Draper Silhouette/Series V
Contents
1. Slide Switch Back View surface to the desired position and press the STOP button Press and hold the STOP button for at least three seconds to record the position Please Note Pressing and releasing the UP button on the switch will move the screen to its upper limit Pressing and releasing the DOWN button will move the screen to its lower limit While the motor is in motion pressing the STOP button for less than two seconds will stop the viewing surface at its present position Once the motor is stopped pressing the STOP button will move the view ing surface to its alternate format position Pressing and holding the STOP button when the motor is at rest or in mo tion for at least three seconds will record a new alternate format position Tab Tension Adjustment Procedure for Silhouette Series V Determine which side requires adjustment Secure dowel with one hand Caution Do not touch or bend surface Using Philips head screwdriver depress spring loaded adjustment screw see drawing and slowly turn clockwise to tighten tension or counter clockwise to loosen tension The screw adjusts in turn increments Adjust only one increment 14 turn If problem is not corrected leave screen in position for 24 hours to allow surface material to stretch into position If problem still is not corrected repeat steps and Dowel ane Adjustment Screw i Tensioni2. Switch and Power Supply into splitter then run cable from Splitter to MC1 Eye Port To AC Line Wiring Diagram for Optional Built in Video Interface Control Built in Video Interface Control Junction box at left end of screen N internal screen wiring N gt Blue Neutral 220 VAC supply G Black Hot Green Yellow Ground Trigger signal VIC220 220 VAC white cord amp plug VIC12 12 VDC brown amp orange leads pot Dashed wiring by electrician www draperinc com RARER 765 987 7999
3. www draperinc com RARER 765 987 7999 220V Silhouette Series E amp V by Draper Page 5 of 5 ILT Switch to Motor Dry Contacts or Data Cable connection Please Note This Splitter Jack is located inside the junc tion box of your screen Back of wall switch Motor Data Cable plugged in here Please Note Although both Dry Contact and Data Cable connections are shown you should only use one connec tion type per motor Data Cables to switches or to additional motors can be plugged into any of the three open jacks If this is a Case First Screen Later installation plug the motor cable into the jack indicated in the drawing a MC a Ta p Av fom pwn External Low Voltage amp Wireless Control Internal Screen Wiring White or Blue Common to screen amp 110 220V AC Neutral White Blue Common Red to screen directional r Red 110 Black 220 Up Brown to screen directional 4 Black 110 Brown 220 Down Yellow to 110 220V AC Hot T E oak J SL GreenYellow Black to 110 220V AC Hot 5 iat lt 4 Motor Ground Green Yellow Ground A Olos iu sat S Dashed wiring by electrician gt ETETETT Low voltage wiring by others te owe a To Eye Port for IR Eye RF Receiver or LED ka 110 220V Wall Switch For more t
4. only the hardware which comes with the screen or is specified in these instructions The screen or extension brackets should be mounted into studs or blocking in the wall ceiling or in drywall minimum thickness 13 mm 2 with speci fied anchors For any other type of installation follow all local building and safety codes Steel studs concrete or cinder block walls and all other types of non wood frame construction require the use of special screws or anchors The selection of appropriate mounting hardware should be made by a qualified professional installer When locating viewing surface and checking clearance for screen s operation remember surface is centered in case Take care to install wall ceiling electrical box and conduit so they will be fully concealed by the screen case after installation Handle case carefully to avoid scratching Regardless of mounting method screen should be positively and securely supported so that vibration or even abusive pulling on the viewing surface will not cause case to work loose or fall Installer must insure that fasteners used are of adequate strength and suitable for the mounting surface chosen Wall Mounting Mount two three or four aluminum brackets provided Z Clips on the wall at desired height using appropriate fasteners Verify that they are in line and level to fully engage with the mounting lip on back of screen case 42 mm of free space is required above the Z Clips to
5. Installation Operating Instructions 220V Silhouette Series E amp V Electric Projection Screen by Draper Caution Read instructions through completely before proceeding keep them for future reference Follow instructions carefully Installation contrary to instructions invalidates warranty Care in mounting and correct operation will mean long and satisfactory service from your Draper screen Screen should be accessible for complete removal should fabric become damaged or should other service be required Screen should be installed level using a carpenter s level Nothing should be fastened to screen dowel or viewing surface Operating switch es packed separately in screen carton Do not discard with packing material Screen operates on 220V AC 50 hz 1 ph current NOTE Screen has been thoroughly inspected and tested at factory and found to be operating properly prior to shipment These instructions are meant as a guide only They do not imply any responsibility on the part of Draper Inc for improper installation or faulty workmanship at the jobsite Installation Your Draper screen can be mounted on a wall or suspended from the ceiling or mounted on 15 cm or 25 36 cm extension brackets Extension brackets must be ordered separately from Draper With each method of installation the case must be mounted level and with the flat back parallel to the wall To reduce the risk of personal injury use
6. Lh gee Black 220v Up r 4 4 4 4 H 3 Green Yellow Motor Ground a ae a a Black 220v Up peqeqed p5 3 sks r J 3 Green Yellow Motor Ground Pal E i 3 Green Motor Ground TEE i a poe Pie com EEN ae Poe as vow boro a ee TEE Mad ot PER li Data Cable i bate pA C rate gh 4 Cap off with wire bop ae 4 bob f i i 4 l Ly nut amp tape y i l poi i ey od oa eee Beane b de pa E eli a eee P i Red _ Blue Mani i pe ee es lappa a 220v 50 Hz ee al i l Black 220v Control pi boci Red H Blue 50 Hz switch l i i i i l I t v i ae I Dashed wiring Wall Switch B I Black a Dashed wiring x i Red H Blue py insteller te Wall Switches U fal by installer a aje receiver RF or IR a i 7 or integrated Receivers 220v i Black control system or integrated 50 Hz E Dashed wiring control systems 3 ji by installer z l 220v 50 Hz Wiring Diagrams Plug amp Play 220V Motor with Built in Low Voltage Controller Single Low Voltage Control Multiple Low Voltage Controls Internal Screen Wiring Internal Screen Wiring o White Neutral o White Neutral I o Black o Black gt Green Ground gt Green Ground Data Cable Data Cables Wall Switch RF or IR Receiver Wall Switches or integrated RF or IR control system Receivers or integrated 220V PRIN control systems
7. allow case lip to be engaged over the lip of the Z Clips Engage the lip on back of screen case with lip of Z Clip and gently pull down to fully engage case to brackets i pio e i 411 S Pearl St Spiceland IN 47385 USA I 1 765 987 79 www draperinc com I fax 1 765 987 1689 Copyright 2011 Draper Inc Form SilhouetteE amp V220V_Inst 11 R Printed in U S A US Patent Nos 5 296 964 6 111 694 Lip on back of case C Silhouette fully engaged on Z Clip Z Clip wall mounting bracket supplied with Silhouette Ceiling Suspended Mounting Locate two offset ceiling brackets supplied and slide these into the chan nel on top of screen case by aligning the chamfered edges of each bracket parallel to the channel length Allow bracket to drop against bottom of channel and then rotate bracket counter clockwise Slide one bracket to each end of screen case until it stops against end cap of case Tighten two set screws to lock bracket in place Make sure that the flange of the ceiling bracket that has four holes is extended beyond the end caps of the case Repeat above procedure for second ceiling bracket making sure to slide it towards opposite end of case Ceiling bracket in channel of case To mount against ceiling hold screen case against ceiling and mark mount ing hole locations Each bracket has two holes towards the front edge and two holes towards the back edge Installer must
8. ase Note Be sure the clips are completely up against the ends of the fascia Page 2 of 5 Electrical Connections Screen operates on 220 V AC 50 Hz 1 ph current Junction box is located at left end of screen It is accessible through front of screen case after fascia is removed See instructions above for removing fascia Electrical supply wires can enter through the back or top of case For top entry remove plug from top conduit hole and snap plug into hole on back side of case Junction box contains brown black and blue pigtail leads and green internal ground wire per wiring diagram attached If optional low voltage control or video interface control is specified and factory installed please refer to wiring diagram on page three Wall or ceiling electrical box should be installed so as to be fully concealed by screen case after installation Screen is shipped with internal wiring complete and control switch es fully boxed Wire to connect screen to switch es and switch es to power supply should be furnished by installer Connections should be made in accordance with attached wiring diagram and wiring should comply with national and local electrical codes All operating switches should be off before power is connected Operation Before operating screen remove any shipping brackets or tape securing fabric and dowel to the roller If viewing surface is hanging out of the case 20 to 23 cm tape has probably been broken by r
9. ation VIC OS not available with factory installed VIC220 amp VIC12 KEY OPERATED SWITCHING Not CE Approved Two kinds of key operat ed switches are optionally available with this unit The key operated power supply switch controls power to the screen and switches When it is off the switches will not operate screen Key may be removed from the switch in either on or off position A three position key switch permits the screen to be operated directly by key In this case the screen s operator must always have a key RS232 ETHERNET Serial communication and network communication optionally available with wall switches RF or IR remote www draperinc com DRAPER 765 987 7999 220V Silhouette Series E amp V by Draper Adjustments Please Note Screen limits are factory set for optimum performance of the screen Any adjustment of these limits could void the warranty Please check with Draper prior to resetting screen limits A CAUTION Always be prepared to shut screen off manually when new adjustment is being tested Screen may be severely damaged if viewing surface is allowed to run too far up or too far down A CAUTION Be sure all switches are in off position before adjusting limit switches Adjusting fully up position Up stopping position may be adjusted by turning the yellow limit switch adjustment socket The yellow socket is located on left end of screen roller Turning the socket co
10. han one of A a amp _ Line these a splitter is required ba Pea L J 3 Button Wall Switch Location of key operated on off DOWN Black switch if furnished COM White ee UP Red ai a eee i im Control Aux Port for connecting additional LVC III Switches modules up to six total can be linked 24v DC connect from Aux to Eye Two Way Serial Communication RS232 with MC1 Internal Screen Wiring White or Blue Common White Blue Common Red to Screen directional 7 7 4 Red 110 Black 220 Up Black to Screen directional Black 110 Brown 220 Down Green 110V Program LED F Brown Hot to AC F Green Yellow Ground q i Ni HI Groen vellow 220V i gt Motor Ground Aai eiea an Low Voltage Wiring by others _ _ Fuse as AC Wiring by electricvan ie RS232 Data FROM Control System RS232 Data TO Control System Signal Ground amp Manual Switch Common Manual Switch Down See separate Serial Communica Tt Manual Switch Up epee tion RS232 Instruction sheet for ol Location of key p i Eye Port for IR Eye For RF Receiver or LED 1 Operated on off enabling RS232 with the MC1 Mea M wall Switch a Splitter and a Power Supply Loa switch if furnished is required Plug RF Receiver or LED Wall ee
11. nd vertically plumb Installer must insure fasteners not included are of adequate strength and suitable for chosen mounting surface Attach hanging bracket to wall bracket as shown Attach 1 Z Clip supplied with screen to hanging bracket as shown Engage the lip on back of screen case with lip of Z Clip and gently pull down to fully engage case to brackets Screw in 10 16 x 12 screw on each bracket to lock screen case in place see below CB 14 20 x 1 Z Keg 10 24 x Yo Flat Washer 20 Nylock Nut Hanging Bracket gt 10 24 x 12 Screw Nylock Nut Z Clip Removing Case Fascia Caution When removing or reattaching fascia do not handle fascia by unpainted ends Case fascia is removable to access roller assembly To remove fascia depress outward the spring lip located inside lower front corner of screen case and pull lower corner of fascia outward Repeat this at right end of case Support fascia from center and rotate lower front edge upward approximately 40 to disengage the Roll Lok hinge at the top front of screen case Fascia can now be completely removed from case To install fascia generally reverse instructions above making sure the Roll Lok hinge is completely engaged before rotating fascia down towards the closed position Depress spring clips outward push lower corners of fascia inward until lips of spring clips hook behind fascia Ple
12. ng Cable www draperinc com RARER 765 987 7999 220V Silhouette Series E amp V by Draper Page 4 of 5 Case Dimensions 22 mm holes for supply wires located on back and top 64 mm from left end of case Silhouette D Series E 13 5 cm Series V Varies m Series E Viewing Surface Shown Series V with Tab Tensioning also available At left Series V slat bar is depicted inside case Series E has a typical round bottom dowel For all Silhouettes the dowel is concealed inside the case Viewing Surface Wiring Diagrams Please Note Do not wire motors in parallel Wiring Diagrams 220V Motor and Quiet Motor Wiring Diagrams 220V Motor and Quiet Motor with Built in Low Voltage Controller Single Station Control Multiple Station Control Single Station Control Multiple Station Control Junction box at junction pox at CE Approved ieft end of screen Not CE Approved Junction box at CE Approved iat Shaor scree Not CE Approved eft end of screen g Internal Screen Wiring left end of s Internal Screen Wiring Internal Screen Wiring po 4 o Blue 220v Common Internal Screen Wiring Races ly gt Blue 220v Common ro 77 gt 7 4 Blue 220v Common L lo Brown 220v Down nA ts gt Blue 220v Common S ee gt Brown 220v Down r j Brown 220v Down i 1 2 1 Black 220v Up j gt Brown 220v Down 1 p d gt Black 220v Up
13. ough handling in shipment allowing surface to unwrap one turn off the roller Manually wrap fabric back around the roller without turning the roller itself When screen is first operated be cautious Cycle unit down and up several times to confirm satisfactory operation 220V SINGLE STATION CONTROL 3 position UP OFF DOWN switch permits operation to be stopped at any point Factory adjusted limit switches automatically stop screen when fully down or fully up 220V MULTIPLE STATION CONTROL Not CE Approved Switches are similar in appearance to 220V Single Station Control Screen stops when switch is released and may be restarted in either direction Factory adjusted limit switches stop screen automatically when fully up or fully down 24V MULTIPLE STATION CONTROL Three button UP STOP DOWN switches stop at any point desired operate in any sequence Factory adjusted limit switches automatically stop screen when fully up or fully down Installer should incorporate an all pole disconnect in the fixed wiring 220V amp 12V VIDEO INTERFACE CONTROL Not CE Approved Allows screen to be controlled by a trigger signal when the signal comes on the screen descends automatically Two versions Model VIC220 integrates screen operation with a Draper video projector lift or a video projector or tuner with a 220V switch outlet Model VIC12 interfaces with a 12V switch outlet Both available with an override switch VIC OS permitting independent oper
14. the wall switch Return the slide switch to the center position to return to normal operation To set the viewing surface to an alternate format position move the viewing Caution Do not remove the roller assembly from the case unless necessary for repairs If the roller assembly is removed be sure motor is fully re seated in the bracket and re secure it carefully with the motor retaining spring see diagram at right Page 3 of 5 viewing surface to retract farther into the case Turning it clockwise will cause the surface to stop farther out of the case One full revolution of the socket will alter the stopping position of the viewing surface by approximately 25 mm 1 Adjusting fully down position Down stopping position may be ad justed by turning the white limit switch adjustment socket The white socket is located on the left end of screen roller Turning the socket counterclockwise will allow the viewing surface to run farther down Turning it clockwise will shorten the viewing surface causing it to stop in a less extended position AT NO TIME SHOULD VIEWING SURFACE BE UNROLLED ENOUGH TO EXPOSE ANY PART OF SCREEN ROLLER I m To Motor oo O lool lwin UD Cc 7 Built In 5 p A l 7 BG Low Voltage n p m LA A POSITION FUNCTION Set LOWER limit qote DOWN imi UP Set UPPER limit CENTER Normal Operation no Oe Low Voltage
15. unterclockwise will allow the Limit Adjustments Built in Low Voltage Motors Please Note Screen limits are factory set for optimum performance of the screen Any adjustment of these limits could void the warranty Please check with Draper prior to resetting screen limits A CAUTION Always be prepared to shut screen off manually when new adjustment is being tested Screen may be severely damaged if viewing surface is allowed to run too far up or too far down A CAUTION Be sure all switches are in off position before adjusting limit switches Connect the ILT switch to the motor via the terminal blocks or via the modular port using four conductor modular cable When using modular cable the cable connectors MUST NOT be crimped in reverse as with standard telephone cable Set the slide switch to the lower position Press and hold the DOWN button on the switch to move the viewing surface to the desired lower limit If the screen moves in the opposite direction release the DOWN button and press and hold down the STOP button for four seconds This will reverse the operation of the UP and DOWN switches Move slider switch into center position Wait a couple of seconds Please Note If you move the slider switch from down to up in one mo tion it sets the two limits in the same postion Set the slide switch to the higher position Move the viewing surface to the desired upper limit by pressing and holding the UP button on
16. use at least two fasteners per bracket with one fastener in one of the two holes closest to back edge of bracket and one fastener in one of the two hole closest to front edge of bracket Installer must insure that fasteners are of adequate strength and suit able for the mounting surface chosen AAN eoa Ceiling bracket Mounting fasteners supplied by others 2 per bracket right end of Silhouette case front of Silhouette case If you encounter any difficulties installing or servicing your Silhouette screen call your dealer or Draper Inc Spiceland Indiana U S A telephone 765 987 7999 or fax 765 987 1689 220V Silhouette Series E amp V by Draper To mount suspended from ceiling the brackets need to be installed on screen case as noted on page one Attach S Hooks supplied through the holes in the brackets Select the set of holes that allows the screen to hang in a vertical position The installer is to provide the materials and fasteners to attach the S Hooks to the ceiling Installer must insure that the fasteners and suspension material is of adequate strength and suitable for the mounting surface chosen Mounting on 15 cm extension wall brackets 15 cm or 25 36 cm brackets are needed to mount Silhouette extended from wall Brackets are not supplied with screen and must be ordered separately Specify Silhouette Extension Brackets Mount the brackets to the wall making sure they are level a
Download Pdf Manuals
Related Search