Metra 99-2007 mounting kit
Contents
1. supplied with the radio Figure C Snap the radio housing trim plate onto the front of the radio housing Figure D Continue to final assembly DOUBLE DIN RADIO PROVISION Note Refer also to the instructions included with the aftermarket radio 99 2007 KIT ASSEMBLY 1 Attach the radio housing brackets to the inside edge of the radio housing Figure A 2 Slide the Double DIN radio into the radio housing bracket assembly and secure the unit using the screws sup plied with the radio Figure B 3 Snap the radio housing trim plate onto the front of the radio housing Figure C Continue to final assembly f mens 99 2007 KIT ASSEMBLY STACKED ISO UNITS PROVISION Note Refer also to the instructions included with the aftermarket radio 1 Attach the radio housing brackets to the inside edge of the radio housing Figure A 2 Slide the stacked ISO units into the radio housing bracket assembly and secure the unit using the screws sup plied with the units Figure B 3 Snap the radio housing trim plate onto the front of the radio housing Figure C Continue to final assembly ZZ ES NT FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any unused2. wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radio and dash assemblies in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Acc Red 12V Batt Memory Yellow GPOUNd 0 cee ee aes Black Power Antenna Blue Amp Turn On Blue White Amp Ground Black White llumination Orange Dimmer 0 eee aes Orange White Right Front Gray Right Front c Gray Black Left Front 00 White Left Front White Black Right Rear 08 Violet Right Rear Violet Black Left Rear ee Green Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications A 1 800 221 0932 m www metraonline com REV 04 21 10 COPYRIGHT 2004 2010 METRA ELECTRONICS CORPORATION INST99 2007
3. INSTALLATION INSTRUCTIONS FOR PART 99 2007 APPLICATIONS Cadillac Escalade 2007 2010 99 2007 KIT FEATURES e ISO Mount Radio Provision With Pocket e Double DIN Radio Provision e Stacked ISO Units Provision KIT COMPONENTS A Radio Housing e B Radio Housing Trim Plate e C Radio Housing Brackets D Pocket e E 4 8 3 8 Screws WIRING AND ANTENNA CONNECTIONS Sold Separately e 40 CR10 2002 up Chrysler GM Antenna Adapter e GMOS LAN 05 2007 up GM LAN Digital Amp Interface TOOLS REQUIRED Small Flat Blade Screwdriver Panel Removal Tool e Phillips Screwdriver Socket Set A 1 800 221 0932 m www metraonline com COPYRIGHT 2004 2010 METRA ELECTRONICS CORPORATION oo 992007 TABLE OF CONTENTS Dash Disassembly Cadillac Escalade 2007 2010 id EC ee RAF FN RAS AYN A E N 4 Kit Assembly ISO Mount Radio Provision with Pocket 1 J Double DIN Radio Provision SEDD DRUD Da Stacked ISO Units Provision YF RR E Final Assembly ri iA RY YY YY WAEDU Y RAA ne nese Note Refer also to the instructions included with the aftermarket radio KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry Log onto www installerinstitute com or call 800 354 6782 for more information and take steps toward a better tomorrow E
4. Zzc 99 2007 DASH DISASSEMBLY CADILLAC ESCALADE 2007 2010 A 1 Disconnect the negative battery ter minal to prevent an accidental short circuit 2 Unclip and remove cup holder and ashtray assembly Figure A 3 Unclip and remove the trim panel above the glove box including the a c vent Figure B 4 Unclip and remove the entire panel surrounding the radio including the a c vents Figure C 5 Remove 6 9 32 screws to extract radio from dash Figure D Continue to kit assembly _ Oar O9 POO7 KIT PREPARATION CADILLAC ESCALADE 2007 2010 1 Cut and remove the shaded areas marked with an S only from the radio housing Figure A Right side and top of Radio housing Figure B Left side and top of Radio housing NOTE Do NOT remove the tab marked with both S and E Continue to kit assembly y Mel 99 2007 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio mc Flip the radio housing brackets upside down then snap them to the inside edge of the radio housing Figure A NO Slide the pocket into the top of the opening aligning the holes in the radio housing brackets with the bosses on the pocket and secure using the provided 4 8 3 8 screws Figure B Gad Slide the ISO radio into the opening below the pocket and secure the unit to the kit using the screws
Download Pdf Manuals
Related Search