Home

Samsung PN43D450A2D

1. i warm1 or Warm will be deactivated when the picture mode is Dynamic or Standard Settings can be adjusted and stored for each external device connected to an input on the TV Size If you have a cable box or satellite receiver it may have its own set of Screen sizes as well However we highly recommend you use 16 9 mode most of the time 16 9 Sets the picture to 16 9 wide mode Zoom1 Use for moderate magnification Cuts off the top and sides Zoom2 Use for a stronger magnification Wide Fit Enlarges the aspect ratio of the picture so it fits the entire screen 9X Available with HD 10801 720p signals in 16 9 mode 16 Engish 4 8 Sets the picture to basic 4 3 mode i Do not set your TV to 4 3 format for a long time The borders displayed on the left and right or top and bottom of the screen may cause image retention screen burn which are not covered by the warranty Screen Fit When your TV inputs HDMI 720p 1080i 1080p or Component 1080i 1080p signals displays the full image without any cut off NOTE To use the Position function after selecting Zoom1 Zoom or Wide Fit follow these steps 1 Press the 9 button to select Position 2 Press the ENTER C button 3 Pressthe A or V button to move the picture up or down 4 Press the ENTERCS button 5 Press the P button to select Reset 6 Press the ENTER C button to reset the picture to its defau
2. o The TV Signal Strength is unavailable in the Self Diagnostic Test menu This function is only available with digital channels from an Antenna RF Coax connection p 22 The TV is tilted to the side o Remove the base stand from the TV and reassemble it The channel menu is greyed out unavailable The Channel menu is only available when the TV source is selected Your settings are lost after 30 minutes or every time the TV is turned off If the TV is in the Store Demo mode it will reset audio and picture settings every 30 minutes Change the settings from Store Demo mode to Home Use mode in the Plug amp Play procedure Press the SOURCE button to select TV mode and go to MENU Setup Plug amp Play ENTERS p 8 You have intermittent loss of audio or video Check the cable connections and reconnect them Loss of audio or video can be caused by using overly rigid or thick cables Make sure the cables are flexible enough for long term use If mounting the TV to a wall we recommend using cables with 90 degree connectors You see small particles when you look closely at the edge of the frame of the TV This is part of the product s design and is not a defect POP TV s internal banner ad appears on the screen Select Home Use under Plug amp Play mode For details refer to Plug amp Play Feature p 8 i Some of above pictures and functions are
3. Picture Reset Reset Picture Mode Cancel Resets your current picture mode to its default settings i Changing the Preset Sound Mode MENU II Sound Mode ENTERC Select an option using the up and down arrow keys and the press ENTER Mode Use the up and down arrow keys to select an option and then press ENTER W Standard Selects the normal sound mode Music Emphasizes music over voices B W Movie Provides the best sound for movies E Clear Voice Emphasizes voices over other sounds L Custom Increase the intensity of high frequency sound to allow a better listening experience for the hearing impaired il Adjusting Sound Settings MENU I Sound Equalizer gt ENTERC The Equalizer displays a series of sliders Use the up and down arrow keys to select a slider Use the left and right arrow keys to change the slider s value To Reset the Equalizer select Reset and press ENTER then press ENTER again To exit select CLOSE and then press ENTER Equalizer Adjusts the sound output E Balance L R Adjusts the balance between the right and left speaker B 100Hz 300Hz 1kHz 3kHz 10kHz Bandwidth Adjustment Adjusts the volume level of specific bandwidth frequencies WB Reset Resets the equalizer to its default settings D Sound Settings MENU I Sound ENTER C SRS TruSurround HD Off On This function provides a virtual 5 1 channel surround
4. H Picture Test Yes No Use to check for picture problems Picture test displays a high definition picture that you can examine for flaws or faults Yes Select Yes If the test picture does not appear or there is noise or distortion in the test picture select Yes There may be a problem with the TV Contact Samsung s Call Center for assistance No Select No if the test picture displays properly There may be a problem with your external equipment Please check your connections If the problem persists refer to the external device s user manual 22 Engish E Sound Test Yes No Use the built in melody sound to check for sound problems 8 qr you hear no sound from the TV s speakers before performing the sound test make sure Speaker Select is set to TV Speaker in the Sound menu and then try the speakers again You will hear the melody during the test even if you have set Speaker Select is set to External Speaker or have muted the sound by pressing the MUTE button Yes Select Yes if you can hear sound from only from one speaker or from neither speaker during the sound test select Yes There may be a problem with the TV Contact Samsung s Call Center for assistance 1 800 SAMSUNG No Select No if you can hear sound from the speakers select No There may be a problem with your external equipment Please check your connections If the problem persists refer to the external device s user manual W Signal Stre
5. 2011 Samsung Electronics America Inc ng installation of your TV Not responsible for typographical or printed errors Engish 37 uoneuuoju Jeu O S0 Other Information A Antenna Anynet Auto Volume B Background Music Balance L R Batteries Black Tone Blanking Bracket Brightness C Change PIN Channel Menu Clock Color Tone Component Connecting to a PC Connecting to an Audio Device D DIGITAL AUDIO OUT Dynamic Dynamic Contrast E Eco Sensor Edit Name Editing Channels Energy Saving Equalizer External Speaker 38 English 18 26 18 26 17 15 30 15 20 13 18 16 9 11 10 27 15 15 21 12 14 21 17 18 F Film Mode Fine Tune Flesh Tone Frequency H HDMI Home Theater Installation Space L Language License M Media Play Melody Mono Music N Navigate O Optimal resolution P Photo Picture Size Plug amp Play Power Indicator 17 15 16 11 26 31 21 36 23 22 18 25 12 11 24 oco R Receiver Recording Remote Control Repeat Music S Select All Self Diagnosis Sharpness Sleep Timer Slide Show Software Upgrade Source List Speaker Select Specifications Standby mode Symbol T Timer Tools Troubleshooting TV Speaker U USB Drive V Volume W Wall Mount Warm White Balance 22 28 28 25 14 22 15 19 24 22 12 18 36 19 33 18 23 30 16 16
6. 480i 1080i W Screen Burn Protection To reduce the possibility of screen burn this unit is equipped with screen burn prevention technology The Time setting allows you to program the time between movement of the picture in minutes Pixel Shift Off On Using this function you can minutely move pixels on the PDP in horizontal or vertical direction to minimize after images on the screen amp Optimum condition for pixel shift item TV AV Component HDMI PC Horizontal 0 4 4 Vertical 0 4 4 Time minute 1 4 min 4 min The Pixel Shift value may differ depending on the TV size inches and mode This function is not available in the Screen Fit mode Scrolling This function removes after images on the screen by moving all the pixels on the PDP according to a pattern Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time The after image removal function has to be executed for a long time approximately 1 hour to effectively remove after images on the screen If the after image is not removed after performing the function repeat the function again Press any key on the remote control to cancel this feature Side Gray Dark Light When you watch TV with the Screen ratio set to 4 3 the screen is prevented from any damage by adjusting the white balance on both extreme left and right sides
7. depending on the downloaded information Canadian English You can block TV programs depending on their Anglophone Canadian ratings C Programming intended for children under age 8 C8 Programming generally considered acceptable for children 8 years and over to watch on their own G General programming suitable for all audiences PG Parental Guidance 14 Programming contains themes or content which may not be Even if you set the on screen display to another suitable for viewers under the age of 14 18 Adult language the Downloadable U S Rating programming menu will appear in English only The V Chip will automatically block any category The rating will automatically block certain that deals with more sensitive material For categories that deal with more sensitive example if you block the G category then material PG 14 and 18 will automatically be blocked The rating titles For example Humor Level etc Canadian French You can block TV programs and TV ratings For example DH MH H etc depending on their Anglophone Canadian ratings may differ depending on the broadcasting G General 8 ans Programming generally station considered acceptable for children 8 years and over WI Change PIN The Change PIN screen will appear to watch on their own 13 ans Programming may Choose any 4 digits for your PIN and enter them As not be suitable for children under the age of 1 3 soon as the 4 dig
8. INFO button during the photo view to set the following options Start Slide Show Zoom Rotate List Press the A or V button to select the option then press the ENTERC button After setting the option press the ENTER C button to make a change 24 English Music Using the MP3 List re Folder icon Music 1 SUM d Music list icon N 307 2MB 973 7MB f Move to the previous folder stage icon wou i Press the REW or gt gt FF buttons to change pages Wee A 9i The selected file is displayed on the top with its playing time 4 gt Move C Enter 5 Retum 1 To select all files or a file press the INFO button to display the Music menus Press the ENTER C button to select Play or Play the Selected Files Repeat Music Delete or Delete Selected File Delete All or RE Deselect All i e 2 Press the A or V button to move to an icon then press the Repeat Music Ee m ENTER C button Delete Selected File hils omas Pressing the ENTER C button over a musical note icon immediately du res 25 plays the music file PEK PETER E Pressing the ENTER C button over a folder icon shows the music duck M Mis files included in the folder W Play Select to play MP3 files This menu only shows files with the MP3 file extension Files with other file extensions are not displayed even if they are saved on the same USB device A To adjust the music volume press the VOL button o
9. Menu tren 15 Storage and Maintenance 35 Changing the Preset Picture Mode 15 LENS e aE E E E E TE A E E E 36 Adjusting Picture Settings 15 Specifications sssini 36 By Changing the Picture Options 15 e Dimensions 37 e Sound Menu 17 e Index iss 38 E Changing the Preset Sound Mode 17 Adjusting Sound Settings 17 Sound Settings 17 Check the Symbol W This function can be used by pressing the Note Step by Step Guide TOOLS button on the remote control Indicates additional information Check here for instructions on how to open the relevant submenu within the OSD on screen display English 3 Getting Started e Excellent Digital Interface amp Networking With a built in HD digital tuner nonsubscription HD broadcasts can be viewed without a cable box STB Set Top Box satellite receiver e SRS TruSurround HD provides a virtual surround system p 17 Media Play Allows you to play music files pictures saved on a USB device p 23 Self Diagnosis You can check to make sure picture and sound operate normally p 22 Accessories Please make sure the following items are included with your PDP TV If any items are missing contact your dealer 9i The items colors and shapes may vary depending on the model Check that there is no accessory hidden behind packing materials when you open the box e Remote Control AA59 00506A amp Batteries AAA x 2 Power Cord Owners Instructions e Cleaning Cl
10. On the Channel List you can view Added Channels channel information and Favorites and manage channels MENU I Channel Channel List ENTER Select a channel in the All Channels Added Channels Favorite or Programmed screen by pressing the A V and ENTER Cs buttons Then you can watch the Selected channel Air Y TV 9 6 S euueut Peppy mZoom W Ee X Tools All Channels Shows all currently available channels JH Added Channels Shows all added channels E E Wi 99 Favorite Shows all favorite channels Programmed Shows all currently reserved programs Using the color buttons with the Channel List E Green Zoom Enlarges or shrinks a channel number m Yellow Select Selects multiple channel lists Select desired channels and press the Yellow button to set all the selected channels at the same time The v mark appears to the left of the selected channels X1 Tools Displays the Channel List option menu The options menus may differ depending on the situation Channel Status Display Icons Icons Description A A channel selected v A channel set as a Favorite Q A reserved Program I Using Favorite Channels MENU I Channel Channel List ENTER C Add to Favorite Delete from Favorite Tag channels you watch frequently as Favorites 1 Select a channel and press the TOOLS button 2 Add or delete a the channel usi
11. VIDEO OUT AUDIO OUT Device AUDIO OUT COMPONENT OUT evice j C w R AUDIO L R AUDIO L Pr Ps G When connecting to AV IN the color of the AV IN Y VIDEO jack green will not match the video cable yellow i For better picture quality the Component connection is recommended over the A V connection English 9 Suonoeuuo ZO Connections Using an Optical Digital Cable Connection Available devices Digital Audio System Amplifier DVD home theater Digital Audio System OPTICAL OPTICAL 3 Optical Cable Not Supplied DIGITAL AUDIO OUT OPTICAL DIGITAL AUDIO OUT OPTICAL When you connect a Digital Audio System to the DIGITAL AUDIO OUT OPTICAL jack decrease the volume of both the TV and the system 5 1 CH channel audio is available when you connect the TV to an external device supporting 5 1 CH When the receiver amplifier or DVD home theater is set to on you can hear sound output from the TV s optical jack When the TV is receiving a DTV signal the TV will send 5 1 CH sound to the amplifier or DVD home theater When the source is a digital component such as a DVD player Blu ray player cable box STB Set Top Box satellite receiver and you connection it to the TV via HDMI you will only 2 CH audio from the amplifier or DVD home theater If you want to hear 5 1 CH audio connect the digital audio out jack from your DVD Bl
12. When the source is a digital component such as a DVD and is connected to the TV via HDMI you will hear only 2 channel sound from the receiver NOTE You can only control Anynet devices using the TV remote control not the buttons on the TV The TV remote control may not work under certain conditions If this occurs reselect the Anynet device The Anynet functions do not operate with other manufacturers products 28 Engish li Troubleshooting for Anynet Problem Possible Solution Anynet does not work e Check if the device is an Anynet device The Anynet system supports Anynet devices only Only one receiver home theater can be connected e Check if the Anynet device power cord is properly connected e Check the Anynet device s Video Audio HDMI cable connections Check whether Anynet HDMI CEC is set to On in the Anynet setup menu e Check whether the TV remote control is in TV mode Check whether the remote control is Anynet compatible e Anynet doesn t work in certain situations Searching channels operating Media Play USB or Plug amp Play initial setup etc e When connecting or removing the HDMI cable please make sure to search devices again or turn your TV off and on again e Check if the Anynet Function of Anynet device is set on want to start Anynet e Check if the Anynet device is properly connected to the TV and check if the Anynet HDMI CEC is set to On
13. blocked English 19 sounyee4 oiseg g0 Basic Features MPAA Rating You can block movies depending on Downloadable U S Rating Parental restriction their MPAA rating The Motion Picture Association of information can be used while watching DTV channels America MPAA has implemented a rating system that NOTE provides parents or guardians with advanced information If information is not downloaded from the on which films are appropriate for children broadcasting station the G General audience no restrictions PG Parental Downloadable U S Rating menu is guidance suggested PG 13 Parents strongly deactivated cautioned R Restricted Children under 17 should be accompanied by an adult NC 17 No children under age 17 X Adults only NR Not rated The V Chip will automatically block any category Parental restriction information is automatically downloaded while watching DTV channels It may take several seconds that deals with more sensitive material For The Downloadable U S Rating mend example if you block the PG 13 category then R is available for use after information is l NC 17 and X will automatically be blocked downloaded from the broadcasting station However depending on the information from the broadcasting station it may not be available for use Parental restriction levels differ depending on the broadcasting station The default menu name and Downloadable U S Rating change
14. designated for your TV 9i Make sure to use only the appropriate supplied screw If you use a different screw you can damage your TV 2 Firmly fasten the screw you provided size M4xL20 or similar to the wall or cabinet where the TV is to be installed 83 f you fasten the screw to the wall we recommend you drive the screw into a stud If that is not possible use a molly to anchor the screw 3 Tie the TV Holder cord to the screw fastened on the wall or cabinet so that the TV is fixed See the illustrations below nstall the TV close to the wall so that it does not fall When attaching the TV Holder cord to the wall tie the cord level with the ground or slanted downwards for safety purposes Check the cord occasionally to make sure it is secure Before moving the TV separate the connected cord first OOOO 4 Verify all connections are properly secured Periodically check the connections for any sign of fatigue or failure If you have any doubt about the security of your connections contact a professional installer To purchase the TV Holder Kit contact Samsung Customer Care n the United States 1 800 SAMSUNG 1 800 726 7864 n Canada 1 800 SAMSUNG 1 800 726 7864 3 2 English Troubleshooting If the TV seems to have a problem first try this list of possible problems and solutions Also review the Troublehsooting section in the e Manual If none of the troubleshooting tips apply
15. image is clear amp Settings are applied to the channel you re currently watching i Fine tuned channels that have been saved are marked with an asterisk on the right hand side of the channel number in the channel banner i To reset the fine tuning select Reset Changing the Preset Picture Mode MENU II Picture Mode ENTERC Mode Select your preferred picture type W Dynamic Suitable for a bright room W Standard Suitable for a normal environment W Movie Suitable for watching movies in a dark room E Adjusting Picture Settings MENU II Picture gt ENTER Cell Light Contrast Brightness Sharpness Color Tint G R Your television has several options for adjusting picture quality Select an option using the up and down arrow keys and then press ENTER Use the arrow keys to adjust the option value or select an option setting When done press ENTER NOTE When you make changes to Cell Light Contrast Brightness Sharpness Color or Tint G R the OSD will be adjusted accordingly Settings can be adjusted and stored for each external device connected to the TV You can adjust and store Settings for each external device connected to the TV i Changing the Picture Options Advanced Settings MENU I Picture Advanced Settings gt ENTER C All Advance Settings are available in the Standard and Movie modes In PC mode you can only make chang
16. in the Anynet Setup menu e Press the TOOLS button to display the Anynet menu and select a menu you want want to exit Anynet e Select View TV in the Anynet menu e Press the SOURCE button on the TV remote control and select a non Anynet device e Press WV CH A PRE CH to change the TV mode Note that the channel button operates only when a tuner embedded Anynet device is not connected The message Connecting to You cannot use the remote control when you are configuring Anynet or switching to a view mode Anynet device appears onthe Use the remote control after the TV is done Anynet configuring or switching to Anynet Screen The Anynet device does not play You cannot use the play function when Plug amp Play initial setup is in progress The connected device is not e Check whether or not the device supports Anynet functions displayed e Check whether or not the HDMI cable is properly connected Check whether Anynet HDMI CEC is set to On in the Anynet setup menu e Search Anynet devices again You can connect an Anynet device using an HDMI cable only Some HDMI cables may not support Anynet functions If connection is terminated because there has been a power interruption or the HDMI cable has been disconnected please repeat the device scan The TV Program cannot be recorded Check whether the antenna jack on the recording device is properly connected The TV sound is not output
17. the Speaker Select option to TV Speaker in the Sound menu p 18 If you are using an external device make sure the audio cables are connected to the correct audio input jacks on the TV If you are using an external device check the device s audio output option ex you may need to change your cable box s audio option to HDMI when you have a HDMI connected to your TV If you are using a DVI to HDMI cable a separate audio cable is required If your TV has a headphone jack make sure there is nothing plugged into it Reboot the connected device by reconnecting the device s power cable The speakers are making an inappropriate noise Check cable connections Make sure a video cable is not connected to an audio input For antenna or Cable connections check the signal strength Low signal level may cause sound distortion Perform the Sound Test as explained above English 33 uoneuuoju Jeu O S0 Other Information Issues Solutions and Explanations No Picture No Video The TV won t turn on Make sure the AC power cord is securely plugged in to the wall outlet and the TV Make sure the wall outlet is working Try pressing the POWER button on the TV to make sure the problem is not the remote If the TV turns on refer to Remote control does not work below The TV turns off automatically Ensure the Sleep Timer is set to Off in the Setup menu p 19 If your PC is connected to the TV check
18. visit www samsung com then click on Support or call Samsung customer service at 1 800 SAMSUNG Issues Solutions and Explanations Poor picture First of all please perform the Picture Test and confirm that your TV is properly displaying the test image go to MENU Support Self Diagnosis Picture Test p 22 If the test image is properly displayed the poor picture may be caused by the source or signal The TV image does not look as good as it did in the store If you have an analog cable satellite box upgrade to an HD digital set top box Use HDMI or Component cables to deliver HD high definition picture quality Cable Satellite subscribers Try HD stations from the channel line up Antenna connection Try HD stations after performing Auto program 9 Many HD channels are up scaled from SD Standard Definition contents Adjust the Cable Sat box video output resolution to 1080i or 720p The picture is distorted macro block error small block dots pixelization Compression of video contents may cause picture distortion especially in fast moving pictures such as sports and action movies Low signal level can cause picture distortion This is not a TV problem Mobile phones used close to the TV up to 3 3 ft may cause noise in picture on analog and digital TV Color is wrong or missing If you re using Component connection make sure the component cables are connected to the correct jacks
19. x 56 0 x 706 6 mm With stand 39 8 x 9 7 x 27 5 inches 46 8 x 9 7 x 30 8 inches 1011 8 x 245 7 x 698 7 mm 1187 8 x 245 7 x 782 9 mm Weight Without Stand 35 3 Ibs 16 0 kg 49 6 Ibs 22 5 kg With Stand 41 9 Ibs 19 0 kg 56 2 Ibs 25 5 kg Display Resolution 1024 X 768 1360 X 768 8 Design and specifications are subject to change without prior notice i This device is a Class B digital apparatus For information about the power supply and more about power consumption refer to the label attached to the product Dispose unwanted electronics through an approved recycler To find the nearest recycling location go to our website www samsung com recyclingdirect or call 877 278 0799 36 Engish E Front view Side view 9 m o e A Z ic EN Y I e l o Unit inches Model name o 2 e 4 5 6 7 3 PN43D440 PN43D450 39 8 37 6 21 6 20 1 24 5 27 5 2 2 9 7 PN51D440 PN51D450 46 8 44 6 25 0 20 1 27 8 30 8 2 2 9 7 W Jack panel detail Rear view Unit inches Model name 1 2 3 4 5 6 PN43D440 PN43D450 15 7 3 7 3 4 29 6 15 7 16 7 PN51D440 PN51D450 15 7 3 9 47 36 2 15 7 18 7 NOTE All drawings are not necessarily to scale Some dimensions are subject to change without prior notice Refer to the dimensions prior to performi
20. you want 4 Press the ENTER Cs button when done NOTE Only memorized channels can be reserved Reserved programs will be displayed in the Programmed menu When a digital channel is selected press the gt button to view the digital program W Select All Select all the channels in the channel list W Deselect All Deselect all the selected channels You can only select Deselect All when one or more channels are selected O Programmed in Channel List You can view modify or delete a show you have reserved to watch Programmed timer viewing is displayed here Highlight a program and press the TOOLS button to display options W Change Info Change a show you have reserved to watch Begin with step 3 of Timer Viewing above W Cancel Schedules Cancel a show you have reserved to watch 9X This deletes the highlighted or selected program s W Information Display a show you have reserved to watch You can also change the reservation Information Alternatively you can view Information by highlighting a program and pressing the ENTERC button W Select All Deselect All Select or deselect all reserved programs Fine Tune analog channels only If the reception is clear you do not have to fine tune the channel as this is done automatically during the search and store operation If the signal is weak or distorted fine tune the channel manually Scroll to the left or right until the
21. 024 x 768 56 476 70 069 75 000 Vv Vv 1024 x 768 60 023 75 029 78 750 Vv v 1280 x 720 45 000 60 000 74 250 Vv 1360 x 768 47 712 60 015 85 500 Vv VESA GTF 1280 x 720 52 500 70 000 89 040 Vv NOTE For HDMI DVI cable connection you must use the HDMI IN 1 DVI jack The interlace mode is not supported The set may operate abnormally if a non standard video format is selected Separate and Composite modes are supported SOG Sync On Green is not supported English 11 Changing the Input Source Source List Use to select TV or an external input sources such as a DVD player Blu ray player cable box STB satellite receiver MENU II Input Source List gt y ENTERC SOURCE E TV AV Componenti Component2 HDMI1 DVI HDMI2 i You can only choose external devices that are connected to the TV In Source connected inputs will be highlighted Basic Features Before using the TV follow the steps below to learn how to navigate the menu and select and adjust different functions MENU button Displays the main on screen menu ENTER CS Direction button Move the cursor and select an item Confirm the setting RETURN button Returns to the previous menu EXIT button Exits the on screen menu 12 Engish Edit Name MENU I Input Edit Name ENTER Cs In the Source press the TOOLS button and then you can set an external input
22. 18 P SIZE Lets you choose the picture size p 16 CC Controls the caption decoder p 21 Use the remote control within 23 feet from the TV Bright light may affect the performance of the remote control Avoid using when near fluorescent lights or neon The color and shape may vary depending on the model English 7 LO peueijs Dune5 Getting Started Connecting to an Antenna or Cable Connection When the TV is initially powered on basic settings proceed automatically Connecting the power cord and an antenna or cable connection yY The PDP device may interfere with an amateur radio or AM radio VHF UHF Antenna Antenna Cable Not Supplied Power Input Plug amp Play Initial Setup When you turn the TV on for the first time a sequence of on screen prompts will assist in configuring basic settings To turn on the TV Press the POWER 5 button Plug amp Play is available only when the Input source is set to TV Plug amp Play is available only when the Source is set to TV i To return to the previous step in the Plug amp Play sequence press the red button on your remote 1 Selecting the OSD Press the lt or gt button and then press the A or V button to Language select a language Press ENTER Cs when done POWER 2 Selecting Store Demo Press the lt or gt button then press the ENTER C button or Home Use Select the Home Use mode Store Demo mode
23. Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care center Country Customer Care Center T Web Site Address CANADA 1 800 SAMSUNG 726 7864 www samsung com ca Samsung Electronics Canada Inc Customer Service 55 Standish Court Mississauga Ontario L5R 4B2 Canada U S A 1 800 SAMSUNG 726 7864 www samsung com us Samsung Electronics America Inc 85 Challenger Road Ridgefield Park NJ 07660 2112 2011 Samsung Electronics Co Ltd All rights reserved BN68 03325A 01 imagine the possibilities Thank you for purchasing this Samsung product To receive more complete service please register your product at www samsung com register Mode Seria No Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance Product design and specifications may be changed without notice Important Warranty Information Regarding Television Format Viewing See the warranty card for more information on warranty terms Wide screen format PDP Displays 16 9 the aspect ratio of the screen width to height are primarily designed to view wide screen format full motion video The images displayed on them should primarily be in the wide screen 16 9 ratio format or expanded to fill the screen if your model offers this feature and the images are constantly moving Displaying statio
24. G is not responsible for any data file damage or data loss Please connect directly to the USB port of your TV If you are using a separate cable connection there may be a USB Compatibility problem English 23 Advanced Features Only MP3 and JPEG file formats are supported The Media Play USB mp3 format only supports music files with a high sampling frequency 32 kHz 44 1 kHz or 48 kHz We recommend the sequential jpeg format Do not disconnect the USB device while it is loading MSC supports MP3 and JPEG files and the PTP device supports JPEG files only MTP Media Transfer Protocol is not supported The playing duration of an mp3 file may be displayed as 00 00 00 if its playing time information is not found at the start of the file The higher the resolution of the image the longer it takes to display on the screen The Photo or Music List displays up to 300 folders or files Loading may take some time depending on the size of the file MP3 files with DRM that have been downloaded from a non free site cannot be played Digital Rights Management DRM is a technology that supports the creation distribution and management of the content in an integrated and comprehensive way including the protection of the rights and interests of the content providers the prevention of the illegal copying of contents as well as managing billings and settlements The power saving mode of some external hard disk drive
25. Incorrect or loose connections may cause color problems or a blank screen There is poor color or brightness Adjust the Picture options in the TV menu go to Picture mode Color Brightness Sharpness p 15 Adjust Energy Saving option in the Setup menu p 21 Try resetting the picture to view the default picture settings go to MENU Picture Picture Reset p 17 There is a dotted line on the edge of the Screen if the picture size is set to Screen Fit change it to 16 9 p 16 Change cable satellite box resolution The picture is black and white If you are using an AV composite input connect the video cable yellow to the Green jack of component input 1 on the TV When changing channels the picture freezes or is distorted or delayed f connected to a cable box please try to reset it reconnect the AC cord and wait until the cable box reboots It may take up to 20 minutes Set the output resolution of the cable box to 1080i or 720p Sound Problem First of all please perform the Sound Test to confirm that your TV audio is properly operating go to MENU Support Self Diagnosis Sound Test p 22 If the audio is OK the sound problem may caused by the source or signal There is no sound or the sound is too low at maximum volume Please check the volume of the device Cable Sat Box DVD Blu ray etc connected to your TV The picture is good but there is no sound Set
26. adcast station and signal the auto time set up may not be correct In this case set the time manually Clock Set Set the Month Day Year Hour Minute and am pm manually Select Clock Set Select Date or Time and then press ENTER Use the number buttons to enter numbers or press the up and down arrow buttons Use the left and right arrow buttons to move from one entry field to the next Press ENTER when done To exit Clock Set selet Close and press ENTER X Available only when Clock Mode is set to Manual You can set the Month Day Year Hour and Minute directly by pressing the number buttons on the remote control Time Zone Select your time zone This function is only available when the Clock Mode is set to Auto DST Daylight Saving Time Off On Auto Switches the DST Daylight Saving Time function on or off This function is only available when the Clock Mode is set to Auto D Using the Sleep Timer MENU II Setup Time Sleep Timer ENTER F W Sleep Timer Automatically shuts off the TV after a preset period of time 30 60 90 120 150 and 180 minutes i To cancel the Sleep Timer select Off E Setting the On Off Timer MENU II Setup gt Time Timer 1 gt ENTERC Set On Timer so that your TV turns on automatically at a time and on a day of your choosing W Timer 1 Timer 2 Timer 3 Three different on off imer settings can be made You must set the c
27. ased in Canada and in Canada on SAMSUNG products purchased in the United States for the warranty period originally specified and to the Original Purchaser only The above described warranty repairs must be performed by a SAMSUNG Authorized Service Center Along with this Statement the Original Limited Warranty Statement and a dated Bill of Sale as Proof of Purchase must be presented to the Service Center Transportation to and from the Service Center is the responsibility of the purchaser Conditions covered are limited only to manufacturing defects in material or workmanship and only those encountered in normal use of the product Excluded but not limited to are any originally specified provisions for in home or on site services minimum or maximum repair times exchanges or replacements accessories options upgrades or consumables For the location of a SAMSUNG Authorized Service Center please call toll free n the United States 1 800 SAMSUNG 1 800 726 7864 In Canada 1 800 SAMSUNG e Screen Image retention Do not display a still image such as on a video game on the plasma display panel for more than several minutes as it can cause screen image retention This image retention is also known as screen burn To avoid such image retention refer to page 15 of this manual to reduce the degree of brightness and contrast of the screen when displaying a still mage e Heat on the top of the Plasma TV The top side of the product may be hot a
28. available at specific models only B Storage and Maintenance Do not spray water or a cleaning agent directly onto the Clean the product with a soft cloth dampened with a small product Any liquid that goes into the product may causea amount of water failure fire or electric shock Engish 35 uoneuuoju JeuO S0 Other Information SfS 9 TruSurround HD SRS and symbol are trademarks of SRS Labs Inc TruSurround HD TruSurround HD technology is incorporated under license from SRS Labs Inc I DOLBY Manufactured under license from Dolby Laboratories Dolby and the double D symbol are DIGITAL PLUS trademarks of Dolby Laboratories Open Source License Notice In the case of using open source software Open Source Licenses are available on the product menu Open Source License Notice is written only English Specifications Environmental Considerations Operating Temperature 50 F to 104 F 10 C to 40 C Operating Humidity 10 to 80 non condensing Storage Temperature 4 F to 113 F 20 C to 45 C Storage Humidity 5 to 95 non condensing Stand Swivel Left Right o Model Name PN43D440 PN43D450 PN51D440 PN51D450 Screen Size 43 Class 51 Class Diagonal 43 0 measured diagonally 50 7 measured diagonally Sound Output 10WX2 10WX2 Dimensions WxDxH Body 39 8 x 2 2 x 24 5 inches 46 8 x 2 2 x 27 8 inches 1011 8 x 56 0 x 622 4 mm 1187 8
29. ay player HD cable box HD STB Set Top Box satellite receiver f Device HDMI Cable Not Supplied jr HDMI to DVI Cable Not Supplied phen E Red White Audio Cable Not Supplied 8b HDMI IN 1 DVI 2 DVI AUDIO IN When using an HDMI DVI cable connection you must use the HDMI IN 1 DVI jack for video A DVD player Blu ray player HD cable box or HD STB satellite receiver may require a DVI HDMI DVI to HDMI cable or DVI HDMI DVI to HDMI adapter You must use the PC DVI AUDIO IN jack for audio The DVI AUDIO IN jack is required for audio The picture may not display normally if at all or the audio may not work if an external device that uses an older version of HDMI mode to the TV If such a problem occurs ask the manufacturer of the external device about the HDMI version and if out of date request an upgrade Besure to purchase a certified HDMI cable Otherwise the picture may not display or a connection error may occur Using a Component up to 720p 1080i or an Audio Video 480i only Cable Available devices DVD player Blu ray player cable box STB satellite receiver VCR Red Blue ET Red White Yellow Video Cable Not Supplied Audio Cable Not Supplied E Component Cable Not Supplied 7 UD T iil em
30. crews M4 X L12 as shown Correct assembly Incorret assembly 2 With your TV upright connect the TV to the Stand 3 Fasten four screws M4 X L8 at position 8 NOTE Make sure to distinguish between the front and back of the Stand and Guide Stand when assembling them Make sure that at least two people lift and move the PDP TV AN Do not insert your fingers into the stand base slot of the TV when installing the stand base English 5 Getting Started Viewing the Control Panel The product color and shape may vary depending on the model Power Indicator Remote control sensor Samsune ZL Speakers Power Indicator Blinks and turns off when the power is on and lights up in standby mode Remote control sensor Aim the remote control towards this spot on the TV Power Turns the TV on or off SOURCE C Toggles between all the available input sources In the on screen menu use this button as you would use the ENTER C button on the remote control MENU CONTENT Displays an on screen menu the OSD on screen display of your TV s features VOL Adjusts the volume In the OSD use the VOL buttons as you would use the lt and gt buttons on the remote control V CHA Changes the channels In the OSD use the W CH A buttons as you would use the Y and A buttons on the remote control Standby mode Your TV enters Standby mode when you turn it off and continues to consume a s
31. eo contents may cause picture distortion especially with fast moving pictures such as sports and action movies A low signal can cause picture distortion This is not a TV problem PC Connection A Mode Not Supported message appears Set your PC s output resolution so it matches the resolutions supported by the TV p 11 The video is OK but there is no audio If you are using an HDMI connection check the audio output setting on your PC Others Purple green rolling horizontal bars and buzzing noise from the TV speakers with Component cable connection Remove the left and right audio connections from the set top box If the buzzing stops this indicates that the set top box has a grounding issue Replace the Component video cables with an HDMI connection The picture won t display in full screen The remote control does not work HD channels will have black bars on either side of the screen when displaying up scaled SD 4 3 contents Black bars on the Top amp Bottom will be shown on movies that have aspect ratios different from your TV Adjust the picture size options on your external device or TV to full screen Replace the remote control batteries with the poles in the right direction Clean the sensor s transmission window on the remote Try pointing the remote directly at the TV from 5 6 feet away The TV is making a humming noise Plasma TVs typically make a soft humming sound T
32. es to Gamma and White Balance To use select an option using the up and down arrow keys and the press ENTER Use the arrow keys to change value or setting and then press ENTER Advanced Settings Black Tone Off gt Dynamic Contrast Medium Gamma 0 Color Space Native White Balance Flesh Tone 30 Edge Enhancement On Move C Enter S Return E Black Tone Off Dark Darker Darkest Select the black level to adjust the screen depth W Dynamic Contrast Off Low Medium High Adjusts the screen contrast B Gamma Adjust the primary color intensity English 15 sounyee4 oiseg g0 Basic Features Color Space Auto Native Adjust the range of colors available to create the image White Balance Adjust the color temperature for a more natural picture R Offset G Offset B Offset Adjust each color s red green blue darkness R Gain G Gain B Gain Adjust each color s red green blue brightness Reset Resets the White Balance to it s default settings Flesh Tone Emphasize pink Flesh Tone Edge Enhancement Off On Emphasize object boundaries Picture Options MENU II Picture Picture Options ENTER s Picture Options Color Tone Normal Size 16 9 Digital Noise Filter Auto HDMI Black Level Normal Film Mode Off Screen Burn Protection Move 9 Enter 5 Return Color Tone Cool Normal Warm1 Warm2
33. fter long periods of use as heat dissipates from the panel through the vent hole in the upper part of the product This is normal and does not indicate any defect or operation failure of the product However children should be prevented from touching the upper part of the product The product is making a cracking noise A cracking noise may occur when the product contracts or expands due to a change in the surrounding environment such as temperature or humidity This is normal and not a defect of the unit Cell Defects The PDP uses a panel consisting of 2 360 000 HD level to 6 221 000 FHD level pixels which require sophisticated technology to produce However there may be a few bright or dark pixels on the screen These pixels will have no impact on the performance of the product e Avoid operating the TV at temperatures below 41 F 5 C e Astill image displayed too long may cause permanent damage to the PDP Panel Watching the Plasma TV in 4 3 format for a long period of time may leave traces of borders displayed on the left right and center ofthe screen caused by the difference of light emission on the screen Playing a DVD or a game console may cause similar effects to the screen Damages caused by the above effect are not covered by the Warranty e After images on the Screen Displaying still images from Video games and PC for longer than a certain period of time may produce partial after images To prevent th
34. g Electronics only f you use parts provided by another manufacturer it may result in a problem with the product or an injury due to the product falling The appearance may differ depending on the product i Be careful when you contact the TV because some parts can be somewhat hot Installation with a stand Installation with a wall mount 4 inches 4 inches 4 inches 4 inches 4 inches eit ee Be ee oe ee ee mu Engish SL Other Information 1 Caution Pulling pushing or climbing on the TV may cause the TV to fall In particular ensure your children do not hang over or destabilize the TV Doing so may cause the TV to tip over causing serious injuries or death Follow all safety precautions provided in the included Safety Flyer with your TV For added stability and safety you can purchase and install the anti fall device as described below The TV Holder Kit Sold Separately The parts below are included in the TV Holder kit In addition you need to provide a wood screw screw and molly or other screw appropriate for the wall or cabinet you intend to secure the TV Holder string to We recommend a size M4xL20 wood screw Ko y TV Holder BN96 15753A Screw M8 x L19 Installing the TV Holder 1 Remove the screw attached to the back of your TV and then connect the TV Holder to the TV with the screw included in the TV Holder Kit that is
35. g recorder 1 Select Recording amp When there are more than two recording devices When multiple recording devices are connected the recording devices are listed Select one recording device in the Device List When the recording device is not displayed select Device List and press the Red button to search for devices 2 Press the EXIT button to exit You can record the source streams by selecting Recording device_name amp Pressing the e REC button will record whatever you are currently watching If you are watching video from another device the video from the device is recorded Before recording check whether the antenna jack is properly connected to the recording device To properly connect an antenna to a recording device refer to the recording device s users manual D Listening through a Receiver You can listen to sound through a receiver i e Home Theater instead of the TV Speaker 1 Select Receiver and set to On 2 Press the EXIT button to exit 8 if your receiver supports audio only it may not appear in the device list i The receiver will work when you have properly connected the optical in jack of the receiver to the DIGITAL AUDIO OUT OPTICAL jack of the TV When the receiver i e Home Theater is set to On you can hear sound output from the TV s Optical jack When the TV is displaying a DTV air signal the TV will send out 5 1 channel sound to the receiver
36. hing Background Opacity You can change the background color of the caption This adjusts the opacity of the caption background Options include Default Transparent Translucent Solid and Flashing Return to Default This option sets each Size Font Style Foreground Color Background Color Foreground Opacity and Background Opacity to their defaults English 21 sounyee4 oiseg g0 Basic Features NOTE Digital Caption Options are available only when you can select Default and Service1 Service6 in Caption Mode The availability of captions depends on the program being broadcast The Default setting follows the standards set by the broadcaster You cannot set the Foreground and Background to the same color The Foreground and Background cannot be set to have the same color You cannot set both the Foreground Opacity and the Background Opacity to Transparent Melody Off Low Medium High Set so that a melody plays when the TV is turned on or off The Melody does not play When no sound is output from the TV because the MUTE button has been pressed When no sound is output from the TV because the volume has been reduced to minimum with the VOL button When the TV is turned off by Sleep Timer function Support Menu MENU II Support gt ENTERS Self Diagnosis Self Diagnostic might take few seconds this is part of the normal operation of the TV
37. his is normal It s caused by the electrical charges that are used to create the images on the screen If the humming sound is loud you may have set the brightness on the TV too high Try setting the brightness lower You can also have loud humming if the back of your Plasma TV is too close to a wall or other hard surface Also try rerouting your connection cables Improper installation of wall mount can create excessive noise 34 Engish Issues Solutions and Explanations Image Retention Burn In Issue To minimize the possibility of screen burn this unit is equipped with screen burn reduction technology Pixel Shift technology enables you to set picture movement up down Vertical Line and side to side Horizontal Dot The cable set top box remote control doesn t turn the TV on or off or adjust the volume Program the Cable Set remote control to operate the TV Refer to the Cable Set user manual for the SAMSUNG TV code A Mode Not Supported message appears Check the supported resolution of the TV and adjust the external device s output resolution accordingly Refer to the resolution settings on page 11 of this manual Caption on TV menu is greyed out Caption can not be selected in the TV menu when connected via HDMI or Component p 21 Caption must be activated on the external device p 21 There is a plastic smell from the TV This smell is normal and will dissipate over time
38. is effect reduce the brightness and contrast when displaying still images for a long time Warranty Warranty does not cover any damage caused by image retention Burn in is not covered by the warranty 2 English Contents E 18 Setting the Time 18 Ostot dores m CQ LEE i quem Sleep Timer 19 DEER SOE adiuti a Herat Setting the On Off Timer 19 Install the Stand sss 5 Locking Programs 19 Viewing the Control Panel sse 6 Economical Solutions 24 Remote Control Buttons 0 0 7 Other Features 21 Connecting to an Antenna or Cable Connection 8 Support Menu 22 Plug amp Play Initial Setup 8 Advanced Features Media Play 23 Connecting to an AV Device sssesse 9 Connecting a USB Device 23 Connecting to an Audio Device 10 ANNE ngsun a a a nacer tins 26 Connecting to a PC uses 11 Setting Up Anynet 27 Changing the Input Source sss 12 Switching between Anynet Devices 28 Recording 28 Listening through a Receiver 28 Troubleshooting for Anynet 29 How to Navigate Menus 12 cuna e bs Seeing Channels 3 Using Favorite Channels 13 Installing the Wall Mount ee 30 Memorizing Channels 18 e Securing the Installation Space wl Editing Channels 14 Securing the TV to the Wall 32 Other Features 14 e Troubleshooting uoces e 33 Picture
39. is for retail environments Toreturn the unit s settings from Store Demo to Home Use standard Press the volume button on the TV When you see the volume OSD press and hold MENU for 5 sec Selecting an antenna Press the A or V button then press the ENTER C button Select Air Cable or Auto Selecting and The channel search will start automatically This can take up to 30 minutes memorizing channels For more information refer to Channel Auto Program in the e Manual Press the ENTERC button at any time to interrupt the memorization process Setting the Set the Clock Mode automatically or manually Clock Mode e Auto Allows you to select DST Daylight Saving Time mode and time zone Manual Allows you to manually set the current date and time p 18 View the The connection method for the best HD screen quality is displayed HD Connection Guide Enjoy your TV Press the ENTER C button NO oc BO If You Want to Reset This Feature MENU II Setup Plug amp Play gt ENTERC NOTE e To change the TV s setting from Store Demo to Home Use when not in Plug amp Play press the volume button on the TV When you see the volume in the OSD press and hold MENU for 5 sec 8 English Connections Connecting to an AV Device Using an HDMI or HDMI DVI cable HD connection up to 720p 1080i We recommend using the HDMI connection for the best quality HD picture Available devices DVD player Blu r
40. its are entered the 16 ans Programming is not suitable for children Confirm New PIN screen appears Re enter the same under the age of 16 18 ans Programming 4 digits When the Confirm screen disappears your PIN restricted to adults has been memorized The V Chip will automatically block any category that deals with more sensitive material For How to watch a restricted channel example if you block the 8 ans category then 13 ans 16 ans and 18 ans will automatically be blocked also If the TV is tuned to a restricted channel the V Chip will block it The screen will go blank and the following message will appear This channel is blocked by V Chip Please enter the PIN to unblock it you forget the PIN press the remote control buttons in the following sequence which resets the pin to 0 0 0 0 POWER off MUTE gt 8 gt 2 gt 4 gt POWER on 20 Engish D Economical Solutions MENU II Setup gt ENTERC The Eco Function can be used to enhance your power savings Energy Saving Off Low Medium High This adjusts the brightness of the TV in order to reduce power consumption Until the screen turns on again a distorted picture will be displayed for about 4 seconds Eco Sensor Off On Eco Sensor detects surrounding light intensity using an optical sensor and adjusts the screen s brightness W Eco Sensor Off On Turns the sensor off or on 8 if you adjust the Ce
41. ll Light the Eco Sensor will be set to Off W Min Cell Light Manually adjust the screen brightness 0 10 If Eco Sensor is On the display brightness may change become slightly darker or brighter depending on the surrounding light intensity i Other Features MENU II gt Setup gt ENTERC Language Set the menu language 1 Select Language and then press ENTER Ls button 2 Choose a language and then press the ENTER C button Choose English Espafiol or Francais Game Mode Off On When connecting to a game console such as PlayStation or Xbox you can enjoy a more realistic gaming experience by selecting the game mode NOTE Precautions and limitations for game mode To disconnect the game console and connect another external device set Game Mode to Off in the setup menu If you display the TV menu in Game Mode the screen shakes slightly Game Mode is not available when the input source is set to TV or PC After connecting the game console set Game Mode to On Unfortunately you may notice reduced picture quality f Game Mode is On Picture mode is set to Standard and Sound mode is set to Movie Equalizer is not available Caption On Screen Text Messages Caption Off On You can switch the caption function on or off If captions are not available they will not be displayed on the screen The Caption feature doesn t w
42. lock first On Time A 00 am Inactvate bf Off Time 12 00 am Inactivate Volume Contents 20 TV Cable 3 Repeat Sun Mon Tue Wed Thu Fri Sat Once gH m m m H HM E 4 gt Move Adjust 9 Enter 5 Return On Time Off Time Set the hour minute and activate inactivate To activate the timer with the setting you ve chosen set to Activate Volume Set the desired volume level Use the left and right arrow buttons to change the volume level Contents Select a folder in the USB device containing music or photo files to be played when the TV is turned on automatically amp NOTE If there is no music file on the USB device or the folder containing a music file is not selected the Timer function does not operate correctly When there is only one photo file in the USB the Slide Show will not play If a folder name is too long the folder cannot be selected Each USB you use is assigned its own folder When using more than one of the same type of USB make sure the folders assigned to each USB have different names Repeat Select Once Everyday Mon Fri Mon Sat Sat Sun or Manual to set at you convenience If you select Manual you can set up the day you want to activate the timer y The v mark indicates the day is selected Auto Power Off available only when the TV is turned on by the Timer The TV will be automatically turned off after 3 hours of being left idle to prevent
43. lt position To use the Position function after selecting Screen Fit in HDMI 1080i 1080p or Component 1080i 1080p follow these steps 1 Press the lt or gt button to select Position 2 Press the ENTERC button 3 Press the A V lt or gt button to move the picture 4 Press the ENTERCS button 5 Press the lt or gt button to select Reset 6 Press the ENTER C button HD High Definition 16 9 1080i 1080p 1920x1080 720p 1280x720 You can adjust and store settings for each external device you have connected to an input on the TV Input Source Picture Size ATV AV 16 9 Zoom1 Component 480i 480p Zoom2 4 3 DTV 1080 16 9 4 3 Wide Fit Component 1080i 1080p Screen Fit HDMI 720p 1080i 1080p Digital Noise Filter Off Low Medium High Auto If the broadcast signal received by your TV is weak you can activate the Digital Noise Filter feature to reduce any static and ghosting that may appear on the screen amp When the signal is weak try other options until the best picture is displayed W HDMI Black Level Normal Low Lets you select the black level on the screen to adjust the screen depth Available only in HDMI mode W Film Mode Off Auto Sets the TV so that it senses automatically and then process film signals from all Sources and adjusts the picture for optimum quality 9X Available in TV AV COMPONENT 480i 10801 and HDMI
44. mall amount of electric power To be safe and to decrease power consumption do not leave your TV in standby mode for long periods of time when you are away on a holiday for example A small amount of electric power is still consumed even when the power button is turned off It is best to unplug the power cord 6 Engish Turns the TV on and off Press to directly access channels Press to select additional digital channels digital being broadcasted by the same station For example to select channel 54 3 press 54 then press and ug Adjusts the volume Brings up the OSD Displays Media Play USB p 23 Quickly select frequently used functions Returns to the previous menu Buttons used in the Channel list Media Play USB menu etc Installing batteries Battery size AAA ve P MITPPITLL Qmm Remote Control Buttons POWER SOURCE SAMSUNG NOTE Signs ee mew Displays and selects the available video sources p 12 Returns to the previous channel Cuts off the sound temporarily Changes channels Displays the channel list on the screen p 13 Automatically shuts off the TV at a preset time p 19 Displays information on the TV screen Selects the on screen menu items and changes the values seen on the menu Exits the menu MTS Press to choose stereo mono or Separate Audio Program SAP broadcast p
45. n the remote control To mute the sound press the dK MUTE button on the remote control W Repeat Music On Off Select to repeatedly play MP3 files in the current folder Playing Music Only displays files with the MP3 file extension Other file extensions are not displayed even if they are saved on the same USB device If the sound is strange when playing MP3 files adjust the Equalizer and SRS TruSurround HD in the Sound menu An over modulated MP3 file may cause a sound problem Music function information icons mST Repeat Music is On Al Repeat Music is Off g When pressing the gt Play uw Pause button on the remote control while music is playing g When pressing the m Stop button on the remote control the music stops Engish 25 Sejnjeoj peoueApv 0 Advanced Features Setup Using the Setup Menu W Slide Show speed Select to control the slide show speed You can select Fast Normal or Slow W Background Music Select to determine whether to play an MP3 file Background Music On during a slide show You can select Music On or Music Off Background Music Setting 3 P m Repeat Music On E Background Music Setting While a slide show is in progress use oe the Background Music Setting to select a music file to listen to JOE Remove Select an MP3 file as the background music W Repeat Music Select to determine whether to repeat playing
46. nary graphics and images on screen such as the dark side bars on non expanded standard format television video and programming should be limited to no more than 5 of the total television viewing per week Additionally viewing other stationary images and text such as stock market reports video game displays station logos web sites or computer graphics and patterns should be limited as described above for all televisions Displaying stationary images that exceed the above guidelines can cause uneven aging of PDP Displays that leave subtle but permanent burned in ghost images in the PDP picture To avoid this vary the programming and images and primarily display full screen moving images not stationary patterns or dark bars On PDP models that offer picture sizing features use these controls to view different formats as a full screen picture Be careful in the selection and duration of television formats you use for viewing Uneven PDP aging as a result of format selection and use as well as burned in images are not covered by your Samsung limited warranty e SAMSUNG ELECTRONICS NORTH AMERICAN LIMITED WARRANTY STATEMENT Subject to the requirements conditions exclusions and limitations of the original Limited Warranty supplied with Samsung Electronics SAMSUNG products and the requirements conditions exclusions and limitations contained herein SAMSUNG will additionally provide Warranty Repair Service in the United States on SAMSUNG products purch
47. ng an HDMI cable 2 Connect the HDMI IN jack of the home theater and the HDMI OUT jack of the corresponding Anynet device using an HDMI cable 26 English NOTE You must connect an Anynet device using an HDMI cable Some HDMI cables may not support Anynet functions Anynet works when the AV device supporting Anynet is in the standby or on status Anynet supports up to 12 AV devices in total Note that you can connect up to 3 devices of the same type However you can connect only one Home Theater Anynet Menu The Anynet menu changes depending on the type and status of the Anynet devices connected to the TV saunjeej4 peoueapy vo Anynet Menu Description View TV Changes Anynet mode to TV broadcast mode Device List Shows the Anynet device list Recording recorder Starts recording immediately using the recorder This is only available for devices that support the recording function Stop Recording recorder Stops recording device_name MENU Shows the connected device menus For example if a DVD recorder is connected the disc menu of the DVD recorder will appear device_name INFO Shows the play menu of the connected device E g If a DVD recorder is connected the play menu of the DVD recorder will appear Receiver Sound is played through the receiver If you have connected more than one recording device they are displayed as recorder If you have connnected only
48. ng the Add to Favorite or Delete from Favorite menu respectively 6 Air Y TV ft6 Delete Timer Viewing Channel Name Edit Select All Y TV 9 Auto Program S euueut Peppy Il Memorizing Channels MENU II Channel gt ENTERC Antenna Air Cable Before your television can begin memorizing the available channels you must specify the type of signal source that is connected to the TV i e an Air or a Cable system Auto Program Wi Air Air antenna signal HM Cable Cable antenna signal E Auto Air and Cable antenna Engish 13 sounyee4 oiseg g0 Basic Features NOTE When selecting the Cable TV system STD HRC and IRC identify various types of cable TV systems Contact your local cable company to identify the type of cable system that exists in your particular area At this point the signal source has been selected After all the available channels are stored it starts to remove scrambled channels The Auto Program menu then reappears B Editing Channels MENU II Channel Channel List gt ENTER Channel Name Edit 1 Select a channel and press the TOOLS button 2 Edit the channel name using the Channel Name Edit menu W Channel Name Edit analog channels only Assign your own channel name Other Features MENU II Channel ENTERC Clear Scrambled Channel This function is used to filter out scrambled channels after Auto Program is completed This
49. ngth Digital channels only An HD channel s reception quality is either perfect or the channels are unavailable Adjust your antenna to increase signal strength Software Upgrade TV Side Panel The Software Upgrade menu lets you upgrade your TV s software to the latest version Current Version This is the Software version already installed in the TV i When software is upgraded video and audio settings you have made will return to their default factory settings OE USB Drive i We recommend you write down your settings so that you can easily reset them after the upgrade HD Connection Guide Refer to this information when connecting external devices to the TV Contact Samsung View this information when your TV does not work properly or when you want to upgrade the software You can find information regarding our call centers and how to download products and software Advanced Features Enjoy photos and or music files saved on a USB Mass Storage Class MSC device USB SUM 315 0MB 495 0MB Free MENU II Application Media Play USB ENTER di soinjee4 peoueApv 0 Ls Enter Exit i Connecting a USB Device 1 Turn on your TV TV Side Panel 2 Connect a USB device containing photo and or music files to the USB jack on the side of the TV 3 When the Application selection screen is displayed press the button to select Media Play USB
50. one recording device it is displayed as device name D Setting Up Anynet MENU IIT Application Anynet HDMI CEC gt ENTER CY W Setup Anynet HDMI CEC Off On To use the Anynet Function Anynet HDMI CEC must be set to On 3 When the Anynet HDMI CEC function is disabled all the Anynet related operations are deactivated Auto Turn Off No Yes Set an Anynet Device to turn off automatically when the TV is turned off f Auto Turn Off is set to Yes running external devices will turn off at the same time as the TV powers off However a device may not turn off if recording is in progress Qy May not be enabled depending on the device Engi 27 Advanced Features lH Switching between Anynet Devices 1 Anynet devices connected to the TV are listed 8 if you cannot find a device you want press the Red button to refresh the list 2 Select a device and then press the ENTER Cs button You can switch to the selected device i The Device List menu appears only when you set Anynet HDMI CEC to On in the System menu Switching to the selected device may take up to 2 minutes You cannot cancel the operation during the switching operation f you have selected an external input mode by pressing the SOURCE button you cannot use the Anynet function Make sure to switch to an Anynet device by using the Device List D Recording You can make a recording of a TV Program using a Samsun
51. ork with devices connected to the TV through the Component HDMI or PC input jacks Caption Mode You can select the desired caption mode The availability of captions depends on the program being broadcast Default CC1 CC4 Text1 Text4 analog channels only The Analog Caption function operates in either analog TV channel mode or when a signal is supplied from an external device to the TV Depending on the broadcasting signal the Analog Caption function may not work with digital channels Default Service1 Service6 CC1 CC4 Text1 Text4 digital channels only The Digital Captions function works with digital channels YX Service1 6 may not be available in digital caption mode depending on the broadcast Digital Caption Options digital channels only Size Options include Default Small Standard and Large The default is Standard Font Style Options include Default and Styles 0 to 7 The default is Style 0 Foreground Color You can change the color of the letters Options include Default White Black Red Green Blue Yellow Magenta and Cyan You can change the color of the letter The default is White Background Color This adjusts the opacity of text Options include of Default White Black Red Green Blue Yellow Magenta and Cyan You can change the background color of the caption The default is Black Foreground Opacity Options include Default Transparent Translucent Solid and Flas
52. oth BN63 01798B e Warranty Card Safety Guide Quick Setup Guide Ferrite Core 2EA 8301 002049 i Ferrite Core for Power Cord The ferrite cores are used to shield the cables from interference When connecting the ferrite core to a cable open the ferrite core and clip it around the cable near the plug as shown in the figure A H H w A One ferrite core should be no more than 8 inches from the end of the cord that is inserted into the TV B If your TV came with a second ferrite core the 43 inch model the second core should be no more than 3 4 inches from the end of the cord that is inserted into the AC outlet Power Cord Ferrite Core The ferrite cores are used to shield the cables from interference When connecting a cable open the ferrite core and clip it around the cable near the plug as shown in the figure 61 inch model only Antenna Cable Component Cable sold separately Input Cables Sold Separately da HDMI HDMI DVI Component Composite AV Coaxial RF 4 Engish Install the Stand See separate guide for installing the stand o 3 al my x4 M4 X L12 ae a o mp x4 MA X8 3 Stand 1EA Guide Stand 1EA Screws 8EA Follow the steps below to connect the TV to the stand X4 i Top View H LI 1 J ATTENTION 1 DO NOT USE DONOTUSE DO NOT USE i CHEMICALS GREASE OIL i 1 1 Connect the Guide Stand to the Stand using four s
53. overheating H Locking Programs V Chip The V Chip feature automatically locks out programs that are deemed inappropriate for children The user must enter a PIN personal identification number before any of the V Chip restrictions are set up or changed NOTE V Chip is not available in HDMI Component or PC mode The default PIN number of a new TV set is 0 0 0 0 Allow All Press to unlock all TV ratings Block All Press to lock all TV ratings W V Chip Lock Off On You can block rated TV Programs TV Parental Guidelines You can block TV programs depending on their rating This function allows you to control what your children are watching TV Y Young children TV Y7 Children 7 and over TV G General audience TV PG Parental guidance TV 14 Viewers 14 and over TV MA Mature audience ALL Lock all TV ratings FV Fantasy violence V Violence S Sexual situation L Adult Language D Sexually Suggestive Dialog The V Chip will automatically block certain categories dealing with more sensitive material For example if you block the TV Y category then TV Y7 will automatically be blocked Similarly if you block the TV G category then all the categories in the young adult group will be blocked TV G TV PG TV 14 and TV MA The sub ratings D L S V work similarly So if you block the L sub rating in TV PG then the L sub ratings in TV 14 and TV MA will automatically be
54. process may take up to 20 30 minutes How to Stop Searching Scrambled Channels 1 Press the ENTER CS button to select Stop 2 Press the lt button to select Yes 3 Press the ENTER C button i This function is only available in Cable mode Channel List Channel List Option Menu Set each channel using the Channel List menu options Add Delete Timer Viewing Select All Deselect All Option menu items may differ depending on the channel status 1 Select a channel and press the TOOLS button 2 Select a function and change its settings 14 Engish E Add Delete Delete or add a channel to display the channels you want NOTE All deleted channels will be shown on the All Channels menu A gray colored channel indicates the channel has been deleted The Add menu only appears for deleted channels Delete a channel from the Added Channels or Favorite menu in the same manner W Timer Viewing You can set a desired channel to be displayed automatically at the reserved time Set the current time first to use this function 1 Press the lt gt A V buttons to select the desired channel in Channel List 2 Press the TOOLS button then select Timer Viewing 3 Scroll up or down to adjust the settings in the box or use the numeric buttons on your remote to enter the date and time 8 qf you selected Once Everyday Every Week Mon Fri Mon Tue Wed Thu or Sat Sun in Repeat you can enter the date
55. s and the speakers attached to your audio receiver If this occurs set the TV to External Speaker When you set Speaker Select to External Speaker he TV s speakers are turned off You will hear sound hrough the external speakers only When you set Speaker Select to TV Speaker both the TV s speakers and the external speakers are on You will hear sound hrough both When Speaker Select is set to External Speaker TV Speaker Off External Speaker On When Speaker Select is set to TV Speaker TV Speaker On External Speaker On amp If there is no video signal both the TV s speakers and the external speakers will be mute 18 Engish Sound Reset Reset All Reset Sound Mode Cancel W Reset All Restore all sound settings to the factory defaults W Reset Sound Mode Returns all sound values in the currently selected mode to the default settings Il Setting the Time MENU II Setup gt Time gt ENTER C Time B Clock Setting the clock to use the various timer features of the TV The current time will appear every time you press the INFO button 8 oq you disconnect the power cord you have to set the clock again Clock Mode Auto Manual Auto Have TV set the current time automatically using the time from a digital channel 9i You must have the cable or antenna connected to the TV to set the time automatically Manual Set the current time manually 83 Depending on the bro
56. s may be released automatically when connected to the TV f a USB extension cable is used the USB device may not be recognized or the files on the device may not be read f a USB device connected to the TV is not recognized the list of files on the device is corrupted or a file in the list is not played connect the USB device to the PC format the device and check the connection If a file deleted from the PC is still found when Media Play is run use the Empty the Recycle Bin function on the PC to permanently delete the file Photo Viewing a Photo or Slide Show 1 Press the INFO button to display the option View Start Slide Show Delete Delete All Deselect All 2 Press the A or V button to select Start Slide Show then press the ENTER C button amp During the slide show files are displayed in order from the currently shown file MP3 files can be automatically played during the Slide Show Po if the Default Background Music is set to On To enable this function MP3 files and other photo files must be located in the LES n Option M Play 9 Return same folder on the USB Memory Device Cedo Feci i Press the INFO button during the slide show to set the following options Slide Show Speed Background Music Background Music Setting List Press the A or V button to select the option then press the ENTERC button After setting the option press the ENTER C button to make a change i Press the
57. sound experience through a pair of speakers using HRTF Head Related Transfer Function technology Engin 17 sounyee4 oiseg g0 Basic Features Preferred Language digital channels only Use the up and down arrow keys to select a language and then press ENTER Digital TV broadcasts can simultaneously transmit many audio tracks for example simultaneous translations of the program into foreign languages You can only select a language from among the being broadcasted Multi Track Sound MTS analog channels only W Mono Choose for channels that are broadcasting in mono or if you are having 7 difficulty receiving a stereo signal W Stereo Choose for channels that are broadcasting in stereo W SAP Choose to listen to the Separate Audio Program which is usually a foreign language translation 83 Depending on the program being broadcast you can listen to Mono Stereo or SAP Auto Volume Off On Normal equalizes the volume level on each channel so that when you change channels the volume level is the same Night equalizes and decrease the volume level on each channel so each channel is quieter Night is useful at night when you may want to keep the volume low Speaker Select External Speaker TV Speaker If you are listening to the sound track of a broadcast or movie through an external receiver you may hear a sound echo caused by the difference in decoding speed between the TV s speaker
58. sources name you want B VCR DVD Cable STB Satellite STB PVR STB AV Receiver Game Camcorder PC DVI PC DVI TV IPTV Blu ray HD DVD DMA Name the device connected to the input jacks to make your input Source selection easier Qy f you have connected a PC to the HDMI IN 1 DVI port with an HDMI cable select PC under Edit Name to enter a device name if you have connected a PC to the HDMI IN 1 DVI port with an HDMI to DVI cable select DVI PC under Edit Name to enter a device name f you connected an AV device to the HDMI IN 1 DVI port with an HDMI to DVI cable select DVI Devices mode under Edit Name to enter a device name How to Operate the OSD On Screen Display The access steps may differ depending on the selected menu The main menu options appear on the screen Picture Sound Channel Setup Input Application Support 1 MENU m 2 A V Select an icon or option with the A or V button 3 ENTER s Press ENTER C to access the sub menus 4 A V Select the desired submenu with the A or V button 5 4 Adjust the value of an item with the lt or gt button The adjustment in the OSD may differ depending on the selected menu 6 ENTER s Press ENTER Ls to confirm the selection 7 EXIT i Press EXIT Channel Menu Seeing Channels Channel List The Channel List contains the channels your TV displays added channels when you press the Channel button on your remote
59. standard screw Specifications Screws that are too long may cause damage to the inside of the TV set For wall mounts that do not comply with the VESA standard screw specifications the length of the screws may differ depending on the wall mount specifications Do not fasten the screws too firmly This may damage the product or cause the product to fall leading to personal injury Samsung is not liable for these kinds of accidents Samsung is not liable for product damage or personal injury when a non VESA or non specified wall mount is used or the consumer fails to follow the product installation instructions Do not mount the TV at more than a 15 degree tilt Always have to people mount the TV on a wall 30 English VESA scew Product Family iod p Bn EO Quantity millimeters 42 50 400 X 400 uoneuuoju Jeu O S0 58 63 600X400 PDP TV M8 4 70 79 800X400 80 1400 X 800 Unscrew the hole around before installing Wall Mount on the wall Do not install your Wall Mount Kit while your TV is turned on It may result in personal injury due to electric shock Securing the Installation Space Keep the required distances between the TV tne wall and other objects to ensure proper ventilation Failing to do so may result in a fire or a problem with the TV caused by an increase in the internal temperature of the product When using a stand or wall mount use parts provided by Samsun
60. the MOS ESUERGS S Rm music when all MP3 files in the current folder have been played H Screen Saver Select to set the waiting time before the screen saver appears The screensaver will appear when no button is pressed for 10 min 20 min 40 min 1 hour or Off W Safe Remove You can remove the device safely from the TV Playing the selected photos music files 1 Press the Yellow button 2 Repeat the above operation to select desired photos music files Selected photos or files are marked with the symbol w To cancel a selection press the Yellow button again 3 Press the gt Play ENTER Cs button to play the selected photos or files What is Anynet Anynet is a function that enables you to control all connected Samsung devices that support Anynet with your Samsung TV s remote The Anynet system can be used only with Samsung devices that have the Anynet feature To be sure your Samsung device has this feature check if there is an Anynet logo on it To connect to a Samsung Home Theater TV Anynet Device 1 Home Theater Anynet Device 2 3 DIGITAL ALDIOIN HDMI Cable Not Supplied HDMI Cable Not Supplied HDMI Cable Not Supplied Optical Cable Not Supplied 1 Connect the HDMI IN 1 DVI 2 jack on the TV and the HDMI OUT jack of the corresponding Anynet device usi
61. then press the ENTER C button qt USB Drive Using the Media Play Menu Viewing a Photo or Slide Show 1 Press the MENU button Press the A or V button to select Application then press the ENTER Cs button 2 Press the A or V button to select Media Play USB then press the ENTER C4 button 3 Press the A or V button to select the corresponding USB Memory Device then press the ENTER C button The Media Play menu differs depending on the USB Memory Device connected to TV Some devices may not be supported due to compatibility problems 4 Pressthe 4 or button to select an icon Photo Music Setup then press the ENTER C button Photo 307 2MB 973 7MB Music Setup 4 gt Move Enter 5 Return 8 it might not work properly with unlicensed multimedia files Need to Know List before using Media Play USB Only alphanumeric characters must be used as a folder name or file name photo music The file system only supports FAT16 32 The NTFS file system is not supported Certain types of USB Digital camera and audio devices may not be compatible with this TV Media Play USB only supports the USB Mass Storage Class device MSC MSC is a Mass Storage Class Bulk Only Transport device Examples of MSC are Thumb drives and Flash Card Readers Both USB and HUB are not supported Before connecting your device to the TV please back up your files to prevent them from damage or loss of data SAMSUN
62. through the receiver Connect the optical cable between TV and the receiver English 29 saunjeej4 peoueApy vo Other Information Attaching the Blanking Bracket When installing the TV onto a wall attach the Blanking Bracket as shown Installing the Wall Mount Kit The wall mount kit sold separately allows you to mount the TV on the wall For detailed information on installing the wall mount see the instructions provided with the wall mount Contact a technician for assistance when installing the wall mount bracket Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the TV on your own Wall Mount Kit Specifications VESA i The wall mount kit is not supplied but sold separately Install your wall mount on a solid wall perpendicular to the floor Before attaching to surfaces other than plaster board please contact your nearest dealer for additional information If you install the TV in a wall mount on a ceiling or slanted wall it may fall and result in severe personal injury 8 NOTE Standard dimensions for wall mount kits are shown in the table below Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided Do not use screws that do not comply with the VESA standard screw specifications Do not use screws that are longer than the standard length or do not comply with the VESA
63. u ray player cable box STB satellite receiver directly to an amplifier or home theater Using an EX Link Cable Connection Available Devices External devices that support EX Link EX LINK EX LINK Connector for service only 10 Engish Connecting to a PC Using an HDMI DVI Cable Suonoeuuo Z0 Audio Cable Not Supplied AUDIO OUT n DV OUT AUDIO IN HDMI to DVI Cable Not Supplied Your PC may not support an HDMI connection Display Modes HDMI DVI Input Optimal resolution e PN43D440 PN43D450 1024 X 768 60Hz PN51D440 PN51D450 1360 X 768 60Hz Horizontal Vertical Pixel Clock Syne Polarity Mode Resolution Frequency Frequency Frequency y H V PN43D450 PN51D450 KHz Hz MHz IBM 640 x 350 31 469 70 086 25 175 Vv Vv 720 x 400 31 469 70 087 28 322 Vv Vv MAC 640 x 480 35 000 66 667 30 240 Vv Vv 832 x 624 49 726 74 551 57 284 Vv Vv 720 x 576 35 910 59 950 32 750 v Vv eee 1280 x 720 56 456 74 777 95 750 v 640 x 480 31 469 59 940 25 175 Vv Vv 640 x 480 37 500 75 000 31 500 Vv Vv 640 x 480 37 861 72 809 31 500 Vv v 800 x 600 37 879 60 317 40 000 Vv v 800 x 600 46 875 75 000 49 500 Vv Vv VESA DMT 800 x 600 48 077 72 188 50 000 Vv Vv 1024 x 768 48 363 60 004 65 000 Vv Vv 1
64. your PC power settings Make sure the AC power cord is plugged in securely to the wall outlet and the TV When watching TV from an antenna or cable connection the TV will turn off after 10 15 minutes if there is no signal There is no picture video Check cable connections remove and reconnect all cables connected to the TV and external devices Set your external device s Cable Sat Box DVD Blu ray etc video outputs to match the connections to the TV input For example if an external device s output is HDMI it should be connected to an HDMI input on the TV Make sure your connected devices are powered on Be sure to select the TV s correct source by pressing the SOURCE button on the remote control Reboot the connected device by reconnecting the device s power cable RF Cable Antenna Connection The TV is not receiving all channels Make sure the coaxial cable is connected securely Please try Auto Program to add available channels to the channel list Go to MENU Channel Auto Program then select Auto and make sure the correct Cable TV signal type is set in the menu There are 3 options STD HRC and IRC p 13 Verify the Antenna is positioned correctly No Caption on digital channels Check Caption Setup menu Try changing Caption Mode Service1 to CC1 p 21 Some channels may not have caption data The picture is distorted macro block error small block dots pixelization Compression of vid

Samsung PN43D450A2D

Contents

Download Pdf Manuals

Related Search

Related Contents