s performance TI ANT 1 0 Cover PCI Bracket 15 e The specifications of any product may change without prior notice to improve performance 5 4 Front Panel Display D Fan Speed Gauge Display the 120mm Rear Fan s rotation speed in real time FND Flexible Numeric Display Temperature Display Coolant Temperature upper display Ambient Temperature lower display Coolant Level Sensing If the coolant level drops below a threshold level an alarm will sound and the display will flicker Please refill with coolant if the display flickers Coolant Temperature Sensing lf the coolants temperature reaches above 60 C 92 F an alarm will sound and the FND Display will flicker If the flickering is observed please check for problems 3 Coolant Flow Rate Gauge Displays the coolant s flow rate in real time Control Knob Controls the Fan Speed and Coolant Flow Rate Temperature Mode Button Sets the temperature display to Celsius C or Fahrenheit F AUTO MANUAL Button AUTO Mode Automat fan speed and coolant flow rate MANUAL Mode Allows the user to manually adjust fan speed and coolant flow rate 7 LED RESET Button LED On Off A short press turn the displays LED s On amp Off
11. r is ON It may be harmful for the user and product 3 If the coolant is not circulating properly or if the pump s flow rate becomes too low for other reasons the red LED will begin to flicker with an alarm sound Immediately turn the system OFF and contact the place of purchase 4 Must use the provided coolant Regularly check the amount of coolant and replenish as needed replacement cycle of the ZM G300 coolant is 1 year 5 If a leak is found turn off the system immediately and contact the place of purchase 6 Do not block the Air Ducts on either side of the product This can lead to fan failure increased noise or a decrease in product performance 7 Make sure that the Water Pump is functioning properly Disclaimer Zalman Tech Co Ltd is not responsible for any damages due to external causes including but not limited to improper use problems with electrical power accident neglect alteration repair improper installation or improper testing e The specifications of any product may change without prior notice to improve performance 2 Table of Contents 1 Specifications n E a n eters ec gi oes ce ee a e a pcs hence crs es nee ni eee e e ko n mp tre eee 3 2 Pans VIG li r n vie letan E gets ky te a ot ee on Eb ap ot a l n tee e 4 3 Components Seas E geet cig ee E e Sa a a es owe psp eee eee esa ede hee ea ec a Se a kk oo sa ee 6 4 Installation Guide EE eee ee CR eee eee ey ee eT nT ene RT eT ee ee ee eet Cree ae 7
12. ube Nipple lt Optional gt 4 11 Water Block Removal 1 To allow adequate degassing please disassemble the Waterblock s from the motherboard as shown below 2 Skipping procedure will prevent adequate degassing due to internal pressure within the Tubes Note Please place the Waterblock s at or below the height of the pump for the degassing procedure
13. ves P sit 30DD ra Slot 4 ODD FDD Slot ODD Bay Cover pal FDD Bay Cover e The specifications of any product may change without prior notice to improve performance 4 6 Hard Disk Drive Installation 1 Open raise to unlock the HDD Lock Bar of the desired HDD Chassis Bay 2 Slide HDD into desired Bay and close lower to lock the HDD Lock Bar behind the HDD 3 To remove the HDD open roll up the HDD Lock Bar above the HDD 4 For transportation lower the HDD Lock Bar and secure with Hand Bolts as shown below AN A A A Fixing Tap Hole Hand Bolt Lock B Lock Groove ikid Note1 Excessive pressure may damage the HDD Lock Bars Please take caution during HDD installation and removal Note2 Reverse the procedure for removal e The specifications of any product may change without prior notice to improve performance 4 7 Cable Connection Button PCB Improper connection of the Power LED and HDD LED can lead to LED malfunction Please refer to your motherboard s manual before making cable connections RESET HDD2 HDD1 POWER LED POWER 4 8 Front I O Connection Certain motherboards have different configurations for the IEEE1394a USB2 0 and audio connectors from the one shown in the diagram below Please refer to
14. your motherboard s manual er I O Port PCB TEEE1394 USB 2 0 Bacos Boone 58000 pewon Cocos 0000S DEODO a nn GND E MIC IN_L MM GND MIC MM GND 12V 12V GND M M GND MIC IN_R PRESENCE MIC 5V Ml KEY TPBO M Mi TPBO D E ml D SPK OUT_R M SENSE RT SPK OUT_R i M RETURN_R GND MM GND D D SENSE SEND M KEY_BL KEY KEY_BL TPAO W M TPAO vcc mm vcc SPK OUT_L M Mi SENSE2_RT SPK OUT_L W M RETURN L Motherboard Motherboard Motherboard Motherboard IEEE1394 Dual USB AZALIA HD AC 97 Port Port Audio Port Audio Port Note Improper connections of the IEEE1394 connector and or USB2 0 connector to the motherboard can result in irreversible damage so please refer to both the product and your motherboard s manual prior to installation e The specifications of any product may change without prior notice to improve performance 4 9 Silicone Tube Connection 1 Please refer to the manual included with the CPU waterblock ZM WB35 for installation guides 2 The user can add optional VGA and Northbridge waterblocks 3 Use Needle Nose Pliers to loosen and pull back the Tube Clamp on the tip of the Tube connecting the Water Pump s outlet to the Tube Nipple then disconnect the Tube from Tube Nipple 4 Connect the tip of the disconnected Silicone Tube to the Inlet of the CPU Water Block and secure with the Tube Clamp 5 Use the separately provided tube to connect the CPU Waterblock s outlet and
Download Pdf Manuals
Related Search