Metra 95-7605 mounting kit
Contents
1. INSTALLATION INSTRUCTIONS FOR PART 95 7605 APPLICATIONS INFINITI G35 Coupe 2005 07 INFINITI G35 Sedan 2005 06 Painted And Finished To Match Factory Dash KIT FEATURES e ISO Double DIN Radio Provision e Stacked ISO Mount Units Provision KIT COMPONENTS A Radio Housing e B Climate Control Cable f IA TOOLS REQUIRED Small Flat Blade Screwdriver Panel Removal Tool e Phillips Screwdriver e Hook Tool A 1 800 221 0932 www metraonline com COPYRIGHT 2008 METRA ELECTRONICS CORPORATION m7 95 7605 TABLE OF CONTENTS Dash Disassembly Infiniti G35 Coupe 2005 2007 G35 Sedan 2005 06 1 2 Kit Assembly Double DIN Stacked ISO Mount Units Provision 3 Final ASSCHUNY sora 4 Note Refer also to the instructions included with the aftermarket radio zh i I Ae A 95 7605 DASH DISASSEMBLY INFINITI G35 Coupe 2005 07 INFINITI G35 Sedan 2005 06 1 Disconnect the negative battery ter minal to prevent an accidental short circuit 2 Push down on the collar below the shift knob to unclip Using a small screwdriver or hook tool remove the spring clip to release and remove the shift knob Figure A Unclip and remove the shifter trim panel including the ashtray cigarette lighter Figure B en a Remove 2 Phillips screws exposed under the trim panel removed in step 3 from the panels on the left and right2. ray 12V Batt Memory Yellow Right Front Gray Black GOWN eege Black Left Front White Power Antenna Blue Left Front White Black Amp Turn On Blue White Right Rear Violet Amp Ground Black White Right Rear Violet Black IIlumination Orange Left Rear Green Dimmer Orange White Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications 4 nn E ZZ 95 7605 NOTES 95 7605 INSTRUCTIONS A 1 800 221 0932 www metraonline com REV 05 30 08 COPYRIGHT 2008 METRA ELECTRONICS CORPORATION INST95 7605
3. side of the radio climate control panel assembly Figure C Sl Unclip and remove the trim panels on the left and right side of the radio cli mate control panel assembly Figure D Unclip and remove the thin plastic trim piece at top edge of dash Figure E Unclip and remove the hood panel above the clock on the top of the dash Figure F Continued on page 2 zz LES A 95 7605 DASH DISASSEMBLY INFINITI G35 Coupe 2005 07 INFINITI G35 Sedan 2005 06 8 Unclip and remove the trim panel at the bottom of the clock panel then remove the 1 Phillips screw exposed below it Figure G 9 Remove 2 Phillips screws below the radio climate control panel and 2 Phillips screws at the top of the radio climate control panel assembly between the a c vents Figure H 10 Unclip the radio climate control panel factory bracket Unplug and remove the assembly Figure H 11 Unclip the ribbon cable joining the radio climate control panel to the radio chassis Figure I 12 Remove 8 Phillips screws securing the radio chassis and 6 Phillips screws securing the radio climate control panel to the factory bracket assembly Save screws and bracket for re use during kit assembly Continue to kit assembly LES 95 7605 KIT ASSEMBLY DOUBLE DIN ISO STACK MOUNT UNITS PROVISION Note Refer also to the instructions included with the aftermarket radio Posi
4. tion the aftermarket double DIN or stacked ISO mount unit s into the factory bracket assembly and secure using the screws supplied with the aftermarket unit s Figure A ms gt Attach the radio housing to the factory bracket assembly using the factory hard ware Figure B 3 Connect the black end of the climate control cable to the climate controls in the radio housing and connect the other end of the cable to the factory climate control harness during final assembly Continue to final assembly zh MESA 235 7605 FINAL ASSEMBLY FINAL ASSEMBLY A Strip wire ends hack 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radio and dash assemblies in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Acc Red Right Front G
Download Pdf Manuals
Related Search