Sima XL-72 projection screen
Contents
1. See Photos Below 8 You are now ready to attach the screen using the Velcro patches Please see instructions for attaching the screen to the frame further on in the instruction manual Note When Using the Screen Outdoors e The dark colored material from which the Inflatable Theater Frame is construction tends to absorb the heat from the sun which causes the air inside the frame to warm up and expand if the screen is used on a sunny day If the frame is left out overnight the air inside the frame will cool and contract which may cause the frame to sag slightly The sagging is not due to the frame losing air and can be corrected by topping off the frame with air prior to use e It is recommended to keep the supplied air pump on hand to add additional air when using the XL 72 Theater during an all day event e Be sure to deflate frame and store after usage Page 7 Screen Installation Velcro patches are located at each corner and around the perimeter of the screen frame The screen also has a series of Velcro patches for easy attachment Starting with a top corner attach the screen using the Velcro patches Continue to attach the screen across the top of the inflated frame pulling it taut Continue to attach each of the sides again pulling the screen taut between each Velcro connection Smooth the screen and attach the bottom Velcro patches Page 8 Setting up the Inflatable Home Theater for Front and Rear2. Projection Projector Distance Projector Angle e Typically set up the projector a distance 1x 1 5x the diagonal from the screen e In general for a 16 9 screen ratio use 1 15x the diagonal for projector distance For 4 3 screen use 1 25x e Follow the projector manufacturer s instructions 12 Diagonal 8 Diagonal 6 Diagonal e Attempt to position the projector so that it is parallel to the inflatable screen e Care should be taken so that the projector is aligned both horizon tally and vertically to the front of the inflatable screen e If your projector has a keystone adjustment feature this may be used to correct for the angle Page 9 Securing the screen and filling the water ballasts Inflate the spare set of pontoons using the include pump The spare pontoons contain water ballasts to weight and secure the inflated screen Locate the clear plastic water intake cap Note the air intake valve has a black threaded cap the water intake is clear plastic FIG 7 Carefully pour suggest using a funnel the water into the ballast Standard tap water can be used FIG 8 Each ballast holds approximately 2 Gallons of water Fill to 1 gallon recomended Make certain the cap is securely closed when finished FIG 7 FIG 8 The spare pontoons are easily attached to the screen frame pontoons using the provided straps Page 10 Screen Deflation and Repacki
3. Sima XL 72 Theater Inflatable Indoor Outdoor Projection Screen 2sm www simaproducts com Table of Contents TABLE OF CONTENTS EE ALETE EEN NE E N E V E AA E E E A EE tee 2 INTRODUC HON atispan N dalle esos sodas aw does cri alc E E EAA 3 LS TORMATERIA E Sirie ea e EOE ETE EA A ENEEIER EROE ON 4 SELECTING A SE TOP S ME mea a E chee N N T ee ee ete 4 UNPACKING THE SCREEN sristi UAE E anes EET erate OE NET NNE NNA 5 INELATING THE SCREEN isoina e E E weed io O tanininesits 5 6 7 SCREEN INSTALLATION WITH VELCRO PATCHEG sssssssssssssesssesecsrsssssssssssssasscssnenesenssecssosoessosscasasssaesesenesesoes 8 SETTING UP THE INFLATABLE HOME THEATER FOR FRONT AND REAR PROJECTION eeeeeeeees 9 SECURING THE SCREEN AND FILLING WATER BALLASTS u ee csesesececeseceseseescecscsessseesseecseseeeseeneneeeseneees 10 SCREEN DEFLATION S REPACKING crair E E O OER ENE 11 TROUBLESHOOTING GUIDE riesia I EOE N E AER REOT 12 SPECIFICATIONS SHEE Tanicsaninsiry rina R N A E 13 CONSUMER WARRANTY AND DEFECTIVE RETURN POLICY ssessessessesssessessesseeseeseessesseesesseesseosesseoseessessesses 14 Page 2 Introduction Congratulations on purchasing the XL 72 Theater by Sima Products Please read this instruction manual carefully before installing your inflatable screen When used properly according to this manual it will pro vide hours of entertainment for you and your family General Information and Warnings e Do not over inflate Us
4. d in air when a certain amount of pressure is applied FIG 4 Page 5 5 Attach the inflate end of the AC pump nozzle to one of the air valves on the frame by push ing the end firmly into the inflation port Be sure to close the unused valve so it doesn t leak air while inflating the screen FIG 5 NOTE THE PUMP ATTACHMENTS SHOULD NOT BE USED WITH THIS MODEL 6 Turn the pump to the on position On Switch is located on the face of the pump NOTE THE FRAME SHOULD NOT TAKE MORE THAN 5 MINUTES TO INFLATE MAKE SURE THE PUMP ISN T IN USE FOR MORE THEN 10 MINUTES IT CAN OVERHEAT WARNINGS e Never attempt to disassemble or close the openings while pump is operating e Never leave pump unattended while in use e Never allow sand small rocks etc to be sucked into the inflation or deflation port while operating e Do not use under wet conditions keep away from water e Never look into or point the inflate port toward your eyes while pump is operating e The power supply cord cannot be replaced If the cord is damaged contact Sima customer Service for a replacement pump e Keep away from children e When used outdoors or near water use a properly grounded GFI outlet FIG 5 Page 6 7 As the frame fills with air be sure it is clear of any nearby objects Guide the frame up as it fills with air helping to unfold and expand it It should take approximately 5 minutes for the screen to inflate
5. d of the possibility of such damages Sima s liability for damages in no event shall exceed the amount paid for this product Sima neither assumes nor authorizes anyone to assume for it any other liabilities Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state 2008 Sima Sima Products Corp 140 Pennsylvania Ave Bldg 5 Oakmont PA 15139 www simaproducts com PN 21781 Made In China Page 14
6. e only the supplied air pump as directed Never use an air compressor e This screen is not a flotation device do not use in any type of pool e To avoid danger of suffocation keep children away from the screen when inflating and deflating Do not let children sit or play on the screen Always deflate and store screen immediately after use Adult super vision is required e Do not use screen during high winds in excess of 15 mph or threat of lightning e Do not smoke near the screen Keep away from fire e Do not use sharp objects in any manner around the XL 72 Theater e Do not climb or sit on inflated surfaces e Clean only with mild soap and water Do not use harsh chemicals Sima Products has researched all regulations regarding the use of this XL 72 Theater We have not found any regulations related to the use of our screen however we will not be responsible if some other regula tions apply to this product in the country you intend to operate the system It is the users responsibility to be aware of such regulations and obey them Sima Products will not accept any responsibility for failure to meet local regulations Model XL 72 Size Inflated 69 x 32 x 70 with pontoons 69 x 32 x 54 5 without pontoons Weight approximate 28 Ibs Page 3 List of Materials Your package should include the following materials Inflatable Frame 72 White PVC Screen 16 Extra set of detachable pontoons 1 Air pump inflat
7. eft inflated overnight during a moderate temperature change the frame will show a loss of air pressure Be sure to deflate frame and store after usage Video is not bright enough on the screen Part of the picture is missing viewing in the rear projection position SOLUTION 1 Remove the screen prior to deflating and roll it back up for storage 2 Setup the screen and frame in a warm environment Sunlight to remove the wrinkles from the screen 1 Be sure to remove the air pump hose after inflating Air can leak back through the pump if not removed 2 Check the inner rubber air valves are seated properly prior to closing outer threaded cap 3 Listen for air holes in the frame around the seams You may use mild soap and water to locate the leak 1 Use a projector with enough lumens to better view your video for certain indoor outdoor conditions 1 Place the projector on a stand so its height is centered in the screen Page 12 Specifications sheet Inflatable Frame Descriptions e Inflates in under 5 minutes with pump e Velcro attachment areas Standard Screen Descriptions e 16 x9 HD Wide screen 4x3 format compatible e Compatible with all types of projectors e Front and rear projection capable e Hi Definition bright white vinyl material e Velcro patches for attaching to frame Other Accessories Included e 1 Air Inflator Deflator UL Listed with Hose 120v AC e 1 Set of additional heig
8. ht adjustment pontoons Technical Specifications e Frame Material 0 4mm PVC e Screen Material 15mm PVC e Product Dimensions 69 x 32 x 70 with pontoons 69 x 32 x 54 5 without pontoons e Shipping Weights 28 Ibs e Air pump 120v AC UL Listed Inflator Deflator Page 13 90 Day Limited Warranty Sima Products Corporation Sima Products Corp Sima warrants that if the accompanying product proves to be defective to the Original purchaser in material or workmanship within 90 days from the original retail purchase Sima will at Sima s option either repair or replace same without charge but no cash refund will be made What you must do to enforce Warranty You must deliver mail or ship the product together with both the original bill of sale and this limited Warranty statement as proof of warranty coverage to Sima Products Corp Attn Customer Service 140 Pennsylvania Ave Bldg 5 Oakmont PA 15139 Phone 412 828 3700 It is recommended that you call Sima at the number listed above to obtain a return authorization number Limitation of Liability and Remedies Sima shall have no liability for any damages due to lost profits loss of use or anticipated benefits or other incidental consequential special or punitive damages arising from the use of or the inability to use this product whether arising out of contract negligence tort or under any warranty even if Sima has been advise
9. ng It is recommended to remove the screen from the frame before packing to prevent damage and creases in the screen 1 When storing remove the screen prior to deflating the frame fold and roll it back onto the tube for storage FIG 9 2 To deflate the frame uncap one of the air valves from either base FIG 10 3 Press in on the inner check valve After 20 seconds the seal should lock into place This will allow you to squeeze most of the air out prior to hooking up the pump FIG 11 4 Squeeze the air out of the frame until it s deflated to ground level FIG 12 5 Attach the Deflate end of the AC pump to the air valve on either base 6 Turn the pump to the on position for the next few steps 7 Layout the frame as shown in figure 12 8 Fold each base in half Now begin to roll the frame from one base down to the next base FIG 13 9 Turn the pump off after screen is rolled up for storage 10 Unplug amp remove the pump from the frame Pack the pump up for storage NOTE THE PUMP CAN BE USED INTERMITTENTLY AS YOU DEFLATE AND PACK UP THE FRAME FEEL FREE TO USE IT WHEN NECESSARY TO DEFLATE ANY AIR AS NEEDED THROUGHOUT THE ENTIRE DEFLATION REPACKING PROCESS FIG 13 Page 11 Troubleshooting Guide PROBLEM Wrinkles amp Creases in the screen Note Some wrinkles are normal and will not affect the viewing image The Frame is deflating over time Note If the frame is l
10. or deflator Part 52472 Select A Setup Site e Select a site that has the necessary height clearance for the screen and enough room for your projector to properly focus and size the projected image The screen will stand nearly 63 inches in height Allow approximately 6 to 8 feet in front or behind for rear projection of the screen to adjust the projector e Be sure there are no sharp objects lying on the surface that might puncture or tear the screen e Check to be sure that a 110V 120V AC wall outlet is within reach to plug in the air pump Use a properly grounded GFI outlet if using the product outdoors e Unpack the screen at the location in which it will be inflated Page 4 Unpacking the Screen 1 Remove all the items from box Don t cut the boxes too deep as this may damage the screen FIG 1 Inflating the screen 1 Remove the frame from the package Unroll the screen as shown at right Be sure both bases are facing the correct way Both air valves should be facing the same direction FIG 2 2 Plug the AC air pump into an AC power outlet NOTE POWER SUPPLY MUST BE 120V AC 60 Hz USEA PROPERLY GROUNDED GFI OUTLET IF USING THE PRODUCT OUTDOORS 3 Locate the air inlet outlet valves You will notice that each valve on each base has two layers of seals that cut off the airflow The outer seal is a threaded cap that screws into place FIG 3 4 The inner seal is a rubber check valve designed to hol
Download Pdf Manuals
Related Search