Tecnoware ECO 0.90
Contents
1. Net Weight 2 5 Kg 2 6 Kg 3 5 Kg 3 6 Kg AKg Technical data may change without prior notice UPS ECO 0 50 0 70 0 90 1 1 1 3 9 User s manual 8 Maintenance 8 1 UPS Cleaning Before starting any cleaning operation be sure that 1 The AC Input Voltage for the UPS has been removed 2 The UPS is OFF Use only a cloth dampened with water to clean the unit If UPS works in an environmental unusually dusty or dirty remove the dirty from the ventilation holes Before restarting the UPS be sure it is completely dry If any liquid gets inside the UPS do not start the unit and contact Technical Service immediately 8 2 Battery If the UPS is NOT going to be used for a long period of time ensure that the batteries are left fully charged If the UPS has not been used for more than three months go through the First Start Up procedure described in the chapter 5 before using it again Please keep in mind that the batteries must be recharged at least once a month Take in mind that batteries are recharged automatically if the UPS works in Normal mode or if the UPS is off and connected to the AC Input Line Battery life strongly depends on the ambient temperature There are also other factors like the number of charge discharge cycles the discharge depth humidity and altitude The recommended environmental specifications for a correct use of batteries are listed in the Technical Specifications section 8 3 B2. dangerous even after the UPS has been disconnected from AC power mains Before any repair or maintenance work disconnect the batteries by removing the positive cable red colour from the positive pole of the battery It is compulsory to ground the UPS according to Safety Standards The AC mains power supply socket used to power the UPS must have an earth connection In the event of AC main power supply failure when the UPS works in Battery mode do not unplug the power supply cable to the UPS to ensure earth continuity to the connected loads Since the AC mains power supply cable acts as a separation device the AC mains power socket used to supply the UPS and or the rear side of the UPS must be accessible to easily disconnect the cable in case of dangerous conditions Risk of electric shock at the Output lines when the UPS is ON Risk of electric shock at the Output lines while the unit is connected to the AC utility line Do not obstruct ventilation slots or holes and do not rest any object on top of the UPS Do not insert objects or pour liquids in the ventilation holes Install the UPS indoors in a protected clean and moisture free environment Do not expose to the direct sun light Do not keep liquids flammable gases or corrosive substances near the UPS A User s manual 2 UPS ECO 0 50 0 70 0 90 1 1 1 3 1 Introduction ECO is an UPS Uninterruptible Power Supply specifically designed to protect your computer f
3. gt e TECNOWARE power systems Uninterruptible Power Supply ECO 0 50 ECO 0 70 ECO 0 90 ECO 1 1 ECO 1 3 User s manual Index aE AAAA MNOS u 2 E E T 2 T IHtEOJUCH One ee ee A AEA AE AAS 3 2 General Characteristies uan ern aaa 3 3 Receipt and s teselection n asien 4 4 EXTERNAL DESCRIPTION nun a 5 AT FROME Panel susanne ub aud EENEN EEEE KENEN 5 42 SRearSIdere re e ran N 6 Electrical Installation and First Start Up cc cece cece cece cc ccecccceccceeccces 6 6 PURCIONING nn es 7 6 1 N rmal MOdC wvevuies rk wns ao abe wine ene ene mh ae ns mh me mee ek nen 7 6 2 BILO Modes ee ses 8 6 3 Low Battery and Automatic Restart ccc cee cc e cece cee ceeeeeeceeceeceeees 8 GA Load CONTO creia a a aa nee 8 625 Fault Conditions 8 7 Technical Characteristics 4 Er Eee 9 Maintenance wasser 10 8 1 UPS ClOANINS ee re esse 10 0 2 BATY ZRRTRBRRRERTEREREERTERRERERTEURERERTERRERTTNTEERERTERRUTERTERRTFERTERRUFERTERN 10 8 3 Battery Replacement asien a 10 8 4 OPCVALON Sale Vest et eines 11 9 Troubleshooting 2 323283 Beer 12 Conformity to the European Directives cccceccccccccccscccescccescccsscccesccs 13 Product Disposalu as2 e essen 13 OAC Baul OOS re ee 13 Copyright 2011 TECNOWARE s r l All rights reserved All trademarks are property of their respective owners TECNOWARE s r l Via Montetrini 2E Molino del Piano Florence Italy www tecnoware com Editio
4. sure that all the devices connected to the UPS outputs are working correctly 7 Simulate a black out by removing the AC Input line The UPS starts working in Battery mode the UPS emits an acoustic alarm signal every 4 seconds and simultaneously the LINE BATTERY led flashes 8 Be sure that all the devices connected to the UPS outputs are working correctly and the UPS doesn t signal any sort of anomaly 9 Restore the AC Input line after few seconds the UPS turns back in Normal mode Before using ECO normally leave it in Normal mode in order to charge the batteries completely as specified at point 3 The batteries reach the 90 of their capacity after about 4 hours of recharge It is compulsory to ground earth the UPS according to the Safety Standards Risk of electric shock at the Output lines if the UPS is ON even when the UPS is not connected to AC utility line Risk of electric shock at the Output lines while the unit is connected to the AC utility line Risk of electric shock do not remove the cover The UPS contains internal parts which are at a high Voltage and are potentially dangerous capable of causing injury or death by electric shock There are no internal parts in the UPS that are user serviceable Any repair or maintenance work must be performed exclusively by qualified technical personnel authorized by TECNOWARE TECNOWARE declines any responsibility if this warning is disregarded Disregard for these warnings m
5. the UPS discharges a minimal amount of heat So it is necessary to leave at least 20 cm of unobstructed space all around the UPS in order to keep it properly ventilated Do not obstruct ventilation holes Do not insert objects or pour liquids in the ventilation holes Do not rest any object on top of the UPS Do not keep liquids flammable gases or corrosive substances near the unit Install the UPS on a properly tiled floor Avoid the installation on a floor that is not tiled flat User s manual 4 UPS ECO 0 50 0 70 0 90 1 1 1 3 4 EXTERNAL DESCRIPTION 4 1 Front Panel The front panel informs the user about operating status alarm conditions through 2 leds On the front panel there are see figure 1 1 The ON OFF button enables the user to turn ON OFF the UPS 2 The LINE BATTERY led this led blue color is always on during the functioning in Normal Mode it flashes one time every 4 seconds in Battery mode and it flashes one time every second in Low Battery condition 3 The ALARM led this led red color is on to indicate Alarm Fault condition mn TECNOWARE O Figure 1 Front panel UPS ECO 0 50 0 70 0 90 1 1 1 3 5 User s manual 4 2 Rear Side UPS OUTLET Figure 2 Rear Side On ECO rear side there are see figure 2 1 Grounded AC Input power socket IEC C14 type to connect the UPS to the AC utility line 2 Input fuse electrical specification max curr
6. S ECO 0 50 0 70 0 90 1 1 1 3 13 User s manual gt 9 TECNOWARE power systems TECNOWARE s r l www tecnoware com
7. attery Replacement Battery replacement must be performed exclusively by qualified and authorized technical personnel We advise you to follow the steps below explained for greater safety 1 Turn the UPS off and disconnect the AC Input Line for the UPS 2 Unscrew the 4 screws on the UPS bottom side Remove the case cover and so you can access to the battery location Disconnect the battery wires and gently extract the battery from the case The new battery must be exactly the same type as the original one Put inside the new battery and connect it as the original one oS a ae Oe Reassemble the case cover User s manual 10 UPS ECO 0 50 0 70 0 90 1 1 1 3 Battery replacement must be performed exclusively by qualified technical personnel authorized by TECNOWARE TECNOWARE declines any responsibility if this warning is disregarded When replacing batteries replace with the same type and number CAUTION A battery can present a risk of electrical shock and high short circuit current The following precautions should be observed when working on batteries a Remove watches rings or other metal objects b Use tools with insulated handles c Wear rubber gloves and boots d Do not lay tools or metal parts on top of batteries e Disconnect the charging source prior to connecting or disconnecting battery terminals f Determine if battery is inadvertently grounded If inadvertently grounded remove source from gr
8. ay lead to a risk of electric shock to operators 6 Functioning 6 1 Normal Mode The UPS typically works in Normal mode Input mains power is available and its amplitude is within specifications In Normal mode the LINE BATTERY led is always on During Normal mode the UPS recharges the batteries and keeps them in an optimal charging voltage UPS ECO 0 50 0 70 0 90 1 1 1 3 7 User s manual 6 2 Battery Mode The UPS automatically runs in Battery mode if the AC Input Line voltage amplitude gets out of security limits in case of a black out or over voltage low voltage in this case the UPS supplies the required output power by its internal battery and by the Inverter block The UPS automatically returns in Normal mode a few seconds after the AC Input Line is recovered In Battery mode the UPS emits an acoustic alarm signal every 4 seconds and simultaneously the LINE BATTERY led flashes 6 3 Low Battery and Automatic Restart In Battery mode ECO indicates the Low Battery condition whenever the battery reaches a charge level allowing connected devices to operate for approximately one more minute During Low Battery condition the UPS emits an acoustic alarm signal every second and simultaneously the LINE BATTERY led flashes If AC Input does not come back on within few minutes the UPS shuts down automatically thus preventing the batteries from discharging excessively the UPS stops supplying Output power deactiva
9. ent 5 A voltage 250 V 3 Grounded UPS Output receptacles IEC C13 type Electrical Installation and First Start Up We advise you to follow the steps below explained for greater safety 1 Switch off all the devices Personal Computer or other electronic devices that need to be supplied by the UPS 2 Connect the UPS Input socket to the AC line outlet through the Personal Computer supplying cable It is mandatory to ground the AC line outlet according to the Safety Standards Carefully check the grounding make sure that the utility power is available and that its range falls within the UPS specifications refer to the Technical Characteristics chapter 3 Press the ON OFF button on the front panel for about 2 seconds until the UPS emits a brief acoustic signal The UPS turns on the leds the front panel and performs a functioning SELF TEST After some seconds the UPS starts to work in Normal mode the LINE BATTERY led is on Leave the UPS in Normal mode for at least 4 hours in order to completely recharge the batteries User s manual 6 UPS ECO 0 50 0 70 0 90 1 1 1 3 4 Switch the UPS off by pressing again the ON OFF button for about 2 seconds 5 Connect the devices to be supplied to the UPS outputs by using only the included cables Be sure all the devices have the main switch in ON position 6 Turn on the UPS again Check that it starts working correctly and it doesn t signal any sort of anomaly Moreover be
10. l personnel authorized by TECNOWARE TECNOWARE declines any responsibility if this warning is disregarded Warning to the technical personnel authorized for service since internal components are connected to the batteries they will remain powered and therefore dangerous even after the UPS has been disconnected from AC power mains Before any repair or maintenance work disconnect the batteries by removing the positive cable red colour from the positive pole of the battery ANOMALY POSSIBLE CAUSE ACTION TO SOLVE ON OFF button Press the ON OFF button for almost 2 seconds a u Batteries are flat Recharge the batteries for at least 4 hours Electronic board failure Refer to Technical Service Input mains power cable Check the input mains power cable is disconnected Check the presence of the electrical mains The UPS always Input mains fuse is burnt Replace the fuse with another of the same type function on Black out conditions surge Over Voltage or Wait until the AC Input Line returns to normal conditions Low Voltage Battery mode Electronic board failure Refer to Technical Service Battery is not fully Battery Autonomy charged Recharge the battery for at least 6 hours is too short Electronic board failure Refer to Technical Service Continuing Acoustic signal and FAULT condition Refer to Technical Service red ALARM led on If the described anomalie
11. microprocessor giving full guarantee of high reliability Overload protection both in normal mode and in battery mode High performance battery charger which extends the battery medium life ensuring an optimal recharge Start up even if the electrical network is not available Automatic restart after an automatic shut down due to a low battery condition once the AC utility power returns a Adapts automatically to 50 or 60 Hz input frequency UPS ECO 0 50 0 70 0 90 1 1 1 3 3 User s manual Visual and acoustic signals indicating operating mode and alarm fault conditions High efficiency Maximum reliability Smart design and easy to use 3 Receipt and site selection Carefully remove the UPS from its packaging and carry out a meticulous inspection We recommend keeping the original packaging in a secure place in case you need to send the UPS for maintenance purposes In case of transport damage notify the carrier and dealer immediately We recommend paying attention to the below points in order to choose a correct placement for your UPS The UPS is designed to operate in a protected environment e g offices We therefore recommend installing it in a place with very little or no humidity dust or smoke In all circumstances see the Technical Characteristics chapter for environmental specifications and check that the selected area meets these specifications During normal operation
12. n February 2011 version 1 0 No part of this manual may be reproduced even partially without the authorisation of TECNOWARE s r l TECNOWARE s r l reserves the right to change specifications at any time and without notice UPS ECO 0 50 0 70 0 90 1 1 1 3 1 User s manual Safety Warnings vo v vyv WG WW vw A Read this manual carefully and completely before installing and using the TECNOWARE ECO Uninterruptible Power Supply which from here after will also be referred to as UPS This manual should be kept close to the UPS and read before the UPS is installed and used The UPS must be used only by properly trained personnel To ensure correct and safe operations it is necessary that operators and maintenance personnel observe the general safety Standards as well as the specific instructions included in this manual Risk of electric shock do not remove the cover The UPS contains internal parts which are at a high Voltage and are potentially dangerous capable of causing injury or death by electric shock There are no internal parts in the UPS which are user serviceable Any repair or maintenance work must be performed exclusively by qualified technical personnel authorized by TECNOWARE TECNOWARE declines any responsibility if this warning is disregarded Warning to the technical personnel authorized for Service since internal components are connected to the batteries they will remain powered and therefore
13. ound CAUTION Do not dispose of batteries in a fire The batteries may explode CAUTION Do not open or mutilate batteries Released electrolyte is harmful to the skin and eyes It may be toxic 8 4 Operator Safety Whenever the UPS is not responding anymore to original characteristics the UPS must be made non operative and every usage not authorised must be avoided After it will be necessary to refer to qualified technical personnel Original safety characteristics might not be if for example the UPS has visible damage or irregular operation UPS ECO 0 50 0 70 0 90 1 1 1 3 11 User s manual 9 Troubleshooting Alarms and problems you may encounter during operating the UPS are given in the table below Apply the suggestions corresponding to each anomaly as described into the table If your anomaly is excluded or the suggested actions do not solve your problem consult the Technical Service Please give the following information to the Technical Service Model and serial number of the UPS which can be found on the nameplate on the rear of the UPS gt Description of anomaly Risk of electric shock do not remove the cover The UPS contains internal parts that are at a high Voltage and are potentially dangerous capable of causing injury or death by electric shock There are no internal parts in the UPS that are user serviceable Any repair or maintenance work must be performed exclusively by qualified technica
14. rom any type of irregularities in the AC line such as black outs under or over voltages micro interruptions which often cause damage to your Hardware and Software Under normal AC line condition ECO filters frequently occurring electrical disturbances such as transients spikes interferences etc thus protecting all devices connected to the outlets and recharging the batteries in an ideal way In case of anomaly to the AC line the UPS continues feeding the protected equipment Read this manual carefully before using the ECO it includes important safety warnings and useful advices for correct use and installation This manual is a guide that enables you to correctly install and use your UPS This manual includes important SAFETY instructions for the operator for the UPS correct installation and gives useful advice on the product and battery maintenance For any type of problem please refer to this manual before calling the customer service ECO is constantly being developed and improved consequently your unit may differ somewhat from the description contained in this manual This manual includes the following models e ECO 0 50 500 VA e ECO 0 70 700 VA e ECO 0 90 900 VA e ECO 1 1 1100 VA e ECO 1 3 1300 VA In this manual ECO will simply be referred to as UPS 2 General Characteristics ECO has all the advanced features which guarantee maximum reliability and safety All functions are controlled by a
15. s should continue despite the advised troubleshooting or should they manifest in any other form please contact TECNOWARE SERVICE www tecnoware com User s manual 12 UPS ECO 0 50 0 70 0 90 1 1 1 3 Conformity to the European Directives TECNOWARE S r l confirms that ECO models comply with the requirements set out in the Low Voltage Directive Safety 2006 95 EC and following amendments the EMC Electro Magnetic Compatibility Directive 2004 108 EC and following amendments The following standards were applied Low Voltage Directive Safety CEI EN 62040 1 2009 EMC Directive Electro Magnetic Compatibility CEI EN 62040 2 2006 Product Disposal UPS ECO cannot be disposed as an urban waste but must be treated as a separate waste Any violation is indictable with financial sanctions as per in force regulations An incorrect waste disposal or an improper use of the same or of any parts can be damaging for the environment and for human health A correct waste disposal of products having the dustbin symbol marked by a cross help to avoid negative consequences to the environment and to human health yy Lead Batteries ECO models contain lead acid sealed maintenance free batteries The batteries cannot be disposed as an urban waste but must be treated in conformity with 2006 66 CE European Directive any violation is indictable with financial sanctions as established into 2006 66 CE European Directive UP
16. tes control panel indication and goes to a waiting state Once AC Input comes back on the UPS restarts automatically and after some seconds it goes back to work in Normal mode After a complete discharge the UPS needs 4 hours to recharge completely the batteries The UPS recharges batteries automatically if it works in Normal mode 6 4 Load Control During the functioning in Battery Mode if the Output load is higher than nominal value Overload condition the UPS may automatically switch off protecting itself from this anomalous situation In this case the user must reduce power within the specifications by disconnecting the devices that cause the Overload condition the chapter Technical Characteristics as this may damage the unit In this case the warranty is void Do not connect a load greater than rated value to the UPS see POWER specifications in 6 5 Fault Condition The UPS indicates the Fault condition by lighting of the Alarm led and by emitting a continuous acoustic alarm During Fault condition the UPS doesn t supply Output power and so all the supplied devices are switched off User s manual 8 UPS ECO 0 50 0 70 0 90 1 1 1 3 7 Technical Characteristics 5 500 VA 700 VA 900 VA 1100 VA 1300 VA ower 300 W 420 W 540 W 660 W 780 W Personal Personal Personal Personal Personal Computer with Comp
17. uter with Computer with Computer with Computer with 350W PSU 450W PSU 550W PSU 600W PSU 650W PSU Recommended for 250W real 350W real 450W real 500W real 550W real power power power power power LCD Monitor LCD Monitor LCD Monitor LCD Monitor LCD Monitor 40W 40W 60W 60W 100W Technology Easy Interactive Nominal Input Voltage Single phase 230 Vac Input Voltage Range 15 23 Input Output Frequency 50 60 Hz automatic selection Input Frequency Range 5 Nominal Output Voltage Single phase 230 Vac Output Voltage Regulation Normal mode Aennpul Output Voltage Regulation 4 5 Battery mode 3 Output Inverter Waveform Modified Sinewave Accepted Overload lt 130 CE Certifications Standards CEI EN 62040 1 2009 Low Voltage Directive CEI EN 62040 2 2006 EMC Directive Efficiency 92 Battery Type Lead acid sealed free maintenance Number of batteries 1 Nominal Battery Voltage 12 Vdc EEE ON T 12 Vdc 4 5 Ah 12 Vdc 5 A 12 Vdc 7 2 Ah 12 Vdc 7 2 Ah 12 Vdc 9 Ah I 6 cells 6 cells 6 cells 6 cells 6 cells Backup Time typical 10 min Battery Charge Time typical 4 hours Audible Noise at 1 meter lt 40 dBA Cooling Natural Environmental Operative Specification Temperature 0 40 C Humidity 0 95 without condensation Altitude max 3 000 mt Output sockets 2 Output sockets IEC type Dimension W x H x D 20 7 x 8 3 x 22 8 cm
Download Pdf Manuals
Related Search