Intellinet 524957 router
Contents
1. E ROUTER SETUP NETWORK SOLUTIONS 3 6 Firewall This series of submenu options lets you establish a variety of network usage and access limits for better control and security 3 6 1 Firewall Options Quick Setup Admin WAN LAN NAT Firewall Routing Qos Firewall Options Client Filtering URL Filtering MAC Filtering Settings Enabled K Options k k Discard PING From WAN side IP Spoofing L lt Deny PING to the Gateway Smurf Attack K x Detection Port Scan Packets Ping of Death k k Deny to Scan Security Port 1137 Land Attack K Discard NetBias Packets Snork Attack s Deny Fragment Packets UDP Port Loop ODO K Disable ICMP Packets When Error is TCP Null Scan E Encountered L TCP Syn Flood Syn Threshold packets per second 1 3000 ICMP Flood F Ping Threshold packets per second 1 3000 Cancel Enabled Select to enable disable the items selected or the limits established in the Options table 3 6 2 Client Filtering This screen allows you to block Internet access for local clients based on IP addresses application types and time of day Enable Client Filter Select to enable disable the function ROUTER SETUP VY INTELLINET NETWORK SOLUTIONS Firewall Options Client Filtering URL Filtering MAC Filtering Settings Enable Client Filter Enable IF Address 197 168 2 Type Block Time O always Block Day2. Settings This section displays the logs of various activites and events and also allows you to send these records to another location via e mail ROUTER SETUP GINTELLINET NETWORK SOLUTIONS SMTP Server Enter the address of the Simple Mail Transfer Protocol server that will be used to send the log information Sender Receiver Email Address Enter the addresses that logs will be sent from to then select Email Log and click Send 3 2 8 Logout Click OK to log out from the Web 3 3 WAN As mentioned in Section 3 1 Quick Setup this menu presents details about the numerous options available in the four connection types you can choose from Dynamic IP Address Static IP PPPoE and BigPond Quick Setup Admin WAN LAN NAT Firewall Routing Qos Misc F WAN Mode WAM Connection Mode Dynamic IP Address Obtain an IP address automatically From your service provider Use a static IP address Your service provider gives a static IP Static IP address to access Internet services PPPOE PPP over Ethernet is common connection method used For xDSL BigPond Australia ISP service 3 3 1 Dynamic IP Address Make this selection in the WAN Connection Mode panel to obtain an IP address from your Internet service provider ISP automatically ISPs that supply a cable modem always use this Request IP Address If your ISP supports this function you can enter an IP address you would prefer MTU M
3. PWR This lights when the router is turned on 4 1 These correspond to the four LAN ports on the router s rear panel Lighted indicates a successful connection blinking means data is being transmitted or received through that port WAN Lighted indicates a successful Internet connection blinking indicates data is being transmitted or received through that port 2 NETWORK SETTINGS To configure the router using a Web browser based configuration utility at least one properly configured computer needs to be connected to the router via the Ethernet This 4 Port Broadband Router is configured with the default IP address of 192 168 2 1 and subnet mask of 255 255 255 0 and its DHCP server is enabled by default At this point you can proceed to Section 2 3 Logging In to the Web Browser If you encounter problems from there return here and follow the steps in Sections 2 1 IP Address Setup and 2 2 Confirming the Connection 2 1 IP Address Setup 2 1 1 Windows 98SE Me 1 On your PC s desktop click Start and go to the Control Panel 2 Double click the Network icon to display the Network dialog box 3 Click the Configuration tab and ensure that you have the appropriate network card installed 4 Select TCP IP NOTE If TCP IP is listed more than once select INTELLINET ETW OR K SOLUTIONS NETWORK SETTINGS ee a the item that has an arrow pointing to the network card in
4. 3 7 2 Static Routing A static route is a pre determined pathway that network information must travel in order to reach a specific host or network Quick Setup Admin WAN LAN NAT Firewall Routing Qo5 Misc I Routing Table Static Routing Dynamic Routing Static Routes Configuration Destination Network IP Subnet Mask Gateway IP Destination Network IP Specify an address you want information packets forwarded to Subnet Mask Specify a subnet mask to distinguish the network and host portions of the IP address Gateway IP Enter the gateway IP address 3 3 Dynamic Routing Dynamic routing can be used to cache routes learned by routing protocols thus allowing the automation of static routing maintenance The router using RIP Routing Information Protocol determines a network packet s route based on the fewest number of hops between the source and the destination NOTE The RIP function is available only when the WAN connection mode is designated as either Static IP or Dynamic IP Address see Section 3 3 WAN Enable Dynamic Routing Select to enable disable the function ROUTER SETUP VY INTELLINET NETWORK SOLUTIONS Working Mode Select Routing Table Static Routing Dynamic Routing Router or Default Gateway oo Listen Mode Select ee Disabled RIP1 RIP or Both Working Mode Router RIP1 amp 2 Listen Mode Disabled Su pply Mode Select Supply Mode Disabled Di
5. Detect ROUTER SETUP OINTELLINET NETWORK SOLUTIONS Quick Setup Admin WAN LAN MAT Firewall Routing Hos Wizard WAN Mode Specify the WAN connection type required by your Internet Service Provider Please select your WAN connection from the following Auto Detect O Manual Select Auto detect result Detect or you can select Manual Select which presents you with four options Select one and click Next or click Back to return to the previous screen NOTE Additional configuration options for each of these four connection types are explained in detail in Section 3 3 WAN Quick Setup Admin VAN LAN MAT Firewall Routing Qos Misc Wizard WAN Mode Specify the WAN connection type required by your Internet Service Provider Please select your WAN connection from the following C Auto Detect Manual Select O Dynamic IP Address Static IP PPPOE O BigPond wl NTELLINET ETW OR K UTIONS ROUTER SETUP Dynamic IP Address This connection type means you obtain an IP address from your Internet service provider ISP automatically ISPs that supply a cable modem always use this Click Next to advance to the next screen Quick Setup Admin WAN LAN MAT Firewall Routing Wizard DHCP Mode Mac Cloning Mac Address Clone MAC N0O 00 00 00 00 00 Clone MAC Clone MAC The WAN port of the router has a unique Media Access Control
6. e LAN 1 4 Link Act Environmental e Dimensions 155 W x 85 L x 35 H mm 6 1 x 3 3 x 1 4 in e Weight 0 41 kg 0 9 Ibs e Operating temperature 0 40 C 32 104 F e Operating humidity 10 95 RH non condensing e Storage temperature 40 70 C 40 158 F Power e External power adapter 9 V DC 500 mA Package Contents e 4 Port Broadband Router e RJ45 Ethernet cable 1 0 m 3 ft e Power adapter e Quick install guide plus user manual on CD NTELLINET ETW OR K SOLUTIONS SPECIFICATIONS wl WASTE ELECTRICAL amp ELECTRONIC EQUIPMENT Disposal of Electric and Electronic Equipment applicable in the European Union and other European countries with separate collection systems This symbol on the product or its packaging indicates that this product X shall not be treated as household waste Instead it should be taken to an applicable collection point for the recycling of electrical and electronic BE equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences to the environment and human health which could otherwise be caused by inappropriate waste handling of this product If your equipment contains easily removable batteries or accumulators dispose of these separately according to your local requirements The recycling of materials will help to conserve natural resources For more detailed information about recycling of this p
7. 00 32 10 00 40 02 interface is displayed LAN MAC Address 00 32 10 00 AD 01 Host Name The Host Name is the name of the router IP Address Subnet Mask and Default Gateway The Internet IP Address Subnet Mask and Default Gateway IP GINTELLINET NETWORK SOLUTIONS ROUTER SETUP 3 ROUTER SETUP With the user interface displayed you have the option of proceeding with the Quick Setup procedure Section 3 1 below or selecting any of the 10 additional menu options Admin WAN etc Sections 3 2 3 11 which allow you to modify the default settings to customize your router and network configuration 3 1 Quick Setup The Quick Setup Wizard will guide you through the initial configuration of the router It s best that you follow the Quick Setup Wizard step by step 1 Enter an easily recognized remembered name for the router in the Host Name field then select a time zone from the drop down menu Enabling and configuring the Daylight Saving settings is optional Click Next Quick Setup Admin WAN LAN MAT Firewall Routing Hos Misc Hii Wizard HOST Settings 7 Host Name intelinet_router Daylight Saving Jenabled From i Time Zone FSMT 05 00 Eastern Time US ie Canada E 2 Specify the WAN wide area network connection type required by your Internet service provider You can select Auto Detect which will display the connection type in the Result field when you click
8. MAC address assigned to it referred to as Default MAC The Clone MAC option is available for special situations for example since an ISP allows only certain MAC addresses access to the Internet selecting MAC Address and clicking Clone MAC modifies your WAN port s MAC address in order to avoid detection of the router which can lead to a service disconnect Static IP This connection type allows you to maintain the same IP address over time unlike temporary dynamic IP addresses that are assigned with each Internet connection Click Next to Quick Setup Admin VAN LAN MAT Firewall Wizard WAN Static IP IP Address 0 0 0 0 Som we eee ee Subnet Mask Gateway IP ROUTER SETUP VY INTELLINET NETWORK SOLUTIONS advance to the next screen IP Address Enter the address provided by your ISP Subnet Mask Enter the address provided by your ISP Gateway IP This is provided by your ISP PPPoE This connection type Point to Point Protocol over Ethernet is typically used with DSL and ADSL service Click Next to advance to the next screen Quick Setup Admin VAN LAN MAT Firewall i Wizard PPPOE Mode User Name Password Retype password Service Name MTU 546 1492 or Maximum Idle Time 60 3600 300 seconds OD Mo timeout User Name Enter the PPPoE user name provided by your ISP Password Enter the PPPoE password provided by your ISP Retype Password F
9. ONS server addresses Advanced 7 When Local Area Connection Properties displays again click Close Local Area Connection Properties General Authentication Advanced Connect using B Intel R PROA00 VM Network Connection This connection uses the follovang tems al SU eee ee SJ Fie and Printer Sharing for Microsoft Networks Oos Packet Scheduler Wi 4 nemet Protocol TCRAP D senpior Allows pour computer bo access toucas on Microsoft nelak C Show icon in notification area when connected GINTELLINET NETWORK SOLUTIONS NETWORK SETTINGS 2 1 4 Windows Vista 7 1 On your PC s desktop click Start and go to the Control Panel 2 Click Network and Sharing Center gt Control Panel Name Category Control Panel Home BOR Administrat AutoPlay Backupand BitLocker Toll Tools Restore C Drive En AA SA Sharing Ce Programs Regional and Scanners and Secure and Features Language Cameras Online K VMware Welcome Windows Windows Windows Tools Center CardSpace Defender Firewall iSCSI Initiator Keyboard Mouse of m Color Management Security Center Windows Sidebar Date and Time Parental Controls Windows SideShow Search Default Fonts Game Indexing Programs Controllers Options Pen and Phone and Power Printers Input Devices Modem Options aag Speech Taskbar and Text to
10. User Recogniti Start Menu Speech Accounts ey Windows Update 3 With the Network and Sharing Center screen displayed select Manage network connections OW ss gt Control Panel Network and Sharing Center Tasks Network and Sharing Center View computers and devices Connect to network Set un a ann imn ar network A J Manage network connections TECH PC Network Diagnose anu repair This computer go Network Private network ccess Local only Connection Local Area Connection 28 Sharing and Discovery Network discovery amp On File sharing Off Public folder sharing Off Printer sharing Off no printers installed Password protected sharing On Media sharing Off Show me all the files and folders I am sharing Show me all the shared network folders on this computer NETWORK SETTINGS GINTELLINET View full map G Internet Customize View status NETWORK SOLUTIONS 4 Right click on the Local Area Connection icon to display the pop up menu then click Properties i x f x eE LEP t Control Panel Network Connections Bi Organize Views Disable this network device ba Diagnose this connection Cii Rename this connection gt gt on Name Status Device Name Connectivity Network Category Owner Type Phone or Host Addre LAN or High Speed Internet 1 A Mu Local Area Connection arii Net Hark EE Inte
11. address automatically gt Use the following DNS server addresses Advanced OK Cancel 7 When Local Area Connection Properties displays again click OK to close the screen 2 2 Confirming the Connection Once the configuration for obtaining an IP address is complete you can use the ping command to verify that the computer is able to communicate with the router Open the DOS window as detailed below and ping the IP address of the router at the DOS prompt e For Windows 98SE Me Click Start then Run enter command and click OK e For Windows 2000 XP Vista 7 Click Start then Run enter cmd and click OK If the Command window returns something similar to the lines below the connection between the router and your computer has been successfully established NETWORK SETTINGS VY INTELLINET NETWORK SOLUTIONS C Documents and Settingsladmin gt ping 192 168 2 1 Pinging 192 168 2 1 with 32 bytes of data Reply from 192 168 2 1 bytes 32 time 1ms TTL 64 Reply from 192 168 2 1 bytes 32 time 1ms TTL 64 Reply from 192 168 2 1 bytes 32 time 1ms TTL 64 Reply from 192 168 2 1 bytes 32 time 1ms TTL 64 Ping statistics for 192 168 2 1 Packets Sent 4 Received 4 Lost 0 0 loss Approximate round trip times in milli seconds Minimum 1ms Maximum 1ms Average 1ms If the computer fails to connect to the router the Command window
12. automatically When there is no access request within a set timeframe 60 3600 seconds it will disconnect e Manual On is suitable when the access method is controlled by an administrator using a password It doesn t connect to the Internet when the power is on only when you connect or disconnect manually 3 3 4 BigPond This connection option is used in conjunction with Telstra Australia s largest ISP BigPond Account Enter the user name provided by the ISP BigPond Password Enter the password provided by the ISP Please Retype Your Password For confirmation MTU The MTU Maximum Transmission Unit setting specifies the largest packet size permitted for network transmission Most DSL users should use the value 1492 You can set MTU manually and you should leave this value in the 576 to 1500 range NOTE If the wl NTELLINET ETWOR K SOLUTIONS ROUTER SETUP BigPond BigPond Account BigPond Password Please retype your password BigPond Server IF or Domain name Request IP address MTU 576 1500 Static DNS Server Primary DNS Secondary DMS optional MAT Cloning LJ Enabled MAT Address XM UMM ey o0 00 00 00 00 00 Clone MAC MTU Maximum Transmission Unit specifies the largest packet size permitted for network transmission Most DSL users should use the value 1492 You can set MTU manually but it should be left in the 576 to 1500 range NOTE If the value entered isn t in accord with the val
13. reasons it s always recommended that you change the password from the factory set default value as soon as you can NETWORK SETTINGS GINTELLINET NETWORK SOLUTIONS Enter Network Password i x i p gt This secure Web Site at 192 168 2 1 requires you to log on Please type the User Name and Password that you use for Device User Name ER v Password Save this password in your password list ones Once you ve logged in the router s user interface will display VY INTELLINET NETWORK SOLUTIONS Quick Setup Admin WAN LAN NAT Firewall Routing Qos Misc High level Status Status Log Gateway Internet IP Address 192 168 2 1 Cable DSL Disconnected Status This status page displays the router s DHCP Server Enabled Subnet Mask 0 0 0 0 current status and configuration All information is read only Subnet Mask 255 255 255 0 IP Address 0 0 0 0 MAT Enabled Gateway 0 0 0 0 Firewall Enabled DNS 0 0 0 0 Firmware Version Secondary DNS 0 0 0 0 The version number of the Firmware currently installed is displayed here i Domain Name Visit w Inkellinet network com to Information find out if there is updated firmware System Up Time 00 32 33 Connection Type Dynamic IF System Date Thu Jan 01 00 32 33 1970 Connection Time 00 00 00 Current Time The current date and time are Connected Clients 1 lelease Renew displayed Firmware version RT_EKR2 3 pli MAC Address The MAC Address of the device WAN MAC Address
14. sum Cimon EC tue wec Cito Jerr sat Comment Modify Rules Listing D z0usingimas IF Address PortType Block Time Cancel Enable Select to establish rules based on the configuration options that follow IP Address Enter the address or the range of addresses you want to control Port Type You can manually enter your preferences and click Add which will then display your new filter configuration in the Rules Listing Block Time Day Time Make selections as desired to define rules so they are applied only to specific days and or times of day Comment Enter a description to differentiate among the various client filters you configure Add Modify Click to add edit rules you ve configured ROUTER SETUP GINTELLINET ET WORK UTIONS 3 6 3 URL Filtering This screen allows you to prevent users from accessing specific Web sites using broad or narrowly defined filters Firewall Options Client Filtering URL Filtering MAC Filtering Settings URL Filter Control Deny Internet access for the Following URL addresses IP Address 192 168 2 Je Enable Modify Rules Listing Of O0fusing max URL Filter Control Select one of three options Disable URL Filter function Deny Internet Access for the following URL addresses and Allow Internet Access for the following URL addresses IP Address Enter the address or range you want to filter URL Filter String Enter a
15. unique Media Access Control MAC address assigned to it referred to as Default MAC The Clone MAC option is available for special situations for example since an ISP allows only certain MAC addresses access to the Internet selecting MAC Address and clicking Clone MAC modifies your WAN port s MAC address in order to avoid detection of the router which can lead to a service disconnect NETWORK SOLUTIONS ROUTER SETUP 3 3 3 PPPoE This connection type Point to Point Protocol over Ethernet is typically used with DSL and ADSL service PPPOE Address Mode IP Address PPPOE Account PPPOE Password Please retype your password Service Name MTU 546 1492 Maximum Idle Time 60 3600 Connection Mode Static ONS Server Primary DMS Secondary DNS MAC Cloning MAC Address 04002006 Ga a sd AA Dynamic PPPoE O Static PPPoE 1492 l 300 seconds 0 No timeout optional Enabled 00 00 00 00 00 00 Clone Mac Address Mode Select whichever service you re provided IP Address If you select Static PPPoE you must enter an IP address here PPPoE Account Enter the PPPoE username provided by your ISP PPPoE Password Enter the PPPoE password provided by your ISP Please retype your password For confirmation MTU The MTU Maximum Transmission Unit setting specifies the largest packet size permitted for network transmission Most DSL users should use the value 14
16. you to maintain the same IP address over time unlike temporary dynamic IP addresses that are assigned with each Internet connection IP Address Enter the address provided by your ISP Subnet Mask Specify a subnet mask for your WAN segment Gateway IP This is provided by your ISP MTU The MTU Maximum Transmission Unit setting specifies the largest packet size permitted for network transmission Most DSL NTELLINET ETWORK SOLUTIONS ROUTER SETUP Y l WAN Static IP Static IP Address IP Address Subnet Mask Gateway IP MTU 576 1500 Static DNS Server Primary DNS Secondary DMS Optional MAC Cloning L Enabled MAC Address XXX AX AXIAKI AS 00 00 00 00 00 00 Clone MAC More IP addresses Does ISP provide more IP addresses F users should use the value 1492 You can set MTU manually and you should leave this value in the 576 to 1500 range NOTE If the value entered isn t in accord with the value the ISP provides it can cause problems such as failure to send e mail or to browse If such a problem occurs contact your ISP for information about correcting the MTU value Primary DNS Your ISP will provide at least one Domain Name System DNS IP address DNS translates readable recognizable domain names into numerical IP addresses Enter the IP address of your DNS server here Secondary DNS Enter the IP address of a backup DNS server here MAC Address The WAN port of the router has a
17. your 4 Port Broadband Router network connections by following the steps below and referring to the Port and LED descriptions presented from left to right 1 Turn off all devices to be incorporated into the network including any PCs switches hubs the modem and the router 2 Connect the LAN or Ethernet network port of the cable DSL modem to the router s WAN port 3 Connect PCs and any switch hub used to expand the network to the router s LAN ports 4 Turn on the cable DSL modem 5 Use the included power adapter to connect the router to an AC outlet 6 Turn on the PC you ll be using to configure the router 1 1 Rear Panel Ports amp Jacks Reset PWR WAN This 10 100Mbps port connects the cable DSL modem PC1 4 These four LAN ports connect networked devices such as PCs print servers and remote hard drives If you connect a LAN port to a switch or hub check that both the device s Power LED and the router s corresponding PC LAN LED see below light to confirm the connection Reset Push this recessed button to clear all established router configuration settings and reset to the factory default settings See section 3 Restore Defaults PWR This jack is for the included external 9 V DC 500 mA power adapter HARDWARE INSTALLATION v INTELLINET TWORK SOLUTION 1 2 Front Panel LEDs O OE K EET A ESE DEES EE T ERC RE II A TRT PNE NONIE TEOR hy 4 Port Broadband Router INTELLINET WAN
18. 4 PORT BROADBAND ROUTER USER MANUAL MODEL 524957 INTELLINET W A N INTELLINET NETW OR K SOLUTIONS INT 524957 UM 1210 01 INTRODUCTION Thank you for purchasing the INTELLINET NETWORK SOLUTIONS 4 Port Broadband Router Model 524957 Combining a router firewall and four port Fast Ethernet switch this handy device lets you experience fast speeds as you surf the Web download music or photos and play online games A DHCP server that automatically assigns IP addresses to users on the LAN plus UPnP that supports gaming makes this the perfect router for the home network Keeping intruders out of your network can be a challenge but this feature rich router is designed to make that task easier It includes a true firewall that secures your network against hackers With Network Address Translation NAT to shield your networked devices from intruders plus content control using URL and MAC filtering you can rest assured that you have taken the necessary precautions to protect the data on your network The easy to follow instructions in this user manual help make setup and operation quick and simple so you ll also soon be enjoying the benefits of these additional features e Integrated 10 100 Mbps LAN switch with Auto MDI MDI X support Supports virtual server and DMZ demilitarized zone Supports DDNS dynamic DNS Supports VPN pass through PPTP L2TP QoS Quality of Service bandwidth management
19. 92 You can set MTU manually and you should leave this value in the 576 to 1500 range NOTE If the value entered isn t in accord with the value the ISP provides it can cause problems such as failure to send e mail or to browse If such ROUTER SETUP NETWORK SOLUTIONS a problem occurs contact your ISP for information about correcting the MTU value Primary DNS Your ISP will provide at least one Domain Name System DNS IP address DNS translates readable recognizable domain names into numerical IP addresses Enter the IP address of your DNS server here Secondary DNS Enter the IP address of a backup DNS server here MAC Address The WAN port of the router has a unique Media Access Control MAC address assigned to it referred to as Default MAC The Clone MAC option is available for special situations for example since an ISP allows only certain MAC addresses access to the Internet selecting MAC Address and clicking Clone MAC modifies your WAN port s MAC address in order to avoid detection of the router which can lead to a service disconnect Connection Mode There are three options in the drop down menu e Keep Alive keeps you connected to the Internet indefinitely even when your connection sits idle e Auto Connect is suitable for Internet connections that need to record the online time It doesn t connect to the Internet when the power is on only when an access request is made it will connect
20. AN MAT Firewall Routing Qos Misc High level Status Status Log System Log Last Page Thu Jan 01 00 00 00 1970 Thu Jan 01 00 00 00 1970 Thu Jan 01 OG 00 05 1970 Thu Jan 01 00 00 06 1970 Thu Jan 01 00 14 07 1970 Thu Jan 01 00 14 08 1970 Thu Jan 01 00 14 08 1970 Thu Jan 01 00 14 08 1970 Svstem System start Svstem Ver RT ER2 5 pli 17 Wed Nov 10 14 43 57 2010 DHOPSJRX REQUEST by 00 14 46 69 05 49 DHOPSJTX ACK to 192 168 7 100 DHOPSJRX DISCOVER by 00 14 46 69 D5 A9 DHOPSJTX OFFER of 192 168 2 100 DHOPSJRX REQUEST by 00 14 46 69 D5 49 DHOPSJTA ACK to 192 168 2 100 Download Settings Refresh ROUTER SETUP VY INTELLINET NETWORK SOLUTIONS 4 TROUBLESHOOTING If you forget your password Press the Reset button for 5 seconds or more with the router on to restore factory settings The default username is admin and the password Is 1234 If problems arise with the cable modem connection Confirm that the cable modem is working properly and the signal is Stable Normally there will be LEDs on the modem that indicate its operational status If any LED indicates improper operation contact your ISP Check the LEDs on the front panel of the router When the cable connections are good the PWR LED should be on and the WAN LED should be blinking If you use your computer the corresponding LAN port LED should also be blinking If not confirm that the cables are good If they check o
21. Control Panel File Edit View Favorites Tools Help O Back APG G Search i5 Folders Address vg Control Panel P i C k a catego ry g Switch to Classic view ta Appearance and 1 Printers and F lt Themes i Other Hardware See Also Ei 3 hr Windows Update v Network and n S a Help and Support im Internet User Accounts e Connections y Date Time Add or Remove i Language and Programs Regional Options 3 Click Network Connections E Network and Internet Connections File Edit View Favorites Tools Help Q sack bi Z search rer Folders HERE Address ef Network and Internet Connections as Me My Network Places Create a connection to the network at your workplace See Also Printers and Other Hardware Bl Set up or change your home or small office ad Remote Desktop network Re Phone and Modem Options or pick a Control Panel Icon Troubleshooters i Home or Small Office Networking ER Frk Network 3 Internet Ero og Internet Option 0 Connections GINTELLINET NET O RK SOLUTIONS NETWORK SETTINGS EN 4 Right click on the Local Area Connections icon to display the pop up menu then click Properties Network Connections E BIK File Edit View Favorites Tools Advanced Help ae sack 7 te 3 pp Search frr Folders Fee Address Ls Network Connections Al LAN or High Speed Internet Network Tasks ocal Area Connec
22. DNS server here 4 Once all the necessary or preferred settings have been established click Finish to exit the Quick Setup wizard At this point your router is operational To take advantage of the numerous added features continue through the following sections of the manual ROUTER SETUP VY INTELLINET NETWORK SOLUTIONS 3 2 Admin This submenu presents numerous basic yet popular configuration options and features including modifying your network password NOTE As you finish making changes to the settings on any of the menu screens click OK to implement the changes or click Cancel to clear the fields and revert to previous selections 3 2 1 Management Quick Setup Admin WA LAN MAT Firewall Routing Gos Management System Settings Firmware Upgrade Configuration Tools Language Login Account User Name Current Password New Password Re type Password Idle Time Out 60 3600 Remote Management Enabled IP Address Cancel User Name This is the one field that cannot be altered Current New Re type Password Enter as indicated Idle Time Out Enter a figure within the range in order to cut your connection with your ISP after that period of time Remote Management Select to enable disable the function and enter the number of the port you want to manage ROUTER SETUP GINTELLINET ET WORK UTIONS 3 2 2 System Settings Quick Setup Admin WAN LAN NAT Firewall Routing Q05 M
23. ETW OR K SOLUTIONS INTELLINET NETWORK SOLUTIONS offers a complete line of active and passive networking products Ask your local computer dealer for more information or visit www intellinet network com Copyright INTELLINET NETWORK SOLUTIONS All products mentioned are trademarks or registered trademarks of their respective owners
24. NS Server Select the service you ve registered with from the drop down menu DDNS Update Interval Specify the update interval DDNS Ping Test Click to check the connectivity to the DDNS provider ROUTER SETUP VY INTELLINET NETWORK SOLUTIONS 3 10 High Level This menu offers activation of an extra security measure to protect the network Quick Setup Admin WAN LAN NAT Firewall Routing Qos Misc High level Security ARP spoofing correspondence Enabled F Refresh Cancel Enabled Select to enable disable ARP Address Resolution Protocol spoofing correspondence When enabled this function will perform IP MAC binding on the WAN side at the first ARP reply in order to prevent ARP spoofing which is a type of Ethernet attack on a network 3 11 Status This menu presents two informative submenus Status and Log 3 11 1 Status This screen displays the router s current status and configuration Quick Setup Admin WAN LAN NAT Firewall Routing Qo5 Misc High level Status Status Log Gateway Internet IP Address 197 168 2 1 Cable DSL Disconnected Subnet Mask 255 255 255 0 IF Address 0 0 0 0 DHCP Server Enabled Subnet Mask 0 0 0 0 Enabled gateway 0 0 0 0 ROUTER SETUP N E SOLUTIONS TWORK 3 11 2 Log The router keeps a running log of events and activities which are displayed on the screens accessed here NOTE When the router is rebooted the logs are automatically cleared Quick Setup Admin VAN L
25. VPN Pass Through PPTP IPSec L2TP DHCP server supports static lease management Supports remote management Supports static routing Firmware updates via Web based user interface Three Year Warranty Package Contents e 4 Port Broadband Router e User manual on CD plus quick installation guide e RJ45 Ethernet cable 1 0 m 3 ft e Power adapter NTELLINET ETWORK SOLUTIONS INTRODUCTION GI TABLE OF CONTENTS 1 Hardware Installation c cccccceeseesecseeeeteeeeeeeeeeeeteeseeeeeeeeneeeess 4 1 1 Rear Panel Ports amp JackS rrrrnarnnrnnnrnarnnnrnarnnnnnernnennneneennnn 4 12 FOR Panel LEDS ccacrectcsecanissenssweneseesauereiacedennestiecpenaceninenstyens 5 2 Network Mer 5 2 1 IP Address Setup rrarenrnnrrnrnnrrnnrnnnnerrernennnrnnennennenunnnnnnennsenere 5 2 2 Confirming the Connection rrnrrnannnannnnrnannnannnnrrnnnnnnnnnre 14 2 3 Logging In to the Web Browser cccccsecseeceeeeeeeeeeeeeaes 16 3 Router Setup Lan 18 S AUCK CUD ee EEE E E E EEN 18 PN 23 NAN enn 27 TEN e EE E E 39 DNT 39 3 6 F L re 40 DJ ROUNO eee eee eer enn ae ene eee eee 43 Or OS ee epa eye E E S Ei 45 3 9 Miscellaneous rrrnrnarnarnurnnnnannnnnnnunnurnernnnnnnnennenernnnnennsnnee 47 240 TAG OVC EEE EE 49 GEER 49 4 TONES end 51 9 SEN 52 NTELLINET ETWORK SOLUTIONS TABLE OF CONTENTS wl 1 HARDWARE INSTALLATION Using the included RJ45 Ethernet cable and more as needed make
26. aximum Transmission Unit specifies the largest packet size permitted for network transmission Most DSL users should use the value 1492 You can set MTU manually but it should be left in the 576 to 1500 range NOTE If the value entered isn t in accord with the value the ISP provides it can cause problems such as failure to send e mail or to browse If a problem occurs contact your ISP NETWORK SOLUTIONS ng ROUTER SETUP Dynamic IP Address Request IP address MTU 76 1500 Static OWS Server Primary DNS Secondary DNS roptianal MAC Cloning Enabled MAC Address 04808 18006 18000 100 1600 00 00 00 00 00 00 Clone MAC Primary DNS Your ISP will provide at least one Domain Name System DNS IP address DNS translates readable recognizable domain names into numerical IP addresses Enter the IP address of your DNS server here Secondary DNS As an option you can enter the IP address of a backup DNS server here MAC Address The WAN port of the router has a unique Media Access Control MAC address assigned to it referred to as Default MAC The Clone MAC option is available for special situations for example since an ISP allows only certain MAC addresses access to the Internet selecting MAC Address and clicking Clone MAC modifies your WAN port s MAC address in order to avoid detection of the router which can lead to a service disconnect 3 3 2 Static IP This connection type allows
27. dify Rules Listing OtOfusing max Enabled Select to enable disable the function Comment Enter any description of the current mapping rules Server IP Enter the server IP address Mapping Ports Select either a protocol from the drop down menu and enter the mapping ports Add Modify Click to add edit rules you ve configured 3 5 4 Passthrough VPN Some applications require an application level gateway through the router You can select any of the three passthroughs here Point to Point Tunneling Protocol IPSec or Internet Protocol security which is a suite of protocols used to implement secure exchanges and Layer 2 Tunneling Protocol FTP Non Standard FTP Port If the FTP server is using a non standard FTP port number this can prevent FTP data connections NETWORK SOLUTIONS ROUTER SETUP Quick Setup Admin WAN LAN NAT Firewall Routi Virtual Server Port Triggering Port Mapping Passthraugh DMZ YPN PPTP passthrough Ipsec passthrough L2TP passthrough FTP Mon Standard FTP Port 0 655351 NetMeeting Haza Metmeeting passthrough Cancel from being established You should leave this in the 0 65535 range NetMeeting H323 Netmeeting Passthrough To accept the connection request from any outside NetMeeting client the virtual server for H323 Netmeeting Port 1720 must be enabled 3 5 5 DMZ Enabled Select to enable disable the function Public IP Address Make a selectio
28. is Management System Settings Firmware Upgrade Configuration Tools Language Time NTP Server IP or Domain name pool ntp arg Optional Time Zone GMT 05 00 Eastern Time US amp Canada v Daylight Saving Jenabled From to Name Host Mame inkelinet router Operating Mode NAPT Enabled EN NTS Server For reference Time Zone Select from the drop down menu Daylight Saving Select to enable disable then set the date range using the drop down menus Host Name For reference NAPT Select to enable disable Network Address Port Translation 3 2 3 Firmware Upgrade This important function allows you to upgrade the router s firmware To do so you need to download the firmware file to your local hard disk then enter that file name and path in the appropriate field on this screen You can also use the Browse button to find the firmware file on your PC Once you ve selected the new firmware file click OK to start the upgrade process You may need to wait a few minutes for the upgrade to complete Once the upgrade is complete you can start using the router NOTE It is always important that you take every precaution against a loss of power or network disconnect during any ROUTER SETUP VY INTELLINET NETWORK SOLUTIONS Management System Settings Firmware Upgrade Configuration Firmware Upgrade Current Firmware Yersion RT KR2 3 pli Firmware Date 17 Wed Nov 10 14 43 57 2010 Enter the path and name of
29. l R PRO1000 MT Netw ae Status Diagnose Bridge Connections Create Shortcut 5 Highlight Internet Protocol Version 4 TCP IPv4 and click Properties pt aoe nl mal gd rer Fe fe H Local rea Connection Properties ee Networking Connect using a Intel R PRO 1000 MT Network Connection This connection uses the following items he OM Client for Microsoft Networks ve al oos Packet Scheduler iv al File and Printer Sharing for Microsoft Networks wi Intemet Protocol Version 6 TCP IP v6 S Intemet Protocol Version 4 TCP AFv W 4 Link Layer Topology Discovery Mapper 1 0 Driver i Link Layer Topology Discovery Responder Install Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks GINTELLINET NETWORK SOLUTIONS NETWORK SETTINGS 6 Select both Obtain an IP address automatically and Obtain DNS server address automatically then click OK Internet Protocol Version 4 TCP IPV4 Properties FEN ae ene eo me General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically 3 Use the following IP address gr Obtain DNS server
30. n from the drop down menu Virtual Host Option Choose either DMZ or SDMZ2 e Demilitarized Zone or DMZ allows one local user to be exposed to the Internet for use of a special purpose service such as Internet gaming or videoconferencing It forwards all the ports at the same ROUTER SETUP GINTELLINET NETWORK SOLUTIONS r Settings Enabled Public IF Address 0 0 0 0 virtual Host Option IP Address of virtual DMZ Host 197 168 2 _ Get current LAN IP automatically Modify Rules Listing Of 6fusing max time to one PC The Port Forwarding feature is more secure because it only opens the ports you want to be opened while DMZ hosting opens all the ports of a computer exposing the computer so the Internet can see it e Super Demilitarized Zone or SDMZ is similar to DMZ except that the local user DMZ host uses the public IP address of your Internet service instead of a private IP address IP Address of Virtual DMZ if DMZ is selected Enter the local IP address of the client PC that you want to place in the DMZ MAC Address of Virtual SDMZ if SDMZ is selected When SDMZ is activated enter the MAC address of the local computer designated as the SDMZ host Get Current LAN IP automatically If the computer you re currently using is Supposed to be the DMZ host you can select this option and the IP address will be entered automatically Add Modify Click to add edit rules you ve configured
31. neiveorks Show icon in taskbar when connected GINTELLINET NET O RK SOLUTIONS NETWORK SETTINGS 5 Select Obtain an IP address automatically and Obtain DNS server address automatically click OK to return to the previous screen Internet Protocol TCP IP Properties ajx General Tou can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate F settings f Obtain an IP address automatically C Use the following IP address IP address Subnet mask Default gateway f Obtain ONS server address automatically Use the following DNS server addresses Pretered PWS server Alternate DNS server 6 When the Local Area Connection Properties screen displays again click OK HY Feskek ATL TIHA PCI Fast Ethemet Adapter Components checked are used by this commection W E Chent for Microsoft Networks w E File and Printer Sharing for Microsoft Networks Install Uninstall Properties D rcrption Transmission Contral Frotocol Intemet Protocol The delauk ac053 diverse interconnected networks Show icon in taskbar when connected EN NETWORK SETTINGS GINTELLINET NETWORK SOLUTIONS 2 1 3 Windows XP 1 On your PC s desktop click Start and go to the Control Panel 2 Select Network and Internet Connections E
32. nts default gateway IP address shown with the default value Subnet Mask Specify a subnet mask for your LAN segment DHCP Server Select to enable disable the DHCP server By enabling the router will automatically give your LAN clients an IP address IP Pool Starting Ending Address If desired define a specific range for your DHCP server to issue IP addresses to your LAN clients Lease Time From the drop down menu select the time interval after NETWORK SOLUTIONS ROUTER SETUP which the connected client computers are instructed to request a new IP address from the router DNS Proxy When activated the router acts as a DNS server in your network which means that the computer sends the DNS request to the router which in turn queries the ISP s DNS server Since the router is caching the results subsequent requests to the same domain name benefit from a performance gain NOTE These gains are negible in smaller networks so leaving this option disabled thus having the client doing the DNS look up itself is more often than not the best option 3 4 2 DHCP Client List Quick Setup Admin WAN LAN NAT Firewall Routing Qo5 LAM Settings DHCP Client List DHCP Client List Refresh Static Client Configuration Host Mame IF Address MAC Address Can A A AA AA DHCP Client List This table displays information relevant to clients connected to the router Host Name Enter the name of a static client allowed acce
33. or confirmation Service Name For reference MTU Enter a value for the largest packet size to be permitted for network transmission The default value of 1496 is recommended Maximum Idle Time Enter a figure within the range in order to cut your connection with your ISP after that period of time BigPond Select if this service Australia s largest ISP is used Click Next to advance to the next screen BigPond Account Enter the user name provided by the ISP BigPond Password Enter the password provided by the ISP Retype Password For confirmation Authentication Server This is provided by the ISP NTELLINET ETWOR K SOLUTIONS ROUTER SETUP wl Quick Setup Admin WAN LAN MAT Firewall Wizard BigPond Mode OO BigPond Account i Retype password Authentication Server IP or Domain 3 When the appropriate fields have been filled in for the selected connection type click Next to advance to the DNS Server screen Quick Setup Admin WAN LAN MAT Firewall Wizard DNS Server Static DNS Server F Enabled Primary DAS Secondary DNS oo BER i e Static DNS Server Select to enable disable the server e Primary DNS Your ISP will provide at least one Domain Name system DNS IP address DNS translates readable recognizable domain names into numerical IP addresses Enter the IP address of your DNS server here e Secondary DNS As an option you can enter the IP address of a backup
34. protocol and port The port trigger module uses a forward protocol type and port number and uses the IP address of the host that generates the trigger packet when it registers a rule Quick Setup Admin WAN LAN NAT Firewall Routing Qo5 Virtual Server Fort Triggering Pork Mapping Passthrough DMZ Settings Enabled Trigger Port Trigger Type Public Port Type Comment Rules Listing Of10fusing max Enabled Select to enable disable the function Trigger Port Enter a range of ports Trigger Type Select either TCP or UDP from the drop down menu Public Port Enter a range of ports Public Type Select either TCP or UDP from the drop down menu Comment Enter any description of the configured trigger Add Modify Click to add edit rules you ve configured 3 5 3 Port Mapping This submenu function allows you to set up public services on your ROUTER SETUP GINTELLINET NETWORK SOLUTIONS network such as Web servers FTP servers e mail servers and other specialized Internet applications for example videoconferencing or online gaming When users send this type of request to your network via the Internet the router will forward the request to the appropriate PC Quick Setup Admin WAN LAN NAT Firewall Routing Qo5 Misc Hii virtual Server Fort Triggering Fort Mapping Passthrough DMZ Settings Enabled F Server IP 192 168 2 Mapping Ports port1 port2 port3 port4 Type Mo
35. ptici honnan Poss Opie Fr Dial up Connections dd a 9 Sec Sounds ard pers ard Tasks Pein Pasamnonds NETWORK SETTINGS OINTELLINET NETWORK SOLUTIONS 3 Right click on the Local Area Connections icon to display the pop up menu then click Properties I EY Network and Dial up Connections File Edit View Favorites Tools Advanced Help da Back p t Bak E search LFolders og iS GS X search L Folders 4 ft OS x r EE Eia Address eter Network and Dial up Connections Go cel aa gE U Make New Local 4rea and Dial Up Connection Connection Connections Local 4rea ee Dj ahle Status i Create Shortcut Local Area Connection 2 Delete Type LAN Connection Rename Status Enabled Froperties Realtek RTL8159041 PCI Fast Ethernet Adapter Displays the properties of the selected connection a 4 Highlight Internet Protocol TCP P and click Properties Ling cal Area Connection 7 Properties General Sharing HY Reakek ATLE INA PCI Fast Ethernet Adapter Components checked are used by this connection W E Chent for Microsoft Networks File and Printer Sharing for Microsoft Networks Install Uninstal Properlies Dasenplion Transmiz sjon Control Froiocolntemrnet Protocol The defaut wade area network protocol that prowdes communscation acess Grease interconnected
36. roduct contact your local city office your household waste disposal service or the shop where you purchased this product In countries outside of the EU If you wish to discard this product contact your local authorities and ask for the correct manner of disposal FEDERAL COMMUNICATIONS COMMISSION REGULATORY STATEMENT FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of Federal Communications Commission FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver e Connect the equipment to an outlet on a circuit different from the receiver e Consult the dealer or an experienced radio TV technician for help CE Fe NETWORK SOLUTIONS INTELLINET N
37. sabled RIP1 RIP2 Broadcast or RIP2 Multicast aay 3 8 QoS This menu presents Quality of Service options so you can provide different priorities to different applications users or data flows or to guarantee a certain level of performance to a data flow based on your specific network needs 3 8 1 Port Based Quick Setup Admin WAN LAN NAT Firewall Routing 05 Port based DSCP Settings Enable Port rate Control wl E SOLUTIONS TWORK ROUTER SETUP Enable Port Rate Control Select to enable disable the function LAN 1 4 WAN For each network connection enter a maximum uplink downlink bandwidth 3 8 2 DSCP Port based DSCP Settings Enable DSCP High queue weight 1 15 Medium queue weight 1 15 Low queue weight 1 15 Enable Rule F DSCP value 0 63 Queye map Low Priority ww Description Modif Rules Listing Oiofusing max fps value Enable DSCP Select to enable disable the function High Medium Low Queue Weight Enter your preferred values Enable Rule Select to enable disable the function DSCP Value Enter your preferred value ROUTER SETUP GINTELLINET NETWORK SOLUTIONS Queue Map Select a priority level from the drop down menu Description Enter a description to differentiate among any number of rules that are established 3 9 Miscellaneous This menu presents a couple of popular functions that can be configured and put
38. specific Web site name or domain name or any defining keywords for example games youtube nude that could help focus the filter 3 6 4 MAC Filtering This screen allows you to allow or restrict communication between specified nodes MAC Access Control Select one of three options Disable MAC Address Control function Deny Internet Access for the following MAC addresses and Allow Internet Access for the following MAC addresses MAC Address Enter the MAC address using the format shown you ROUTER SETUP GINTELLINET NETWORK SOLUTIONS Firewall Options Client Filtering URL Filtering MAC Filtering Settings MAC Address Control Deny Internet access for the following MAC addresses MAC Address 58 8000 UGA a Comment Rules Listing OzDfusing max want to control The format is 00 00 00 00 00 00 using the characters 0 9 and a f Comment Enter a description to differentiate among the various filters you configure 3 7 Routing This menu presents options for optimizing pathways for information packets thus maximizing the efficiency and speed of the router 3 1 Routing Table Routing Routing Table Static Routing Dynamic Routing Routing Table List Destination Network IF Subnet Mask Gateway IP Refresh The Routing Table List displays the current routing information as it pertains to the network Click Refresh to update GINTELLINET TWOR K UTIONS ROUTER SETUP
39. ss to the router IP Address Enter the IP address of a static client allowed access to the router MAC Address Enter the MAC address of a static client allowed access to the router ROUTER SETUP VY INTELLINET NETWORK SOLUTIONS 3 5 NAT The network address translation NAT menu presents options that make it possible to open ports create a DMZ and perform other functions 3 5 1 Virtual Server Some games servers and applications don t work in conjunction with NAT unless a virtual server is established to provide WAN to LAN port mapping Quick Setup Admin VAN LAN NAT Firewall Routing Q05 Misc Hic virtual Server Port Triggering Port Mapping Passthrough DMZ Settings Enabled F Private IF 192 168 2 Private Port Hais Payt Type Comment Mo dif Rules Listing Of2O0fusing max Enabled Select to enable disable the function Private IP This is the address of the internal host for which you want to open a port Private Port Enter an internal port number Public Port Enter an external port number Type Select the protocol that s required for the service you re setting up TCP or UDP Comment Enter any description of the current virtual server item Add Modify Click to add edit rules you ve configured NETWORK SOLUTIONS ROUTER SETUP 3 9 2 Port Triggering The port trigger module dynamically registers virtual server rules when any IP host generates the packet from the specified trigger
40. stalled on your computer Do not choose the TCP IP listing that has the words Dial Up Adapter beside it Click Properties to display the TCP IP Properties dialog box Ensure Obtain IP Address Automatically is selected checked In the WINS Configuration dialog box ensure that Disable WINS Resolution is checked In the Gateway dialog box remove all entries from the Installed gateways section by selecting them and clicking Remove In the DNS Configuration dialog box remove all entries from the DNS Server Search Order box by selecting them and clicking Remove Remove all entries from the Domain Suffix Search Order box by selecting them and clicking Remove Click Disable DNS 10 Click OK to return to the Network Configuration dialog box 11 Click OK If prompted to restart click Yes 2 1 2 Windows 2000 1 On your PC s desktop click Start and Settings then go to the Control Panel 2 Double click the Network and Dial up Connections icon J Control Panel Fle Edt Yew Favorter Took Hep ies gt GI seen Greens AG Xn ER Address Control Panel Accept Aee Addiitemere Admietratse Aud Control Panel Options H r denir Pr og str Taak Lie Melwork ard bal ugp Connectors ar a PA Cornadts bo other oompuker i Fired Fast Folder Orten Forts aie l h ivaka ved be iT Carkrelers O Network and
41. the upgrade File then click the OK button below ae firmware upload procedure as such an occurence can cause damage both to the file and the router itself 3 2 4 Configuration Management System Settings Firmware Upgrade Configuration Tools Settings Restore Factory Default Backup Settings Restore Settings Cancel Restore Factory Default Select to put everything into factory configuration Make sure you have made a copy of what you ve configured The default settings are admin for Username 1234 for Password 192 168 2 1 for IP Address and 255 255 255 0 for Subnet Mask Backup Settings Select to back up the current settings in your computer Restore Settings Select to restore the settings that are stored in your computer Click Browse to select the proper files then click OK wl NTELLINET ETW OR K UTIONS ROUTER SETUP 3 2 5 Tools Management System Settings Firmware Upgrade Configuration Tools Restart Device Reboot Immediately Reboot Reboot Click to restart the router 3 2 6 Language Management System Settings Firmware Upgrade Configuration Tools Language Settings Language Language Make a selection from the drop down menu 3 2 7 Log Settings Settings Remote Log Log Server Email Log Send Email Sender Email Address Receiver Email Address SMTP Server Enable 4uthentication Account Name Password Re type Password
42. tion fs Create a new connection add Disable pet Set up home or small Status office network et Disable this network device DN Repair this connection APERA Bridge Connections mij Rename this connection RR Shortcut View status of this ete connection Rename 2 B Change settings of this Properties connection i 5 On the subsequent Local Area Connection Properties screen select Internet Protocol TCP IP and click Properties Local Area Connection Properties Desenphion Transmssion Control Protecolintemet Protocol The default wide area netvork potona that prowdes communrscalion actor dee meconnected nebvorks C Show icon in notification area when connected NETWORK SETTINGS GINTELLINET O RK SOLUTIO 6 Select both Obtain an IP address automatically and Obtain DNS server address automatically then click OK Internet Protocol TCP IP Properties 7 E General Altemate Configuration Tou can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically O Use the following IP address Obtain DNS server address automatically O Use the following
43. to use Universal Plug and Play UPnP and Dynamic Domain Name Service DDNS 3 9 1 UPnP UPnP Universal Plug and Play allows the automatic discovery and configuration of equipment attached to your LAN providing compatibility with networking equipment software and peripherals of the 400 plus vendors that participate in the Universal Plug and Play forum UPnP CENS Settings Enable UPnP Enabled Advertise Tine 60 1600 1500 Refresh Port Mapping Refresh External Internal Remote Host Port Internal Client Port Protocol Description Enable UPnP Select to enable disable the function Advertise Time Enter the preferred value Refresh Port Mapping Click to update the list NETWORK SOLUTIONS ROUTER SETUP 3 9 2 DDNS The DDNS Dynamic Domain Name Service feature allows you to use a domain name instead of an IP address to access Internet sites Before you can use this feature however you need to register an account for DDNS service at a DDNS service provider such as DynDNS Quick Setup Admin WAN LAN NAT Firewall Routing Qos Misc pie DUNS Settings Enable DDNS Enabled Host Mame DONS Server dyndns org sv User Name Password DONS Update Interval D 864001Minutes DONS Ping Test Enable DDNS Select to enable disable the DDNS server Host Name User Name Password After you register a DDNS account with a DDNS service you ll receive the information to enter in each of these fields DD
44. ue the ISP provides it can cause problems such as failure to send e mail or to browse If a problem occurs contact your ISP Primary DNS Your ISP will provide at least one Domain Name System DNS IP address DNS translates readable recognizable domain names into numerical IP addresses Enter the IP address of your DNS server here Secondary DNS Enter the IP address of a backup DNS server here MAC Address The WAN port of the router has a unique Media Access Control MAC address assigned to it referred to as Default MAC The Clone MAC option is available for special situations for example since an ISP allows only certain MAC addresses access to the Internet selecting MAC Address and clicking Clone MAC modifies your WAN port s MAC address in order to avoid detection of the router which can lead to a service disconnect ROUTER SETUP VY INTELLINET NETWORK SOLUTIONS 3 4 LAN This menu with its two submenu screens LAN Settings and DHCP Client List presents options for configuring your local area network 3 4 1 LAN Settings Quick Setup Admin WAN LAN NAT Firewall LAN Settings DHCP Client List Settings IP Address 197 166 2 1 Subnet Mask 99 05 205 0 The Gateway acts as DHCP Server Enabled IF Pool Starting Address 197 165 2 IF Pool Ending Address 197 166 2 Lease Time Eight hours DNS Proxy Enabled IP Address This is the router s LAN port IP address your LAN clie
45. ut okay re visit Section 3 2 4 Configuration to make sure your configuration is correct If you can t access the Internet go to the next step Open Internet Explorer or another Web browser and enter 192 168 2 1 in the address bar then press lt Enter gt Enter admin in the User Name field and 1234 in the Password field then click OK Click LAN in the top menu select DHCP Server then click OK and close the browser window NTELLINET ETW OR K SOLUTIONS TROUBLESHOOTING wl 5 SPECIFICATIONS Standards e IEEE 802 3 10Base T Ethernet e IEEE 802 3u 100Base TX Fast Ethernet General e LAN ports 4 RJ45 10 100 Mbps data ports e LAN ports with Auto MDI MDI X e WAN port 10 100 Mbps RJ45 connector e Certifications FCC Class B CE Router e Supported WAN connection types Dynamic IP DHCP for cable service or DSL Static IP PPPoE PPTP for DSL e Protocols CSMA CD TCP IP UDP ICMP Virtual server Special applications port trigger DMZ demilitarized zone e Firewall URL filter MAC address filter Connection Filtering Limit access to the Internet to PCs in the LAN based on a time schedule NTELLINET ETWORK SOLUTIONS SPECIFICATIONS GI Supports UPnP Universal Plug and Play Supports DHCP client server Supports PPPoE DSL DHCP cable DSL and static IP Supports VPN PPTP L2TP pass through LEDs e Power e WAN Link Act
46. will return the following which indicates that the computer network settings and cable connections between the router and the computer should be checked C Documents and Settingsladmin gt ping 192 168 2 1 Pinging 192 168 2 1 with 32 bytes of data Request timed out Request timed out Request timed out Request timed out Ping statistics for 192 168 2 1 Packets Sent 4 Received 0 Lost 4 100 loss Remember in order for your network to operate properly the router needs to be configured through your Web browser as explained in the folowing section NTELLINET ETW OR K SOLUTIONS NETWORK SETTINGS wl 2 3 Logging In to the Web Browser 1 Open a Web browser Microsoft Internet Explorer Firefox Safari etc on the computer you ve just connected to the router and enter the IP address 192 168 2 1 in the address bar about blank Microsoft Internet Explorer File Edit View Favorites Tools Help gt x 2 A p Search Se Favorites 4 gt r or d Agdres 43 http 192 163 2 1 Press lt Enter gt on your keyboard to display a login window below 2 With the Enter Network Password screen displayed fill in the User Name and the Password fields using the default values admin for the username 1234 for the password if this is the first time you re logging in and you haven t changed your security settings yet see Section 3 2 1 Management NOTE For security
Download Pdf Manuals
Related Search