Mitsubishi Electric CP9600DW photo printer
Contents
1. gt O lt SNILOOHS ATENOdL SUSdHLO SLNALNOO SPECIAL FEATURES See SPECIAL FEATURES 5 PRINT SIZES ARE AVAILABLE DEPENDING ON THE PURPOSE 5 printing sizes 9x13 3 5x5 max 89 x 127 mm 10x15 4x6 max 102 x 152 mm 13x18 5x7 max 127 x 178 mm 15x20 6x8 max 152 x 203 mm and 15x23 6x9 max 152 x 229 mm are selectable 600 DPI HIGH RESOLUTION CP9600DW has a high resolution of 600 DPI for precise illustrations and sharp photographic images LARGE CAPACITY PRINTING Maximum of 680 prints per roll for 9x13 3 5x5 is offered Large economical print capacity per roll reduces frequency of exchanging paper and ink ribbon HIGH QUALITY PRINTING CP9600DW is a dye sublimation thermal transfer color printer which produces superior high quality images It also produces a continuous tone at 256 gradient for each of Y M and C and 16 7 million colors HIGH SPEED PRINTING Normal printing speed is approx 21 seconds in 9x13 3 5x5 300 DPI mode print Use of roll paper shortens the time for installing and removing ADDITIONAL FEATURES COMPATIBLE WITH A VARIETY OF INTERFACES AND SYSTEMS 1 Input and output of control signals using the Hi Speed USB Ver 2 0 interface Az 2 Newly developed printer driver which reduces PC processing time CERTIFIED USB SNOILNVOAUd n gt c D m a Q O Z Z m O O Z U J im gt gt O Z SNILOOHS ATENOdL2. SUSdHLO SLNALNOO UNPACKING UNPACKING Take the printer out of the box by the following procedures Make sure to check the accessories 1 Open the top of the box SNOILNVOAUd 2 Remove the accessories together with upper cushions 3 Hold the handles of the cardboard and pull it up carefully to take the printer together with the lower cushions out of the box Make sure to pull the cardboard straight up NOTE This printer is about 17 kg in weight Handle it with care m gt c D m O Q O Z Z m O O Z U T D 1l gt gt O Z 4 Separate the printer from the cushions Hold the parts indicated by the arrows and pull the printer straight up SNILOOHS ATENOdL 5 Unwrap the packing Keep the cushions for transporting the printer again When moving this printer hold the lower front part and the handle on the rear side saJ3HLO E CONTENTS The accessories are contained in the upper cushions Check the contents Paper Quick setup Paper strip CD ROM Print outlet Sheet for Label for catcher guide bin cover paper guide installation SLNALNOO Power cords Ink cassette Paper flanges Spacers The ink cassette is contained in the printer 6 FEATURES AND FUNCTIONS FRONT PANEL POWER BUTTON Use to switch the power ON and OFF Press to turn on power Press again to turn off power PAPER STRIP BIN Holds the pa
3. MITSUBISHI E ELECTRIC DIGITAL COLOR PRINTER MODEL CP9600DW OPERATION MANUAL THIS OPERATION MANUAL IS IMPORTANT TO YOU PLEASE READ IT BEFORE USING YOUR DIGITAL COLOR PRINTER DIGITAL COLOR PRINTER Hereby Mitsubishi Electric Corporation declares that this digital color printer is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC This digital color printer complies with the requirements of the EC Directive 89 336 EEC 73 23 EEC 93 68 EEC The electro magnetic susceptibility has been chosen at a level that gains proper operation in residential areas on business and light industrial premises and on small scale enterprises inside as well as outside of the buildings All places of operation are characterised by their connection to the public low voltage power supply system INFORMATION This Class A digital apparatus complies with Canadian ICES 003 Cet appareil numerique de la classe A est conforme a la norme NMB 003 du Canada WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE SNOILNVOAUd WARNING Use the included AC power cord so as not to interfere with radio and television reception If you use other cables it may cause interference with radio and television reception CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK
4. m O O Z U J 1 gt gt O Z OPERATING AMBIENT TEMPERATURE RANGE The operating ambient temperature range is 5 C 40 C 41 F 104 F and the humidity of 30 80 RH When using the unit on the system rack be sure to keep this ambient temperature inside the rack When the printer is used in a low temperature it may take some time to start printing FOR LONG OPERATING LIFE UNSUITABLE MATERIALS FOR THE DIGITAL COLOR PRINTER Coat flaking and deformation are likely to occur if the unit is wiped with chemical dusters benzine thinner or any other solvent if rubber or PVC items are left in contact with the unit for extended duration or if the unit is sprayed with insecticide SNILOOHS A1TENnOdL CARE OF THE CABINET Unplug and clean with a soft cloth slightly moistened with a mild soap and water solution Allow to dry completely before operating Never use petroleum base solutions or abrasive cleaners saJ3JHLO HEAD ABRASION The thermal head like the video head wears out When it is abraded it becomes hard to print out fine details of the picture In such a case it is necessary to replace the thermal head Consult with the sales dealer for replacing the head CONNECTING DEVICES Read thoroughly Operating Precautions of the instruction booklets for the devices connected with the Digital Color Printer The power cord must be disconnected after printing is over S1N3LNO9 CAUTION ON RELOCATING When
5. the spacers see the Quick Setup Guide Remove the cushions put between the paper flange and spacer when use them How to attach and remove the spacers 1 Turn the spacer until the latches are unlocked 2 Remove the spacer with the paper flange s stoppers retracted When you use the print paper with which the spacers have to be used attach the spacers to the paper flanges by reversing the above mentioned removal procedure as shown right 1 Attach the supplied paper flanges to both sides of the print paper When you pinch the latches on the paper flange the stoppers retract into the shaft Attach the flanges to the print paper with the stoppers retracted Make sure that the flanges are attached to the print paper securely and release the latches NOTE Take care not to pinch your fingers Do not remove the sticker on the print paper yet Do not slacken the paper Any slack in the print paper may degrade the print quality CAUTION When placing the print paper remove one flange and keep the print paper upright on its side with no flange When you put the print paper sideways it may roll and fall This may cause injury NOTE Do not touch the thermal head Fingerprints or dust on the thermal head will degrade the print quality latches INCORRECT CORRECT 11 SNOILNVOsAUd m gt c D m O Q O Z Z m O OQ Z U U D u gt gt O Z SNILOOHS A1TENOdL
6. Color Printer is designed to operate on 120V AC 50 60Hz in the U S A and Canada and 220V 240V AC 50 60Hz in Europe Never connect to any outlet or power supply having a different voltage or frequency WARNING THIS APPARATUS MUST BE EARTHED AVERTISSEMENT CET APPAREIL DOIT ETRE MIS A LA TERRE PROTECTIVE MEASURES IF ABNORMALITIES ARISE Use of the unit during emission of smoke or abnormal sounds without adopting countermeasures is dangerous In sucha case unplug the power cord from the source outlet immediately and request maintenance service from the sales dealer SNOILNVOAUd NEVER INSERT ANY OBJECT INTO THE UNIT Foreign objects of any kind inserted into this unit constitute a safety hazard and can cause extensive damage DO NOT PLACE ANYTHING ON THE DIGITAL COLOR PRINTER Heavy objects placed on the Digital Color Printer can cause damage or obstruct proper ventilation PROTECT THE POWER CORD Damage to the power cord may cause fire or shock hazard When unplugging hold by the plug only and remove carefully DO NOT PLACE WATER CONTAINERS ON THE UNIT Do not place flower vases and other water holding containers on the device If for some reason water seeps to the inside of the unit unplug the power cord from the source outlet and contact the sales dealer If used without corrective measures the unit may be damaged In the interest of safety avoid handling of liquids near the unit m gt c D m O Q
7. NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL gt c D m O Q O Z Z m O O Z U J u gt gt O Z The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the produc s enclosure that may be of sufficient magnitude to constitute the risk of electric shock SNILOOHS J TENnOdL The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance saJ3JHLO The Caution hot surface symbol indicates that the marked item may be hot and should not be touched The Electro Static Discharge ESD warning symbol indicates that trouble including equipment malfunction due to static electricity may occur in certain conditions SLNALNOO The ON OFF symbol indicates connection to or disconnection from the mains at least for mains switches The Alternating current symbol indicates that the equipment is suitable for alternating current only Opee CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class A digital
8. O Z Z m O O Z U J 1 gt gt O Z DO NOT REMOVE THE CABINET Touching internal parts is dangerous besides it may lead to malfunction Contact the sales dealer to carry out internal checks and adjustments Before opening the cover for eliminating a jammed paper etc be sure to disconnect the power cord plug SNILOOHS ATENOdL UNPLUG THE POWER CORD DURING A LONG ABSENCE Turn off the main power switch and unplug the power cord during a long absence WHEN TRANSPORTING THE UNIT When transporting the unit remove the ink ribbon and print paper from the unit See INSTRUCTIONS FOR TRANSPORTATION on page 19 SUSdHLO BE CAREFUL AROUND PRINT PAPER EXIT SLOT Don t insert your hand or any material into the paper exit slot during printing Do not touch the cutter blade inside the paper exit slot Otherwise your finger will be injured DO NOT TOUCH THE THERMAL HEAD AND METAL PART ON THE MOTOR COVER Do not touch the thermal head and the metal part on the motor cover located inside the unit They are heated to high temperature and may cause burns or injury when touched SLNALNOOD WHEN PLACING THE PRINT PAPER REMOVE ONE FLANGE AND KEEP THE PRINT PAPER UPRIGHT ON ITS SIDE WITH NO FLANGE When you put the print paper sideways on a table etc it may roll and fall This may cause injury CONNECTION CABLES Use the provided power cord SAFETY PRECAUTIONS REMOVE THE PAPER STRIP BIN WHEN OPENING OR CLOS
9. device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense SNOILNVOAUd Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device WARNING In the USA or Canada use the AC power cord according to the recommen dations as below in order to comply with UL60950 1 and CAN CSA C22 2 No 60950 1 03 Connect to the 120V receptacle of the room or the host equipment The AC power cord should be UL or CSA approved and consist of type SVT size 16 or 18AWG length 2 m or shorter cord with IEC60320 1 C13 type 125V 10A or higher rating connector and NEMA 5 15 type 125V 10A or higher rating plug WARNING In Europe use the AC power cord according to the recommendations as below in order to comply with EN60950 1 Connect to the 230V receptacle of the room or the host equipme
10. is used up The ink ribbon which is not available to this printer is installed e Replace the ink ribbon with a new one The print paper is not installed The print paper is used up e Install new print paper The combination of the ink ribbon and the print paper is incorrect e Use a correct combination of the ink ribbon and the print paper When ALARM or PAPER INK RIBBON indicator illuminates or blinks open the door and carry out the above countermeasures If the indicator is not turned off by closing the door carry out the paper feed amp cut me gt C D m O Q O Z Z m O O Z U U D 1 gt gt O Z l SNILOOHS A1ENOdL aa saJHLO Note If an error occurs while the continuous printing through the PC is ongoing it is resumed after the COOLING indicator goes off SLNALNOOD 17 ERROR MESSAGES AND COUNTERMEASURES OVERCOMING PAPER JAMS 1 Press the DOOR OPEN button to open the door Make sure that the power is turned on before opening the door If the door does not open turn off the power and turn it on again Then press the DOOR OPEN button again SNOILNVOsAdd 2 Remove the ink cassette Push down the ink cassette as shown by the arrow and pull it out 3 Take out the print paper When taking the print paper out pull it up toward you 7 gt C JJ m V O O lt lt m O O lt V U JJ m gt gt O lt 4 Cut off
11. slack from the print paper If you carry out the following steps without eliminating the slack the print paper may be damaged Black cover BEFORE OPERATION INSTALLATION OF INK RIBBON W INSTALLING THE INK RIBBON After installing the print paper install the ink cassette into this unit Before installing the ink cassette into this unit load the ink ribbon in the ink cassette SNOILNVOsAdd NOTE Place the ink cassette on a flat surface when loading the ink ribbon Select a place that is free of dust when loading the ink ribbon Dust or dirt settling on the ink ribbon results in poor print quality Make sure that the shafts of the ink ribbon fit into the ink cassette firmly 1 Load the ink ribbon in the ink cassette as shown below e Make sure to load it in the correct position Ink ribbon Handle Ink cassette Gear ivory m gt c D m N Q O Z Z m O O Z U J u gt gt O Z W INSTALLING THE INK CASSETTE 1 Place the ink cassette containing the ink ribbon in the position as shown right Place the ink cassette on the print paper with the shaft thicker one around which the ink ribbon is wound located to the front Align the arrows marked on the sides of ink ra cassette with those on the unit Thermal head inside Place the rear of the ink cassette along the guides that are provided inside the unit SNILOOHS A1TEGNOdL Make sure to set the ink ribbon roller
12. CIFICATIONS JJ Class Digital Color Printer Al Model CP9600DW a Printing method Sublimation Dye Thermal Transfer line print 3 color faces progressive printing yellow magenta and cyan and surface lamination z Print s resolution 600 x 600 DPI DPI Dots per inch 0 Dot resolution 9x13 3 5x5 2152 x 3144 dots 300 DPI mode 1076 x 1572 dots a 10x15 4x6 2458 x 3736 dots 300 DPI mode 1228 x 1868 dots m 13x18 5x7 3144 x 4256 dots 300 DPI mode 1572 x 2128 dots a 15x20 6x8 3736 x 4846 dots 300 DPI mode 1868 x 2422 dots 15x23 6x9 3736 x 5462 dots 300 DPI mode 1868 x 2730 dots Mm Print size 9x13 3 5x5 89 x 127mm without frame 10x15 4x6 102 x 152mm without frame oO 13x18 5x7 127 x 178mm without frame z 15x20 6x8 152 x 203mm without frame lt 15x23 6x9 152 x 229mm without frame 0 Gradations 256 8 bits for each color About 16 7 million colors O Printing time 9x13 3 5x5 Approx 51 sec sheet 300 DPI mode Approx 21 sec sheet 5 10x15 4x6 Approx 57 sec sheet 300 DPI mode Approx 23 sec sheet T 13x18 5x7 Approx 89 sec sheet 300 DPI mode Approx 33 sec sheet aA 15x20 6x8 Approx 104 sec sheet 300 DPI mode Approx 38 sec sheet U 15x23 6x9 Approx 111 sec sheet 300 DPI mode Approx 41 sec sheet z Supply method Automatic gt Interface Hi Speed USB Ver 2 0 O Power supply 220 240 V AC 50 60 Hz 120 V AC 50 60
13. Front Oane ea E de uaaiceareues vs 4 Sideand rear 9 5 Se ee ee ee EE 8 oE e eee EE P E E TE E E E E ee eee ee ee 9 10 J Connection with USB data signal equipment ccceeeeeeeeeeeeeeeeees 9 U Setting OF DIP SWitChNES ssscsiscessrasrenionidorrssssn isese iea 10 OO et BO sssi e ora 11 16 S installation of print paper a scivstueveri sacks cstcasstrenseieteranten dete dianian n 11 12 S installation of INK WO ct ecsinensecns eitesautecestenteestenarepnanetieseiatctearacaacaeesncs 13 14 m Handling of paper ink ribbon Set cccccceeeeeeeeeceeeeeeeeeeeseaeeeeeeeeseaeeees 15 9 Installation of printer driver osccdestecnswcentenvetaicedsnuiscndacuctadnenteasauboccudensenecenane 16 O Error messages and countermeasures 00ceeeeeeeeeeeeeeeeeeeeeeeeeeeenees 17 19 o Indications on the front panel and countermeasures sseeeeeeeeeeees 17 AY Overcoming paper JAMS sacaicccssntissesncncateassnsdedcadineedeieatontenctensheneaieiersndenee 18 1l Before calling for service cccccccsseceecceeeeeceeeeeecseaeeesseaueeeeseansenensaeeees 19 D gt instructions for transportatioi ccscsstanccncinexnesennsapensicnamnicanvsiahenseeapaatiaseiennne 19 m PS INN PAE E EE T A E EEA A N 20 NG ABN a serrian anaiei aiaia iaaiiai 21 U L J OO oc Sf m saJ3HLO S1N3LNO9 SAFETY PRECAUTIONS rir rrr RR In the interest of safety please observe the following precautions POWER REQUIREMENT This Digital
14. Hz lt Power consumption 1 6 A 220 240 V AC 50 60 Hz 2 9 A 120 V AC 50 60 Hz during printing TEE 0 3 A 220 240 V AC 50 60 Hz 0 4 A 120 V AC 50 60 Hz when not printing T J Operating conditions Temperature 5 C 40 C 5 Humidity 30 80 RH no dewing 4 z Installation conditions Operating attitude Horizontal 5 m Outside dimensions 300 W x 365 D x 325 H mm Weight Approx 17 kg excluding accessories Standard accessories Power cords for 120 V and 230 V Ink cassette 1 CD ROM 1 Paper flange 1 set Spacers 2 Quick setup guide 1 Paper strip bin 1 Paper catcher 1 Print outlet cover 1 Sheet for paper guide 1 Label for installation 1 W Contents of CD ROM e Operation manual e Printer driver e PRINTER DRIVER GUIDE e Adobe Reader Adobe the Adobe logo and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries O Z m V 21 MITSUBISHI ae ELECTRIC MITSUBISHI DIGITAL ELECTRONICS AMERICA INC 9351 Jeronimo Road Irvine CA 92618 U S A Phone 949 465 6000 Mitsubishi Electric Europe B V UK Branch Travellers Lane Hattield Herts AL10 8XB England U K Phone 44 0 1707 276100 FAX 44 0 1707 278755 German Branch Gothaer Strasse 8 40880 Ratingen Postfach 1548 40835 Ratingen Germany Phone 49 2102 486 9250 FAX 49 2102 486 7320 French Branch 25 Bouleva
15. ING THE DOOR When you open or close the door with the paper strip bin installed the bin may be removed and fall This may cause injury or damge INSTALLATION LOCATIONS MAINTAIN GOOD VENTILATION Ventilation slots and holes are provided on the rear and both sides of this unit Place the unit on a hard and level surface and keep a space between the unit and the walls to ensure proper ventilation When putting the unit on the system rack take a space between the unit and the back and sides of the rack SNOILNVOAUd SUITABLE LOCATIONS Avoid shaky places or hot springs areas where hydrogen sulfide and acidic ions are likely to be generated AVOID PLACES WITH HIGH HUMIDITY AND DUST Do not place the unit at a high humidity and dusty locations They can cause extensive damage to this unit Avoid places where the unit is likely to be exposed to oily fumes and vapors AVOID PLACES LIKELY TO BE EXTREMELY HOT Places exposed to direct sunlight or near heating appliances can attain extremely high temperatures which may deform the cabinet or can become a prime cause of damage PLACES THE UNIT ON A HORIZONTAL LEVEL The unit is likely to be affected if it is placed in slanted conditions or in an unstable places PROTECT AGAINST DEW FORMATION In extremely cold regions if the unit is moved quickly from an extremely cold place to warmer one dew is likely to be formed If dew is formed printing is not possible m gt c D m O Q O Z Z
16. LNVOsAdd Product name Required operating system CPD9600X Applies for Microsoft Windows 2000 or Windows XP operation system W Refer to the PRINTER DRIVER GUIDE in the CD ROM for installing the printer driver Microsoft Windows Windows 2000 and Windows XP are the registered trademarks of Microsoft Corporation in the U S A and other countries 16 m gt c D m N Q O Z Z m O O Z U J u gt gt O Z ONILOOHS A1ENOdL SUSdHLO SLNALNOO ERROR MESSAGES AND COUNTERMEASURES INDICATIONS ON THE FRONT PANEL AND COUNTERMEASURES W if for some reason printing is not possible or an error occurs during printing the indicators on the front panel will illuminate or blink In this case follow the procedure described below In case of an error during printing unless you turn off the unit the unit resumes printing automatically when the error is corrected SNOILNVOsAdd l l Steadyon off Blinking Depends on the previous condition PAPER DATA INK RIBBON ATA READY COOLING Causes and Countermeasures The door is open e Close the door A paper jam occurs e Refer to Overcoming paper jams Y The power is turned off during printing process e Turn on the power and carry out the paper feed amp cut Me oN The temperature of the thermal head is too high e Wait until the indication goes off Note The ink ribbon is not loaded The ink ribbon
17. ality Leave the print paper in the room to stabilize its temperature before using it e Ifyou repeat the FEED amp CUT procedure more than the designated number of times while installing the print paper the indicated number of prints may not be made In addition if you replace the print paper before it is used up the indicated number of prints may not be made Mi AFTER PRINTING e Ifthe paper absorbs nonvolatile organic solvents alcohol ester ketone etc the print may be discolored e Discoloration of prints is accelerated if the print paper comes into contact with soft vinyl chloride such as transparent tape e Avoid storing prints in direct sunlight or places with high humidity Mi STORAGE OF PAPER INK RIBBON SET e Do not store the print paper and ink ribbon in the container made of soft polyvinyl chloride They may be discolored because of chemical reaction e Store the print paper and ink ribbon out of direct sunlight and away from heating appliances in a cool dark place where the temperature is 5 C to 30 C and the humidity is 20 to 60 RH 15 SNOILNVOsAdd m gt c D m N Q O Z Z m O O Z U J u gt gt O Z ONILOOHS A1ENOdL SUSdHLO SLNALNOO BEFORE OPERATION INSTALLATION OF PRINTER DRIVER W The printer driver is required to print the data from the personal computer connected with this unit The printer driver for Windows is supplied with this unit SNOI
18. at the time this button is pressed is completed the printing process is canceled FEED amp CUT BUTTON When you keep pressing this button for more than 1 second the print paper is fed and cut PAPER CATCHER You may stack about 10 prints on this paper catcher See the next page for the installation of this paper catcher When using the print paper of 13x18 5x7 15x20 6x8 or 15x23 6x9 do not install the paper catcher NOTE It is recommended to remove the prints stacked on the paper catcher frequently If the prints are not removed frequently a paper jam may cause SNOILNVOAdd O lt lt m O a V JJ m gt gt O lt SNILOOHS A1TENOdL saJHLO SLNALNOO FEATURES AND FUNCTIONS SIDE AND REAR PANEL J m O gt C O Z O m 4 O amp LEFT SIDE REAR JJ m gt USB TERMINAL HANDLE FOR TRANSPORTING z Use to connect the USB cable When transporting this unit hold this handle and the lower See page 9 front part of this unit DIP SWITCHES POWER SOCKET AC LINE re Use to set various functions of this unit See page 10 Use to connect the provided power cord Insert the cord S 5 firmly Oc f m saJHLO INSTALLING THE PAPER CATCHER Hook the paper catcher by its latches When using the print paper of 13x18 5x7 15x20 6x8 or 15x23 6x9 do not install the paper catcher Holes
19. cut mode has been selected hold down the FEED amp CUT button for 1 second or longer Repeat the manual feed amp cut three times When the print paper with the post card printing on its reverse side is installed repeat this procedure five times For how to select the auto feed amp cut mode see Setting of DIP switches on page 10 Installation of the print paper and the ink ribbon is completed NOTE e Make sure to replace the print paper and the ink ribbon at the same time e When replacing them throw away the paper chips in the paper strip bin 14 SNOILNVOAUd m gt c D m N Q O Z Z m O O Z U J u gt gt O Z SNILOOHS ATENOdL saJ3HLO S1N3LNO9 BEFORE OPERATION HANDLING OF PAPER INK RIBBON SET Mi BEFORE PRINTING e Fingerprints or dust on the paper s printing surface may degrade the print quality and cause paper jams When the manual feed amp cut mode has been selected repeat the FEED amp CUT procedure three times after replacing the print paper When the print paper with the post card printing on its reverse side is installed repeat five times If you omit cutting the print paper by the FEED amp CUT procedure first two or three prints may not be printed partly because of finger oil or dirt e When the print paper is abruptly transferred from a cool place to a hot place vapor or dew is generated on the paper s surface causing paper jams or degraded print qu
20. for 9 x 13 size paper S1N3LNO9 Paper width 127 mm Holes for 10 x 15 size paper Paper width 152 mm CONNECTIONS CONNECTION WITH USB DATA SIGNAL EQUIPMENT E CONNECTING TO PERSONAL COMPUTER EXAMPLE Connect this unit to a personal computer as shown below To USB port gt D m O gt C O Z TI gt Cc m Personal computer Digital color printer paa NOILVdVdsdd ATENOdL SUSdHLO SLNALNOO CONNECTIONS SETTING OF DIP SWITCHES Mi SETTING DIP SWITCHES OFF ON All the switches are set to OFF at the time of shipment from the factory nN Turn off the power before changing the DIP switch settings O1 O N 00 Switch No Setting 1 OFF Auto feed amp cut mode When the door is closed after the print paper is installed with this unit powered on this unit automatically carries out paper feed amp cut operation ON Manual feed amp cut mode ON Plo ENSS ON 3 4 Set this switch to OFF on ee ON OFF Set this switch to OFF e Pe 10 D m O gt C O Z TI gt Cc JI m o paa NOILVdVdsdd ATENOdL SUSdHLO SLNALNOO BEFORE OPERATION fi Before printing 1 Install the print paper to this unit See below 2 Install the ink ribbon to this unit See page 13 14 INSTALLATION OF PRINT PAPER Spacers Mi The spacers are attached to the paper flanges For the necessity of
21. g the thermal head Inside SNILOOHS A1TENOdL NOTE z m The thermal head may be damaged if you touch it while static electricity builds up Outside on your body 152 mm WE WHEN USING THE CLEANING RIBBON CR9000 ines When you use print paper of 152 mm 6 with after using that of 127 mm 5 thermal head cleaning with a cleaning ribbon may be required Printing If one or two lines appear on the printing surface as shown right when printing on the print surface paper of 152 mm 6 width clean the thermal head using the optional cleaning ribbon PE z Cleaning is not required when about 12mm dibout 12mm you use print paper of 127 mm 5 width after using that of 127 mm 5 you use print paper of 152 mm 6 width after using that of 152 mm 6 or you use print paper of 127 mm 5 width after using that of 152 mm 6 Print paper of 127 mm 5 width 9x13 3 5x5 13x18 5x7 Print paper of 152 mm 6 width 10x15 4x6 15x20 6x8 15x23 6x9 NOTE When the symptom of poor print quality is not corrected even after the head is cleaned CR9000 SLNALNOO replace the thermal head Contact your dealer PAPER FLANGE CLEANING Clean the parts that contact the print paper sides as shown right Wipe the parts carefully with tissue paper dampened with a small amount of alcohol Cleaning part 20 SPECIFICATIONS LY SPE
22. nt The AC power cord should be VDE approved and consist of core size 1mm or bigger length 2 m or shorter cord with IEC60320 1 C13 type 250V 10A or higher rating connector and CEE 7 VII type 250V 10A or higher rating plug NOILVdVdsdd SNOILOANNOO SsdgdNlVsas SNILOOHS J TEsNnOdL saJ3HLO WARNING The socket outlet shall be installed near the equipment and shall be easily accessible Note This symbol mark is for EU countries only This symbol mark is according to the directive 2002 96 EC Article 10 Information for users and Annex IV Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and compo nents which can be recycled and reused SLNALNOO This symbol means that electrical and electronic equipment at their end of life should be disposed of separately from your household waste Please dispose of this equipment at your local community waste collection recycling centre In the European Union there are separate collection systems for used electrical and electronic product Please help us to conserve the environment we live in CONTENTS eee CONTENTS oO m E en E ee ee ee ee ee 1 Q Saleiy DISC AMUONS snc sanccasannscasecsnnnananinadineeaceraianianceasoantagentednaacnenesntaatenns 2 4 S Special featUreS ee ee ee a eae nh eee eee eee nee 5 2 Beee eE EE E E A AE ES 6 k Features and TUNCHONS sisi cnctincssresedssiuvcranerdintiddenansistantnenmriacpesmeiaradeiersenns 7 8
23. o the outlet firmly The protective circuit may be working Turn off the power and wait for about two minutes Then turn on the power again SNOILNVOsAdd The door doesn t close Are you turning off the power during printing procedure Turn on the power and then close the door The image is not printed Is the image data sent to this unit Make sure that the image data is sent to this unit Is the print paper or the ink ribbon used up Check them Is the ink cassette installed correctly Install the ink cassette correctly me gt c D m O Q O Z Z m O O Z U U D a gt gt O Z SNILOOHS ATEGNOdL INSTRUCTIONS FOR TRANSPORTATION When transporting this unit for some reason such as repair follow the instructions below SYSHLO 1 Use the original packaging The genuine package unit may not endure more than one round trip If the unit is transported with the package unit more than one round trip it may not be guaranteed Purchase another package unit when transporting this unit again Pack the unit with all the accessories ink ribbon print paper ink cassette and paper flanges removed 2 Turn off the power after the PAPER INK RIBBON indicator blinks After removing all the accessories close the door with the printer s power on After the PAPER INK RIBBON indicator blinks turn the power off 3 If the ink ribbon print paper or ink cassette can not be taken out consult wi
24. per chips generated by margin cut To prevent jamming the chips at the print outlet throw away the chips frequently NOTE Remove the bin before opening the door If the door is opened with this bin attached the printer or this bin may be damaged PRINT OUTLET The printed paper comes out here DOOR OPEN BUTTON When you press this button while the power is on the door will open in about five seconds DOOR Open this door when installing print paper or ink ribbon Press the DOOR OPEN button to open the door POWER INDICATOR When the power is turned on the indicator illuminates ALARM INDICATOR This indicator illuminates or blinks when a paper jam occurs or the door is open See page 17 PAPER INK RIBBON INDICATOR When an error concerning the ink ribbon or print paper occurs this indicator illuminates or blinks See page 17 PAPER STRIP BIN Hook the paper strip bin by its latches A gt B To attach To remove B gt A DATA INDICATOR This indicator blinks during data transfer It illuminates during printing READY INDICATOR This indicator illuminates when this unit is ready to accept the data It also illuminates during data transfer It blinks during print canceling procedure COOLING INDICATOR When the unit is overheated this indicator blinks See page 17 CANCEL BUTTON Press this button for more than 1 second to cancel continuous printing After the ongoing printing
25. rd des Bouvets 92741 NANTERRE cedex France Phone 33 1 55 68 55 00 FAX 33 1 55 68 57 31 Italian Branch Centro Direzionale Colleoni Palazzo Sirio ingresso n 1 Viale Colleoni 7 20041 Agrate Brianza Milano Italy Phone 39 03960531 FAX 39 0396053214 Benelux Branch Nijverheidsweg 23a 3641 RP Mijdrecht The Netherlands Phone 31 0 297 282461 FAX 31 0 297 283936 Spanish Branch Barcelona Ctra de Rub 76 80 Apdo 420 08190 Sant Cugat del Vall s Barcelona Spain Phone 34 93 565 3154 FAX 34 93 589 4388 Please contact the nearest Mitsubishi sales branch to get DOC Declaration of Conformity of the EC Directive 1999 5 EC Manufactured by Mitsubishi Electric Corporation 1 Zusho Baba Nagaokakyo city Kyoto Japan WE919C150A7
26. saJ3HLO SLNALNOO BEFORE OPERATION 2 Press the POWER button to turn on the power SNOILNVOsAdd 3 Press the DOOR OPEN button to open the door Take the ink cassette in the printer out 4 Install the print paper into the unit Make sure to install the print paper firmly NOTE Install the print paper into the unit slowly If it is dropped along the ditches the unit or accessories may be damaged CAUTION Do not touch the thermal head right after printing because it is extremely hot Otherwise you may get burned or injured n gt C JJ m V O O lt lt m O O lt V JJ m gt gt oe lt NOTE Note that the thermal head is quite sensitive to static electricity When you touch the thermal head while carrying SNILOOHS ATENOdL Static electricity on your body the thermal head may be damaged Direction of paper insertion 5 Remove the sticker insert the print paper between the rollers as shown right and feed the print paper until it reaches the black cover e Remove the sticker before inserting the print paper between rollers Make sure to insert the paper straight NOTE e Keep the roller clean Dirt on the roller may degrade the print quality NOTE e When taking the print paper out pull it up toward you e Make sure to turn on the power before replacing the print paper saJ3HLO Print paper S1N3LNO9 e Make sure to eliminate any
27. th your dealer SLNALNOO 19 CLEANING Cleaning as indicated below will help maintain stable printer operation and extend the printer s life i small amount of alcohol Preparations Alcohol isopropyl alcohol ZE Tissue paper Fold in half about four times and use the folded side to clean LA Cleaning part Other Cleaner pen option Cleaning ribbon option How to fold tissue paper Please ask the dealer about options Ep lt 9 PREPARATIONS FOR CLEANING _ lt lt 1 Press the POWER button to turn on the power Gigenerpen 2 Press the DOOR OPEN button to open the door 3 Remove the ink cassette 4 Take out the print paper 5 Press the POWER button to turn off the power Make sure to turn off the power before cleaning THERMAL HEAD CLEANING Clean the heat generating part below the thermal head Wipe the head cleaning part carefully with tissue paper dampened with a small amount of alcohol NOTE Do not damage the thermal head When the poor print quality is not corrected even if the head has been cleaned replacement of the thermal head may be required Contact your dealer J m O gt C O Z U TI gt c D m a Q O Z Z m O O Z U U D a gt gt O Z ta CAUTION Cleaning part of thermal head Thermal head is hot right after printing Wait until the head cools before cleanin
28. the defective part of the print paper with scissors NOTE Make sure to cut off the printed part of the print paper Failure to do this may result in the ink ribbon sticking to the print paper and being torn SNILOOHS A1ENOdL 5 Install the print paper and the ink cassette with the ink ribbon Refer to pages 11 14 SYHSHLO 6 Push the center of the door to close The print paper setting is initialized two minutes after you close the door When the auto feed amp cut mode has been selected the FEED amp CUT procedure is repeated three times after you close the door When the print paper with the post card printing on its reverse side is installed the FEED amp CUT procedure is repeated five DOOR OPEN cancel Feebacut times Sor SLNALNOO HE When the manual amp cut mode has been selected When the manual feed amp cut mode has been selected hold down the FEED amp CUT button for 1 second or longer Repeat the manual feed amp cut three times When the print paper with the post card printing on its reverse side is installed repeat this procedure five times For how to select the auto feed amp cut mode see Setting of DIP switches on page 10 18 ERROR MESSAGES AND COUNTERMEASURES BEFORE CALLING FOR SERVICE For the following symptoms check the unit again before calling for service The power is not turned on Is the power cord plug disconnected from the outlet Connect the power cord plug t
29. to the ditches firmly Turn the ivory roller to eliminate any slack SHSdHLO Arrows SLNALNOO Guides 13 BEFORE OPERATION A ges 2 Push the ink cassette toward the back of the unit Thermal head inside Hold the handle of the ink cassette and push it straight toward the back of the unit Then raise it until you hear a click to secure it in the ink cassette holder NOTE If the ink ribbon is used up repeat the steps 1 to replace the print paper and the ink ribbon 3 Push the center of the door to close The print paper setting is initialized two minutes after you close the door When the auto feed amp cut mode has been selected the FEED amp CUT procedure is repeated three times after you close the door When the print paper with the post card printing on its reverse side is installed the FEED amp CUT procedure is repeated five times NOTE When closing the door push it until a click is heard If the PAPER INK RIBBON indicator illuminates when the door is closed the print paper may have not been installed correctly In this case open the door to make sure that the print paper has been installed correctly Then close the door again On the auto feed amp cut mode when the print paper is installed more than three times the print paper may be used up earlier than the ink ribbon vo HE When the manual amp cut mode has been selected When the manual feed amp
30. transporting this unit make sure it is not likely to be subjected to impacts They can be a prime cause for damage Further make sure to disconnect the power cord from the power outlet and the cables from the connected devices 3 SAFETY PRECAUTIONS OTHER CAUTIONS e Do not pull out nor touch the print paper until printing is completed It may degrade the print quality or cause an error e Dust or other foreign matter adhering to the print paper or the ink cassette or deformation resulting from exposure to extremely low or high temperatures could cause loss of color uneven color or lines or wrinkles in the print images SNOILNVOAUd e During printing on 15x23 6x9 size paper the printer may stop printing temporarily for cooling down The COOLING indicator blinks Please wait for the printer to resume printing after its completion of cooling Do not touch the print paper e During printing the printer may stop printing for about 90 seconds for cooling down The COOLING indicator blinks Please wait for the printer to resume printing after its completion of cooling e Each time printing on 13x18 5x7 size or 15x23 6x9 size paper is completed remove the prints If the prints are not removed a paper jam may occur NOTE YOUR UNDERSTANDING IS REQUESTED FOR THE LOSS OF IMAGES IN MEMORY DUE TO THE SUDDEN OCCURRENCE OF A MALFUNCTION n gt C JJ m V O O lt lt m O lt V JJ m gt
Download Pdf Manuals
Related Search