Premier UNI-EPDS project mount
Contents
1. Mounting Hardware Too Long The depth of some projector mount points may prevent you from tightening the M2 5 and M3 mounting hardware You can reduce the length of the M2 5 and Mounting Hardware M3 mounting hardware by stacking up to a maximum of five 5 M3 flat washers inside the leveling barrel M3 Washer Avoid stacking too many M3 washers the mounting hardware must thread into the projector mount point at least four 4 complete turns Leveling Barrel Cutaway View Installation Instructions Visit the Premier Mounts website at http www mounts com Page 13 b a SZ UNI STA UNI EXT Attaching the Universal Projector Plate contd Raise or lower each of the mounting legs by rotating the leveling barrels until all of the mounting legs are at an equal height Lower the mounting leg by rotating the leveling barrel counter clockwise Raise the mounting legs by rotating the leveling barrel clockwise Identify the projector s approximate front to back center of gravity Place your hands on each side of the projector and gently lift it an inch from the surface on which it is resting Carefully adjust your grip on the pe projector until it seems balanced from front to back Front to Back Mentally note the apparent center of gravity DEn Center of Gra2. Tighten all screws A Do not overtighten the mounting screws Follow the PDS Installation Instructions to complete the installation Base Box Adjustment You can adjust the roll of the projector by loosening the three 3 front and rear M6 x 12mm screws Do not fully loosen the screws as the mount may drop Set the desired roll and then tighten the screws First tighten the center screws and work your way to the outside screws making any final adjustments prior to tightening the last two screws You can adjust the tilt of the projector by loosening the two 2 M6 x 12mm screws on each side of the Base Box Set the desired tilt and then tighten the screws making any final adjustments prior to tightening the last two screws If your projector is not holding the tilt install the four 4 external tooth washers on the four 4 M6 x 12mm Phillips head screws w Integrated Washers Once all adjustments have been made tighten all hardware Page 16 Visit the Premier Mounts website at http www mounts com Installation Instructions 4 UNI STA UNI EXT 24 Set Screw Installation fi The security set screw will prevent the unit from being removed and from being knocked Upper Mounting out of adjustment Bracket The M6 set screw will be used in conjunction with any standard threaded adapter sold separately M6 Set Screw Thread in threaded adapter until securely fastened Thread in one 1 M6 x 6mm set
3. above Raise the adjustable mounting bracket into position Align the mounting holes of the upper ti A mounting plate with the mounting holes of the inner slide plate Two 2 one per screw nylon washers must be placed between the adjustable mounting bracket and the projector arm see inset to the right Secure and finger tighten two 2 M6 x 16mm security head screws If using the optional extension arm proceed to Page 10 If needed determine the Throw Distance again Once the correct throw distance has been determined use the security wrench supplied to tighten the mounting screws If the adjustable mounting bracket needs to be adjusted the four 4 M6 x 12mm security screws may be loosened so that the bracket can be moved 2 Once the desired height has been achieved re tighten the hardware Do NOT overtighten these screws Proceed to the Attaching the Base Box to the Adjustable Mounting Bracket section Installation Instructions Visit the Premier Mounts website at http www mounts com Projector Arm Adjustment Slot Inner Slide Plate Upper Mounting Plate Adjustable Mounting Bracket Calculated Throw Distance Nylon Washer M6 x 16mm Security Screw Security Wrench Page 9 gt 4 22 Attaching the Base Box to the Adjustable Mounting Bracket ji The M6 x 12mm security head screws must be mounted from the underside
4. b a UNI STA UNI EXT 24 Determining the Installation Height In order to determine the installation height and throw distance the PDS PLUS projector bracket must be mounted to the projector Please refer to the PDS PLUS Installation Instructions prior to performing the following steps Refer to the projectors User s Manual to determine the offset of the projector lens to the top of the screen whiteboard B Projector Measure distance from center of lens to the top of the PDS PLUS bracket C Add the distance from the ground to the top of the screen A Add the projector manufacturers recommended offset from the projector manual B Add the measurement from Step 1 C and then add 2 5 to the total Example A B C 2 5 Add the measurements to determine the mounting height mark Place a mark at the top of the total calculated height measurement starting from the ground up This mark will represent the lower edge of the wall plate Top of Screen Legend Distance from ground to the top of the screen whiteboard viewable area Manufacturers recommended offset measurement This measurement will be listed in the Users Manual Center of the lens to the top of the projector bracket Add 2 5 to the calculated total This total distance will be the location for the bottom rail on the wall plate Proceed to the Wood Stud Installatio
5. gt D PREMIER C4 MOUNTS CREATING POSITIVE CUSTOMER EXPERIENCES INSTALLATION INSTRUCTIONS Universal Short Throw Projector Arm Model UNI STA UNI EXT NORTH AMERICA EUROPE 3130 East Miraloma Avenue Swallow House Anaheim CA 92806 USA Shilton Industrial Estate USA and Canada Shilton Coventry England CV79JY Phone 1 800 368 9700 Phone 44 0 2476 614700 Fax 1 800 832 4888 Other Locations Phone 001 714 632 7100 Fax 001 714 632 1044 Fax 44 0 2476 614710 9530 010 001 07 24 UNI STA UNI EXT A Table of Contents Weight Capacity aicsreregu te oiana e E E A E EEE E EATE FA E EER D O E E RASAR De Warning Statements i de Installation Tools 3 Parts List 3 PDS PLUS STA PDS PLUSW STA Mounting Hardware 4 Lock It Security Pack wn 4 Determining the Installation Height 5 Wood Stud Installation x6 Attaching the Projector Arm T Throw Distance Calculation nies 8 Adjustable Mounting Bracket Installation EEES O 9 Attaching the Base Box to the Adjustable Mounting Bracket 10 Extension Arm Installation Optional 10 Low Profile Bracket Installation 11 Attaching the Base Box to the Upper Mounting Plate 11 Attaching the Universal Projector Plate cscs LD Attaching the Projector 16 Base Box Adjustment 16 Set Screw Installation ee 17 Utilizing the Storage Feature 17 Cable Management 18 Technical Specifications 19 Warranty 20 Weight Capacity THE WALL STRUCTURE MUST BE CAPABLE OF HOLDING FIVE Maximum p
6. of the base box A Do NOT overtighten these screws Raise the base box to the upper mounting bracket Align the two 2 one each side mounting holes Using a security wrench insert and tighten two 2 M6 x 12mm security head screws Attach the projector to the base box referring to the PDS PLUS installation instructions for final adjustments Extension Arm Installation Optional ti A arm UNI STA UNI EXT Adjustable Mounting Bracket M6 x 12mm Screws Base Box Security Wrench Please see the Operator s Manual to determine the correct throw distance the distance from the projector to the screen The throw distance must be determined prior to mounting the projector Page 8 If the extension arm is purchased at a later date the end cover must be removed prior to installing the extension Slide the extension arm into the open end of the UNI STA the front of the mount Adjust length so that the center of the adjustable mounting bracket matches the throw distance calibration Line up the mounting holes on the extension arm with the mounting slots on the UNI STA Using a screwdriver insert and tighten two 2 M6 x 12mm security head screws and M6 flat washers through the external slide plate and tighten Attach the projector ti Please refer to Attaching the Base Box to the Adjustable Mounting Bracket above forsteps on attaching the projector Proceed to the Low Profile Bracket
7. screw M3 Security Use an M3 security wrench to tighten the Wrench M6 set screw included in the PDS PLUS hardware Proceed to the Utilizing the Storage Feature section Utilizing the Storage Feature The storage feature may be used to store electronic components There is an accessible door on each side of the storage enclosure It may be securely held shutwith the use of four 4 M5 x 8mm security head screws It may be easiest to pre wire all cables down the arm or extension at this time Open the storage door that is located on the side of the wall plate Place the electronic components inside the storage enclosure Make all electronic connections at this time Close the storage door and secure using two 2 1 upper and 1 lower M5 x 8mm security head screws Tighten using a security wrench Repeat this process for the other side as well Proceed to the Cable Management section Electronic Components M5 x 8mm Security Screw nstallation Instructions Visit the Premier Mounts website at http www mounts com Page 1 wb e UNI STA UNI EXT Cable Management The cable access holes are located at the end of the short throw mount and on the wall plate UNI STA Route the cables through one end of the UNI STA UNI EXT and out the other end Electronic Attach the end cover with an M5 x 8mm security Components head screw S Electronic Components Cables tn You may direct the cables out the e
8. Installation section Page 10 Visit the Premier Mounts website at http www mounts com Plate lt M6 Flat Washers M6 x 12 a Security Screw Security Wrench Extension Arm Optional Adjustable Mounting Bracket Installation Instructions UNI STA UNI EXT 24 Low Profile Bracket Installation tin Projector dimensions differ between manufacturers If the projector hangs too low from the UNI STA UNI EXT the adjustable mounting bracket may be removed This will allow you to attach the base box directly to the upper mounting bracket for an even lower profile installation Using a M5 security wrench remove the four 4 M6 x 12mm security screws by rotating the security wrench counterclock wise Slide the adjustable mounting bracket off the upper mounting bracket Proceed to the Attaching the Base Box to the Upper Mounting Plate section M6 x 12mm Screws Adjustable Mounting Bracket Upper Mounting Bracket M5 Security Wrench Attaching the Base Box to the Upper Mounting Plate The PDS PLUS comes with optional security hardware Lock It Security Pack that my be installed for added security Please review the installation instructions that came packaged with the projector before attaching the projector to the upper mounting bracket The M6 x 12mm security head screws must be mounted from the underside of the base box Do not overtighten the screws Raise the base box to the upper m
9. always make sure that there are no electrical wires in wall Cutting drilling into an electrical line may cause serious injury Make sure there are no water lines inside the wall where the mount is to be located Cutting drilling into a water line may cause severe water damage to the mounting surface This product is intended for indoor use only Use of this product outdoors could lead to product failure and personal injury Do not install near sources of high heat Do not install on a structure that is prone to vibration movement or chance of impact Contact Premier Mounts with any questions 800 368 9700 techsupport mounts com Page 2 Visit the Premier Mounts website at http www mounts com Installation Instructions UNI STA UNI EXT 24 Installation Tools The following tools may be required depending upon your particular installation They are not included Phillips Screwdriver Ya Drill Bit 2 Socket and Socket Wrench Parts List Make sure your Premier Mounts product has the following hardware and components before beginning installation If there are parts missing and or damaged stop the installation and call Premier Mounts at 800 368 9700 UNI STA UNI EXT Hardware Extension Hardware Pack Extension Arm Optional Qty 1 included with the UNI EXT M6 x 12mm Security Qty 2 y X M6 Flat Washer Internal Slide Plate Wall Plate Qty 1 Qty 1 End Cover Adjustable Mounting Assembly External Slide Plate Ba
10. ch of the mounting legs A Do not overtighten the mounting screws You can use either the standard Phillips head or Lock It security hardware Insert one 1 Barrel Cap into the end of each leveling barrel Proceed to the Single Mount Point Installation section Single Mount Point Installation A single 4 20 x 5 16 screw must be used to attach the Universal Projector Plate to the projector if your projector has only one mounting point A Do not overtighten the mounting screws You can use either the standard Phillips head or Lock It security hardware Proceed to the Attaching the Projector section nstallation Instructions gt 4 24 UNI STA UNI EXT Attaching the Projector Place one 1 nylon washer and one 1 1 4 flat washer over the hinge pin Insert and tighten one 1 M6 x 12mm screw Repeat 0 and for the opposite hinge pin fs You can use either the standard hardware or Lock W it security hardware Replace eight 8 M6 x 12mm screws and one 1 M6 x 8mm set screw A Do not overtighten the M6 x 12mm screws or the M6 x 8mm set screw Slide the projector Projector Plate assembly onto the PDS Base Box Hook the Projector Plate over the hinge pins as shown Insert the four 4 M6 x 12mm tilt adjustment screws two 2 per side You can use either the standard hardware or Lock It security hardware
11. ck Plate Covers Qty 1 Pre Assembled Qty 1 Qty 1 Qty 2 M5 x 8mm Security M6 x 16mm Security 4 M6 x 12mm Security Nylon Spacer Screws Qty 7 Screws Qty 2 Screws Qty 2 Qty 2 Projector Bracket Mounting Legs Long Mounting Legs Short Qty 1 Qty 4 Qty 4 Installation Instructions Visit the Premier Mounts website at http www mounts com Page 3 gt 4 24 UNI STA UNI EXT Parts List con d Base Box Qty 1 External Tooth Washer Qty 4 M6 x 12mm Phillips Head w Integrated Split Washer Qty 12 6 pre installed M2 5 x 10mm Phillips Pan Head Screw Qty 4 M6 x 8mm Set Screw Qty 1 M3 Flat Washer Qty 10 M2 5 x 12mm Screw Qty 4 M3 x 16mm Screw Qty 4 M4 x 12mm Screw Qty 4 M5 x 12mm Screw Qty 4 M6 x 12mm Screw Qty 8 1 4 20 x Y Screw Qty 1 PDS PLUS STA PDS PLUSW STA Mounting Hardware Nylon Spacer Qty 2 Flat Washer Qty 2 Security Wrenches Qty 2 M6 x 12mm Security Head w Integrated Split Washer Qty 12 M2 5 x 10mm Security Screw Qty 4 M6 x 8mm Security Set Screw Qty 1 M3 Flat Washer Qty 10 M2 5 x 12mm Security Screw Qty 4 M3 x 16mm Security Screw Qty 4 M4 x 12mm Security Screw Qty 4 M5 x 12mm Security Screw Qty 4 M6 x 12mm Security Screw Qty 8 20x Yg Security Screw Qty 1 Page 4 Visit the Premier Mounts website at http www mounts com Installation Instructions
12. efer to the projectors Users Manual to Calculations determine the distance from the lens to X Manufacturers recommended the front of the screen X throw distance Measure the distance from the front of the lens to the center of the projector Y Z Distance from wall to face of whiteboard screen Front Lens Measure the distance from the wall to the face of the whiteboard screen Z Front Lens Throw Distance X Y Z Add all measurements X Y Z to determine projector placement on the bbe Lens Throw Distanae arm assembly This measurement X Y Z will determine where the center of the mount bracket will be located on the arm assembly Please make note of this measurement The UNI STA UNI EXT can be also used as a wall mounted standard projector mount as Rear Lens well as a short throw projector mount Align the projector facing the opposite direction from the wall plate to project the image across the room Please take into account the projectors throw capabilities prior to mounting in the projector opposite direction Proceed to the Adjustable Mounting Bracket Installation section Page 8 Visit the Premier Mounts website at http www mounts com Installation Instructions UNI STA UNI EXT Adjustable Mounting Bracket Installation 1 Insert the inner slide plate into the projector arm Determine which adjustment slot best matches your throw distance calculation
13. he correct screws should thread easily into the mounting point and not pull out when tension is applied Does your projector have multiple mount points or a single mount point Depth Plus 1 8 Allowance Small Straw Mark or Toothpick or Toothpick If your projector has multiple mount points proceed to the Multiple Mount Point Installation section If your projector has a single mount point skip to the Single Mount Point Installation section Page 12 Visit the Premier Mounts website at http www mounts com Installation Instructions UNI STA UNI EXT 24 Attaching the Universal Projector Plate contd Multiple Mount Point Installation Locate the projector s mount points Position an appropriate number of mounting legs on the projector You can use any combination of three 3 or more long mounting legs and short mounting legs depending on the number and location of the thread inserts on your projector The number and placement of mount points W on projectors varies between projector manufacturers This example projector has five 5 mount points but only uses four 4 mounting legs Insert the mounting hardware as determined in the Selecting the Mounting Hardware section through the leveling barrel into the thread insert of the projector You can use either the standard Phillips head or d Lock It security hardware Do not tighten the mounting hardware at this time
14. n section Installation Instructions Visit the Premier Mounts website at http www mounts com Page 5 wb e UNI STA UNI EXT Wood Stud Installation Do NOT over tighten lag bolts when attaching the mount to the wall Improper installation may result in personal injury or damage to property THE EXACT CENTER OF THE STUD MUST BE LOCATED FOR CORRECT AND SAFE INSTALLATION Use an electronic stud finder not supplied to locate the center of the stud that is in the wall lt Wood Stud Stud finder I Mounting Point Je Mark I de Height Mark from page 5 Use a pencil to mark the first mounting point just above your height mark from page 5 Use the level to make sure the wall plate is level from side to side Place the wall plate over the first mounting point mark and use a pencil to mark the rest of the mounting points tin Four 4 mounting points must be used Two 2 upper mounting points and two 2 lower mounting points Marking Once the mounting points have been marked use a 4 drill bit and portable drill to drill the pilot holes Page 6 Visit the Premier Mounts website at http www mounts com Installation Instructions UNI STA UNI EXT 24 After the pilot holes have been drilled use four 4 X 3 lag bolts and four 4 square washers to mount the wall plate to the wooden studs Use a socket and socket wrench to finish this step Socket Insert and gently tap the up
15. nd of the UNI STA UNI EXT The end cover has a perforated tab to allowcables to pass out the end Pliers must be used to bend the perforated tab If the cables will not fit the end cover may be removed by loosening and extracting the M5 x 8mm security screw Cable Opening x x age Projector Hook Ups UNI EXT Cable Opening Electronic Components Projector Connections UNI STA UNI EXT M5 x 8 Security Screw End Cover Extension Bracket Perforated Tab nstallation Instructions UNI STA UNI EXT Technical Specifications All measurements are in inches mm 3 53 90 OPTIONAL EXTENSION St 67 00 1702 MAX DIST 27 40 696 2 00 3 75 50 80 95 25 24 00 610 m 406 aa sss ss 585 3535 3555 10 69 272 9 60 244 Q 3 00 76 26 04 661 MIN DIST 114 30 4 00 T 101 60 nstallation Instructions Visit the Premier Mounts website at http www mounts com Page 19 wb e UNI STA UNI EXT Warranty PREMIER MOUNTS LIMITED LIFETIME WARRANTY What and Who is Covered by this Limited Warranty and for How Long Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of this product The limited warranty is valid only for the original purchaser of the product What Premier Mounts Will Do A
16. ounting bracket Align the two 2 one each side mounting holes Using a security wrench insert and tighten two 2 M6 x 12mm security head screws Attach the projector to the base box referring to the PDS PLUS installation instructions for final adjustments diy diy diy Ay a Proceed to the Attaching the Universal Projector Plate section Base Box M6 x 12mm Screws Security Wrench Installation Instructions Visit the Premier Mounts website at http www mounts com Page 11 b a CA UNI STA UNI EXT Attaching the Universal Projector Plate Selecting the Mounting Hardware Insert a small straw or toothpick into the threaded inserts found on the bottom or top of the projector Use a pencil to mark the depth of the threaded insert on the small straw or toothpick Mark the straw or toothpick 1 8 above the depth of the threaded insert as shown in Figure 1 Insert the small straw or toothpick into the remaining threaded inserts to compare and verify their depth using the straw or toothpick s 1 8 allowance mark Locate the correct diameter screw for the threaded insert Marking the 1 8 If the screw you selected is longer than the 1 8 ites allowance mark on the small straw or toothpick Marking the Depth as shown in Figure 2 and Figure 3 do not use this screw The screw length must not bypass the mark Threaded Insert Test each size of the screws provided Small Straw or Toothpick T
17. per and lower back plate covers into place Back Plate Covers Proceed to the Attaching the Projector Arm section Attaching the Projector Arm Locate the mounting hook cutout on the top of the wall plate Tilt the arm slightly and gently insert the mounting hooks into the mounting hook cutouts Slowly lower and let the projector arm rest against the wall plate ftp If using the storage feature of the product it may be easier to route any wiring at this time please see Page 12 A MAKE SURE THE PROJECTOR ARM IS FULLY Mounting Hook Cutout SEATED BEFORE RELEASING THE UNIT r Mounting Hooks Wall Plate Projector Arm Installation Instructions Visit the Premier Mounts website at http www mounts com Page 7 24 UNI STA UNI EXT Locate the two 2 lock mounting points on the projector arm These two points will be aligned with the lock mounting points on the wall plate Using a security wrench insert and tighten two 2 M5 x 8mm security head screws Look Mounting Point A Do NOT overtighten these screws Proceed to the Throw Distance Calculation section M5 x 8mm Security Head Screw Security Wrench Throw Distance Calculation hi Please review the Operator s Manual that came packaged with your projector before attaching the upper mounting bracket The correct throw distance the distance from the projector to the screen must be determined prior to mounting the projector R
18. rojector weight 50 lb 7 5 TIMES THE WEIGHT OF THE PROJECTOR IF NOT THEN THE WALL STRUCTURE MUST BE REINFORCED Warning Statements aa PRIOR TO THE INSTALLATION OF THIS PRODUCT THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UN DERSTOOD THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE STOP PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR MODIFICATIONS AND IS NOT RESPONSIBLE FOR ANY DAMAGES CLAIMS DEMANDS SUITS ACTIONS OR CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE ATTACHMENTS OR MODIFICATIONS STOP SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT USE PROPER TT AT PPS OOE SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY At least two qualified people should perform the assembly procedure Injury and or damage can result from dropping or mishandling the projector If mounting to studs make sure that the mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is recommended Be aware of the mounting environment If drilling and or cutting into the mounting surface
19. ss and telephone number General inquiries can be addressed to Premier Mounts Customer Service at 1 800 368 9700 Warranty claims will not be accepted over the phone or by fax Premier Mounts Attn Warranty Claim 3130 East Miraloma Ave Anaheim CA 92806 How State Law Applies THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE DIXA CULA Premier Mounts intends to make this manual accurate and complete However Premier Mounts makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Premier Mounts makes no representation of warranty expressed or implied regarding the information contained herein Premier Mounts assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Page 20 Visit the Premier Mounts website at http Awww mounts com nstallation Instructions
20. t the sole option of Premier Mounts Premier Mounts will repair or replace any product or product part that is defective If Premier Mounts chooses to replace a defective product or part a replacement product or part will be shipped to you at no charge but you must pay any labor costs What is Not Covered Limitations PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS ADAPTERS DISPLAYS PROJEC TORS OTHER PROPERTY OR PERSONAL INJURY RESULTING IN WHOLE OR IN PART FROM IMPROPER INSTALLATION MODIFICATION USE OR MISUSE OF ITS PRODUCTS PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE PREMIER MOUNTS IS NOT RESPON SIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAM AGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU What Customers Must Do for Limited Warranty Service If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address below within thirty 30 days Proof of purchase an original sales receipt from the original consumer purchaser must accompany all warranty claims Warranty claims must also include a description of the problem the purchaser s name addre
21. vity Identify the projector s approximate side to side center of gravity Place your hands on the front and back of the projector and gently lift it an inch from the surface on which it is resting Carefully adjust your grip on the projector until it seems balanced from side to side Mentally note the apparent center of gravity Place the Universal Projector Plate on top of the mounting legs with the center hole as close as possible to the projector s center of gravity 5ide to Side Center of Gravity Verify that the mounting legs are at an equal height a Return to Ea if they are not at an equal height or Sliding M6 the Universal Projector Plate is not level Square Nut Verify the position of the integrated sliding M6 square nut in the mounting leg relative to a nearby slot on the Universal Projector Plate If the M6 square nut is not aligned with any slot you O can use any thin implement such as a toothpick to nudge it into alignment Page 14 Visit the Premier Mounts website at http www mounts com nstallation Instructions b 4 UNI STA UNI EXT 24 Attaching the Universal Projector Plate contd Tighten the mounting screws to the projector A Do not overtighten the mounting screws Attach the Universal Projector Plate to each of the mounting legs by inserting and tightening one 1 M6 x 12mm screw through the Universal Projector Plate into the M6 square nut on ea
Download Pdf Manuals
Related Search