JVC TK-C215VP4E surveillance camera
Contents
1. After setting is complete mount the inner dome to the camera 1 Mounting the inner dome Mount the inner dome to the 3 clips ony Clip x 3 AA 22 oe T Inner Dome TK C215VP4 is used in the above illustration fel S Note Mount the inner dome such that it does not cover the lens When mounting the inner dome make sure not to move the position of the lens Doing so may cause the preset angle of view to go out of alignment 30 Mounting the dome cover 1 Cleaning the dome cover Before mounting remove any dust or dirt from the dome cover Memo Dirt that is not removed from the cover before mounting may appear on the camera s image Memo Do not apply excessive force to the dome cover such as stretching it 2 Mounting the dome cover to the base Mount the dome cover by aligning the 3 position marks on the base with the dome cover 3 Fastening the dome cover Fasten by tightening the 3 fastening screws of the dome cover using the wrench supplied TI ZZ Position Alignment Mark 3 22 mA d 7 Wrench Supplied TK C215VP4 is used in the above illustration Note Make sure that the dome cover is firmly fastened Otherwise the humidity level may rise which may result in fogging and even falling of the cover Ensure that the fall prevention wire of the dome cover is not caught in the space betwe2. 1 AGC OFF ON 2 SELECT PHASE WHT BAL 3 SYNC LL INT 4 WHT BAL ATW MANU 5 BLC OFF ON 6 DAY NIGHT OFF ON 7 RESERVED SET TO OFF 8 RESET SPOT RESET SPO When adjusting the phase Press the or button to adjust the phase Function selection switches 1 AGC Auto gain control switch Setting this switch to automatically increases the sensitivity even when the brightness of the subject is insufficient Default setting ON 2 SELECT WHT BAL PHASE setting switch WHT BAL The R B buttons are used as R B adjustment buttons PHASE The R B buttons are used as adjustment buttons Default setting WHT BAL 3 SYNC Synchronization system selection switch This switch sets the synchronizing system for the camera INT This is set for internal synchronization LL Line Lock The camera s vertical synchronization is locked to the AC 24 V 60 Hz or 50 Hz power line frequency When switching between multiple cameras using a switcher selecting this mode and adjusting the vertical phase can reduce the monitor sync disturbances occur that when the camera image is switched U type 60 Hz only E type 50 Hz only Default setting INT 4 WHT BAL ATW MANUAL selection switch For selecting whether to adjust the white balance automatically or manually When the setting is changed from manual to ATW the setting values in the manual mode w
3. TK C215VP4U E 20 140 220 eof 450 720ft extension 130m 350m 550 Without heater 24 i420 18001 TK C215VP4U E Maximum 40m 120m 180m extension 24 asot 590ft With heater TK C215VP12U E pc12y 90 m 80m 130 Marri oof eof 430ft extension 80m 210m 340 Without heater 24 1120ft TK C215VP12U E Maximum 30m 90m 140m extension AC 4V B00 Ht 460ft With heater Cable Maximum extension No cable compensator RG 59 200m RG 6 350m RG 11 450m Note e If thin cables are used i e with a high resistance a significant voltage drop will occur when the unit is at its maximum power consumption Either use a thick cable to restrict the voltage drop at the camera side to below 10 96 or place the power supply near to the camera When the voltage is low the protection circuit within the camera may be triggered and the power of the camera may turn off automatically Do not allow input from both a DC 12 V and AC 24 V power supply at the same time When using a DC 12 V power supply ensure that the polarities of the cable are correct The product shall be powered by Class 2 only The AC 24 V power supply should conform to the following U type Class 2 only E type Isolated power supply only 17 Installation and C
4. When this unit is moved from a cold to a warm place dew condensation may occur which may result in camera malfunctioning In this case leave this unit at room temperature for about 1 hour before turning on the power The rotation angle of this unit has been enlarged to enable installation at a wide variety of locations When the zoom function of the lens is set to Wide and the tilt angle set close to 70 a portion of this unit may be visible on the shooting screen depending on the rotation angle When this occurs adjust the angle of view accordingly r amp Pg 25 To prevent fogging due to changes in temperature make sure to insert the supplied silica gel into the designated location c Pg 24 When the supply voltage of the camera is low the input protection circuit within the camera may be triggered and the power of the camera may turn off automatically Make sure to use a power supply and voltage for the camera that is within 10 of the rated voltage All Interconnecting Equipment must be UL Listed Upon switching between the HOME and ALARM positions the camera focus may change slightly after the zoom operation comes to a stop This is due to the built in lens performance and is not a malfunction TK C215VP12U E only Introduction Precautions for proper use of this product continued Maintenance Turn off the power before performing maintenance Clean the dome cover using a lens cleaning
5. Do not overload wall outlets and extension cords as this can result in fire or electric shock 14 Never push objects of any kind into this appliance through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the appliance 15 Do not attempt to service this appliance yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 16 Unplug this appliance from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power cord or plug is damaged or frayed b If liquid has been spilled into the appliance c If the appliance has been exposed to rain or water d If the appliance does not operate normally by following the operating instructions Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the appliance to normal operation e If the appliance has been dropped or the cabinet has been damaged f When the appliance exhibits a distinct change in performance this indicates a need for service 17 When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics
6. E 3 8 mm to 45 6 mm Ambient temperature 10 to 50 14 F to 122 F Operation 0 C to 40 C variable 32 F to 104 F Recommended When using KA ZH215 30 C to 50 C 22 F to 122 F Operation 20 C to 40 C 4 F to 104 F Recommended Zoom ratio TK C215VPAU E Approx 3 6 TK C215VP12U E Approx 12 Maximum aperture TK C215VPAU E F1 3 f 2 8 mm to F3 0 f 10 mm TK C215VP12U E F1 6 f 3 8 mm to F2 7 Dustproof Waterproof f 45 6 mm IP 66 Angle adjustment range Mass Pan 175 TK C215VP4 Approx 1250 g Rotation 24175 TK C215VP12 Approx 1310 g Tilt 70 onl Accessories Angle of vision U type TK C215VPAU E 2 8 IrniStructioris oe eed 1 73 x 54 V Installation Precautions 1 iy bn 15 V Warranty Card M M E 1 Service Information 1 Ties eve tnodo elc 1 52 x 39 V Wrench cccscesescseescscscesesesecsesececsesecscseescseseenees 1 f 10 mm Template reci re 1 4 5 x 3 4 V E type Instructions Anaad 1 General Installation Precautions 1 Power supply Silica Gel peo pte dett tte 1 U type AC 24 V 60 Hz WICNCH i itte tha Spectre ra rudes 1 DC 12V Termplate c leno di e Rees 1 E type AC 24 V 50 Hz 60 Hz DC 12V Power consumpt
7. and brightness Upon determining the imaging direction adjust the angle of view focus and brightness accordingly Note When adjusting the focus make sure to cover the dome cover over the lens The dome cover of this unit is thick Therefore if the focus is not adjusted with the dome cover covered this may cause the lens to go out of focus when the dome cover is mounted When adjusting the focus cover the dome cover such that its center is perpendicular to the light axis of the lens and make sure that the image is not distorted See illustration below UA MUT I I M MI UA TK C215VP4U E is used in the above illustration TK C215VP4U E rs Pg 26 TK C215VP12U E r Pg 28 26 TK C215VPAU E Iris Level Adjustment Dial KD O IRIS LEVEL gt Focus Adjustment Button FOCUS ADJUST Zoom Adjustment Focus Adjustment Ring 46 Adjusting the angle of view Loosen the fastening screw for the zoom adjustment ring and move the ring to the left right to adjust the image Adjusting the focus Press the focus adjustment button The iris will be released for about 30 seconds Loosen the fastening screw for the focus adjustment ring and move the ring to the left right to align the focus Memo Set by repeating Adjusting the angle of view and Adjusting the focus for 2 to 3 times After adjustment is completed fasten by tightening each of the fast
8. as the original part Unauthorized substitutions may result in fire electric shock or other hazards 18 Upon completion of any service or repairs to this appliance ask the service technician to perform routine safety checks to determine that the appliance is in safe operating condition N oc POND Safety Precautions FOR USA AND CANADA CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash wish arrowhead symbol within an equilateral triangle isintended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure thatmay be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert theuser to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance INFORMATION FOR CANADA RENSEIGNEMENT POUR CANADA This Class B digital apparatus complies with Canadian ICES 003 Cet appar il numerique de la Classe B est conforme la norme NMB 003 du Canada WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE AVERTISSEMENT POUR EVITER LES RISQUES D INCENDIE OU D E
9. cloth or soft cloth Wiping it with thinner or benzene may melt the surface or cause it to fog For tough stains wipe using a cloth that is dipped into a neutral detergent diluted with water followed by wiping with a dry cloth Energy Conservation When not in use turn off the power of the System to save energy Note on consumable parts TK C215VP12U E only The following parts are consumable and should be replaced after a certain number of hours or a count of operations The service lives given below are only typical values They may vary depending on the operating environment and conditions Note that the replacement of consumable parts is chargeable even when they are replaced before the termination of the warranty period Zoom lens assembly Zooming operation 2 million times Name of Parts Camera Mounting hole x 2 Use these when mounting the camera to the ceiling wall or electrical box Pg 21 r amp Pg 31 Note To mount the camera using the electrical box consult the dealer from which this product is purchased or any nearby JVC dealer Hole for Connecting Cable and Piping This is a hole for drawing out the connecting cable This hole can also be used to mount directly to pipes Piping hole G3 4 14UNC Pg 32 Mounting Screw for Fall Prevention Wire Use this screw when mounting the fall prevention wire to this unit Fall prevention wire is n
10. fastening the silica gel rs Pg 24 Space for Silica Gel Pg 24 11 Introduction Setting the Switches and the Lens TK C215VP4U E Set the video setting switches on the camera unit before mounting it To set the switches use a fine tipped screwdriver FOCUS ADJUST RESET SPOT RESET SPOT button When switch 8 is set to RESET position and this button is pressed the value of the white balance or phase adjusted manually is reset to the default value When switch 2 SELECT is set to WHT BAL the white balance is reset to the default value When the switch is set to PHASE the phase is reset to the default value When switch 8 is set to SPOT When this button is pressed white spots are corrected For instructions on correcting white spots see White spot correction rs Pg 34 R B R B adjustment button This button is pressed when manually adjusting the white balance or when adjusting the vertical phase of the line lock The function of this button is selected using the 2 SELECT switch When manually adjusting the white balance Press the R button to increase the red tint and decrease the blue tint Press the B button to increase the blue tint and decrease the red tint 12 Function Selection Switch Settings Chart Characters in bold indicate factory settings OFF m a ON
11. is used as a RESET button SPOT The RESET SPOT button is used as a SPOT button Pg 34 Default setting RESET IRIS LEVEL Iris level adjustment For adjusting the level of the automatic aperture control lens This adjustment only needs to be made when required Use this to accommodate particular shooting conditions To darken image Counterclockwise L side To brighten image Clockwise H side Memo e Prior to adjusting the aperture level ensure to set the AGC Switch 1 of the function selection switch to OFF Otherwise when the level is turned too far toward L the AGC function activates increasing sensitivity and the picture may look uneven FOCUS ADJUST focus adjustment button Use this to adjust the lens focus Upon pressing the lens aperture will open up for about 30 seconds such that the depth of field becomes shallower thus enabling focus to be easily adjusted Pg 26 Memo The electronic shutter functions automatically upon pressing the focus adjustment button and the screen may flicker However this is not a malfunction Q Focus adjustment ring Move this to the left right to adjust the focus Zoom adjustment ring Move this to the left right to adjust the field angle 13 Introduction Setting the Switches and the Lens TK C215VP12U E Set the video setting switches on the camera unit before mounting it To set the switches use a fin
12. the lens is at the alarm position the lens continues to remain in the alarm position for 15 seconds upon the last alarm input STATE Upon input of an alarm the lens moves to the preset zoom focus position alarm position The lens remains in the alarm position for 15 seconds The lens will after a lapse of 15 seconds continue shooting at the alarm position as long as there is alarm input The lens returns automatically to the home position immediately after alarm input stops Default setting TRIGGER 8 RESET SPOT RESET SPOT correction selection switch RESET The RESET SPOT button is used as a RESET button SPOT The RESET SPOT button is used as a SPOT button r amp Pg 34 Default setting RESET 15 Installation and Connection System Example Turn off the power of devices to be used before connecting the cables Read through the Instruction Manual of the devices to be used carefully before connecting Coaxial Cable TK C215VP4U E Power Cable Alarm Signal METAL CONTACT E Power Unit DC12 V or AC24 V Class 2 VIDEO INPUT Hard Disk Recorder etc VIDEO OUTPUT VIDEO INPUT Monitor Memo Note When mounting the heater sold separately Power consumption of TK C215VP4 TK part number KA ZH215 make sure to C215VP12 are different from one another connec
13. 768 H x 494 V E type 440 000 pixels 752 H x 582 V Sync system Line lock Internal Video S N 50 dB AGC OFF white 50 96 output Horizontal resolution 540 TV lines Center Typ Minimum illumination Typical TK C215VP4U Color mode 2 5 Standard AGC ON 50 IRE WIDE end 0 8 Ix Standard AGC ON 25 IRE WIDE end Black and White mode 1 4 Ix Standard AGC ON 50 IRE WIDE end 0 4 Ix Standard AGC ON 25 IRE WIDE end TK C215VP12U Color mode 3 5 Ix Standard AGC ON 50 IRE WIDE end 1 1 Ix Standard AGC ON 25 IRE WIDE end Black and White mode 2 0 Ix Standard AGC ON 50 IRE WIDE end 0 6 Ix Standard AGC ON 25 IRE WIDE end 36 TK C215VP4E Color mode 2 9 Ix Standard AGC ON 50 IRE WIDE end 0 9 Ix Standard AGC ON 25 IRE WIDE end Black and White mode 1 7 Ix Standard AGC ON 50 IRE WIDE end 0 6 Ix Standard AGC ON 25 IRE WIDE end TK C215VP12E Color mode 4 2 Ix Standard AGC ON 50 IRE WIDE end 1 3 Ix Standard AGC ON 25 IRE WIDE end Black and White mode 2 4 Ix Standard AGC ON 50 IRE WIDE end 0 8 Ix Standard AGC ON 25 IRE WIDE end White balance ATW Manual Switchable Color temperature range 2 300 K to 10 000 K Backlight compensation ON OFF Switchable Easy DAY amp NIGHT ON OFF Switchable Lens Focal length TK C215VPAU E 2 8 mm to 10 mm variable TK C215VP12U
14. FERENCE AND 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION Due to design modifications data given in this instruction book are subject to possible change without prior notice Introduction Safety Precautions continued Information for Users on Disposal of Old Equipment European Union This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end of life Instead the product should be handed over to the applicable collection point for the recycling of electrical and electronic equipment for proper treatment recovery and recycling in accordance with your national legislation By disposing of this product correctly you will help to conserve natural resources and will help prevent potential negative effects on the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more information about collection point and recycling of this product please contact your local municipal office your household waste disposal service or the shop where you purchased the product Attention This symbol is only valid in the European Union with national legislation Business users Penalties may be applicable for incorrect disposal of this waste in accordance If you wish to dispose of this product please visit our web pa
15. JVC DOME CAMERA TK C215VP4U E INSTRUCTIONS TK C215VP12U E For Customer Use Enter below the Serial No which is located on the body Retain this information for future reference Model No TK C215VP4U E TK C215VP12U E Serial No LST0519 001A Introduction These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances IMPORTANT SAFEGUARDS Read all of these instructions Save these instructions for later use All warnings on the product and in the operating instructions should be adhered to Unplug this appliance system from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp cloth for cleaning Do not use attachments not recommended by the appliance manufacturer as they may cause hazards Do not use this appliance near water for example near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool etc Do not place this appliance on an unstable cart stand or table The appliance may PORTABLE CART WARNING fall causing serious injury to a child or adult and serious damage to the appliance symbol provided by RETAC Use only with a cart or stand recommended by the manufacturer or sold with the appliance Wall or shelf mounting should follow the manufacturer s instructions and should use a mounting kit approved by the manufacturer An appliance and cart combination shou
16. LECTROCUTION NE PAS EXPOSER L APPAREIL A L HUMIDITE OU A LA PLUIE INFORMATION FOR USA INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CAUTION CHANGES OR MODIFICATIONS NOT APPROVED BY JVC COULD VOID USER S AUTHORITY TO OPERATE THE EQUIPMENT THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTER
17. Piping hole G3 4 14 UNC Note When screwing in the pipe make sure that not more than 12 mm 15 32 inch of the pipe is being screwed in Failure to do so may damage the internal components of this unit 6 Fastening the base to the ceiling Fasten the base to the ceiling firmly using 2 M4 mm screws Note 04 mm screws are not supplied with this product Use appropriate type of screw according to the material of the mounting place Check to ensure that there is no space between the ceiling and base 7 Mounting the fall prevention wire to a firm place c Pg 21 32 4 Sealing Tape cag s 12 5 32 inch and below B 94 mm screw 8 The following procedures are same as normal mounting Cable Connection rs Pg 22 Mounting the camera unit to the base Pg 23 Adjusting Images 1 Pg 25 Mounting the inner dome t Pg 30 Mounting the dome cover rs Pg 30 Mounting the camera using the piping hole at the side surface of the base If the camera cannot be mounted directly to the ceiling mount it to the pipe using the piping hole at the side surface of the base 1 Setting the switches t Pg 20 2 Dismantle the camera unit from the base and mount the fall prevention wire Pg 21 Pg 9 3 Binding the sealing tape Bind at least 2 layers of the sealing tape to the joint of the pipe point where the thread of the piping hole co
18. e tipped screwdriver LEVEL Ol ipowrsus w TELE j ARY MEM PT AR A ALARM POSITION Function selection switch setting table Items in bold are factory position OFF a 2 ON 1 AGC OFF ON 2 SELECT PHASE WHT BAL 3 SYNC LL INT 4 WHT BAL ATW MANUAL 5 BLC OFF ON 6 DAY NIGHT OFF ON 7 ALARM TRIGGER STATE 8 RESET SPOT RESET SPOT IRIS LEVEL Iris level adjustment For adjusting the level of the automatic aperture control lens This adjustment only needs to be made when required Use this to accommodate particular shooting conditions To darken image Counterclockwise L side To brighten image Clockwise H side Note Prior to adjusting the aperture level ensure to set the 1 AGC Switch of the function selection switch to OFF Otherwise when the level is turned too far toward L the AGC function activates increasing sensitivity and the picture may look uneven 14 ZOOM FOCUS MEMORY zoom focus adjustment switches position memory button Use the ATELE and WWIDE switches to zoom and the 4FAR and NEAR switches to adjust focus Pg 28 Press the MEMORY button to register the position Pg 28 ALARM POSITION status indication LED Light off Registration of home position is enabled Light on red Lens
19. einforcement of the ceiling or wall before installation The rating label is placed on the bottom surface of the camera unit The camera unit may fall if the mounting Screw or piping is not properly tightened Ensure that the screws and nuts are properly tightened We do not accept liability for any damage to the camera in cases when it is dropped because of incomplete installation due to not observing the installation instructions correctly Please be careful when installing the camera Do not install the camera near lighting equipment with a high temperature such as spotlights Doing so may cause malfunction or fire Thank you for purchasing this product These instructions are for TK C215VP4U TK C215VP4E TK C215VP12U TK C215VP12E Before beginning to operate this unit please read the instruction manual carefully in order to make sure that the best possible performance is obtained Characteristics Excellent dust proof and water proof performance With the dust proof and water proof structure it can be installed outdoor directly as it will not be affected by the rain IP66 specification Realizing a High Picture Quality This camera provides 540 TV lines with a S N ratio of 50 dB This performance is achieve by using a highly sensitive CCD with 380 000 pixels U type or 440 000 pixels E type and a high resolution video processing circuit Enlarged Shooting Range The adjustment
20. en the dome cover and base Failing to do so may cause the dust proof and water proof features to malfunction Mounting the camera using the electrical box Mounting the base to the electrical box 1 Setting the switches t Pg 20 2 Removing the camera unit from the base c Pg 21 3 Mounting the base to the electrical box Mount the base to the electrical box by using the 2 mounting holes and 2 M4 screws Memo M4 screws are not supplied with this product 4 Inch square electrical box M4 Screw 4 The following procedures are same as normal mounting Cable Connection Pg 22 e Mounting the camera unit to the base Pg 23 Adjusting Images rs Pg 25 e Mounting the inner dome c Pg 30 e Mounting the dome cover Pg 30 31 Installation and Connection Mounting the camera using the pipe Use the piping hole to mount the camera Mounting the camera using the piping hole at the bottom surface of the base 1 Setting the switches t Pg 20 2 Removing the camera unit from the base c Pg 21 step 1 3 Mount the fall prevention wire to the base Pg 21 4 Binding the sealing tape Bind at least 2 layers of the sealing tape to the joint of the pipe point where the thread of the piping hole coincides with the screw hole of the pipe 5 Mounting the base to the pipe Screw the base into the pipe by turning the base in the clockwise direction
21. ening screws The electronic shutter functions automatically upon pressing the focus adjustment button and the screen may flicker However this is not a malfunction Adjusting the brightness Usually adjustment of the brightness is not required When this is necessary adjust the iris level accordingly To darken Anti clockwise direction L side To brighten Clockwise direction H side Memo Do not perform iris level adjustment within 30 seconds after pressing the focus adjustment button It cannot be adjusted correctly as the electronic shutter mode is activated e Before adjusting the iris level set the AGC switch of selection switch to OFF If turning too much to L side when not set to OFF AGC feature will activate causing the sensitivity increases and the picture quality may appear grainy 27 Installation and Connection Adjusting the video image continued TK C215VP12U E 2 types of angle of view may be selected for TK C215VP12U E In general set in a way such that the home position shoots a wide range and the alarm position a narrow range Use the alarm input mode selection switch to set the actions when there is an alarm input c Pg 15 Registering home position For registering the angle of view during monitoring under normal conditions r E gr 50 2 EI i SUI 2 2 a Tw
22. ensation switch When the object is placed against the light setting this to ON increases the iris aperture by 1 stop and the object will appear brighter Default setting OFF 6 DAY NIGHT Easy DAY amp NIGHT switch To capture a subject with continually changing brightness day night set this switch to ON The camera automatically captures the image in color when the subject is bright and in black and white mode when it is dark Default setting OFF Note When this item is set to ON the AGC feature will automatically be set to regardless of the AGC Switch 1 setting The Easy DAY amp NIGHT feature on this camera uses a sensitized black and white mode unlike other black and white surveillance cameras that use infra red lighting e Sensitivity increases in the case of black and white images The screen may therefore appear rougher and white spots may increase 7 ALARM alarm input mode selection switch For setting the lens movement when there is an alarm input Set according to the alarm device that you are using pg 18 Electrical Specifications of Alarm Input Terminals pg 25 Adjusting the video image TRIGGER Upon input of an alarm the lens moves to the preset zoom focus position alarm position The lens remains in the alarm position for 15 seconds before it returns automatically to the home position When there is a new alarm input while
23. ers Specifications 36 Before starting an important recording be sure to perform a test recording in order to confirm that a normal recording is possible We will not provide any compensation whatsoever for the contents to be recorded or loss of opportunities when recording is not properly performed due to malfunction of the video camera VTR hard disk recorder or video tape Before touching the camera unit make sure to touch the metal surface of the MONITOR terminal to discharge any static electricity from your body Static electricity may cause the camera to malfunction Precautions for proper use of this product Storage and Location of Use Do not install this unit at the following locations Places that are exposed to vapor or oil such as kitchens Places that exceed the ambient temperature range 10 C to 50 Places at which corrosive gases are emitted Places where radiation or X rays and strong radio waves or magnetism are present Places that are subject to vibration Using this unit or cables connected to this unit in places where strong radio waves and magnetic fields are present e g near a radio TV transformer or motor may increase the noises in the image and color changes Do not install this unit at a place that is directly exposed to cold air or near the outlet of an air conditioner The dome cover may become foggy when there
24. exeers t FGPG POSITION ALARM 1 Check that the ALARM POSITION indicator light is turned off Registration of home position is enabled Press the POSITION SELECT button if the ALARM POSITION indicator light is on 2 Adjust the angle of view Adjust the field angle Move the zoom adjustment switch in the TELE or WIDE direction to adjust the field angle Adjust the focus Move the focus adjustment switch in the NEAR or FAR direction to adjust the focus Note When the ZOOM FOCUS switch is set to either TELE WIDE or NEAR FAR the iris will automatically open up for about 30 seconds and focus can be easily adjusted During this interval the electronic shutter mode is activated and the image may flicker However this is not a malfunction 28 3 Press the MEMORY button for 2 seconds or longer The ALARM POSITION indicator light blinks for 3 times green 4 Adjust the brightness This adjustment only needs to be made when required Use this to accommodate particular shooting conditions To darken image Counterclockwise L side To brighten image Clockwise H side Note e For adjusting the brightness do not conduct it within 30 seconds after pressing the ZOOM FOCUS button e When adjusting the iris level set the AGC switch to OFF Otherwise when the level is turned too far toward L the AGC function activates increasing sen
25. fastening screw for the fall prevention wire and mount the fall prevention wire Note Pay attention to the length strength routing and material insulation properties of the fall prevention wire used The internal diameter of the rounded portion on the camera unit to which the fall prevention wire is to be mounted shall be at least 4 1 mm and not larger than 6 5 mm and its external diameter shall not be larger than 212 mm 3 Mounting the fall prevention wire to a firm place To prevent the camera from falling mount the base to a firm place using the fall prevention wire 4 Mounting the base Mount the base by aligning the shooting direction mark on the inner side of the base 1 to the shooting direction When mounting to the wall mount it with the shooting direction mark 9 facing upward Do so by using 2 24 mm mounting screws Note When mounting to the wall make sure to mount it with the shooting direction mark 4 facing upward Failure to do so may cause the fall prevention wire of the dome cover to come off easily 04 mm screws are not supplied with this product Use appropriate type of screw according to the material of the mounting place Fall Prevention Wire Base Align with shooting V direction Face upward when B 94 mm screw mounting to the wall 21 Installation and Connection Cable Connection 1 Connecting the coaxial cable c Pg 17 Lower the p
26. ge www jvc europe com to obtain information about the take back of the product Other Countries outside the European Union If you wish to dispose of this product please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment Dear Customer This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety European representative of Victor Commany of Japan Limited is JVC Technology Centre Europe GmbH P O Box 10 05 52 61145 Friedberg Germany The unit is to be powered by a DC 12 V AC 24 V power supply The unit is to be powered by a UL Listed DC 12 V or an AC 24 V power supply For U type The AC 24 V and 12 V DC power supply shall conform to the following Class 2 only For USA Isolated power supply only For Europe This installation should be made by a qualified service person and should conform to all local codes This installation shall be in accordance with the National Electrical Code ANSI NFPA 70 4 Any Mention in this manual ot Alarm inputs have not been evaluated by UL to be used for Burglar Alarm Functionality When mounting this unit to the ceiling or wall mount it to a secure location where it can support the mass of this unit When mounting to an insecure location make sure to carry out r
27. ill be reset The camera switches to the same mode as with pressing the RESET button Default setting ATW Memo e The white balance of this camera is preset to use under sunlight or halogen lamps and may not be properly adjusted when used under artificial lights such as fluorescent lights 5 BLC Backlight compensation switch When the object is placed against the light setting this to ON increases the iris aperture by 1 stop and the object will appear brighter Default setting OFF 6 DAY NIGHT Easy Day amp Night switch To capture a subject with continually changing brightness day night set this switch to ON The camera automatically captures the image in color when the subject is bright and in black and white mode when it is dark Default setting OFF Memo When this item is set to ON the AGC feature will automatically be set to regardless of the AGC Switch 1 setting The Easy DAY amp NIGHT feature on this camera uses a sensitized black and white mode unlike other black and white surveillance cameras that use infra red lighting Sensitivity increases in the case of black and white images The screen may therefore appear rougher and white spots may increase 7 RESERVED Not used Ensure to set this to OFF before using the camera Default setting OFF 8 RESET SPOT RESET SPOT CORRECTION selection switch RESET The RESET SPOT button
28. incides with the screw hole of the pipe Sealing Tape 4 Removing the plug for the piping hole of the base Loosen the mounting screw M3 x 6 mm using a slotted screwdriver and pull out the plug at the side of the base Plug for Piping Hole Mounting Screw 5 Mounting the removed plug for the piping hole to the piping hole at the bottom surface of the base 6 Mounting the base to the pipe Screw the pipe into the piping hole at the side of the base Piping hole G3 4 14 UNC Note When screwing in the pipe make sure that not more than 12 mm 15 32 inch of the pipe is being screwed in Failure to do so may damage the internal components of this unit Plug for Piping Hole N T The following procedures are same as normal mounting Cable Connection rs Pg 22 Mounting the camera unit to the base Pg 23 Adjusting Images 1 Pg 25 Mounting the inner dome t Pg 30 Mounting the dome cover t Pg 30 33 Installation and Connection White spot correction As a general characteristic unique to CCDs white spots may appear on the screen with age In order to reduce this phenomenon this unit is equipped with a white spot correction feature Switch on the camera power supply and wait for at least 30 minutes TK C215VP4U E reso SPOT button Function selection switch 8 TK C215VP12U E S SPOT button F
29. initializing Light on green Registration of alarm position is enabled Blinking green Position memory registration mode memory registration completed c Pg 28 POSITION SELECT POSITION SELECT button Press this button to switch between the home and alarm positions Display on the status indication LED will change accordingly c Pg 28 RESET SPOT RESET SPOT button When switch 8 is set to RESET position and this button is pressed the value of the white balance or phase adjusted manually is reset to the default value When switch 2 SELECT is set to WHT BAL the white balance is reset to the default value When the switch is set to PHASE the phase is reset to the default value When switch 8 is set to SPOT When this button is pressed white spots are corrected For instructions on correcting white spots see White spot correction Pg 34 R B R B adjustment button This button is pressed when manually adjusting the white balance or when adjusting the vertical phase of the line lock The function of this button is selected using the 2 SELECT switch e When manually adjusting the white balance Press the R button to increase the red tint and decrease the blue tint Press the B button to increase the blue tint and decrease the red tint When adjusting the phase Press the or button to adjust the phase Function selection switche
30. ion TK C215VP4 U type 42W 23 W When using KA ZH215 E type 940 mA 1 A When using KA ZH215 TK C215VP12 U type 6 6 W 24 W When using KA ZH215 E type 550 mA 1 A When using KA ZH215 37 Others Specifications continued E Dimensional Outline Drawing Unit mm inch 121 4 3 4 T 113 4 1 2 for piping bottom surface side surface 160 6 1 4 Specifications and appearance of this unit and related products are subject to change for product improvement without prior notice 38 Focus chart 39 2006 Victor Company of Japan Limited VHaNWvo 3Woga J NZLdASLZO AL LST0519 001A J NtdASLZO AL
31. is a drastic change in temperature Although this unit is IP66 compliant water proof under all kinds of environment is not guaranteed Others This unit comes with a built in AGC circuit When the AGC function is turned on the sensitivity increases automatically at a dark place and the screen may appear grainy This is not a malfunction When using the Automatic Tracking White balance ATW mode the color tone may differ slightly from the actual color This slight color variation is caused by the principle of Auto Tracking White balance circuit and is not a camera malfunction When shooting an object with high brightness lamps etc vertical lines may appear in the image on the screen smear phenomenon and bleeding may be found around the high brightness object blooming phenomenon These are due to the characteristics of the CCD and not malfunctions Turning ON DAY amp NIGHT function switches the image to black and white in a dark place When switching between colored and black and white images the bright portions of the screen are enhanced and the clarity of the screen may deteriorate Overall the sensitivity increases in the case of black and white images therefore the scene may appear grainy and white spots may become visible This is not a malfunction When the power source voltage drops such as during lightning or upon turning on the air conditioner distortion or noise may occur in the image
32. ith sealing material Fill the piping hole as well as the 2 mounting holes mounted with screws using a sealing material D Use GE silicon or its equivalents as the sealing material Note e If the piping hole and the 2 mounting holes mounted with screws are not filled with sealing material completely water or vapor may enter the holes causing the lens and dome cover to fog Make sure that these holes are completely filled 2 Mounting the camera unit to the base Press the 2 clips until a click sound is heard Note Mount such that the cables and fall prevention wire of the dome cover are not clamped 3 Fastening the 2 fastening screws of the camera unit Tighten the 2 fastening screws of the camera unit using a screwdriver to fasten the camera 2 TK C215VP4U E is used in the above illustration 23 Installation and Connection Mounting the camera unit continued 4 Inserting the silica gel supplied Take out the silica gel from the aluminum package insert it into the silica gel insertion space of the camera unit and fasten using the 2 MEET iY 2 p Silica Gel fire NN T TK C215VP4 is used in the above illustration Memo During reconnection or re installation after repair or maintenance make sure to replace the silica gel with a new one Consult your nearby JVC s dealer on the
33. ld be moved with care e Quick stops excessive force and uneven surfaces may cause the appliance and cart combination to overturn 8 Slots and openings in the cabinet and the back or bottom are pro vided for VA ES ventilation and to insure reliable operation of the appliance and to protect it from 53125 overheating these openings must not be blocked or covered The openings should never be blocked by placing the appliance on a bed sofa rug or other similar surface This appliance should never be placed near or over a radiator or heat register This appliance should not be placed in a built in installation such as a bookcase unless proper ventilation is provided 9 This appliance should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supplied to your home consult your dealer or local power company For appliance designed to operate from battery power refer to the operating instructions 10 For added protection for this product during a lightning storm or when it is left unattended and unused for long pene of time unplug it form the wall outlet and disconnect the antenna or cable system This will prevent damage to the product due to lightning and power line surges 11 Do not allow anything to rest on the power cord Do not locate this appliance where the cord will be abused by persons walking on it 12 Follow all warnings and instructions marked on the appliance 13
34. onnection About Connection Cables continued Electrical Specifications of Alarm Input Terminals TK C215VP12U E only To prevent penetration of noise in the internal circuitry apply a non voltage contact signal to the ALARM input terminal Never apply a voltage Apply an alarm signal for at least 200 ms If it is shorter it is not guaranteed that the signal will be recognized as an alarm signal e Under the alarm status status when the metal contact is make select the contact or connecting wire such that the maximum wire resistance between the ALARM IN and ALARM GND is within 150 ALARM IN ALARM GND Q Polarity of alarm signals ALARM INPUT SHORT CONTACT ALARM OPEN NORMAL HOME POSITION 18 The right sequence to Set the switches connect and set the camera Pg 20 step 1 Remove the dome cover followed Follow the procedures below to connect set this by setting the video image unit switches Turn off the power of devices to be used before v connecting the cables Mounting the base Before touching the camera unit make sure to touch the metal surface of the step 2 5 toth MONITOR terminal to discharge any Coh Ease e Wa or static electricity from your body Static 9 electricity may cause the camera to v malfunction When mounting the base to the ceiling or Connect the cable when connecting the cable of the came
35. ot supplied with this product Note Connect the fall prevention wire to prevent this unit from falling accidentally The camera unit may fall if this wire is not connected Dome Cover Inner Dome Set the switches as well as angle of view before mounting the camera rs Pg 20 Q Plug for Piping Hole and Piping Hole Side Use this plug when mounting directly to pipes from the side The plug for piping hole is mounted to this hole by default Pg 33 Introduction Name of Parts continued Camera continued Base Mount the base to the ceiling wall or electrical box before mounting the camera Pg 21 r amp Pg 31 Fastening Screw for Dome Cover This is a fastening screw for the dome cover Use a supplied wrench to fasten unfasten the Screw AC 24 V DC 12 V Power Supply Wire DC 12 V Input Red 12 V Black GND AC 24 V Input Nonpolar Note In order to use the optional heater unit sold separately part number KA ZH215 with this camera an AC 24 V power supply MUST be use The AC 24 V power supply should conform to the following U type Class 2 only E type Isolated power supply only For inquiries on the heater consult your nearby JVC dealer 10 Alarm signal cable TK C215VP12U E only Yellow ALARM IN Gray ALARM GND c Pg 18 Protection Cover Upon connecting the video cable please protect the BNC connection using this rubber co
36. ra ensure that the pan fastening screw is loosened Moving the lens unit without loosening the pan fastening screw may damage the lens unit f anning A A Rotation 175 Tilting 70 TK C215VP4U E is used in the above illustration Camera s shooting direction mark pr om gt Pan center mark D B ES AN Rotation center mark Rotation knob TK C215VP4U E only Always adjust the rotation by holding this knob Memo e Panning rotation of 175 is possible from each of the camera unit s shooting direction mark pan center mark and rotation center mark When adjusting the rotation do not hold the lens unit Always adjust by holding the rotation knob When using the camera at locations with strong vibration after the angle of view is adjusted stabilize by tightening the tilt fastening screw to prevent the camera s angle of view from going out of alignment gt Pg 11 Note Moving the camera beyond its adjustable range may cause failure in maintaining the performance of this camera As this camera has a wide tilt rotation range a part of this camera may appear on the screen depending on the angle of view and orientation Do not hold the lens unit when adjusting the direction of the camera Applying force on the lens unit may damage it 25 Installation and Connection Adjusting the video image continued Adjusting the angle of view focus
37. ra rs Pg 22 unit pay enough attention to the fall of step 3 each part When mounting the heater sold separately KA ZH215 read the v instruction manual of the heater carefully before mounting Connect the coaxial cable and power supply for the heater Mounting the camera unit Pg 23 step 4 Fill the piping hole and screw hole with a sealing material followed by mounting the camera unit to the base wv Adjusting the video image step 5 Pg 25 Adjust the camera s angle focus and brightness v Mounting the inner dome step 6 rs Pg 30 After setting is complete mount the inner dome to the camera wv Mounting the dome cover Pg 30 Insert the silica gel into the step 7 designated space to prevent fogging of the dome cover followed by mounting the dome cover 19 Installation and Connection Setting the switches Remove the dome cover followed by setting the video image switches 1 Removing the dome cover Remove the dome cover by unfastening the 3 fastening screws using the wrench supplied Memo The dome cover and base are connected with fall prevention wire Wrench Supplied Fall Prevention Wire TK C215VP4U E is used in the above illustration 2 Removing the inner dome The inner dome is fastened using clips at 3 different positions Grasp the inner dome and remove it from the clips Note Befo
38. range of the shooting direction is wide and mounting of the camera to the wall is possible with the employment of 3 axis rotation mechanism ll Non Camera Like Design Dome type design allows application in various locations High Magnification Varifocal Zoom Lens The built in x3 6 varifocal lens TK C215VP4U E and x12 zoom lens TK C215VP12U E enables detailed supervision Alarm Zoom Feature TK C215VP12U E only 2 preset positions are available which allow setting of the monitoring screen size under normal circumstances and during alarm input Easy DAY amp NIGHT Feature This camera has an Easy Day amp Night function This function if activated will automatically switch to B amp W image when the scene is getting dark This is very useful for monitoring a dark environment This instruction manual covers total 4 different models in common as follows TK C215VP4U TK C215VP4E TK C215VP12U TK C215VP12E In this manual each model number is described without the last letter U E which means the shipping destination U NTSC E PAL Only U models TK C215VP4U TK C215VP12U have been evaluated by UL How to Use This Manual Characters and symbols used in this manual Note Points to pay attention to during operation Memo Details for reference such as functions or constraints during use Pages or items to refer to All product names that appear in this document are
39. re touching the camera unit make sure to touch the metal surface of the MONITOR terminal to discharge any static electricity from your body Static electricity may cause the camera to malfunction 20 3 Setting the switches Set the switches for video images v Pg 12 Setting the Switches and the Lens TK C215VPA4U E J v Pg 14 Setting the Switches and the Lens TK C215VP12U E J Clip x 3 4 Wit aL 2 Cal 4 x iH TK C215VP4U E is used in the above illustration Mounting the base Remove the camera unit from the base and mount the base to the ceiling or wall When mounting to a wall follow the procedures by replacing areas indicated as ceiling by wall accordingly Setup Drill mounting holes 230 mm 1 1 8 inch using the template supplied when necessary 030 mm 1 1 8 inch 100 37 8 inch Coaxial Cable moe Some E r Power Supply Wire Alarm Signal Cable 24 V only when heater HEREDES is in use TK C215VP12U E only 1 Removing the camera unit from the base D Unfasten the 2 fastening screws from the camera unit using a screwdriver Press the 2 clips inwards to remove the camera unit from the base Clip x 2 TK C215VP4U E is used in the above illustration 2 Mounting the fall prevention wire to the base fall prevention wire is not supplied Remove the
40. replacement procedures Serial number of part to be replaced Use a LW40500 001A silica gel Note When mounting is performed on a rainy day make sure that rain water does not enter this unit e Make sure to use the silica gel supplied Failure to do so may cause the camera lens and dome cover to fog e If the angle of view is not adjusted immediately after mounting the camera insert the silica gel after adjustment is completed The silica gel loses its effect if it is exposed to the air for a prolonged period of time 24 Adjusting the video image Upon mounting the camera adjust the images while checking the actual image Mounting the test monitor Connect the MONITOR terminal of this unit to the test monitor to adjust the camera s shooting direction angle of view and focus Memo Before setting ensure to turn on the power of the system MONITOR Terminal 75 Q terminal Test Monitor TK C215VP4U E is used in the above illustration Adjusting the shooting direction of the camera The camera unit can be panned tilted or rotated Adjust the camera in the direction of the object Note Before touching the camera unit make sure to touch the metal surface of the MONITOR terminal to discharge any static electricity from your body Static electricity may cause the camera to malfunction e Before adjusting the shooting direction of the came
41. rotection cover and connect the connectors Upon connecting cover the connectors using the protection cover 2 Connecting the AC 24 V DC 12 V power supply wires Note To mount a heater sold separately to this unit make sure to connect it to an AC 24 V supply during use 3 Connect the alarm cable TK C215VP12U E only r Pg 18 4 Binding the AC 24 V DC 12 V power supply wires and alarm signal wires TK C215VP12U E only with insulating tape Make sure to bind the connecting portions of AC 24 V DC 12 V power supply wires and alarm signal wires TK C215VP12U E only with insulating tape 5 Wrap insulation tape around cables 6 Storing cables Upon connecting push the connector into the cable storage space of the camera unit Note When mounting the camera to the electrical box push the connector into the electrical box While the camera unit is disconnected from the base be extremely careful not to drop the camera unit 22 aum Bind insulating Protection Cover tape Coaxial Cable 24 VIDC 12 V Power Supply Wire Alarm signal Wire TK C215VP12 only Cx Cable Storage p d Space TK C215VP12U E is used in the above illustration Mounting the camera unit Fill the piping hole and mounting hole with a sealing material mount the camera unit to the base and insert the silica gel 1 Fill the hole w
42. s 1 AGC Auto gain control switch Setting this switch to ON automatically increases the sensitivity even when the brightness of the subject is insufficient Default setting ON 2 SELECT WHT BAL PHASE setting switch WHT BAL The R B buttons are used as R B adjustment buttons PHASE The R B buttons are used as adjustment buttons Default setting WHT BAL 3 SYNC Synchronization system selection switch This switch sets the synchronizing system for the camera INT This is set for internal synchronization LL Line Lock The camera s vertical synchronization is locked to the AC 24 V power line frequency When switching between multiple cameras using a switcher selecting this mode and adjusting the vertical phase can reduce the monitor sync disturbances occur that when the camera image is switched U type 60 Hz only E type 50 Hz only Default setting INT 4 WHT BAL ATW MANUAL selection switch For selecting whether to adjust the white balance automatically or manually When the setting is changed from manual to ATW the setting values in the manual mode will be reset The camera switches to the same mode as with pressing the RESET button Default setting ATW Note The white balance of this camera is preset to use under sunlight or halogen lamps and may not be properly adjusted when used under artificial lights such as fluorescent lights 5 BLC Backlight comp
43. sitivity and the picture may look uneven X Home position registration is completed Registering alarm position For registering the angle of view during monitoring when there is an alarm input 5 2 3 R amp ws EO 3 4 2 HA 85 E 2 4 L250 ms E 25 Tu Hi S v Cw e 1118 8 40 1 5 1 Check that the ALARM POSITION indicator light is turned on Registration of alarm position is enabled Press the POSITION SELECT button if the ALARM POSITION indicator light is off 2 Adjust the image size r Pg 28 3 Press the MEMORY button for 2 seconds or longer The ALARM POSITION indicator light blinks for 3 times green X ALARM position registration is completed 4 Adjust the brightness t Pg 28 5 Press the POSITION SELECT button The camera returns to the home position Note Be sure to return the camera to the home position after registration of the alarm position is completed In addition to pressing the POSITION SELECT button you can also use the power ON OFF button to return the camera to the home position To check images at the registered home position or alarm position press the POSITION SELECT button Press this button to switch between the image at the home and alarm positions 29 Installation and Connection Mounting the inner dome
44. t the power wire to an AC 24 V power When installing a mixture of these models supply only select a cable length according to the power The AC 24 V power supply should conform to consumption of each model Alternatively the following install based on the model with the highest U type Class 2 only power consumption E type Isolated power supply only 16 About Connection Cables The maximum connection distance varies with the type of cable used Please refer carefully to the table for each cable during connection Be sure to turn off the power of devices before connecting cables To video Signal 14 Cable To DC 12 V or AC 24 V Power Supply Note DC 12 V or AC 24 V power supply cable Connect the DC 12 V or the AC 24 V power supply to the DC 12 V AC 24 V terminals on the terminal board To prevent connection errors or a cable disconnection we recommend the use of lug plates for the connections The following table shows the connection distances and connection cables provided that 2 conductor VVF cables vinyl insulated vinyl sheath cables are used Conductor diameter mm 1 0 mm 1 6 mm 92 0mm AWG18 AWG14 AWG12 When mounting the heater sold separately part number KA ZH215 make sure to connect the power wire to an AC 24 V power supply only Video signal cables Connect the coaxial cables BNC to the video signal output connector BNC
45. the trademarks or registered trademarks of their respective companies Marks and symbols such as and do not appear in this document Introduction Table of Contents Introduction Safety Precautions 9 Characteristics Table of Contents 6 Precautions for proper use of this product 7 Name of Parts 9 Setting the Switches and the Lens TK C215VP4U E 12 Setting the Switches and the Lens TK C215VP12U E 14 Installation and Connection System Example 16 About Connection Cables 17 Video signal cables 17 DC 12 V or AC 24 V power supply cable 17 Electrical Specifications of Alarm Input Terminals 18 The right sequence to connect and set the CAMOMA eee nee Setting the switches Mounting the base Cable Connection Mounting the camera unit Adjusting the video image Mounting the inner dome Mounting the dome cover Mounting the camera using the electrical box 31 Mounting the camera using the pipe 32 White spot correction 34 Oth
46. unction selection Switch 8 IRIS SN LEVEL WATBAL OF VOR C B U TF amp 5 RESET E POT position ZOOMFOCUS FAR A TEE gt AR Y e MEMORY SELECT WIDE 4 NE ALARM POSITION 34 1 Remove the dome cover 2 Cover the lens surface using a black sheet of paper etc so that light does not enter the lens 3 Set the function selection switch 8 to SPOT c Pg 13 4 Press and hold the SPOT CORRECTION button for more than 2 seconds White spot correction will start Correction may take several seconds for completion Memo Maximum correction 32 The white spot correction feature of this unit does not guarantee the correction of all white spots Depending on the characteristic of white Spots correction may not be possible When performing white spot correction accurate data may not be achieved in case of highly detailed pixels since correction is made using the information of surrounding pixels The result of white spot correction is maintained until the next correction is performed 35 Others Specifications E Camera Signal system U type Based on NTSC standard E type Based on PAL standard Scanning frequencies U type 15 734 kHz Horizontal 59 94 Hz Vertical E type 15 625 kHz Horizontal 50 Hz Vertical Image device 1 4 IT CCD Effective picture elements U type 980 000 pixels
47. ver Video signal output connector BNC c Pg 17 Camera Interior TK C215VP4U E is used in the above illustration B Rotation Knob TK C215VP4U E only Rotate the lens unit to adjust the inclination of the image rs Pg 25 Rotation Center Mark Pg 25 D Fall Prevention Wire Use this to connect the base to the dome cover D Camera Unit Fastening Screw x 2 Use this fasten the camera body to the base To remove t Pg 21 MONITOR Monitor Terminal RCA Jack Pg 25 D Camera Unit D Connector for Power Supply of Heater This is a power connector for use when the heater sold separately KA ZH215 is mounted Space for Heater Memo When mounting the heater sold separately KA ZH215 read the instruction manual of the heater carefully before mounting Lens next page Camera Unit Fastening Clip x 2 This clip is used for fastening the camera unit to the base When removing the base press toward the direction indicated by the arrow to release c Pg 21 Tilt Fastening Screw Upon adjusting the angle of view tighten the screw to ensure that camera s angle of view does not go out of alignment when it is used at a location with strong vibration Pg 25 Shooting Direction Mark Install the camera by aligning the shooting direction with the arrow mark Lug Plate This plate is used for
Download Pdf Manuals
Related Search