Audiovox ANT3038XR television antenna
Contents
1. to the Company at the address shown below Do not return this product to the Retailer This Warranty is not transferable and does not cover product purchased serviced or used outside the United States or Canada The warranty does not extend to the elimination of externally generated static or noise This Warranty does not apply to costs incurred for installation removal or reinstallation of the product or if in the Company s opinion the product has been damaged through acts of nature alteration improper installation mishandling misuse neglect or accident This warranty does not cover damage caused by an AC adapter not provided with the product THE EXTENT OF THE COMPANY S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND IN NO EVENT SHALL THE COMPANY S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT This Warranty is in lieu of all other express warranties or liabilities ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO DURATION OF THIS WARRANTY ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY MUST BE BROUGHT WITHIN A PERIOD OF 24 MONTHS FROM THE DATE OF ORIGINAL PURCHASE IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER No person or representative is authorized to assume for the Company any liability other tha2. ANT3038XR Outdoor Antenna User s Guide Para obtener instrucciones en espa ol consulte la pagina 9 Assembling the ANT3038XR BEFORE YOU START Please read the IMPORTANT SAFETY INFORMATION sheet included in this package Step 1 Unpack Remove all three sections of the antenna and the hardware bag from package Make sure the following parts are in the package e 8 Antenna sections rear large middle and front booms e 1 Boom brace e 2 Reflector booms e 1 Hardware bag The hardware bag contains the following pieces 2 U Bolts 4 1 4 Flange nuts 2 Mast clamp inserts 5 End caps 10 10 Flange nuts 4 10 Screws 8 10 Washers 1 Matching transformer Boom Brace Large Boom Rear Boom L Front Boom lt 4 Reflector Mast a Booms Not Included fa Fig 1 ANT3038XR fully assembled mast not inclued English Step 2 Connect the reflector booms to the front small boom Find the two reflector booms and the front or small boom The two smaller elements on the reflector booms face away from the small main boom IMPORTANT Unfold the elements on each end of the reflector boom so that the front of their locking tabs face towards each other The remaining locking tabs can be unfolded in either direction Make sure that all of the elements are perpendicular to the reflector boom Connect the two refl
3. a 10 nut on top of each stud but don t tighten them yet Place the transformer ends between the two washers and tighten the nuts securely See figure 10 Attach the coax downlead to the transformer Downlead connections Transformer English Step 10 Insert end caps Insert two of the plastic end caps in the ends of the antenna as shown in figure 11 Insert a third plastic end cap in the exposed end of the boom brace Insert the last two end caps on the ends of the reflector booms Use a rubber mallet to gently tap them into the ends so that they are secure Step 11 Mount the antenna to a mast 0 Nuts Find the two U bolts four 1 4 flange nuts and the A A two mast clamp inserts Place the mast clamp inserts on the inside of the mast clamps on the antennas as shown in figure 12 Then insert the U bolts into the mast clamps and mast clamp inserts Attach the nuts loosely Slide the antenna over the mast and lightly tighten the two mast clamps See figures 12 and 13 The top side of the antenna is the side with the black plastic pieces on it Step 12 Connect the coax downlead to your TV or preamplifier Connect the coax downlead to your TV Rotate the antenna until you receive the best picture You will probably Point toward need a helper to view the TV set broadcast while you are rotating the antenna towers NOTE Point the small end of the antenna towards the stati
4. ector booms to the front boom using two of the provided 10 nuts and screws The reflector booms should be parallel to the smaller boom at this point See Fig 1 Main Boom Step 3 Unfold the rest of the antenna Unfold all the other elements on the antenna until they lock into place ensuring that they are flat and parallel to each other See Fig 3 Step 4 Connect the middle large section to the front small section English Find the middle large section Locate the end of the middle section that matches figure 4 Remove the nut and screw in the center Slide the narrow boom of the front small section into the middle large section Make sure the phasing lines are on the top side of the small boom and the black plastic element holders Middle Front are also on this same side section q SecHon This is the top of the antenna See figure 5 Tap lightly with a rubber mallet on the end of the small boom aligning the holes for the screw See figure 4 Re install the screw and nut be sure to tighten securely Step 5 Connect the phasing lines Place the phasing lines from the front section over the studs Secure them to the studs with 10 flange nuts and washers Tighten securely Phasing Lines Step 6 Connect the rear section to the middle large section On the open end of the middle large section remove the rear nut and scre
5. n expressed herein in connection with the sale of this product Some states provinces do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you This Warranty gives you specific legal rights and you may also have other rights which vary from state province to state province U S A Audiovox Electronics Corporation 150 Marcus Blvd Hauppauge NY 11788 CANADA Audiovox Return Center c o Genco 6685 Kennedy Road Unit 3 Door 16 Mississauga Ontario LST 3A5
6. on s Important Point The Antenna Toward Your Local Broadcast Towers Visit www antennaweb org to see the locations of your local broadcast towers This information is crucial in pointing your antenna correctly Step 13 Secure mast clamps and downlead ground the antenna Tighten the two mast clamps securely Secure the coaxial downlead to the mast using cable ties or electrical tape to prevent it from whipping by the wind Ground the antenna and mast per the accompanying grounding instructions Antenna Removal Removal of the antenna should be exactly the reverse of the installation instructions Please for your own safety follow the instructions for installing the antenna starting with the last step first English 12 Month Limited Warranty Audiovox Electronics Corporation the Company warrants to the original retail purchaser of this product that should this product or any part thereof under normal use and conditions be proven defective in material or workmanship within 12 months from the date of original purchase such defect s will be repaired or replaced at the Company s option without charge for parts and repair labor To obtain repair or replacement within the terms of this Warranty the product along with any accessories included in the original packaging is to be delivered with proof of warranty coverage e g dated bill of sale specification of defect s transportation prepaid
7. w Find the rear section Slide the narrow boom of the rear antenna into the middle large section Tap lightly with a rubber mallet on the end of the small boom aligning the holes for the screw See figure 6 Re install the screw and nut be sure to tighten securely Step 7 Connect the phasing lines 1 I Phasing Nut lis S Washer 3 On the middle large section near where the middle and rear sections come together find the posts on the top and bottom of the last element holder studs See figure 7 Place the phasing lines from the rear section over the studs one on the top side and one on the bottom Then fasten them to the posts with washers and 10 flange nuts Tighten securely Step 8 Connect the boom brace Lay the boom brace on top of the antenna Make sure the mast clamps the brass colored sections on the boom brace and antenna are facing the same direction Locate the screw hole in the reflector boom and attach the brace with one of the provided 10 screws and nuts See figure 8 Swing the boom brace down towards the rear Form a V with the metal straps Use one of the provided 10 screws and nuts to attach the V to each side of boom See figure 9 Step 9 Install the transformer Find the downlead connection on the bottom of the front section of the antenna just beyond the reflector booms Place two washers on each of the studs Place
Download Pdf Manuals
Related Search