Metra 99-7860 mounting kit
Contents
1. White Left Front 00 White Black Right Rear Violet Right Rear J Violet Black Left Rear Green Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications A 1 800 221 0932 m www metraonline com REV 07 22 09 COPYRIGHT 2009 METRA ELECTRONICS CORPORATION INST99 78602. INSTALLATION INSTRUCTIONS FOR PART 99 7860 APPLICATIONS Honda Civic SI 2002 2005 US Models Only 99 7860 KIT FEATURES e DIN Head Unit Provision With Pocket e ISO DIN Head Unit Provision With Pocket e Stacked ISO Head Unit Provision e Double DIN Head Unit Provision KIT COMPONENTS e A Single DIN Radio Housing e B ISO Brackets e C ISO Trim Plate e D Double DIN Trim Plate WIRING AND ANTENNA CONNECTIONS Sold Separatel Harness e 70 1721 Honda Acura harness 1998 up Antenna Adapter e Not Required TOOLS REQUIRED Phillips Screwdriver e Offset Tool Not Pictured SS rey 1 800 221 0932 www metraonline com COPYRIGHT 2002 2009 METRA ELECTRONICS CORPORATION mi JM TABLE OF CONTENTS Dash Disassembly Honda Civic SI 2002 2005 ssssssunnunnunnan nrrrr1l Kit Assembly DIN Head Unit Provision With Pocket ss sasana nnnnnnnn 0 SO Din Head Unit Provision With Pockel ss sr rrrrrnn arad Double Din Head Unit Provision ssssssrr ranah Stacked ISO Head Unit Provision sccccccccccunccucneseneesannsd Fillal ASSCMNDN arsaa anaa senses E BEN aaa aaa Note Refer also to the instructions included with the aftermarket radio KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry Log onto www installerinstitute com or call 800 354 6782 for more
3. after market ISO head units and mount with the screws supplied with the unit Figure A 2 Snap the Double DIN Trimplate over the head unit Figure B Continue to final assembly Assembled kit rE a QG 99 7860 FINAL ASSEMBLY FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radio and dash assemblies in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Acc Red 12V Batt Memory Yellow COUN anana ewan aa Black Power Antenna Blue Amp Turn On Blue White Amp Ground Black White Illumination Orange DIMME s cecraciensts be curs Orange White Right Front Gray Right Front 5 Gray Black Left Front
4. ded with the aftermarket radio Align the holes in the ISO Snap in Backets with the holes in the head unit and mount the brackets to the head unit with the screws supplied with the unit Figure A 2 Slide the head unit bracket assembly into the radio opening until the side clips engage Figure B 3 Snap the ISO trimplate over the head unit Figure C 4 Snap the housing assembly into the dash trim bezel Figure C NOTE To remove the mounted head unit unclip and remove the ISO Trimplate Using a small flat blade screwdriver disengage the side clips securing the ISO Snap In Brackets to the housing pocket assembly Continue to final assembly Assembled kit zz Mens 99 7860 KIT ASSEMBLY DOUBLE DIN HEAD UNIT PROVISION Note Refer also to the instructions included with the aftermarket radio 1 Align the holes on the factory backet assembly with the holes on the after market Double DIN head unit and mount with the screws supplied with the unit Figure A 2 Cut and remove the center rib shad ed from the Double DIN Trimplate Figure B 3 Snap the Double DIN Trimplate over the head unit Figure C Continue to final assembly Assembled kit zee Mel s 99 7860 KIT ASSEMBLY STACKED ISO HEAD UNIT PROVISION Note Refer also to the instructions included with the aftermarket radio 1 Align the holes on the factory backet assembly with the holes on the
5. information and take steps toward a better tomorrow Na kN Mens 99 7860 DASH DISASSEMBLY Honda Civic SI 2002 2005 Disconnect the negative battery terminal to prevent an accidental short circuit Remove the shift knob and unsnap the shifter lever trim panel 3 Using the offset tool remove 2 lower bolts securing the center panel 4 Unsnap and remove the dash trim bezel and disconnect the wiring 9 Remove 3 Philips screws securing the climate control pod to the back of the dash trim bezel and remove the pod 6 Remove 4 Phillips screws from each side securing the factory head unit and pocket to the bracket assembly and remove NOTE Removing the glove box and the drivers side lower trim panel may be necessary when removing the Shifter level trim panel when not using an offset tool Continue to kit assembly Mel 99 7860 KIT ASSEMBLY DIN HEAD UNIT PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio 1 Slide the DIN cage into the radio opening of the Housing and secure by bending the metal locking tabs down Figure A 2 Slide the DIN unit into the cage until it is secure Figure B 3 Snap the housing assembley into the dash trim bezel Figure C Continue to final assembly Assembled kit zee Mel s 99 7860 KIT ASSEMBLY ISO DIN HEAD UNIT PROVISION WITH POCKET Note Refer also to the instructions inclu
Download Pdf Manuals
Related Search