Gefen 4x4 Matrix for HDMI with FST and 3DTV
Contents
1. Binary 1 1 0011 0001 9 9 0110 1001 2 2 0011 0010 A 10 0110 0001 3 3 0011 0011 B 11 0110 0010 4 4 0011 0100 C 12 0110 0011 5 5 0011 0101 D 13 0110 0100 6 6 0011 0110 E 14 0110 0101 7 7 0011 0111 F 15 0110 0110 8 8 0011 1000 G 16 0110 0111 WALL MOUNTING INSTRUCTIONS The GefenToolBox 4x4 Matrix with FST should be mounted vertically in a wall or cabinet with wood drywall screws as shown in the diagram above There should be an inch or two of clearance between the edges of the unit and any walls or vertical surfaces to allow for enough clearance for insertion and retraction of cables at the HDMI connectors For installation on a drywall surface use a 6 drywall screw It is recommended when installing on a drywall surface that studs be used to secure the Matrix should undue stress be applied when connecting and disconnecting HDMI cables 21 Maximum Pixel Clock 225 MHz Maximum Video Resolution 1080p 1920x1200 60Hz with 12 bit Deep Color Input Video Signal 2V p p Input DDC Signal 5V p p TTL HDMI Connector type A 19 pin female 4 input 4 output LED Indicators sour2. supporting digital audio formats such as Dolby TrueHD and DTS HD Master Audio Each source is accessible at all times from any display by selecting it with the included IR remote the RS 232 port or using the front panel push buttons How It Works Connect the Hi Def A V sources to the GefenToolBox 4x4 Matrix s inputs using the supplied HDMI cable Connect up to 4 HDTV displays to the Matrix s four HDMI outputs using the provided HDMI cables 3D content can be displayed when connecting a 3DTV and 3D source Apply power to sources and to the displays A V Sources may now be routed to display devices by using the front panel buttons or the included IR remote control unit INTRODUCTION 1 READ THESE NOTES BEFORE INSTALLING OR OPERATING THE GEFENTOOLBOX 4X4 MATRIX WITH FST EDID contains the A V capabilities of a display device in regards to video resolutions and audio formats supported This information is used by the source device to determine the format of the A V signal on the outputs The GefenToolBox 4x4 Matrix with FST incorporates advanced EDID management to ensure compatibility with all sources and display devices Please see pages 14 18 for more details The GefenToolBox 4x4 Matrix with FST can detect the presence of Deep Color 12 bit signal automatically and will disable Deep Color EDID features across all other outputs if any f connected device or display is not capable of processing Deep Color This automatic b
3. 1 9 7 4 3 Side Panel 11 Front Panel 5 8 PANEL DESCRIPTIONS 1 HDMI Input Ports 1 4 Connect HDMI source devices to these ports 2 Fast Slow Switch Switches between Fast and Slow Switching See page 19 for more information 3 Audio Channel Selection Switch This switch will modify the EDID to specify the number of supported audio channels when using the INTERNAL EDID mode This setting will not affect the EDID information when using the EXTERNAL EDID mode 4 EDID Mode Selection Switch This switch will control the type of EDID used by the Matrix The options are EXTERNAL and INTERNAL See page 15 for details 5 Source Selectors 4 and Indicator LEDs 16 The four 4 black buttons labeled Out 1 Out 4 select input sources 1 4 to be mapped to the outputs 1 4 See pages 6 and 7 for more details on how to use these buttons 6 RS 232 Serial Port Connects to the RS 232 control device The 4x4 Matrix for HDMI may be switched remotely using this port See page 20 for details 7 IR Extender Port Connect an IR extender cable Gefen part no EXT RMT EXTIR to this port See page 13 for details 8 USB Service Port Mini USB service port used for upgrading the rmware 9 5V DC Locking Power Connector Connect the included 5V DC Locking Power Supply to this receptacle 10 Power Indicator This LED indicator will glow red when the unit is powered 11 IR Window Receives signals from the IR R
4. Gefen ASKING FOR ASSISTANCE Rev A3 Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday thru Friday Paci c Time Write To Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefentoolbox com support gefentoolbox com Notice Gefen LLC reserves the right to make changes in the hard ware packaging and any accompanying doc u men ta tion without prior written notice 4x4 Matrix for HDMI with FST is a trademark of Gefen LLC HDMI the logo and High De nition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing in the United States and other countries 2010 Gefen LLC All Rights Reserved All trademarks are the property of their respective owners CONTENTS 1 Introduction 2 Operation Notes 3 Features 4 Panel Layout 5 Panel Descriptions 6 Connecting And Operating The GefenToolBox 4x4 Matrix with FST 8 IR Remote Description 10 IR Remote Installation 11 IR Remote Con guration 12 Changing the IR Channel 13 IR Extender Installation 14 EDID Management 14 Understanding EDID 15 EDID Mode Selection 16 Audio Channel Selection 17 External EDID Management 18 Internal EDID Speci cation 19 FST Switching Technology 20 RS 232 Serial Control Interface 21 Wall Mounting Instructions 22 Speci cations 23 Warranty Congra
5. able below for setting the IR channel 3 Once the proper IR channel has been selected press and hold the Out 1 button for 5 seconds to con rm and exit IR channel selection mode The currently selected input source will now be indicated IR Channel Table Input LED IR Channel 1 0 2 1 3 2 4 3 12 13 Back of Cabinet Gefen Toolbox Unit Remote Set top Box IR EXTENDER INSTALLATION Using The IR Extender An optional IR Extender Gefen Part No EXT RMT EXTIR can be used to extend the IR capabilities of the GefenToolBox 4x4 Matrix with FST One such application allows the Matrix to be hidden within or behind a cabinet see illustration below Simply connect the IR extender to the IR extender port see page 4 IR Extender Understanding EDID The GefenToolBox 4x4 Matrix with FST features automatic and manual EDID adjustments to maximize compatibility of all attached devices First it is necessary to understand EDID and what it is used for EDID What is it and what is it used for Under normal circumstances source devices will require information about a connected display device to assess what video resolutions and other features are compatible with the output device This required information is called the EDID Extended Display Information Data Almost all types of output devices displays computer monitor HDTV A V receiver will transmit EDID to a connected source The source will then read
6. are a total of 16 buttons on the IR Remote Control unit Each set of colored buttons represents one of four Outputs on the Matrix The rst four buttons 1 4 represent Output 1 The second set of four buttons 5 8 represent Output 2 and so on Each numbered button within that set represents an input Buttons 1 4 represent Inputs 1 4 on Output 1 Buttons 5 8 represent Inputs 1 4 on Output 2 and so on IR REMOTE DESCRIPTION 8 1 2 RMT 16IR Remote Control Unit 9 IR REMOTE DESCRIPTION Example 1 Route the source connected to In 3 to the display connected to Out 4 1 Press button 15 Input 3 on the IR remote control unit The source connected to In 3 will be routed to the monitor connected to Out 4 Use the table below when selecting the desired source for each display Table of IR Remote Commands for the GefenToolBox 4x4 Matrix with FST RMT 16IR button Source Display 11 3 3 10 IR REMOTE INSTALLATION Installing the IR Remote Control Battery 1 Remove the battery cover on the back of the IR Remote Control unit 2 Insert the included battery into the open battery slot The positive side of the battery should be facing up 3 Replace the battery cover The Remote Control unit ships with two batteries One battery is required for operation and the other battery is a spare Battery Slot Resolving IR Code Con icts In the event that IR commands from other remote control
7. ce mapping 16 blue LED Indicator power 1 red RS 232 Interface DB9 serial F IR Extender 3 5 mm Mini Stereo Power Supply 5V DC Power Consumption 20W max Operating Temperature 0 40 C Dimensions 6 5 W x 11 75 H x 1 D Shipping Weight 6 lbs SPECIFICATIONS 22 WARRANTY 23 Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is noti ed within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modi cations Equipment that fails under conditions other than those covered
8. e Rev A3 Pb This product uses UL listed power supplies
9. ehavior ensures compatibility among all output devices in a mixed device environment This feature cannot be disabled When powering the GefenToolBox 4x4 Matrix with FST or if the EDID Mode is changed see pages 4 5 the Matrix will undergo a momentary initialization sequence This is normal operation and may take a few seconds OPERATION NOTES 2 FEATURES 3 Supported HDMI 1 3 Features 225 MHz up to 12 bit YUV 444 1080p Deep Color Dolby TrueHD and DTS HD Master Audio Lip Sync General Features Displays any of four 4 Hi Def sources on any four 4 HDTV displays independently Maintains beautiful sharp HDTV resolutions up to 1080p and 2K Supports 3DTV pass through EDID Management for rapid integration of sources and display devices Fast Switching for quick and responsive HDMI signal routing See page 19 for details Supports digital audio formats including LPCM 7 1 audio Dolby Digital Plus Dolby TrueHD and DTS HD Master Audio Built in IR Extender IR Remote Control RS 232 serial control Locking HDMI connections Firmware eld upgradable Wall mountable This product is HDCP compliant Package Includes 1 GefenToolBox 4x4 Matrix with FST 4 6 foot Locking HDMI cable M M 1 5V DC Locking Power Supply 1 IR remote control 1 User Manual PANEL LAYOUT 10 6 4 2 12
10. emote Control unit 12 HDMI Output Ports 1 4 Connect HDTV displays to these ports 5 6 How to Connect the GefenToolBox 4x4 Matrix with FST 1 Use one of the provided HDMI cables to connect the source device to the HDMI input port of the GefenToolBox 4x4 Matrix with FST 2 Use additional HDMI cables to connect up to 4 HDMI cables to the four 4 displays 3 Connect the included 5V DC locking power supply to the power receptacle on the Matrix 4 Connect the other end of the power supply to an available power outlet How to Operate the GefenToolBox 4x4 Matrix with FST The top panel of the GefenToolBox 4x4 Matrix with FST contains a set of LED indicators displaying which input source is routed to which output display This allows for easy management and viewing of all input and output routing states There are four 4 rows of LED indicators on the front panel To the left of the LED indicators are four push buttons Out 1 Out 2 Out 3 and Out 4 The numbers along the top of the LED matrix represent the currently selected Input source 1 2 3 or 4 Example 1 Routing Input source 2 to Output display 3 1 Ensure that an HDMI cable is connected from the source to HDMI In 2 and an HDMI cable is connected from the display to HDMI Out 3 on the Matrix 2 Press Out 3 Button on the row of black buttons running vertically until the LED under Input 2 is bright blue If the LED does not immediately appear unde
11. mation about the output devices that are connected to it thus ensuring compatibility EDID MANAGEMENT 14 15 EDID MANAGEMENT EDID Mode Selection EXTERNAL MODE To use this mode set the EDID Mode Switch on the front panel to the EXT position In External EDID mode the Matrix retrieves EDID data directly from each connected A V display device The EDID data is then compiled and a new EDID is created based on the highest supported video resolution and audio capabilities common to all displays The new EDID is sent back to the source device If insuf cient EDID data is available from external display devices or EDID related problems are encountered Internal EDID Mode should be used to provide a single compatible EDID for all connected devices INTERNAL MODE Internal EDID mode uses a preset EDID that is stored in the GefenToolBox 4x4 Matrix with FST from the factory To use this mode set the EDID Mode Switch on the front panel to the INT position All resolutions and audio formats speci ed in this EDID will be passed to the source device Many common resolutions and audio formats are supported For a complete listing of the resolutions and audio formats listed in this EDID please see page 18 NOTE All other HDMI capable devices displays connected to the output ports MUST be compatible with at least one resolution audio format speci ed in this EDID It is recommended to set on the source device a common re
12. r Input 2 continue depressing the Out 3 button until the LED under Input 2 turns bright blue Fig 1 1 Fig 1 1 CONNECTING AND OPERATING THE GEFENTOOLBOX 4X4 MATRIX FOR HDMI WITH FST 3 Once the LED under Input 2 turns bright blue a picture will be displayed on the display connected to Out 3 on the Matrix Note that in Fig 1 1 Out 1 Out 2 and Out 4 have also been routed In this case the displays connected to HDMI Out 1 HDMI Out 2 and HDMI Out 3 are receiving video from the source connected to HDMI In 1 Example 2 Routing Input source 3 to Output display 1 Using Fig 1 1 as a starting point press the Out 1 button two 2 times The LED matrix should now appear as follows Fig 1 2 LED 3 turns bright blue on the row labeled Out 1 indicating that Output display 1 is connected to the source on HDMI In 3 In Fig 1 2 the current state of the matrix is Display 1 is connected to HDMI 2 Display 2 is connected to Source 1 Display 2 is connected to Source 2 and Display 4 is connected to Source 1 Note that both Display 2 and Display 4 are connected to the same source CONNECTING AND OPERATING THE GEFENTOOLBOX 4X4 MATRIX FOR HDMI WITH FST 7 1 LED Button Press Indicator This LED will be activated momentarily each time a button is pressed 2 Display and Source Selection Buttons These buttons are used to select which source is routed to a monitor Routing Sources using the Remote Control unit g g There
13. s con ict with the supplied IR remote control unit changing the remote channel will alleviate this issue The IR remote control unit has a bank of DIP switches for setting the remote IR channel The DIP Switch bank on the IR remote control unit is located underneath the battery cover IR REMOTE CONFIGURATION It is important that the IR channel selected on the remote match the IR channel on the GefenToolBox 4x4 Matrix with FST for proper operation For example if you set both DIP switches on the remote to the down position toward the 1 and 2 IR channel 0 you must set the GefenToolBox 4x4 Matrix with FST to use IR channel 0 11 1 2 1 2 1 2 1 2 Remote Channel 2 Remote Channel 0 Default Remote Channel 1 Remote Channel 3 DIP Switches See page 12 for information on how to change the IR channel on the GefenToolBox 4x4 Matrix with FST CHANGING THE IR CHANNEL Setting The IR Channel on the Matrix Use the following procedure to set the proper IR channel on the Matrix 1 Press and hold the Out 1 button for 5 seconds to enter the IR channel selection mode The bank of blue LED indicators will now display the currently selected IR channel 2 Press the Out 1 button to cycle through each IR channel The currently selected IR channel will by indicated by a ashing blue LED IMPORTANT The selected IR channel must be the same as the IR channel set on the IR Remote see page 11 Refer to the t
14. solution and audio format shared by all attached devices displays This is to ensure a compatible signal is outputted to all connected devices displays 16 EDID MANAGEMENT Audio Channel Selection The GefenToolBox 4x4 Matrix with FST features a switch that will modify the supported audio formats listed in the pre programmed EDID This feature is useful for limiting the output of the source device to either 2 or multi channel audio formats NOTE This selector switch will only affect the pre programmed EDID in the INTERNAL INT EDID Mode The GefenToolBox 4x4 Matrix with FST can use either of the following settings for audio format support 2 Channel This setting will limit the audio formats listed in the pre programmed EDID to 2 channel LPCM For a full listing of the audio formats in this mode please see page 18 To use this mode set the Audio Selection Switch on the front panel to the 2 CH position H This mode is useful in scenarios where all output devices displays are HDTV monitors that only support 2 channel LPCM This setting will ensure that all connected devices will receive and produce sound Multi Channel This setting will enable all common audio formats in the pre programmed EDID For a full listing of the audio formats in this mode please see page 18 To use this mode set the Audio Selection Switch on the front panel to the Multi CH position H This mode is useful in scenarios where the output de
15. support Deep Color EDID MANAGEMENT 18 EDID MANAGEMENT Internal EDID Speci cations The table below lists the settings that comprise the built in Internal EDID data structure Video Data Block Audio Data Block Speaker Allocation xvYCC 1080p 60Hz 1080p 50Hz 1080i 60Hz native 1080i 50Hz 2 channel LPCM 2CH Multi channel LPCM 2CH LPCM 8CH AC 3 6CH DTS 7CH Dolby Digital 8CH Dolby TrueHD 8CH DTS HD 8CH MAT MLP 8CH 2 channel FL FR Multi Channel RLC RRC RL RR FC LFE FL FR xvYCC 709 xvYCC 601 FAST SWITCHING TECHNOLOGY 19 Fast Switching Technology Fast Switching Technology FST is a Gefen software implementation for HDMI 1 3 products FST was created to improve the inherited lengthy HDMI authentication process based on the HDMI and HDCP speci cations FST provides quicker A V source switching and greatly improves the overall A V system behavior and performance when more than one HDTV display is used in the system setup FST allows connecting disconnecting or turning ON OFF of HDTV displays without having these activities affect other Hi Def sources routed to any other HDTV display in the same system FAST MODE Setting the Matrix to FAST mode will improve performance when routing sources powering ON OFF HDTV displays and disconnecting connecting Hi Def sources NOTE When switching from SLOW mode to FAST mode the HDTV displays connected to the Matrix
16. this EDID le and make the necessary adjustments to the output signal to ensure that only compatible resolutions features are generated in the output signal Why is EDID so important with the GefenToolBox 4x4 Matrix with FST y p The GefenToolBox 4x4 Matrix with FST uses complex technology that routes multiple input signals to multiple outputs The source devices will require EDID to read Multiple devices displays can be connected to the input and output ports on the Matrix each with their own EDID Management of EDID is key to ensure that maximum compatibility is maintained between all devices What options do I have to manage the EDID in the GefenToolBox 4x4 Matrix p g with FST It is important to understand that the EDID contains much more than just listings of supported video resolutions and audio formats However resolutions and audio formats are the two key types of information that a user will need to understand how to use these EDID management functions Common problems that a user may encounter while using the Matrix can be 1 Video may not be visible on all output devices displays 2 Audio may not be heard on all output devices displays These symptoms usually arise from video resolution audio format incompatibilities between the devices displays connected to the outputs The GefenToolBox 4x4 Matrix with FST can use one of two methods to acquire and retransmit an EDID to the A V source device relaying infor
17. tulations on your purchase of the GefenToolBox 4x4 Matrix with FST Your complete satisfaction is very important to us About Gefen We specialize in total integration for your home theater while also focusing on going above and beyond customer expectations to ensure you get the most from your hardware We invite you to explore our distinct product line Please visit http www gefen com for the latest offerings in High De nition signal solutions or call us between the hours of 8 00 am and 5 00 pm Monday Friday Paci c Standard Time for assistance with your A V needs We ll be happy to assist you Why GefenToolBox The GefenToolbox line offers portable and easy to install solutions for common A V system integration setups using HDMI connectivity GefenToolBox products are wall mountable and small in size GefenToolBox products are easily transported in the eld and are ready for immediate and simple installations in working environments These products come nished in a glossy color to blend in with either a white wall or black cabinet The GefenToolBox 4x4 Matrix with FST The GefenToolBox 4x4 Matrix with FST routes HDMI at resolutions up to 1080p Full HD and 1920x1200 60Hz supporting multichannel digital audio from any four Hi Def sources to any four HDTV displays The GefenToolBox 4x4 Matrix eliminates the need to disconnect and reconnect HDMI sources It works with any HDMI source that needs to be connected to an HDTV display
18. vices displays are varying devices i e HDTV display and audio receivers Please note that sound may not be heard from all output devices displays if a shared common audio format is not used by the source device 17 External EDID Management The GefenToolBox 4x4 Matrix with FST features EDID Management Before the source can send video or audio signals to the display the source devices reads the EDID Extended Display Identi cation Data of each device connected to an output The EDID contains information about what type of AV data that the source can send to each display The GefenToolBox 4x4 Matrix with FST routes multiple source signals to multiple output devices This involves reading EDID data from more than one device Management of the EDID data is important to maintain compatibility between all devices Display Connections If a display is not connected to Output 1 then no EDID changes are made meaning that the previous EDID information will be used This state will be in effect until a display is connected to Output 1 and the Matrix is power cycled EDID is copied from Output 1 to all other outputs The audio block will be copied from Output 1 EDID copying is performed only when the Matrix is reset or power cycled 3DTV Support 3D signals are supported if a 3DTV is connected to Output 1 Deep Color Deep Color will be disabled if one of more other displays connected to the d Matrix do not
19. will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or tness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen 3 Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and speci cations is subject to change without notice For the latest warranty coverage information refer to the Warranty and Return Policy under the Support section of the Gefen Web site at www gefen com PRODUCT REGISTRATION Please register your product online by visiting the Register Product page under the Support section of the Gefen Web sit
20. will blink momentarily SLOW MODE When set to SLOW mode the Matrix will follow the standard authentication process based on the HDMI and HDCP speci cations SLOW mode is recommended when the source s does not support multiple devices FAST SWITCHING TECHNOLOGY 5 4 3 2 1 9 8 7 6 1 2 3 4 5 6 7 8 9 Only Pins 2 RX 3 TX and 5 Ground are used on the RS 232 serial interface This feature allows for easy integration into automated systems capable of transmitting RS 232 commands Use the settings below to con gure the RS 232 port of the user s system Transmitting the appropriate numeric ASCII character will simulate key presses on the IR remote control RS 232 Settings Bits per second 19200 Data bits 8 Parity None Stop bits 1 Flow Control None RS 232 SERIAL CONTROL INTERFACE 20 Binary Table ASCII Corresponding RMT 16IR Button Binary ASCII Corresponding RMT 16IR Button
Download Pdf Manuals
Related Search