Zebra LS7808
Contents
1. Symbol LS7808 Horizontal Slot Scanner Quick Reference Guide 2 Symbol LS7808 Horizontal Slot Scanner 2007 2010 MOTOROLA INC All rights reserved Motorola reserves the right to make changes to any product to improve reliability function or design Motorola does not assume any product liability arising out of or in connection with the application or use of any product circuit or application described herein No license is granted either expressly or by implication estoppel or otherwise under any patent right or patent covering or relating to any combination system apparatus machine material method or process in which Motorola products might be used An implied license exists only for equipment circuits and subsystems contained in Motorola products MOTOROLA the Stylized M Logo and Symbol and the Symbol logo are registered trademarks of Motorola Inc Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged Motorola Inc One Motorola Plaza Holtsville N Y 11742 1300 http www motorola com enterprisemobility Warranty For the complete Motorola hardware product warranty statement go to http www motorola com enterprisemobility warranty Quick Reference Guide 3 Introduction This guide is designed to assist during routine LS7808 operation Detailed information about unpacking installation performance sp2. The host has disabled scanning or overridden parameter settings Scanner is not programmed for the correct host type Bar code is decoded but not transmitted to the host 11 Possible Solutions Ensure the host has power and is on If the scanner uses a separate power supply ensure it s connected to a working AC outlet Power up sequence is incorrect Refer to the LS7808 Product Reference Guide for more information Check for loose cable connections Ensure scanner is programmed to read the bar code type you are scanning Try scanning other bar codes of the same bar code type Move the bar code closer to the scanner See the technical person in charge of scanning Scan the appropriate host type bar code 12 Symbol LS7808 Horizontal Slot Scanner Problem Possible Causes Possible Solutions Scanned data is Scanner is not Ensure proper host is incorrectly displayed programmed to work selected on the host with the host Check For RS 232 ensure the scanner host type scanner s communication parameters or editing parameters match the host s options settings For keyboard wedge ensure scanner is programmed with the correct country code and that the CAPS LOCK key is off Ensure editing options e g UPCE to UPCA Conversion are properly programmed Although the green The scanner has gone Move a bar coded item over and red LEDs are on into the low power the acti
3. Installation Guide for mounting installation instructions 4 Symbol LS7808 Horizontal Slot Scanner Operating the Scanner Parts LED Indicator Connector Cover Connector Ports behind Connector Cover Power The LS7808 does not have an on off switch It is ready to scan when connected to a power supply Indicator Lights The scanner employs an LED with a combination of red and green lights to indicate operation and decode status See LED Definitions on page 10 for the different light combinations and their meanings If the scanner is not operating normally contact the technical person in charge of scanning or call Motorola Enterprise Mobility Support see details on the back cover Quick Reference Guide 5 Sleep Mode The scanner automatically enters Sleep mode when it has been inactive for a specified length of time The scanner has two levels of sleep laser and motor In laser sleep mode after ten seconds of inactivity the laser pulses at a 50 rate and then drops to 3 after a specified time In motor sleep mode the scanner is programmed to turn off the motor and the laser To wake the scanner from sleep mode present a bar code at the scanner window Beeper Volume The scanner emits a short beep when it successfully reads a bar code The volume of the beep is changed electronically by a command sent by the host or by scanning one of the beeper volume bar codes in the LS7808 Product Reference Guide See Be
4. direction of the scan arrow or place the item in front of the scanner Scanner Window 4 Upon successful decode the scanner beeps and the green LED flashes momentarily 8 Symbol LS7808 Horizontal Slot Scanner Active Scan Area The active scan area in front of the scanner window is optimized to scan items as they move in the direction of the scan arrow The dotted areas below represent the active scan area Cc Scanner Window Beeper Definitions The scanner communicates with the user by emitting different beeper sequences and patterns See the Beeper Indications table below for beeper sequences that occur during both normal scanning and while programming the scanner Beeper Sequence Indication Standard Use 3 high beeps Power up High beep A bar code symbol was decoded if decode beeper is enabled 4 long low beeps A transmission error was detected in a scanned symbol The data is ignored This occurs if the scanner is not properly configured Check option setting 5 low beeps Conversion or format error High high high low RS 232 receive error on RS 232 host or RS 232 auxiliary beeps port Quick Reference Guide 9 Beeper Sequence Indication Code 39 Buffering High low beep New Code 39 data was entered into the buffer 3 long high beeps Code 39 buffer is full Low high low beeps The Code 39 buffer was erased or there was an attempt to clear or transmit an empty buffer Low high b
5. e part number STIxx xxxx is used the scanner autocoders the type of host so there is no need to scan host type selection bar codes If a USB interface is used the scanner autocoders the USB and defaults to the HID keyboard interface See page 27 to select the IBM Hand Held host type Refer to the LS7808 Product Reference Guide p n 72 69531 XX for additional USB host types If a Keyboard Wedge RS 232 Wand Emulation or IBM 46XX host is used select that host type from the programming bar codes that follow If Keyboard Wedge is selected also select a country keyboard type from the following pages Keyboard Wedge Host Type IBM PC AT amp IBM PC Compatibles Quick Reference Guide 15 Keyboard Wedge Host Type continued J NOTE When scanning the desired bar code cover other bar code on page IBM PS 2 Model 30 IBM AT NOTEBOOK 16 Symbol LS7808 Horizontal Slot Scanner Keyboard Wedge Host Type continued J NOTE When scanning the desired bar code cover other bar code on page NCR7 7052 Country Keyboard Types Country Codes Country keyboard options apply to the Keyboard Wedge interface only North American Quick Reference Guide 17 Country Keyboard Types continued J NOTE When scanning the desired bar code cover other bar code on page French French Canadian Win95 98 18 Symbol LS7808 Horizontal Slot Scanner Country Keyboard Types continued J NOTE When scanning the desired bar code cover
6. motorola com recycling weee Magyar Az EU ban v s rl knak Minden t nkrement term ket a Motorola v llalathoz kell eljuttatni jrahasznos t s c lj b l A term k visszajuttat s nak m dj val kapcsolatos tudnival k rt l togasson el a http www motorola com recycling weee weboldalra Malti G al klijenti fl UE il prodotti kollha li jkunu waslu fl a ar tal ajja ta l u u tag hom iridu ji u rritornati g and Motorola g ar ri ikla G al aktar tag rif dwar kif g andek tirritorna l prodott jekk jog bok zur http www motorola com recycling weee Nederlands Voor klanten in de EU alle producten dienen aan het einde van hun levensduur naar Motorola te worden teruggezonden voor recycling Raadpleeg http www motorola com recycling weee voor meer informatie over het terugzenden van producten Quick Reference Guide 35 Polski Klienci z obszaru Unii Europejskiej Produkty wycofane z eksploatacji naleg y zwr ci do firmy Motorola w celu ich utylizacji Informacje na temat zwrotu produkt w znajduj si na stronie internetowej http www motorola com recycling weee Portugu s Para clientes da UE todos os produtos no fim de vida devem ser devolvidos Motorola para reciclagem Para obter informa es sobre como devolver o produto visite http www motorola com recycling weee Rom nesc Pentru clientii din UE Toate produsele la sfarsitul duratei lor de functionare trebuie returnate la Motorola pentru
7. EWING OF T rrr CAUTION CLASS 2 LASER LIGHT WHEN OPEN DO NOT STARE INTO THE BEAM VORSICHT LASERLICHT KLASSE 2 WENNABDECKUNG GE FFNET NICHT IN DEN STRAHL BLICKEN ATTENTION LUMIERE LASER DE CLASS 2 NE PAS _ REGARDER DANS LE FAISCEAU mbol LS7808 Horizontal Slot Scanner Laser Labels In accordance with IEC60825 1 and EN60825 the following information is provided to the user C ENGLISH CLASS 1 CLASS 1 LASER PRODUCT CLASS 2 LASER LIGHT DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT DANISH DANSK KLASSE 1 KLASSE 1 LASERPRODUKT KLASSE 2 LASERLYF KLASSE 2 LASERPRODUKT DUTCH NEDERLANDS KLASSE 1 KLASSE 1 LASERPRODUKT KLASSE 2 LASERLICHT NIET IN STRAAL STAREN LASERPRODUKT KLASSE 2 LASERPRODUKT FINNISH SUOMI LUOKKA 1 LUOKKA 1 LASERTUOTE LUOKKA 2 LASERVALO ALA TUIJOTA SADETTA LUOKKA 2 LASERTUOTE FRENCH FRANCAIS CLASSE 1 PRODUIT LASER DE CLASSE 1 CLASSE 2 LUMIERE LASER NE PAS REGARDER LE RAYON FIXEMENT PRODUIT LASER DE CLASSE 2 GERMAN DEUTCH KLASSE 1 LASERPRODUKT DER KLASSE 1 KLASSE 2 LASERSTRAHLEN NICHT DIREKT IN DEN LASERSTRAHL SCHAUEN LASERPRODUKT DER KLASSE 2 JAPANESE A 8 QSAl JIRI LEE D522 LH HR ER L ALT lt TEL 9522 LE CHINESE fai AH x 1 X 1 Botham 2 E EMER 2 MEE m Power Supply REA 1 NN II AN 17 RDI NN 2 nn DVN WN IN WINI pr 27 759 AN ITALIAN ITALIANO CLASSE 1 PRODOTTO AL LASER DI CLASSE 1 CLAS
8. Enterprise Mobility Support at http www motorola com enterprisemobility contactsupport For the latest version of this guide go to http www motorola com enterprisemobility manuals Q MOTOROLA Motorola Inc One Motorola Plaza Holtsville New York 11742 USA 1 800 927 9626 http www motorola com enterprisemobility MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the U S Patent and Trademark Office All other product or service names are the property of their registered owners Motorola Inc 2010 WUTC TV ie 72 73950 03 Revision A May 2010
9. SE 2 LUCE LASER SE IKKE IND STRALEN NON FISSARE IL RAGGIOPRODOTTO AL LASER DI CLASSE 2 NORWEGIAN NORSK KLASSE 1 LASERPRODUKT KLASSE 1 KLASSE 2 LASERLYS IKKE STIRR INN LYSSTRALEN LASERPRODUKT KLASSE 2 PORTUGUESE PORTUGUES CLASSE 1 PRODUTO LASER DA CLASSE 1 CLASSE 2 LUZ DE LASER NAO FIXAR O RAIO LUMINOSO PRODUTO LASER DA CLASSE 2 SPANISH ESPANOL CLASE 1 PRODUCTO LASER DE LA CLASE 1 CLASE 2 LUZ LASER NO MIRE FIJAMENTE EL HAZ PRODUIT LASER DE CLASSE 2 SWEDISH SVENSKA KLASS 1 LASERPRODUKT KLASS 1 KLASS 2 LASERLJUS STIRRA INTE MOT STRALEN LASERPRODUKT KLASS 2 lea 158 dol NS 258 AoA Ba O AAS FAHI DNAS 258 AON MS Note Use ONLY a LISTED Motorola Type no 50 14000 5Vdc 2A or PWRS 14000 5Vdc 2A Direct Plug In Power supply marked Class 2 or LPS IEC60950 1 SELV Use of Alternative Power Supply will invalidate any approvals given to this unit and may be dangerous Quick Reference Guide 33 Radio Frequency Interference Requirements FCC Note This equipment has been tested and found to comply FC Testedto compy With the limits for a Class B digital device pursuant to Part 15 roRHomeororriceuse Of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interfer
10. and Electronic Equipment WEEE Bulgarish 3a knueHru ot EC Cneg kpaa Ha nonesHna NM XNBOT BCNYKN NPOAYKTU Tpa6Ba Aa ce BpbarT Ha Motorola 3a peynknnpanHe 3a nu popmayns OTHOCHO BPELLAHETO Ha NpOAYKTM mons otngeTe Ha agpec http www motorola com recycling weee e tina Pro z kazn ky z EU V echny produkty je nutn po skon eni jejich ivotnosti vr tit spole nosti Motorola k recyklaci Informace o zp sobu vr cen produktu najdete na webov str nce http www motorola com recycling weee Dansk Til kunder i EU Alle produkter skal returneres til Motorola til recirkulering n r de er udtjent L s oplysningerne om returnering af produkter p http www motorola com recycling weee Deutsch F r Kunden innerhalb der EU Alle Produkte mussen am Ende ihrer Lebensdauer zum Recycling an Motorola zuruckgesandt werden Informationen zur Rucksendung von Produkten finden Sie unter http www motorola com recycling weee EAAnvika 1a tTeAdtes oTnv E E Oda Ta TIPOIOVTA OTO TEAOG TNG OIGPKEIAG CWS TOUG TTP TTEI va ETTIOTP POVTAI OTHV Motorola yia AVaKUKAWON lIa TIEPIOOOTEPEG TIANPOMOPIES OXETIKA E TNV ETTIOTPOMN EVOG TIPOIOVTOG ETTIOKEPOE TE TH S1IEUBUVON http www motorola com recycling weee oTo AlddikTuo Eesti EL klientidele k ik tooted tuleb nende eluea l ppedes tagastada taaskasutamise eesm rgil Motorola ile Lisainformatsiooni saamiseks toote tagastamise kohta k lastage palun aadressi http www motorola com recyclin
11. ecifications programming and troubleshooting can be found in the LS7808 Product Reference Guide p n 72E 73952 XX Product Description The Symbol LS7808 horizontal slot scanner is a high performance omni directional scanner that supports high throughput applications at the point of sale POS The scanner reads all retail symbologies and has multi interface capability to interface to all popular POS devices The scanner is designed for horizontal in counter mounting and allows slide through scanning of items enhancing productivity and throughput The scanner has an integrated Electronic Article Surveillance EAS antenna for use with Checkpoint EAS systems The LS7808 SR20007TCR features standard tin oxide glass and the LS7808 SR2X009SCR features scratch proof sapphire glass Configurations The Symbol LS7808 is available in the following configurations Configuration Features Symbol LS7808 SR20007TCR_ Standard tin oxide glass window twilight black Checkpoint EAS RoHS compliant Symbol LS7808 SR20009SCR_ Scratch proof sapphire glass window stainless steel bezel top Checkpoint EAS RoHS compliant Symbol LS7808 SR22009SCR_ Scratch proof sapphire glass window stainless steel bezel top Checkpoint EAS RoHS compliant Remote Scanner Management RSM ready out of the box A stainless steel in counter mounting kit p n 12 17206 02R is required for all models See the Mounting Instructions and EAS
12. eeps A successful transmission of buffered data Host Specific USB only 4 short high beeps Scanner has not completed initialization Wait several seconds and scan again Scanner gives a Communication with the bus must be established before power up beep after the scanner can operate at the highest power level scanning a USB Device Type This power up beep The USB bus may put the scanner in a state where power occurs more than to the scanner is cycled on and off more than once This is once normal and usually happens when the PC cold boots RS 232 Host only High beep A lt BEL gt character is received and Beep on lt BEL gt is enabled RS 232 Auxiliary Port only A complete block of data was received and sent to the host either due to a carriage return or because the two second serial response timeout has elapsed High beep A data overrun condition has occurred Abstain from scanning data from other ports when large amounts of data are sent to the RS 232 Auxiliary port 4 long low beeps 10 Symbol LS7808 Horizontal Slot Scanner LED Definitions In addition to beeper sequences the scanner communicates with the user via an LED display The Standard LED Definitions table defines LED indications that display during scanning LED Indication Off No power is applied to the scanner Green The scanner is on and ready to scan Momentary flash A bar code was successfully decoded Slow continuous red flashing gree
13. ence to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Radio Frequency Interference Requirements Canada This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada Marking and European Economic Area EEA Statement of Compliance Symbol hereby declares that this device is in compliance with all the applicable Directives 89 336 EEC 73 23 EEC A Declaration of Conformity may be obtained from http www motorola com doc 34 Symbol LS7808 Horizontal Slot Scanner X Waste Electrical
14. eper Definitions on page 8 Connections The scanner s ports are at the lower edge of the scanner Remove the connection cover to access the ports Secondary Connector Cover EAS Power Port Interlock Auxiliary Port Port Behind Label 6 Symbol LS7808 Horizontal Slot Scanner Routing the Cables The scanner case has several channels to route the outgoing cables so that they are organized and don t hinder the scanner s placement After placing the cable connectors in the appropriate scanner ports route the cables through the nearest channel For a cable with a Y connector containing both power and interface connectors 1 Connect the power and interface cables to the appropriate ports 2 Route the cables according to the following diagram Installing the Scanner The LS7808 mounts in the counter with the face of the scanner flush with the counter top Refer to the LS7808 Product Reference Guide for detailed installation instructions Quick Reference Guide 7 Scanning Bar Codes Install and program the scanner Refer to the LS7808 Product Reference Guide for programming instructions For assistance contact the local supplier or Motorola Enterprise Mobility Support see details on the back cover To scan a bar code 1 Ensure all cable connections are secure 2 Orient the item with the bar code facing the scanner window 3 Move the item through the active scan area see page 8 in the
15. g weee English For EU Customers All products at the end of their life must be returned to Motorola for recycling For information on how to return product please go to http www motorola com recycling weee Espanol Para clientes en la Union Europea todos los productos deberan entregarse a Motorola al final de su ciclo de vida para que sean reciclados Si desea mas informacion sobre como devolver un producto visite http www motorola com recycling weee Fran ais Clients de l Union Europ enne Tous les produits en fin de cycle de vie doivent tre retourn s Motorola pour recyclage Pour de plus amples informations sur le retour de produits consultez http www motorola com recycle weee Italiano per i clienti dell UE tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Motorola al fine di consentirne il riciclaggio Per informazioni sulle modalita di restituzione visitare il seguente sito Web http www motorola com recycling weee Latvie u ES klientiem visi produkti p c to kalpo anas m a beig m ir j nog d atpakal Motorola otrreiz jai p rstr dei Lai ieg tu inform ciju par produktu nog d anu Motorola l dzu skatiet http www motorola com recycling weee Lietuvi ES vartotojams visi gaminiai pasibaigus j eksploatacijos laikui turi b ti gr inti utilizuoti kompanij Motorola Daugiau informacijos kaip gr inti gaminj rasite http www
16. ired bar code cover other bar code on page IBM Table Top USB IBM Hand Held USB For IBM SurePOS 700 Series Quick Reference Guide 27 USB Host Types continued J NOTE When scanning the desired bar code cover other bar code on page OPOS IBM 46XX Host Types ILA None Selected 28 Symbol LS7808 Horizontal Slot Scanner IBM 46XX Host Types continued J NoTE When scanning the desired bar code cover other bar code on page Port 5B Port 9B Quick Reference Guide 29 IBM 46XX Host Types continued J NOTE When scanning the desired bar code cover other bar code on page Port 17 30 Symbol LS7808 Horizontal Slot Scanner Regulatory Information Symbol Technologies Inc the Enterprise Mobility business of Motorola Inc Motorola All Symbol devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required Any changes or modifications to Symbol equipment not expressly approved by Symbol could void the user s authority to operate the equipment Local language translations are available at the following web site http www motorola com enterprisemobility support Health amp Safety Recommendations A Ergonomic Recommendations Caution In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below Consult with your local Health amp Safety Manager to ensure that you are adhering to you
17. n on The scanner is in programming mode Fast continuous red flashing green on There is an internal problem the laser is shut off for regulatory reasons Green on and laser blinking Scanner is in low power blink mode Red and green on Scanner is in low power sleep mode and laser shutdown mode Maintenance Cleaning the exit window is the only maintenance required A dirty or scratched window may affect scanning activity Remove any dirt particles with a damp cloth Wipe the window with a tissue moistened with ammonia or water To clean the exit window 1 Insert a coin into the large screw heads on the front of the scanner and turn counter clockwise 2 Lift off the window 3 Wipe clean the underside of the upper window 4 Wipe clean the top surface of the lower window 5 Re install the top cover by tightening the two large screws To change the exit window 1 Remove the window as described above 2 Replace with a new window 3 Reinstall the top cover by tightening the two large screws Quick Reference Guide Troubleshooting Possible Causes No power to the scanner Problem The omni line scan pattern does not display when you follow the directions for installing the host cable Interface cable is not properly connected Scan line s display Scanner is not but bar code cannot be programmed to read read the bar code type Bar code is damaged Bar code is too far from scanner
18. other bar code on page French Canadian XP 2000 German Quick Reference Guide 19 Country Keyboard Types continued J NOTE When scanning the desired bar code cover other bar code on page Spanish Italian 20 Symbol LS7808 Horizontal Slot Scanner Country Keyboard Types continued J NOTE When scanning the desired bar code cover other bar code on page Swedish UK English Quick Reference Guide 21 Country Keyboard Types continued J NOTE When scanning the desired bar code cover other bar code on page Japanese Brazil Portuguese Windows 22 Symbol LS7808 Horizontal Slot Scanner RS 232 Host Types Standard RS 232 ICL RS 232 Quick Reference Guide 23 RS 232 Host Types continued J NOTE When scanning the desired bar code cover other bar code on page Wincor Nixdorf RS 232 Mode A Wincor Nixdorf RS 232 Mode B 24 Symbol LS7808 Horizontal Slot Scanner RS 232 Host Types continued J NOTE When scanning the desired bar code cover other bar code on page Fujitsu RS 232 OPOS Quick Reference Guide 25 RS 232 Host Types continued J NOTE When scanning the desired bar code cover other bar code on page JPOS USB Host Types J NOTE When scanning the desired bar code cover other bar code on page HID Keyboard Emulation Common Keyboard Wedge Interfacing 26 Symbol LS7808 Horizontal Slot Scanner USB Host Types continued J NOTE When scanning the des
19. r company s safety programs to prevent employee injury e Reduce or eliminate repetitive motion e Maintain a natural position e Reduce or eliminate excessive force e Keep objects that are used frequently within easy reach e Perform tasks at correct heights e Reduce or eliminate vibration e Reduce or eliminate direct pressure e Provide adjustable workstations e Provide adequate clearance e Provide a suitable working environment e Improve work procedures Quick Reference Guide 31 Laser Devices COMPLIES WITH 21CFR1040 10 AND 1040 11 EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE NO 50 DATED JUNE 24 2007 AND IEC 60825 1 Ed 2 0 EN60825 1 2007 The laser classification is marked on one of the labels on the device Class 1 Laser devices are not considered to be hazardous when used for their intended purpose The following statement is required to comply with US and international regulations fl CAUTION Use of controls adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure Class 2 laser scanners use a low power visible light diode As with any very bright light source such as the sun the user should avoid staring directly into the light beam Momentary exposure to a Class 2 laser is not known to be harmful Scanner Labeling IH CLASS 1 LASER PRODUCT J LASER KLASSE 1 APPAREIL LASER DE CLASSE 1 US CLASS Ila LASER PRODUCT AVOID LONG TERM VI
20. reciclare Pentru informatii despre returnarea produsului accesati http www motorola com recycling weee Slovenski Za kupce v EU vsi izdelki se morajo po poteku ivljenjske dobe vrniti podjetju Motorola za recikla o Za informacije o vra ilu izdelka obi ite http www motorola com recycling weee Sloven ina Pre z kazn kov z kraj n EU V etky v robky musia byt po uplynut doby ich ivotnosti vr ten spolo nosti Motorola na recykl ciu Bli ie inform cie o vr ten v robkov n jdete na http www motorola com recycling weee Suomi Asiakkaat Euroopan unionin alueella Kaikki tuotteet on palautettava kierr tett v ksi Motorola yhti n kun tuotetta ei en k ytet Lis tietoja tuotteen palauttamisesta on osoitteessa http www motorola com recycling weee Svenska F r kunder inom EU Alla produkter som uppn tt sin livsl ngd m ste returneras till Motorola f r tervinning Information om hur du returnerar produkten finns p http www motorola com recycling weee T rk e AB M terileri i in Kullan m s resi dolan tum r nler geri d n t rme i in Motorola ya iade edilmelidir r nlerin nas l iade edilece i hakk nda bilgi i in l tfen u adresi ziyaret edin http www motorola com recycling weee Service Information If you have a problem using the equipment contact your facility s Technical or Systems Support If there is a problem with the equipment they will contact the Motorola
21. ve scan area to the scanner does not Motor Sleep mode awaken the unit produce the omni directional scan pattern USB or Synapse host Scanner does not Remove and reinsert external not functioning recognize host power supply to force cable to properly autodetect correct host NOTE f the symbol still does not scan contact distributor or call Motorola Enterprise Mobility Support See the back cover for contact information Quick Reference Guide 13 Programming Generally the technical person in charge of scanning customizes the scanner for the particular application using programming bar codes found in the LS7808 Product Reference Guide p n 72E 73952 XX If the user is programming the scanner consult the LS7808 Product Reference Guide for more information Following are some frequently used programming bar codes NOTE For additional host types refer to the LS7808 Product Reference V4 Guide available at http www motorola com enterprisemobility manuals When scanning the desired bar code cover the other bar code on the page Test To confirm that your scanner is working properly scan the UPC A bar code below Verify the Scanner Is Working 14 Symbol LS7808 Horizontal Slot Scanner Set Defaults J NOTE When scanning the desired bar code cover other bar code on page Scanning this bar code sets all parameters to their factory default values Set Defaults Host Type Selection If a Synapse cable i
Download Pdf Manuals
Related Search