Chief KFA325B
Contents
1. Europe Asia Pacific gt TH VU Pn UP Tl U Installation Instructions 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 cO 45 STCONSUMER2. INSTALLATION INSTRUCTIONS KFA 220 225 KFA 320 325 Carts and Stands Horizontal Array Accessory a CHIEF KFA SERIES Our Mounts Your Vision KFA SERIES DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief amp and Centris a registered trademarks of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory w
3. arranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component Installation Instructions WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of the displays installed does not exceed 70 Ibs 31 8 kg for the KFA 220 and KFA 225 and 90 Ibs 40 8 kg for the KFA 320 and KFA 325 The weight of each individual display must not exceed 35 lbs 15 9 kg for the KFA 220 and KFA 225 or 30 los for the KFA 320 and KFA 325 WARNING RISK OF ELECTRIC SHOCK Using the wrong screws could result in severe personal injury or damage to your display If your display uses a longer screw size than those included in the kit DO NOT use the screws provided with the kit Use the screws provided with your display or contact the manufacturer WARNING Improper installation can result in serious personal injury Make sure that the mounting surface can support a redundant weight factor five times the total w
4. eight of the equipment If not reinforce the mounting surface structural members before installing the mount WARNING Be aware of the potential for personal injury or damage to the unit if it is not adequately mounted WARNING The installer is responsible for verifying that the mounting surface to which the KFA is anchored will safely support the combined load of all attached components or other equipment WARNING Watch for pinch points Do not put your fingers between movable parts WARNING Make sure the mount is correctly oriented KFA SERIES Installation Instructions 220 DIMENSIONS KFA 225 DIMENSIONS KFA Installation Instructions KFA SERIES 320 DIMENSIONS KFA 325 DIMENSIONS KFA Installation Instructions KFA SERIES LEGEND Tighten Fastener Pencil Mark Befestigungsteil festziehen Stiftmarkierung fg Marcar com l pis Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Phillips Screwdriver Adjust Kruiskopschroevendraaier Afstellen Tournevis pointe cruciforme Ajuster Open Ended Wrench Remove Llave de boca Quitar uar Ef eer c By Hand Optional Hex Head Wre
5. mounting rail See Figure 9 NOTE Repeat previous steps for each additional display 8 Install end locks into mounting rail using the 5 32 hex key H See Figure 10 Array Rail Figure 9 KFA SERIES End Lock End Lock Retaining Screw Centris Head Figure 10 Display Adjustment These pivot arrays allow horizontal pitch roll and yaw adjustment of each display with a maximum pitch range of 15 up and 15 down These pivot arrays also allow a full 360 deg of display roll Display Horizontal Position Adjustment To adjust display horizontal position 1 Loosen Centris bracket rear adjustment knob See Figure 11 2 Slide Centris bracket with display left or right until properly positioned on array rail 3 Tighten Centris bracket rear adjustment knob Figure 11 Display Pitch Roll and Yaw Adjustment To adjust display position 1 Loosen Centris bracket front adjustment knob See Figure 12 2 Tilt display up or down or adjust display roll left or KFA SERIES right until properly positioned 3 Tighten Centris bracket front adjustment knob Figure 12 10 Installation Instructions Installation Instructions KFA SERIES 11 KFA SERIES a CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8834 000011 REV 01 2010 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 04 10 USA International
6. nch Security Wrench m amp KFA SERIES Installation Instructions TOOLS REQUIRED FOR INSTALLATION 5 32 included refer to Table 1 for quantities and part descriptions Installation Instructions Table 1 Parts n Quantity varies depending upon the number of displays being mounted Installation 1 Determine proper pole clamp to use for installation If mounting to wide portion of pole mount use large pole clamp bracket K If mounting to extendable upper portion of mount use small pole clamp bracket J See Figure 1 Figure 1 KFA SERIES NOTE If removing existing head assembly from cart stand do so prior to installing KFA Series arrays IMPORTANT The KFA Series arrays can be used in addition to the existing head assembly as long as the overall weight limit of the cart stand is not exceeded 2 Attach pole clamp bracket J or K to pole mount front using two 1 4 washers L and two 1 4 20 x 3 4 button head cap screws M See Figure 2 3 Secure pole clamp bracket J or K to pole mount front and pole by tightening two button head cap screws M using a 5 32 hex key H See Figure 2 Figure 2 Display Installation Attach Centris Head to Flush Mount Display AA CAUTION If display uses a screw size other than those included in the kit DO NOT use the screws provided Using the wrong screws could result in damage to your monitor 1 Install two M4 x 12mm Philli
7. ps pan head screws C into two upper mounting holes in display back See Figure 3 NOTE DO NOT fully tighten at this time 2 Hang display on Centris head See Figure 4 3 Install bottom two M4 x 12mm Phillips pan head screws C through Centris head mounting holes and into lower mounting holes in display back 4 Tighten four M4 x 12mm Phillips pan head screws C See Figure 5 KFA SERIES Array Rail Figure 5 Installation Instructions Attach Centris Head to Recessed Mount Display CAUTION If display uses a screw size other than those included in the kit DO NOT use the screws provided Using the wrong screws could result in damage to your monitor 1 Uninstall end lock using the 5 32 hex key H See Figure 6 2 Remove Centris head from mounting rail See Figure 7 Centris Head Square Nut S671 End Lock Array Rail Centris Head Figure 7 3 Place display face down on aclean dry surface 4 Place four 3 4 or 3 8 nylon spacers E or F over four mounting holes in display back NOTE Refer to Table 1 to select the applicable screw and spacer combination 5 Align Centris head mounting holes with four nylon spacers 6 Secure Centris head to display using four M4 x 20mm Phillips pan head screws G or four M4 x 30mm Phillips pan head screws D See Figure 8 Installation Instructions Centris Head Figure 8 7 Slide display with Centris bracket onto
Download Pdf Manuals
Related Search