Home

Lenovo ThinkCentre M90

1. 1 e y Figure 19 Installing the optical drive retainer Slide the new optical drive into the drive bay until it snaps into position Chapter 2 Installing or replacing hardware 21 Figure 20 Installing a new optical drive 8 Connect the signal cable and the power cable to the rear of the optical drive What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 32 Replacing the power supply assembly Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the power supply assembly To replace the power supply assembly do the following 1 Turn off the computer and disconnect all power cords from electrical outlets 2 Disconnect the power cords Input Output cables and any other cables that are connected to the computer 3 Remove the four screws at the rear of the chassis that secure the power supply assembly 22 ThinkCentre User Guide Figure 21 Removing the retaining screws for the power supply assembly Open the computer cover See Opening the c
2. e To restore your hard disk drive from a Rescue and Recovery backup or to restore your hard disk drive to the factory default settings click Restore your system and follow the instructions on the screen For more information about the features of the Rescue and Recovery workspace click Help Notes 1 After restoring your hard disk drive to the factory default settings you might have to reinstall device drivers for some devices See Installing or reinstalling device drivers on page 39 2 Some computers come with Microsoft Office or Microsoft Works preinstalled If you need to recover or reinstall your Microsoft Office or Microsoft Works applications you must use the Microsoft Office CD or Microsoft Works CD These discs are provided only with computers preinstalled with Microsoft Office or Microsoft Works Creating and using a rescue medium With a rescue medium such as a disc or a USB hard disk drive you can recover the computer from failures that prevent you from gaining access to the Rescue and Recovery workspace on your hard disk drive Notes 1 The recovery operations you can perform using a rescue medium vary depending on the operating system 2 The rescue disc can be started in all types of optical drives 3 You can also run the PC Doctor for Rescue and Recovery diagnostic program after using a rescue medium to recover the computer from failures and gaining access to the Rescue and Recovery workspace Creating
3. on page 37 Using the Rescue and Recovery workspace The Rescue and Recovery workspace resides in a protected hidden area of your hard disk drive that operates independently from the Windows operating system This enables you to perform recovery operations even if you cannot start the Windows operating system You can perform the following recovery operations from the Rescue and Recovery workspace e Rescue files from your hard disk drive or from a backup The Rescue and Recovery workspace enables you to locate files on your hard disk drive and transfer them to a network drive or other recordable media such as a USB device or a disc This solution is available even if you did not back up your files or if changes were made to the files since your last backup operation You can also rescue individual files from a Rescue and Recovery backup located on your local hard disk drive a USB device or a network drive e Restore your hard disk drive from a Rescue and Recovery backup If you have backed up your hard disk drive using the Rescue and Recovery program you can restore the hard disk drive from a Rescue and Recovery backup even if you cannot start the Windows operating system Chapter 3 Recovery information 37 e Restore your hard disk drive to the factory default settings The Rescue and Recovery workspace enables you to restore the complete contents of your hard disk drive to the factory default settings If you have multiple partitions on
4. 4 Connect a new keyboard or mouse to one of the USB connectors on the computer Depending on where you want to connect the new keyboard or mouse see Locating connectors on the front of your computer on page 6 or Locating connectors on the rear of your computer on page 7 Figure 31 Connecting a new keyboard or mouse What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 32 Completing the parts replacement After completing the installation or replacement for all parts you need to close the computer cover and reconnect cables Depending on the parts you installed or replaced you might need to confirm the updated information in the Setup Utility program Refer to Chapter 4 Using the Setup Utility on page 41 To close the computer cover and reconnect cables to your computer do the following 1 Make sure that all components have been reassembled correctly and that no tools or loose screws are left inside your computer See Locating components on page 8 for the locations of various components in your computer If you have removed the front bezel reinstall it To reinstall the front bezel align the three tabs on the front bezel with the corresponding holes in the chassis and pivot the front bezel inwards until it snaps into position Make sure that the cables are
5. although harmless to you can seriously damage computer components and parts When you handle parts and other computer components take these precautions to avoid static electricity damage e Limit your movement Movement can cause static electricity to build up around you e Always handle parts and other computer components carefully Handle PCI cards memory modules system boards and microprocessors by the edges Never touch any exposed circuitry e Prevent others from touching the parts and other computer components e Before you replace a new part touch the static protective package containing the part to a metal expansion slot cover or other unpainted metal surface on the computer for at least two seconds This reduces static electricity in the package and your body e When possible remove the new part from the static protective packaging and install it directly in the computer without setting the part down When this is not possible place the static protective package that the part came in on a smooth level surface and place the part on it e Do not place the part on the computer cover or other metal surface Installing or replacing hardware This section provides instructions on how to install or replace hardware for your computer You can expand the capabilities of your computer and maintain your computer by installing or replacing hardware Attention Do not open your computer or attempt any repair before reading and
6. non condensing Non operating 20 to 90 non condensing e Altitude Operating 50 to 10 000 ft 15 2 to 3 048 m Non operating 50 to 35 000 ft 15 2 to 10 668 m Electrical input e Input voltage Low range Minimum 100 V ac Maximum 127 V ac Input frequency range 50 to 60 Hz Voltage selection switch setting 115 V ac High range Minimum 200 V ac Maximum 240 V ac Input frequency range 50 to 60 Hz Voltage selection switch setting 230 V ac Software overview This section describes the software preinstalled on the computers that have an internal hard disk drive and an operating system from Lenovo Software provided by Lenovo The following software programs are provided by Lenovo to help you improve productivity and reduce the cost associated with maintaining your computer Software programs provided with your computer might vary depending on your computer model type and preinstalled operating system Lenovo ThinkVantage Tools The Lenovo ThinkVantage Tools program guides you to a host of information sources and provides easy access to various tools to help you work more easily and securely For more information see Lenovo ThinkVantage Tools on page 51 4 ThinkCentre User Guide Note The Lenovo ThinkVantage Tools program is only available on computers with the Windows 7 operating system from Lenovo ThinkVantage Productivity Center The ThinkVantage Productivity Center program guides you
7. reinstalling device drivers 39 replacing battery 17 hard disk drive 18 heat sink 24 Rescue and Recovery 35 workspace Rescue and Recovery 37 Rescue and Recovery workspace 37 resources information 51 S safety vii safety information 52 security cable lock 33 enabling or disabling 42 features 2 33 selecting startup device 43 temporary startup device 43 serial port 8 service and help 53 customer support center 53 getting 51 services other 54 purchasing additional 54 setting password 42 settings changing 41 viewing 41 Setup Utility 41 Setup Utility program starting 41 Setup Utility exiting 43 software recovering 35 solving recovery problems 40 starting the Setup Utility program 41 startup device 43 sequence changing 43 temporary selecting 43 static sensitive devices handling 11 system management 1 programs 45 system board components accessing 12 connectors 9 locating parts 9 locations 9 memory module 13 system fan replacing 27 T television output notice 56 temporary startup device 43 the BIOS updating flashing 45 46 ThinkVantage productivity center 51 trademarks 56 troubleshooting basic 47 troubleshooting diagnostics 47 U updating flashing the BIOS 45 system programs 45 updating flashing the BIOS 46 USB connector 8 using a rescue medium creating and 38 diagnostic programs 53 documentation 53 other services 54 passwords 41 Setup Utility 41 V VGA monitor connector
8. 8 video subsystem 1 viewing and changing settings 41 W warranty information 52 Web site Lenovo 52 workspace backup and recovery 37 Copyright Lenovo 2010 59 60 ThinkCentre User Guide lenovo Part Number 71Y7175 Printed in USA 1P P N 71Y7175
9. Back up your hard drive and select backup operation options 3 Follow the instructions on the screen to complete the backup operation Performing a recovery operation This section provides instructions on how to perform a recovery operation using the Rescue and Recovery program on different operating systems e To perform a recovery operation using the Rescue and Recovery program on the Windows 7 operating system do the following 1 From the Windows desktop click Start gt All Programs gt Lenovo ThinkVantage Tools gt Enhanced Backup and Restore The Rescue and Recovery program opens 2 Inthe Rescue and Recovery main window click the Launch advanced Rescue and Recovery arrow 3 Click the Restore your system from a backup icon 4 Follow the instructions on the screen to complete the recovery operation e To perform a recovery operation using the Rescue and Recovery program on the Windows Vista operating system do the following 1 From the Windows desktop click Start gt All Programs gt ThinkVantage gt Rescue and Recovery The Rescue and Recovery program opens 2 In the Rescue and Recovery main window click Launch advanced Rescue and Recovery 3 Click the Restore your system from a backup icon 4 Follow the instructions on the screen to complete the recovery operation For more information about performing a recovery operation from the Rescue and Recovery workspace see Using the Rescue and Recovery workspace
10. Chapter 2 Installing or replacing hardware 17 Figure 13 Removing the old battery 5 Install a new battery Figure 14 Installing a new battery 6 Close the computer cover and connect the cables See Completing the parts replacement on page 32 Note When the computer is turned on for the first time after replacing the battery an error message might be displayed This is normal after replacing the battery 7 Turn on the computer and all attached devices 8 Use the Setup Utility program to set the date time and any passwords See Chapter 4 Using the Setup Utility on page 41 What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 32 Replacing the hard disk drive Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the hard disk drive if your computer has one For computer models that do not have an internal hard disk drive and use a remote hard disk drive accessed through the SMC Storage Array co
11. also prevent unauthorized use of your computer by a software lock that locks the keyboard until a correct password is typed in Note Make sure that any security cables you installed do not interfere with other computer cables Integrated cable lock An integrated cable lock sometimes referred to as the Kensington lock can be used to secure your computer to a desk table or other non permanent fixture The cable lock attaches to the integrated cable lock slot at the rear of your computer and is operated with a key The cable lock also locks the buttons used to open the computer cover This is the same type of lock used with many notebook computers You can order an integrated cable lock directly from Lenovo by searching for Kensington at http www lenovo com support Chapter 2 Installing or replacing hardware 33 Hi T aie il at hi i NN il i Ht Figure 33 Integrated cable lock Password protection To deter unauthorized use of your computer you can use the Setup Utility program to set a password When you turn on your computer you are prompted to type the password The computer cannot be used until a valid password is typed in Refer to Chapter 4 Using the Setup Utility on page 41 for more information Erasing lost or forgotten passwords clearing CMOS This section provides instructions on how to erase lost or forgotten passwords such as a user password To erase a l
12. audio and USB assembly Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the front audio and USB assembly To replace the front audio and USB assembly do the following 1 Turn off the computer and disconnect all power cords from electrical outlets 2 Open the computer cover See Opening the computer cover on page 12 3 Pivot the optical drive bay assembly upward to gain access to the front audio and USB assembly See Accessing the system board components and drives on page 12 4 Locate the front audio and USB assembly 5 Disconnect the front audio and USB assembly cables from the system board See Locating parts on the system board on page 9 Note Make sure you note the locations of the cables when you disconnect the cables from the system board 6 Remove the screw that secures the front audio and USB assembly to the chassis Figure 25 Removing the securing screw of the front audio and USB assembly 7 Remove the front audio and USB assembly from the chassis 8 Install a new front audio and USB assembly into the chassis and align the screw hole in the front audio and USB assembly with the h
13. com support This section provides instructions on how to install or replace a PCI card Your computer has one standard PCI card slot and one PCI Express x16 graphics card slot To install or replace a PCI card do the following 1 2 3 4 Turn off the computer and disconnect all power cords from electrical outlets Open the computer cover See Opening the computer cover on page 12 Rotate the PCI card retainer to the open position If you are installing a PCI card remove the appropriate metal slot cover If you are replacing an old PCI card grasp the old card that is currently installed and gently pull it out of the slot Chapter 2 Installing or replacing hardware 15 Figure 11 Removing a PCI card Notes a The card fits tightly into the card slot If necessary alternate moving each side of the card a small amount until it is removed from the card slot b If the card is held in place by a retaining latch press the card retaining latch jas shown to disengage the latch Grasp the card and gently pull it out of the slot 5 Remove the new PCI card from its static protective package 6 Install the new card into the appropriate card slot on the system board and rotate the card retainer to the closed position See Locating parts on the system board on page 9 16 ThinkCentre User Guide Figure 12 Installing the PCI card What to do next e To wor
14. how to install the device driver Solving recovery problems If you are unable to access the Rescue and Recovery workspace or the Windows environment do one of the following e Use a rescue medium to start the Rescue and Recovery workspace See Creating and using a rescue medium on page 38 e Use recovery media if all other methods of recovery have failed and you need to restore the hard disk drive to the factory default settings See Creating and using recovery media on page 35 Note If you are unable to access the Rescue and Recovery workspace or the Windows environment from a rescue medium a recovery repair diskette or recovery media you might not have the rescue device an internal hard disk drive a disc a USB hard disk drive or other external devices set as the first boot device in the startup device sequence You must first make sure that your rescue device is set as the first boot device in the startup device sequence in the Setup Utility program See Selecting a startup device on page 43 for detailed information about temporarily or permanently changing the startup device sequence For more information about the Setup Utility program see Chapter 4 Using the Setup Utility on page 41 It is important to create a rescue medium a recovery repair diskette and a set of recovery media as early as possible and store them in a safe place for future use 40 ThinkCentre User Guide Chapter 4 Using the Se
15. key when turning on the computer When you hear beeps or see a logo screen stop pressing the F11 key The Rescue and Recovery workspace opens after a short delay 3 From the Rescue and Recovery workspace select Launch advanced Rescue and Recovery gt Diagnose hardware The PC Doctor for Rescue and Recovery diagnostic program opens 4 Select the diagnostic test you want to run Then follow the instructions on the screen For additional information about running the PC Doctor for Rescue and Recovery diagnostic program refer to the PC Doctor for Rescue and Recovery help system Note If you encounter failures that prevent you from gaining access to the Rescue and Recovery workspace you can run the PC Doctor for Rescue and Recovery diagnostic program after using a rescue medium to recover the computer from failures and gaining access to the Rescue and Recovery workspace See Creating and using a rescue medium on page 38 PC Doctor for DOS You can also download the latest version of the PC Doctor for DOS diagnostic program from http www lenovo com support The PC Doctor for DOS diagnostic program runs independently of the Windows operating system Use the PC Doctor for DOS diagnostic program if you are unable to start the Windows operating system or if the two diagnostic programs preinstalled on your computer have not been successful in isolating a possible problem You can run the PC Doctor for DOS diagnostic program from a diagnostic
16. program helps you maintain your computer improve computing security diagnose computer problems get familiar with the innovative technologies provided by Lenovo and get more information about your computer You can use the diagnostics feature of the Lenovo ThinkVantage Toolbox program to test devices diagnose computer problems create bootable diagnostic media update system drivers and view system information e To run the Lenovo ThinkVantage Toolbox program on the Windows 7 operating system click Start gt All Programs Lenovo ThinkVantage Tools gt System Health and Diagnostics Follow the instructions on the screen e To run the Lenovo ThinkVantage Toolbox program on the Windows Vista operating system click Start gt All Programs gt ThinkVantage gt Lenovo ThinkVantage Toolbox Follow the instructions on the screen Follow the instructions on the screen For additional information refer to the Lenovo ThinkVantage Toolbox help system 48 ThinkCentre User Guide PC Doctor for Rescue and Recovery The PC Doctor for Rescue and Recovery diagnostic program is part of the Rescue and Recovery workspace on each Lenovo computer Use the PC Doctor for Rescue and Recovery diagnostic program if you are unable to start the Windows operating system To run the PC Doctor for Rescue and Recovery diagnostic program from the Rescue and Recovery workspace do the following 1 Turn off the computer 2 Repeatedly press and release the F11
17. user name is not logged on in another location The SMC login prompt Verify that your computer does not turn off due to inactivity SMC will automatically disappears before you log turn off an inactive computer If your computer turns off automatically turn on the on and then a black screen computer and log on Contact your administrator if you cannot correct the problem displays for SMC computers only The computer beeps multiple Verify that no keys are stuck times before the operating system starts Diagnostic programs Diagnostic programs are used to test hardware components of your computer and report operating system controlled settings that can cause hardware failures There are two programs preinstalled on your computer to help you diagnose computer problems e Lenovo ThinkVantage Toolbox used when you are running the Windows operating system e PC Doctor for Rescue and Recovery used when your Windows operating system does not start Notes 1 You can also download the PC Doctor for DOS diagnostic program from http www lenovo com support See PC Doctor for DOS on page 49 for detailed information 2 If you are unable to isolate and repair the problem yourself after running the diagnostic programs save and print the log files created by the diagnostic programs You will need the log files when you speak to a Lenovo technical support representative Lenovo ThinkVantage Toolbox The Lenovo ThinkVantage Toolbox
18. you have created e If you have created a rescue medium using a disc use the following instructions to use the rescue medium 1 Turn off your computer 2 Repeatedly press and release the F12 key when turning on the computer When the Please select boot device window opens release the F12 key 3 In the Please select boot device window select the desired optical drive as the first boot device Then insert the rescue disc into the optical drive and press Enter The rescue medium starts e If you have created a rescue medium using a USB hard disk drive use the following instructions to use the rescue medium 1 Attach the USB hard disk drive to one of the USB connectors on your computer 2 Repeatedly press and release the F12 key when turning on the computer When the Please select boot device window opens release the F12 key 3 In the Please select boot device window select the USB hard disk drive as the first boot device and press Enter The rescue medium starts When the rescue medium starts the Rescue and Recovery workspace opens The help information for each feature is available from the Rescue and Recovery workspace Follow the instructions to complete the recovery process Installing or reinstalling device drivers Before installing or reinstalling device drivers make sure that you have a preinstalled operating system and the documentation and software media for the device Device drivers for factory installed devi
19. your hard disk drive you have the option to restore the factory default settings to the C partition and leave the other partitions intact Because the Rescue and Recovery workspace operates independently from the Windows operating system you can restore the factory default settings even if you cannot start the Windows operating system Attention If you restore the hard disk drive from a Rescue and Recovery backup or restore the hard disk drive to the factory default settings all files on the primary hard disk drive partition usually drive C will be deleted in the recovery process If possible make copies of important files If you are unable to start the Windows operating system you can use the rescue files feature of the Rescue and Recovery workspace to copy files from your hard disk drive to other media To start the Rescue and Recovery workspace do the following 1 Make sure the computer is turned off 2 Repeatedly press and release the F11 key when turning on the computer When you hear beeps or see a logo screen release the F11 key 3 If you have set a Rescue and Recovery password type your password when prompted The Rescue and Recovery workspace opens after a short delay Note If the Rescue and Recovery workspace fails to open see Solving recovery problems on page 40 4 Do one of the following e To rescue files from your hard disk drive or from a backup click Rescue files and follow the instructions on the screen
20. a rescue medium This section provides instructions on how to create a rescue medium on different operating systems 38 ThinkCentre User Guide e To create a rescue medium on the Windows 7 operating system do the following 1 From the Windows desktop click Start gt All Programs gt Lenovo ThinkVantage Tools gt Enhanced Backup and Restore The Rescue and Recovery program opens N In the Rescue and Recovery main window click the Launch advanced Rescue and Recovery arrow o Click the Create Rescue Media icon The Create Rescue and Recovery Media window opens 4 Inthe Rescue Media area select the type of the rescue medium you want to create You can create a rescue medium using a disc a USB hard disk drive or a secondary internal hard disk drive 5 Click OK and follow the instructions on the screen to create a rescue medium e To create a rescue medium on the Windows Vista operating system do the following 1 From the Windows desktop click Start gt All Programs gt ThinkVantage gt Create Recovery Media The Create Rescue and Recovery Media window opens 2 Inthe Rescue Media area select the type of the rescue medium you want to create You can create a rescue medium using a disc a USB hard disk drive or a secondary internal hard disk drive 3 Click OK and follow the instructions on the screen to create a rescue medium Using a rescue medium This section provides instructions on how to use the rescue medium
21. ake on LAN Wake on Ring Windows Management Instrumentation WMI Input Output I O features 9 pin serial port one standard and one optional Eight Universal Serial Bus USB connectors two on the front panel and six on the rear panel Ethernet connector One DisplayPort connector not applicable on some models One VGA monitor connector not applicable on some models One Personal System 2 PS 2 keyboard connector optional One PS 2 mouse connector optional Three audio connectors on the rear panel audio line in connector audio line out connector and microphone connector Two audio connectors on the front panel microphone connector and headphone connector For more information see Locating connectors on the front of your computer on page 6 and Locating connectors on the rear of your computer on page 7 Expansion One hard disk drive bay One optical drive bay One PCI card slot One PCI Express x16 graphics card slot Power supply 240 watt auto sensing power supply Security features Computrace Cover presence switch also called intrusion switch Enabling or disabling a device Enabling or disabling USB connectors individually Hard disk drive password Keyboard with fingerprint reader shipped with some models ThinkCentre User Guide e Power on password POP and Administrator Password for BIOS access e Startup sequence control e Startup without keyboard or mouse e Support for an int
22. and Recovery workspace on each Lenovo computer to diagnose hardware problems and report operating system controlled settings that can cause hardware failures Use the PC Doctor for Rescue and Recovery diagnostic program if you are unable to start the Windows operating system See PC Doctor for Rescue and Recovery on page 49 for more information Adobe Reader The Adobe Reader program is a tool used to view print and search PDF documents See Online Books folder on page 51 for more information about accessing the online books and the Lenovo Web site Antivirus software Your computer comes with antivirus software that you can use to detect and eliminate viruses Lenovo provides a full version of antivirus software on your hard disk drive with a free 30 day subscription After 30 days you must renew the license to continue receiving the antivirus program updates Locations Locating connectors on the front of your computer Front connector locations shows the locations of the connectors on the front of your computer Figure 1 Front connector locations USB connector EJ Microphone connector E Headphone connector EJ USB connector 6 ThinkCentre User Guide Locating connectors on the rear of your computer Rear connector locations shows the locations of the connectors on the rear of your computer Some connectors on the rear of your computer are color coded to help you determine where to connect the cables on your c
23. apter 7 Getting information help and service 53 Note Phone numbers are subject to change without notice If the number for your country or region is not provided contact your Lenovo reseller or Lenovo marketing representative If possible be at your computer when you call Have the following information available e Machine type and model e Serial numbers of your hardware products e Description of the problem e Exact wording of any error messages e Hardware and software configuration information Using other services If you travel with your computer or relocate it to a country where your desktop or notebook computer machine type is sold your computer might be eligible for International Warranty Service which automatically entitles you to obtain warranty service throughout the warranty period Service will be performed by service providers authorized to perform warranty service Service methods and procedures vary by country and some services might not be available in all countries International Warranty Service is delivered through the method of service such as depot carry in or on site service that is provided in the servicing country Service centers in certain countries might not be able to service all models of a particular machine type In some countries fees and restrictions might apply at the time of service To determine whether your computer is eligible for International Warranty Service and to view a list of the coun
24. asks customizing settings for your personal preference protecting data expanding and upgrading and troubleshooting Note The Access Help information system is only available on computers that have an internal hard disk drive and preinstalled software from Lenovo e To open the Access Help information system on the Windows 7 operating system click Start gt Help and Support gt Lenovo Access Help e To open the Access Help information system on the Windows Vista operating system click Start gt All Programs gt ThinkVantage gt Access Help After you have opened the Access Help information system use the left panel to make a selection from the Contents tab or the Index tab or use the Search tab to find a particular word or phrase Safety and Warranty The ThinkCentre Safety and Warranty Guide that is provided with your computer contains information on safety setup warranty and notices Read and understand all safety information before using this product Lenovo Web site http www lenovo com The Lenovo Web site provides up to date information and services to help you buy upgrade and maintain your computer You can also do the following e Shop for desktop and notebook computers monitors projectors upgrades and accessories for your computer and special offers e Purchase additional services such as support for hardware operating systems application programs network setup and configuration and custom installati
25. bay assembly upward to gain access to the memory slots See Accessing the system board components and drives on page 12 4 Locate the memory slots See Locating parts on the system board on page 9 Chapter 2 Installing or replacing hardware 13 5 Remove any parts that might prevent access to the memory slots 6 Open the retaining clips Figure 8 Opening the retaining clips If you are replacing an old memory module open the retaining clips and gently pull the memory module out of the memory slot Figure 9 Removing a memory module 7 Position the new memory module over the memory slot Make sure that the notch Jj on the memory module aligns correctly with the slot key jon the system board Push the memory module straight down into the slot until the retaining clips close 14 ThinkCentre User Guide Figure 10 Installing a memory module What to do next To work with another piece of hardware go to the appropriate section To complete the installation or replacement go to Completing the parts replacement on page 32 nstalling or replacing a PCI card Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo
26. ces are located on the computer hard disk drive usually drive C in the SWTOOLS DRIVERS subdirectory The latest device drivers for factory installed devices are also available at http www lenovo com support Other device drivers are on the software media that come with individual devices To install or reinstall the device driver for a factory installed device do the following 1 Turn on the computer Chapter 3 Recovery information 39 2 Use Windows Explorer or My Computer to display the directory structure of your hard disk drive 3 Go to the C SWTOOLS directory 4 Open the DRIVERS folder Within the DRIVERS folder there are several subfolders named for various devices installed in your computer such as AUDIO or VIDEO 5 Open the appropriate device subfolder 6 Do one of the following e Inthe device subfolder look for a SETUP exe file Double click the file and follow the instructions on the screen to complete the installation e Inthe device subfolder look for a README txt file or a file with the txt extension This file might be named after the operating system such as WIN98 txt The TXT file contains information about how to install the device driver Follow the instructions to complete the installation e If the device subfolder contains a file with the inf extension and you want to install the device driver using the INF file refer to your Windows Help and Support information system for detailed information about
27. ction provides instructions on how to replace the internal speaker Note Not all computers have the internal speaker To replace the internal speaker do the following 28 ThinkCentre User Guide 1 Turn off the computer and disconnect all power cords from electrical outlets 2 Open the computer cover See Opening the computer cover on page 12 3 Remove the front bezel by releasing the three plastic tabs and pivoting the front bezel outward Figure 28 Removing the front bezel 4 Pivot the optical drive bay assembly upward to gain access to the internal speaker See Accessing the system board components and drives on page 12 5 Locate the internal speaker See Locating components on page 8 6 Disconnect the internal speaker cable and the thermal sensor cable from the internal speaker connector and the thermal sensor connector on the system board See Locating parts on the system board on page 9 7 Push the two tabs J on the bottom of the internal speaker as shown to release the internal speaker and then lift the internal speaker up to completely remove it from the chassis Chapter 2 Installing or replacing hardware 29 Figure 29 Removing the internal speaker 8 Remove the attached thermal sensor cable from the old internal speaker and install it on the new internal speaker 9 Insert the two tabs J on the bottom of the new internal speaker into the correspondin
28. ctors on ithe rear af your computer Locating components Locating parts on the system board Locating internal drives Chapter 2 Installing or replacing hardware ee Handling static sensitive devices Installing or replacing hardware Installing external options Opening the computer cover Accessing the em board components and drives ove aan Installing or repkictig a memory modile Installing or replacing a PCI card Replacing the battery Replacing the hard disk drive Replacing the optical drive Replacing the power supply assembly Replacing the heat sink Replacing the front audio and USB assembly Replacing the system jani Replacing the internal speaker Replacing the keyboard or mouse Completing the parts replacement Installing security features Integrated cable lock Password protection Erasing lost or forgotten passwords clearing CMOS a ap Le ws se a ee GD Chapter 3 Recovery information Creating and using recovery media Creating recovery media Copyright Lenovo 2010 vii OoornrR Rw O O ON 11 11 11 11 12 12 13 15 17 18 20 22 24 26 27 28 31 32 33 33 34 34 35 35 35 Using recovery media de Sg Performing backup and recovery operations Performing a backup operation Performing a recovery operation Using the Rescue and Recovery workspace Creating and using a rescue medium Creating a rescue medium Using a rescue medium i Ins
29. disc that you created Creating a diagnostic disc This section provides instructions on how to create a diagnostic disc To create a diagnostic disc do the following 1 Download a self starting bootable CD DVD image known as an ISO image of the diagnostic program from http www lenovo com support 2 Use any CD DVD burning software to create a diagnostic disc with the ISO image Running the diagnostic program from a diagnostic disc This section provides instructions on how to run the diagnostic program from a diagnostic disc that you created To run the diagnostic program from a diagnostic disc that you created do the following 1 Make sure the optical drive you want to use is set as the first boot device in the startup device sequence See Selecting a startup device on page 43 2 Make sure the computer is turned on and then insert the disc into the optical drive The diagnostic program opens Chapter 6 Troubleshooting and diagnostics 49 Note You can insert the disc into the optical drive when you are setting the startup device sequence However if you insert the disc into the optical drive when you have already entered the operating system you need to restart the computer to access the diagnostic program Follow the instructions on the screen to select the diagnostic test you want to run Note For additional help press the F1 key 4 Remove the diagnostic disc from the optical drive when you complete the d
30. e This product incorporates copyright protection technology that is protected by method claims of certain U S patents and other intellectual property rights owned by Macrovision Corporation and other rights owners Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation Reverse engineering or disassembly is prohibited European conformance CE mark CE Trademarks The following terms are trademarks of Lenovo in the United States other countries or both Lenovo The Lenovo logo Personal System 2 PS 2 Rescue and Recovery ThinkCentre ThinkVantage Microsoft Windows and Windows Vista are trademarks of the Microsoft group of companies Intel Intel Core and Pentium are trademarks of Intel Corporation in the United States other countries or both Linux is a trademark of Linus Torvalds in the United States other countries or both Other company product or service names may be trademarks or service marks of others 56 ThinkCentre User Guide Index A a rescue medium creating and using 38 Administrator password 42 antivirus software 6 audio line in connector 7 audio line out connector 7 audio subsystem 1 backup and recovery operations 36 basic troubleshooting 47 battery replacing 17 boot block recovery 46 C cable lock security 33 cables con
31. e 8 6 Disconnect the system fan cable from the microprocessor fan connector on the system board See Locating parts on the system board on page 9 7 Release the four tabs on the bottom of the system fan as shown and then lift the system fan straight up to completely remove it from the chassis Chapter 2 Installing or replacing hardware 27 Figure 27 Removing the system fan 8 Align the four tabs on the bottom of the new system fan with the corresponding holes in the chassis and push the new system fan straight down until it snaps into position 9 Connect the system fan cable to the microprocessor fan connector on the system board See Locating parts on the system board on page 9 10 To reinstall the front bezel align the three tabs on the front bezel with the corresponding holes in the chassis and pivot the front bezel inwards until it snaps into position What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 32 Replacing the internal speaker Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This se
32. e disc or an update program that can be run from the operating system Updating flashing the BIOS from a disc This section provides instructions on how to update flash the BIOS from a disc Note You can download a self starting bootable disc image known as an ISO image with the system program updates to create a system program update disc Go to http www lenovo com support To update flash the BIOS from a disc do the following 1 Turn off your computer 2 Repeatedly press and release the F12 key when turning on the computer When the Startup Device Menu opens release the F12 key 3 On the Startup Device Menu select the desired optical drive as the startup device Then insert the disc into this optical drive and press Enter The update begins 4 When prompted to change the serial number it is suggested that you do not make this change by pressing N However if you do want to change the serial number press Y then type in the serial number and press Enter 5 When prompted to change the machine type and model it is suggested that you do not make this change by pressing N However if you do want to change the machine type and model press Y then type in the machine type and model and press Enter 6 Follow the instructions on the screen to complete the update After the update is completed remove the disc from the optical drive Copyright Lenovo 2010 45 Updating flashing the BIOS from your operatin
33. e size varies by model type e Intel Core i3 microprocessor e Intel Core i5 microprocessor e Intel Core i7 microprocessor e Intel Pentium microprocessor Memory e Supports up to four double data rate 3 dual inline memory modules DDR3 DIMMs Internal drives e Optical drive e Serial Advanced Technology Attachment SATA internal hard disk drive installed in some models Video subsystem e Integrated graphics card for a Video Graphics Array VGA connector and a DisplayPort connector not applicable on some models e Peripheral Component Interconnect PCI Express x16 graphics card slot on the system board for a discrete graphics card Audio subsystem e Integrated high definition HD audio e Audio line in connector audio line out connector and microphone connector on the rear panel e Microphone connector and headphone connector on the front panel e Internal speaker installed in some models Connectivity e 100 1000 Mbps integrated Ethernet controller e PCI Fax modem some models System management features Copyright Lenovo 2010 1 Ability to store power on self test POST hardware test results Automatic power on startup Desktop Management Interface DMI Intel Active Management Technology AMT available on some models Intel Matrix Storage Manager Preboot Execution Environment PXE Secure Managed Client SMC some models System Management SM Basic Input Output System BIOS and SM software W
34. ected to the monitor and to the appropriate monitor connector on the computer The monitor power cord is correctly connected to the monitor and to a working electrical outlet The monitor is turned on and the brightness and contrast controls are set correctly The computer voltage matches the voltage available at the electrical outlet for your country or region If your computer has two monitor connectors be sure to use the connector on the graphics card The keyboard does not work Verify that e The computer is turned on e The keyboard is securely connected to a USB connector on the computer e No keys are stuck The mouse does not work Verify that e The computer is turned on e The mouse is securely connected to a USB connector on the computer e The mouse is clean Refer to Cleaning an optical mouse on page 50 for further information Copyright Lenovo 2010 47 symptom dC The operating system does not Verify that sian e The startup sequence includes the device where the operating system resides Usually the operating system is on the hard disk drive For more information see Selecting a startup device on page 43 Note For SMC computers you might receive the error message No operating system found Press F1 to repeat boot sequence In this case press Ctrl Alt Delete instead of F1 to establish a connection to the storage area network where your operating system is stored Verify that the
35. ed to type a valid password each time you try to access the Setup Utility program The Setup Utility program cannot be accessed until a valid password is typed in If both the Power On Password and Administrator Password are set you can type either password However you must use your Administrator Password to change any configuration settings Hard Disk Password Setting a Hard Disk Password prevents unauthorized access to the data on the hard disk drive When a Hard Disk Password is set you are prompted to type a valid password each time you try to access the hard disk drive Setting changing and deleting a password To set change or delete a password do the following 1 Start the Setup Utility program See Starting the Setup Utility program on page 41 2 From the Setup Utility program main menu select Security 3 Depending on the password type select Set Power On Password Set Administrator Password or Hard Disk Password 4 Follow the instructions on the right side of the screen to set change or delete a password Note A password can be any combination of up to 64 alphabetic and numeric characters For more information see Password considerations on page 41 Enabling or disabling a device This section provides information on how to enable or disable user access to the following devices USB Setup Use this option to enable or disable a USB connector When a USB connector is disabled the device connected
36. egrated cable lock Kensington lock e Trusted Platform Module TPM Preinstalled software programs Your computer is preinstalled with some software programs to help you work more easily and securely For more information see Software overview on page 4 Preinstalled operating system Your computer is preinstalled with one of the following operating systems e Microsoft Windows 7 e Microsoft Windows Vista Operating system s certified or tested for compatibility varies by model type e Linux Specifications This section lists the physical specifications for your computer 1 The operating system s listed here are being certified or tested for compatibility at the time this publication goes to press Additional operating systems might be identified by Lenovo as compatible with your computer following the publication of this manual This list is subject to change To determine if an operating system has been certified or tested for compatibility check the Web site of the operating system vendor Chapter 1 Product overview 3 Dimensions Width 317 mm 12 48 inches Height 99 mm 3 9 inches Depth 355 mm 13 98 inches Weight Maximum configuration as shipped 7 5 kg 16 53 Ibs Environment e Air temperature Operating 10 C to 35 C 50 F to 95 F Non operating 40 C to 60 C 40 F to 140 F Non operating 10 C to 60 C 14 F to 140 F without package e Humidity Operating 20 to 80
37. en the computer cover CAUTION A Turn off the computer and wait three to five minutes to let the computer cool before opening the computer cover To open the computer cover do the following 1 Remove any media from the drives and turn off all attached devices and the computer 2 Disconnect all power cords from electrical outlets 3 Disconnect the power cords Input Output cables and any other cables that are connected to the computer See Locating connectors on the front of your computer on page 6 and Locating connectors on the rear of your computer on page 7 4 Remove any locking device that secures the computer cover such as an integrated cable lock See Integrated cable lock on page 33 5 Press the cover release buttons on the sides of the computer and pivot the computer cover upward Figure 6 Opening the computer cover Accessing the system board components and drives This section provides instructions on how to access the system board components and drives To access the system board components and drives do the following 1 Turn off the computer and disconnect all power cords from electrical outlets 2 Open the computer cover See Opening the computer cover on page 12 3 Pivot the optical drive bay assembly upward to access the internal components On some models you might need to remove the hard disk drive to access some internal components See Replacing the hard disk drive on pa
38. er e On an attached external USB hard disk drive e Ona network drive e On recordable discs a recordable optical drive is required for this option After you have backed up the contents on the hard disk drive you can restore the complete contents of the hard disk drive restore only the selected files or restore only the Windows operating system and applications Performing a backup operation This section provides instructions on how to perform a backup operation using the Rescue and Recovery program on different operating systems e To perform a backup operation using the Rescue and Recovery program on the Windows 7 operating system do the following 1 From the Windows desktop click Start gt All Programs gt Lenovo ThinkVantage Tools gt Enhanced Backup and Restore The Rescue and Recovery program opens 36 ThinkCentre User Guide 2 Inthe Rescue and Recovery main window click the Launch advanced Rescue and Recovery arrow 3 Click Back up your hard drive and select backup operation options Then follow the instructions on the screen to complete the backup operation e To perform a backup operation using the Rescue and Recovery program on the Windows Vista operating system do the following 1 From the Windows desktop click Start gt All Programs gt ThinkVantage gt Rescue and Recovery The Rescue and Recovery program opens 2 In the Rescue and Recovery main window click Launch advanced Rescue and Recovery gt
39. es that are connected to the computer 2 Open the computer cover See Opening the computer cover on page 12 Access the system board See Accessing the system board components and drives on page 12 Locate the Clear CMOS Recovery jumper on the system board See Locating parts on the system board on page 9 Remove any cables that impede access to the Clear CMOS Recovery jumper Move the jumper from the standard position pin 1 and pin 2 to the maintenance position pin 2 and pin 3 Reconnect any cables that were disconnected and reinstall the hard disk drive if removed A gt O CONDO Close the computer cover and reconnect the power cords for the computer and monitor to electrical outlets See Completing the parts replacement on page 32 9 Turn on the computer and then insert the POST and BIOS update flash update disc into the optical drive The recovery session begins The recovery session will take two to three minutes During this time you will hear a series of beeps 10 After the recovery session is completed the series of beeps will end and the system will automatically turn off Remove the disc from the optical drive before the system completely turns off 11 Repeat step 1 through step 4 12 Move the Clear CMOS Recovery jumper back to the standard position pin 1 and pin 2 13 Reconnect any cables that were disconnected and reinstall the hard disk drive if removed 14 Close the compu
40. eyboards or the audio line in connector on a stereo system or other external recording device Chapter 1 Product overview 7 Connector DisplayPort connector Ethernet connector Microphone connector Serial port PS 2 keyboard connector optional PS 2 mouse connector optional USB connector VGA monitor connector Locating components Description Used to attach a high performance monitor a direct drive monitor or other devices that use a DisplayPort connector Used to attach an Ethernet cable for a local area network LAN Note To operate the computer within FCC Class B limits use a Category 5 Ethernet cable Used to attach a microphone to your computer when you want to record sound or if you use speech recognition software Used to attach an external modem a serial printer or other devices that use a 9 pin serial port Used to attach a keyboard that uses a PS 2 keyboard connector Used to attach a mouse a trackball or other pointing devices that use a PS 2 mouse connector Used to attach a device that requires a USB connector such as a USB keyboard a USB mouse a USB scanner or a USB printer If you have more than eight USB devices you can purchase a USB hub which you can use to connect additional USB devices Used to attach a VGA monitor or other devices that use a VGA monitor connector Figure 3 Component locations on page 8 shows the locations of the various components in your compute
41. fications or warranties Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Lenovo or third parties All information contained in this document was obtained in specific environments and is presented as an illustration The result obtained in other operating environments may vary Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you Any references in this publication to non Lenovo Web sites are provided for convenience only and do not in any manner serve as an endorsement of those Web sites The materials at those Web sites are not part of the materials for this Lenovo product and use of those Web sites is at your own risk Any performance data contained herein was determined in a controlled environment Therefore the result obtained in other operating environments may vary significantly Some measurements may have been made on development level systems and there is no guarantee that these measurements will be the same on generally available systems Furthermore some measurements may have been estimated through extrapolation Actual results may vary Users of this document should verify the applicable data for their specific environment Copyright Lenovo 2010 55 Television output notice The following notice applies to models that have the factory installed television output featur
42. g holes in the chassis and push the speaker straight down until the other two tabs J snap into position 30 ThinkCentre User Guide Figure 30 Installing the new internal speaker 10 Reconnect the internal speaker cable and the thermal sensor cable to the system board See Locating parts on the system board on page 9 11 To reinstall the front bezel align the three tabs on the front bezel with the corresponding holes in the chassis and pivot the front bezel inwards until it snaps into position What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 32 Replacing the keyboard or mouse Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the keyboard or mouse To replace the keyboard or mouse do the following 1 Remove any media from the drives Then turn off all attached devices and the computer 2 Disconnect all power cords from electrical outlets 3 Disconnect the old keyboard cable or mouse cable from the computer Chapter 2 Installing or replacing hardware 31
43. g system Note Because Lenovo makes constant improvements to its Web sites the Web page contents are subject to change without notice including the contents referenced in the following procedure To update flash the BIOS from your operating system do the following 1 Go to http www lenovo com support 2 Do the following to locate the downloadable files for your machine type a Inthe Enter a product number field type your machine type and click Go b Click Downloads and drivers c Select BIOS from the Refine results drop down list box to easily locate all the BIOS related links d Click the BIOS update link 3 Click the TXT file that contains the instructions for updating flashing the BIOS from your operating system 4 Print these instructions This is very important because these instructions will not be displayed on the screen after the download begins 5 Follow the printed instructions to download extract and install the update Recovering from a POST BIOS update failure If the power to your computer is interrupted while the POST and BIOS is being updated your computer might not restart correctly If this happens perform the following procedure to recover from the POST and BIOS update failure This procedure is commonly called Boot block Recovery 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cabl
44. g system do the following 1 Depending on the type of your recovery media connect the boot medium memory key or other USB storage device to the computer or insert the boot disc into the optical drive 2 Repeatedly press and release the F12 key when turning on the computer When the Please select boot device window opens release the F12 key 3 Select the desired startup device and press Enter The restore process begins 4 Follow the instructions on the screen to complete the operation Notes 1 After restoring your computer to the factory default settings you might have to reinstall device drivers for some devices See Installing or reinstalling device drivers on page 39 2 Some computers come with Microsoft Office or Microsoft Works preinstalled If you need to recover or reinstall your Microsoft Office or Microsoft Works applications you must use the Microsoft Office CD or Microsoft Works CD These discs are provided only with computers preinstalled with Microsoft Office or Microsoft Works Performing backup and recovery operations The Rescue and Recovery program enables you to back up all your hard disk drive contents including the operating system data files software programs and personal settings You can designate where the Rescue and Recovery program stores the backup e Ina protected area of your hard disk drive e On the secondary hard disk drive if a secondary hard disk drive is installed in your comput
45. ge 18 12 ThinkCentre User Guide Notes a Make sure you note the locations of any cables that you disconnect from the drives or the system board b Make sure the hard disk drive assembly is in the latched down position before closing the computer cover to prevent damage to the hard disk drive Figure 7 Pivoting the optical drive bay assembly Installing or replacing a memory module Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to install or replace a memory module Your computer has four slots for installing or replacing DDR3 DIMMs that provide up to a maximum of 16 GB system memory When installing or replacing a memory module use the following guidelines e Use 1 GB 2 GB or 4 GB DDR3 DIMMs in any combination up to a maximum of 16 GB e Install memory modules in the sequence of DIMM 1 DIMM 3 DIMM 2 and DIMM 4 See Locating parts on the system board on page 9 To install or replace a memory module do the following 1 Turn off the computer and disconnect all power cords from electrical outlets 2 Open the computer cover See Opening the computer cover on page 12 3 Pivot the optical drive
46. hrough the Customer Support Center The following services are available during the warranty period e Problem determination Trained service personnel are available to assist you with determining a hardware problem and deciding what action is necessary to fix the problem e Hardware repair If the problem is caused by hardware under warranty trained service personnel are available to provide the applicable level of service e Engineering Change management There might be changes that are required after a product has been sold Lenovo or your reseller will make selected Engineering Changes ECs that apply to your hardware available These items are not covered by the warranty Replacement or use of parts not manufactured for or by Lenovo or non warranted Lenovo parts Identification of software problem sources Configuration of BIOS as part of an installation or upgrade Changes modifications or upgrades to device drivers Installation and maintenance of network operating systems NOS Installation and maintenance of application programs Refer to the ThinkCentre Safety and Warranty Guide that comes with your computer for a complete explanation of warranty terms You must retain your proof of purchase to obtain warranty service For a list of the Lenovo Support phone numbers for your country or region go to http www lenovo com support phone or refer to the ThinkCentre Safety and Warranty Guide that comes with your computer Ch
47. iagnostic process Cleaning an optical mouse This section provides instructions on how to clean an optical mouse An optical mouse uses a light emitting diode LED and an optical sensor to navigate the pointer If the pointer on the screen does not move smoothly with the optical mouse you might need to clean the mouse To clean an optical mouse do the following 1 2 3 Turn off your computer Disconnect the mouse cable from the computer Turn the mouse upside down to check the lens a If there is a smudge on the lens gently clean the area with a plain cotton tipped swab b If there is debris in the lens gently blow the debris away from the area Check the surface on which you are using the mouse If you have a very intricate picture or pattern beneath the mouse it may be difficult for the digital signal processor DSP to determine changes in the mouse position Reconnect the mouse cable to the computer Turn your computer back on 50 ThinkCentre User Guide Chapter 7 Getting information help and service This chapter contains information about help service and technical assistance for products manufactured by Lenovo Information resources You can use the information in this section to access useful resources relating to your computing needs Online Books folder Note The Online Books folder is only available on computers that have an internal hard disk drive and preinstalled software fr
48. ice drivers e Solving recovery problems Notes 1 The recovery information in this chapter only applies to the computers that have a hard disk drive and preinstalled software from Lenovo 2 There are a variety of methods to choose from when considering how to recover in the event of a software or hardware related problem Some methods vary depending on the type of your operating system 3 The product on the recovery media may be used only for the following purposes e Restore the product preinstalled on your computer e Reinstall the product e Modify the product using the Additional Files Creating and using recovery media You can use recovery media to restore the hard disk drive to the factory default settings Recovery media are useful if you transfer the computer to another area sell the computer recycle the computer or put the computer in an operational state after all other methods of recovery have failed As a precautionary measure it is important to create recovery media as early as possible Note The recovery operations you can perform using recovery media vary depending on the operating system from which the recovery media were created The recovery media might contain a boot medium and a data medium Your Microsoft Windows license permits you to create only one data medium so it is important that you store the recovery media in a safe place after you have made them Creating recovery media This section provides instr
49. k with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 32 Replacing the battery Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support Your computer has a special type of memory that maintains the date time and settings for built in features such as parallel port assignments configuration A battery keeps this information active when you turn off the computer The battery normally requires no charging or maintenance throughout its life however no battery lasts forever If the battery fails the date time and configuration information including passwords are lost An error message is displayed when you turn on the computer Refer to the Lithium battery notice in the ThinkCentre Safety and Warranty Guide for information about replacing and disposing of the battery To replace the battery do the following 1 Turn off the computer and disconnect all power cords from electrical outlets 2 Open the computer cover See Opening the computer cover on page 12 3 Locate the battery See Locating parts on the system board on page 9 4 Remove the old battery
50. l drives 1 57 internal speaker replacing 28 K keyboard connector 8 keyboard replacing 31 L Lenovo ThinkVantage Toolbox 48 Lenovo ThinkVantage Tools 51 Lenovo Web site 52 Lenovo Welcome 5 52 locating components 8 media creating and using recovery media 35 memory module installing replacing 13 system board 13 Microphone connector 8 mouse connector 8 mouse replacing 31 N notice television output 56 notices 55 O online books folder 51 opening computer cover 12 operations backup and recovery 36 optical drive installing or replacing 20 optical mouse cleaning 50 P parts replacement completing 32 password Administrator 42 considerations 41 Power On Password 42 setting changing deleting 42 password protection 34 passwords erasing 34 lost or forgotten 34 passwords using 41 PC Doctor for Rescue and Recovery 49 PCI card 15 installing replacing 15 physical specifications 3 power Advanced Configuration and Power Interface ACPI support 2 features 2 58 ThinkCentre User Guide power supply assembly replacing 22 power on self test POST 45 Power On Password 42 productivity center ThinkVantage 51 programs updating system 45 protection password 34 purchasing additional services 54 R rear connectors 7 recovering from a POST BIOS update failure 46 software 35 recovery boot block 46 operations backup and 36 problems solving 40 recovery media creating and using 35
51. lenovo ThinkCentre User Guide ThinkGentre Machine Types 3026 3039 3137 3149 3245 3269 3319 3394 3491 3627 3699 3878 4972 5132 5261 5297 5391 5472 5485 5536 5548 5567 5864 and 6213 lenovo ThinkCentre User Guide Machine Types 3026 3039 3137 3149 3245 3269 3319 3394 3491 3627 3699 3878 4972 5132 5261 5297 5391 5472 5485 5536 5548 5567 5864 and 6213 Note Before using this information and the product it supports be sure to read and understand the ThinkCentre Safety and Warranty Guide and Appendix A Notices on page 55 First Edition October 2010 Copyright Lenovo 2010 LENOVO products data computer software and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C F R 2 101 with limited and restricted rights to use reproduction and disclosure LIMITED AND RESTRICTED RIGHTS NOTICE If products data computer software or services are delivered pursuant a General Services Administration GSA contract use reproduction or disclosure is subject to restrictions set forth in Contract No GS 35F 05925 Contents Important safety information Chapter 1 Product overview Features Specifications Software overview Software provided by enaus Adobe Reader Antivirus software Locations Locating connectors on iite frotit of your computer Locating conne
52. m programs This chapter provides information about updating the POST and BIOS and how to recover from a POST and BIOS update failure Using system programs System programs are the basic layer of software built into your computer System programs include the POST the BIOS and the Setup Utility program The POST is a set of tests and procedures that are performed each time you turn on your computer The BIOS is a layer of software that translates instructions from other layers of software into electrical signals that the computer hardware can execute You can use the Setup Utility program to view or change the configuration settings of your computer See Chapter 4 Using the Setup Utility on page 41 for detailed information Your computer system board has a module called electrically erasable programmable read only memory EEPROM also referred to as flash memory You can easily update the POST the BIOS and the Setup Utility program by starting your computer with a system program update disc or running a special update program from your operating system Lenovo might make changes and enhancements to the POST and BIOS When updates are released they are available as downloadable files on the Lenovo Web site at http Awww lenovo com Instructions for using the POST and BIOS updates are available in a TXT file that is included with the update files For most models you can download either an update program to create a system program updat
53. n internal hard disk drive a Windows 7 operating system and preinstalled software programs from Lenovo To access the Lenovo ThinkVantage Tools program click Start gt All Programs gt Lenovo ThinkVantage Tools ThinkVantage Productivity Center The ThinkVantage Productivity Center program contains information sources and tools designed to make computing easy and secure It provides easy access to various technologies such as e Client Security Solution e Power Manager e Productivity Center Copyright Lenovo 2010 51 e Product Recovery e Rescue and Recovery e System Update Note The ThinkVantage Productivity Center program is only available on computers that have an internal hard disk drive a preinstalled Windows Vista operating system and preinstalled software programs from Lenovo To access the ThinkVantage Productivity Center program click Start gt All Programs gt ThinkVantage gt Productivity Center Lenovo Welcome The Lenovo Welcome program introduces you to some innovative built in features of Lenovo and guides you through a few important setup tasks to help you make the most of your computer Note The Lenovo Welcome program is only available on computers that have an internal hard disk drive a preinstalled Windows 7 or Windows Vista operating system and preinstalled software programs from Lenovo Access Help The Access Help information system provides information about getting started doing basic t
54. necting 32 changing password 42 startup device sequence 43 cleaning an optical mouse 50 CMOS clearing 34 components accessing system board 12 components internal 8 computer cover opening 12 connector description 7 connectors front 6 rear 7 considerations passwords 41 creating and using a rescue medium 38 creating and using recovery media 35 CRU completing the installation 32 customer support center 53 D deleting a password 42 device drivers 33 installing 39 reinstalling 39 devices handling static sensitive 11 diagnostics programs using 53 diagnostics troubleshooting 47 DisplayPort connector 8 documentation using 53 drivers device 33 drives Copyright Lenovo 2010 bays 10 specifications 10 E environment operating 4 Ethernet 1 Ethernet connector 8 exiting Setup Utility 43 expansion 2 external options installing 11 F failure recovering from POST BIOS 46 features 1 flashing the BIOS 45 folder books online 51 front audio and USB assembly replacing 26 front connectors 6 G getting help 51 information 51 service 51 H hard disk drive replacing 18 heat sink replacing 24 help and service 53 getting 51 important safety information vii information getting 51 important safety vii resources 51 safety 52 warranty 52 Input Output I O features 2 installing device drivers 39 installing options memory module 13 PCI card 15 security features 33 interna
55. ntact your network or storage administrator To replace the hard disk drive do the following 1 Turn off the computer and disconnect all power cords from electrical outlets 2 Open the computer cover See Opening the computer cover on page 12 3 You might need to pivot the optical drive bay assembly upward to gain easier access to the hard disk drive See Accessing the system board components and drives on page 12 4 Locate the hard disk drive See Locating components on page 8 18 ThinkCentre User Guide 5 Push the release button J of the hard disk drive bracket as shown and then lift the hard disk drive bracket up from the heat sink Figure 15 Removing the hard disk drive 6 Disconnect the signal cable and the power cable from the hard disk drive to completely remove the hard disk drive from the chassis 7 Flex the sides of the bracket to remove the hard disk drive from the bracket 8 To install a new hard disk drive into the bracket flex the bracket and align pin pin i pin E and pin gy on the bracket with the corresponding holes in the hard disk drive Figure 16 Installing the hard disk drive into the bracket Important Do not touch the circuit board on the bottom of the hard disk drive 9 Connect the signal cable and the power cable to the new hard disk drive Chapter 2 Installing or replacing hardware 19 10 Insert the two retaining clips J of the hard disk dri
56. ole in the chassis 9 Install the screw to secure the new front audio and USB assembly to the chassis 26 ThinkCentre User Guide 10 Reconnect the front audio and USB assembly cables to the front audio connector and the front USB connector on the system board See Locating parts on the system board on page 9 What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 32 Replacing the system fan Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the system fan To replace the system fan do the following 1 Turn off the computer and disconnect all power cords from electrical outlets 2 Open the computer cover See Opening the computer cover on page 12 3 Remove the front bezel by releasing the three plastic tabs and pivoting the front bezel outward Figure 26 Removing the front bezel 4 Pivot the optical drive bay assembly upward See Accessing the system board components and drives on page 12 5 Locate the system fan See Locating components on pag
57. om Lenovo The Online Books folder preinstalled on your computer contains the ThinkCentre User Guide which provides information about your computer to help you set up use and maintain your computer It requires no Internet access to view the publication To view the publication click Start gt All Programs gt Online Books gt Online Books then double click the publication for your computer The publication is also available on the Lenovo Support Web site at http www lenovo com support Notes 1 The publication is in PDF version To view the publication you need to have the Adobe Reader program preinstalled on your computer If the Adobe Reader program has not been installed on your computer a message will be displayed when you attempt to view the PDF file and you will be guided through the Adobe Reader installation 2 The publication is available in other languages on the Lenovo Support Web site at http www lenovo com support 3 If you want to install a different language version of the Adobe Reader program rather than the version preinstalled on your computer download the desired language version from the Adobe Web site at http www adobe com Lenovo ThinkVantage Tools The Lenovo ThinkVantage Tools program guides you to a host of information sources and provides easy access to various tools to help you work more easily and securely Note The Lenovo ThinkVantage Tools program is only available on computers that have a
58. omputer ERB sae O O QOH 524040 D 2 sBepegege A EOT TREAT RRO 980802028 2 aanas OORO TOO R GS GQ 823002000 FOFO SRR SLAP SS L g O OI SSSR REESS S R arna 98888808888 ce ca fol OES RERERE RBS SBR QHOMES BEER EER O9 O ace O9 O 6 5 ICSI EA S9 Co see 5 20 Gol E Pa oe ji Ji HT Figure 2 Rear connector locations Optional serial port EJ VGA monitor connector not applicable on some models E Power cord connector EJ USB connectors 4 EJ Audio line in connector DisplayPort connector not applicable on some models E Audio line out connector USB connectors 2 E Microphone connector Ethernet connector E Serial port PCI Express x16 graphics card slot PS 2 keyboard and mouse connectors optional PCI card slot Connector Description Audio line in connector Used to receive audio signals from an external audio device such as a stereo system When you attach an external audio device a cable is connected between the audio line out connector of the device and the audio line in connector of the computer Audio line out connector Used to send audio signals from the computer to external devices such as powered stereo speakers speakers with built in amplifiers headphones multimedia k
59. omputer cover on page 12 Pivot the optical drive bay assembly upward to gain access to the power supply assembly See Accessing the system board components and drives on page 12 Disconnect the power supply assembly cables from all drives and from the power connectors fj and H on the system board Note You might need to remove the hard disk drive to gain easy access to the power connector H See Replacing the hard disk drive on page 18 o H o N ui a a Figure 22 Power connectors on the system board Chapter 2 Installing or replacing hardware 23 7 Release the power supply assembly cables from the cable clips and ties in the chassis 8 Slide the power supply assembly to the front of the computer and then lift it out of the chassis Figure 23 Removing the power supply assembly 9 Install the new power supply assembly into the chassis so that the screw holes in the new power supply assembly align with those in the chassis 10 Install and tighten the four screws to secure the power supply assembly Note Use only the scre
60. ons e Purchase upgrades and extended hardware repair services e Download the latest device drivers and software updates for your computer model e Access the online manuals for your products e Access the Lenovo Limited Warranty 52 ThinkCentre User Guide e Access troubleshooting and support information for your computer model and other supported products e Find the service and support phone numbers for your country or region e Find a Service Provider located near you Help and service This section contains information about obtaining help and service Using the documentation and diagnostic programs If you experience a problem with your computer see Chapter 6 Troubleshooting and diagnostics on page 47 For information on additional resources to help you troubleshoot your computer problem see Information resources on page 51 If you suspect a software problem see the documentation that comes with the operating system or software program including readme files and online help Most computers come with a set of diagnostic programs that help you identify hardware problems For instructions on using the diagnostic programs see Diagnostic programs on page 48 You can also get the latest technical information and download device drivers and updates from Lenovo Support Web site at http www lenovo com support Calling for service During the warranty period you can get help and information by telephone t
61. ost or forgotten password do the following 1 Remove all media from the drives and turn off all attached devices and the computer Then disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer 2 Open the computer cover See Opening the computer cover on page 12 3 Locate the Clear CMOS Recovery jumper on the system board See Locating parts on the system board on page 9 Move the jumper from the standard position pin 1 and pin 2 to the maintenance position pin 2 and pin 3 Close the computer cover and connect the power cord See Completing the parts replacement on page 32 Turn on the computer and leave it on for approximately 10 seconds Then turn off the computer by holding the power switch for approximately five seconds 7 Repeat step 1 through step 2 8 Move the Clear CMOS Recovery jumper back to the standard position pin 1 and pin 2 9 Close the computer cover and connect the power cord See Completing the parts replacement on page 32 34 ThinkCentre User Guide Chapter 3 Recovery information This chapter provides information about the recovery solutions provided by Lenovo This chapter contains the following topics e Creating and using recovery media e Performing backup and recovery operations e Using the Rescue and Recovery workspace e Creating and using a rescue medium e Installing or reinstalling dev
62. ot device window displays release the F12 key 3 Select the desired startup device and press Enter The computer will start up from the device you selected Note Selecting a startup device from the Please select boot device window does not permanently change the startup sequence Selecting or changing the startup device sequence To view or permanently change the configured startup device sequence do the following 1 Start the Setup Utility program See Starting the Setup Utility program on page 41 2 From the Setup Utility program main menu select Startup 3 Select the devices for the Primary Startup Sequence the Automatic Startup Sequence and the Error Startup Sequence Read the information displayed on the right side of the screen 4 Press F10 to save and exit the Setup Utility program See Exiting from the Setup Utility program on page 43 Exiting from the Setup Utility program After you finish viewing or changing settings press Esc to return to the Setup Utility program main menu You might have to press Esc several times Do one of the following e If you want to save the new settings press F10 to save and exit the Setup Utility program e If you do not want to save the settings select Exit gt Discard Changes and Exit e If you want to return to the default settings press F9 to load the default settings Chapter 4 Using the Setup Utility 43 44 ThinkCentre User Guide Chapter 5 Updating syste
63. r To open the computer cover see Opening the computer cover on page 12 Figure 3 Component locations 8 ThinkCentre User Guide E Hard disk drive installed in some models H Heat sink Ef Internal speaker installed in some models E System fan assembly H Optical drive Gi Memory module Power supply assembly Locating parts on the system board Figure 4 System board part locations on page 9 shows the locations of the parts on the system board x a8 6 a jaits N j By 5 Ot zoze mta n T Figure 4 System board part locations EJ PC card slot HJ PC Express x16 graphics card slot EJ Internal speaker connector E Cover presence switch connector Intrusion switch connector H Battery i Thermal sensor connector Microprocessor fan connector EJ Microprocessor EJ 4 pin power connector EQ Memory slot 2 Memory slot 1 EEA Memory slot 4 EER Memory slot 3 EJ Front panel connector EH PS 2 keyboard and mouse connector EG Serial COM connector Front audio connector EEJ 24 pin po
64. routed correctly Keep cables clear of the hinges and sides of the computer chassis to avoid interference with closing the computer cover 32 ThinkCentre User Guide Tar iu Figure 32 Cable routing Lower the optical drive bay assembly Close the computer cover If there is an integrated cable lock available lock the computer pol OD OL oP Reconnect the external cables and power cords to the computer See Locating connectors on the rear of your computer on page 7 8 To update your configuration see Chapter 4 Using the Setup Utility on page 41 Note In most areas of the world Lenovo requires the return of the defective Customer Replaceable Unit CRU Information about this will come with the CRU or will come a few days after the CRU arrives Obtaining device drivers You can obtain device drivers for operating systems that are not preinstalled at http www lenovo com support Installation instructions are provided in readme files with the device driver files Installing security features There are several security options available to help you prevent hardware theft and unauthorized access to your computer In addition to physical locks you can
65. rs preinstalled with the Windows 7 operating system from Lenovo Power Manager The Power Manager program provides convenient flexible and complete power management for your ThinkCentre computer By using the Power Manager program you can adjust your power settings to achieve the best balance between system performance and power saving Product Recovery The Product Recovery program enables you to restore the contents of the hard disk drive to the factory default settings Fingerprint Software The integrated fingerprint reader provided on some keyboards enables you to enroll your fingerprint and associate it with your power on password hard disk drive password and Windows password As a result fingerprint authentication can replace passwords and enable simple and secure user access A fingerprint reader keyboard is available with select computers or can be purchased for computers that support this option Chapter 1 Product overview 5 Lenovo ThinkVantage Toolbox The Lenovo ThinkVantage Toolbox program helps you maintain your computer improve computing security diagnose computer problems get familiar with the innovative technologies provided by Lenovo and get more information about your computer See Lenovo ThinkVantage Toolbox on page 48 for detailed information PC Doctor for Rescue and Recovery The PC Doctor for Rescue and Recovery diagnostic program is preinstalled on your hard disk drive It is part of the Rescue
66. s Ef that secure the heat sink to the system board Note Carefully remove the four screws from the system board to avoid any possible damage to the system board The four screws cannot be removed from the heat sink a o Figure 24 Removing the heat sink Carefully lift the heat sink off the system board Notes a You might have to gently twist the heat sink to free it from the microprocessor b Do not touch the thermal grease while handling the heat sink Position the new heat sink on the system board so that the four screws are aligned with the holes on the system board Alternate tightening each screw a small and equal amount until the heat sink is secured to the system board Do not over tighten the screws What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 32 Chapter 2 Installing or replacing hardware 25 Replacing the front
67. s the user s responsibility to evaluate and verify the operation of any other product program or service Lenovo may have patents or pending patent applications covering subject matter described in this document The furnishing of this document does not give you any license to these patents You can send license inquiries in writing to Lenovo United States Inc 1009 Think Place Building One Morrisville NC 27560 U S A Attention Lenovo Director of Licensing LENOVO PROVIDES THIS PUBLICATION AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions therefore this statement may not apply to you This information could include technical inaccuracies or typographical errors Changes are periodically made to the information herein these changes will be incorporated in new editions of the publication Lenovo may make improvements and or changes in the product s and or the program s described in this publication at any time without notice The products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons The information contained in this document does not affect or change Lenovo product speci
68. talling or reinstalling device drivers Solving recovery problems Chapter 4 Using the Setup e Starting the Setup Utility program Viewing and changing settings Using passwords Password considerations Power On Password Administrator Password Hard Disk Password Seu a 4 Setting changing and deleting a password Enabling or disabling a device Selecting a startup device D Rys Selecting a temporary startup device Selecting or eae the eee device sequence Exiting from the Setup Utility program Chapter 5 alae ee programs Using system programs Updating flashing the BIOS fein a dist Updating eee the BIOS from your none system Recovering from a POST BIOS ipdate failure Chapter 6 POR ee and diagnostics Basic troubleshooting Diagnostic programs 5 Lenovo ThinkVantage Toolbox PC Doctor for Rescue and Recovery PC Doctor for DOS Cleaning an optical mouse Chapter 7 Getting information n and service Information resources 36 36 36 37 37 38 38 39 39 40 41 41 41 41 41 42 42 42 42 42 43 43 43 43 45 45 45 46 46 47 47 48 48 49 49 50 51 51 Online Books folder Lenovo ThinkVantage Tools ThinkVantage Productivity Center Lenovo Welcome Access Help vas ike ok Safety and Warranty Lenovo Web site http www lenovo com Help and service vi Using the documentation and diagnostic programs ThinkCen
69. ter cover and reconnect the power cords for the computer and monitor to electrical outlets See Completing the parts replacement on page 32 15 Turn on the computer to restart the operating system 46 ThinkCentre User Guide Chapter 6 Troubleshooting and diagnostics This chapter describes some basic troubleshooting and diagnostic programs If your computer problem is not described here see Chapter 7 Getting information help and service on page 51 for additional troubleshooting resources Basic troubleshooting The following table provides information to help you troubleshoot your computer problems Note If you cannot correct the problem have the computer serviced For a list of service and support telephone numbers refer to the ThinkCentre Safety and Warranty Guide that comes with your computer or go to the Lenovo Support Web site at http Awww lenovo com support phone a T The computer does not start Verify that when you press the power Switch e The power cord is correctly connected to the rear of the computer and to a working electrical outlet If your computer has a secondary power switch on the rear of the computer make sure that it is switched on The power indicator on the front of the computer is on The computer voltage matches the voltage available at the electrical outlet for your country or region The monitor screen is blank Verify that e The monitor signal cable is correctly conn
70. to a host of information and tools to help you set up understand maintain and enhance your computer Note The ThinkVantage Productivity Center program is only available on computers preinstalled with the Windows Vista operating system from Lenovo Lenovo Welcome The Lenovo Welcome program introduces you to some innovative built in features of Lenovo and guides you through a few important setup tasks to help you make the most of your computer ThinkVantage Rescue and Recovery The ThinkVantage Rescue and Recovery program is a one button recovery and restore solution that includes a set of self recovery tools to help users diagnose computer problems get help and recover from system crashes quickly even if the primary operating system will not start ThinkVantage Client Security Solution The ThinkVantage Client Security Solution program is available on select Lenovo computers It helps protect your information including vital security information like passwords encryption keys and electronic credentials while guarding against unauthorized user access to data Note The ThinkVantage Client Security Solution program is only available on computers preinstalled with the Windows Vista operating system from Lenovo Password Manager The Password Manager program helps you automatically capture and fill in authentication information for Windows applications and Web sites Note The Password Manager program is only available on compute
71. to the USB connector cannot be used SATA Controller When this feature is set to Disable all devices connected to the SATA connectors such as hard disk drives or the optical drive are disabled and cannot be accessed External SATA Port When this option is set to Disable the device connected to the External SATA connector cannot be accessed To enable or disable a device do the following 1 Start the Setup Utility program See Starting the Setup Utility program on page 41 42 ThinkCentre User Guide 2 From the Setup Utility program main menu select Devices 3 Depending on the device you want to enable or disable do one of the following e Select USB Setup to enable or disable a USB device e Select ATA Drive Setup to enable or disable an internal or external SATA device 4 Select the desired settings and press Enter 5 Press F10 to save and exit the Setup Utility program See Exiting from the Setup Utility program on page 43 Selecting a startup device If your computer does not start up from a device such as the disc diskette or hard disk drive as expected do one of the following to select the startup device you want Selecting a temporary startup device Use this procedure to select a temporary startup device Note Not all discs hard disk drives and diskettes are bootable 1 Turn off your computer 2 Repeatedly press and release the F12 key when turning on the computer When the Please select bo
72. tre User Guide 51 51 51 52 52 52 52 53 53 Calling for service Using other services Purchasing additional services Appendix A Notices Television output notice European conformance CE mark Trademarks Index 53 54 54 55 56 56 56 57 Important safety information CAUTION Before using this manual be sure to read and understand all the related safety information for this product Refer to the ThinkCentre Safety and Warranty Guide that you received with this product for the latest safety information Reading and understanding this safety information reduces the risk of personal injury and or damage to your product If you no longer have a copy of the ThinkCentre Safety and Warranty Guide you can obtain a Portable Document Format PDF version from the Lenovo Support Web site at http www lenovo com support Copyright Lenovo 2010 vii viii ThinkCentre User Guide Chapter 1 Product overview This chapter describes the computer features specifications preinstalled software programs and part and connector locations Features This section provides information about the computer features System information The following information covers a variety of models For information about your specific model use the Setup Utility program See Chapter 4 Using the Setup Utility on page 41 Microprocessor Your computer comes with one of the following microprocessors internal cach
73. tries where service is available go to http www lenovo com support click Warranty and follow the instructions on the screen For technical assistance with the installation of or questions related to Service Packs for your preinstalled Microsoft Windows product refer to the Microsoft Product Support Services Web site at http support microsoft com directory or you can contact the Customer Support Center Some fees might apply Purchasing additional services During and after the warranty period you can purchase additional services such as support for hardware operating systems and application programs network setup and configuration upgraded or extended hardware repair services and custom installations Service availability and service name might vary by country or region For more information about these services go to the Lenovo Web site at http www lenovo com 54 ThinkCentre User Guide Appendix A Notices Lenovo may not offer the products services or features discussed in this document in all countries Consult your local Lenovo representative for information on the products and services currently available in your area Any reference to a Lenovo product program or service is not intended to state or imply that only that Lenovo product program or service may be used Any functionally equivalent product program or service that does not infringe any Lenovo intellectual property right may be used instead However it i
74. tup Utility The Setup Utility program is used to view and change the configuration settings of your computer regardless of which operating system you are using However the operating system settings might override any similar settings in the Setup Utility program Starting the Setup Utility program To start the Setup Utility program do the following 1 Make sure your computer is turned off 2 Repeatedly press and release the F1 key when turning on the computer When you hear multiple beeps or see a logo screen release the F1 key Note If a Power On Password or an Administrator Password has been set the Setup Utility program menu will not be displayed until you type the correct password For more information see Using passwords on page 41 The Setup Utility program might start automatically when POST detects that hardware has been removed or new hardware has been installed in your computer Viewing and changing settings The Setup Utility program menu lists various items about the system configuration To view or change settings start the Setup Utility program See Starting the Setup Utility program on page 41 Then follow the instructions on the screen When working with the Setup Utility program menu you must use the keyboard The keys used to perform various tasks are displayed at the bottom of each screen Using passwords By using the Setup Utility program you can set passwords to prevent unauthori
75. uctions on how to create recovery media on different operating systems Note On the Windows 7 operating system you can create recovery media using discs or external USB storage devices On the Windows Vista operating systems you can create recovery media using only discs so this operation is also called creating Product Recovery discs e To create recovery media on the Windows 7 operating system click Start gt All Programs gt Lenovo ThinkVantage Tools gt Factory Recovery Disks Then follow the instructions on the screen e To create Product Recovery discs on the Windows Vista operating system click Start gt All Programs gt ThinkVantage gt Create Product Recovery Media Then follow the instructions on the screen Copyright Lenovo 2010 35 Using recovery media This section provides instructions on how to use recovery media on different operating systems On the Windows 7 operating system and the Windows Vista operating system you can use recovery media to restore the computer to the factory default settings only You can use recovery media to put the computer in an operational state after all other methods of recovery have failed Attention When you use recovery media to restore the computer to the factory default settings all the files currently on the hard disk drive will be deleted and replaced by the factory default settings To use recovery media on the Windows 7 operating system or the Windows Vista operatin
76. understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support Notes 1 Use only computer parts provided by Lenovo 2 When installing or replacing an option use the appropriate instructions in this section along with the instructions that come with the option Installing external options You can connect external options to your computer such as external speakers a printer or a scanner For some external options you must install additional software in addition to making the physical connection When installing an external option see Locating connectors on the front of your computer on page 6 and Locating connectors on the rear of your computer on page 7 to identify the required connector Then use the instructions that come with the option to help you make the connection and install any software or device drivers that are required for the option Copyright Lenovo 2010 11 Opening the computer cover Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to op
77. ve bracket into the corresponding holes in the chassis and then pivot the hard disk drive and bracket downwards until the hard disk drive bracket snaps into position Figure 17 Installing the hard disk drive 11 Go to Completing the parts replacement on page 32 Replacing the optical drive Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the optical drive To replace the optical drive do the following 1 Turn off the computer and disconnect all power cords from electrical outlets 2 Open the computer cover See Opening the computer cover on page 12 3 Pivot the optical drive bay assembly upward to gain easy access to the optical drive See Accessing the system board components and drives on page 12 4 Disconnect the signal cable and the power cable from the rear of the optical drive 5 Press the optical drive lock fj and slide the optical drive out of the rear of the drive bay assembly 20 ThinkCentre User Guide Figure 18 Removing the old optical drive Install the optical drive retainer on the side of the new optical drive B
78. wer connector EER Power fan connector EJ SATA connectors 2 eSATA connector EA Front USB connectors 2 EE Clear CMOS Complementary Metal Oxide Semiconductor Recovery jumper Chapter 1 Product overview 9 Locating internal drives Internal drives are devices that your computer uses to read and store data You can add drives to your computer to increase storage capacity and enable your computer to read other types of media Your computer comes with the following factory installed drives e A3 5 inch hard disk drive in bay 1 installed in some models e An optical drive in bay 2 Internal drives are installed in bays In this manual the bays are referred to as bay 1 bay 2 and so on Figure 5 Drive bay locations on page 10 shows the locations of the drive bays Figure 5 Drive bay locations The following list describes the type and size of the drive that you can install in each bay Bay 1 Maximum height 26 1 mm 1 03 inches 3 5 inch hard disk drive E Bay 2 Maximum height 41 6 mm 1 64 inches Optical drive 10 ThinkCentre User Guide Chapter 2 Installing or replacing hardware This chapter provides instructions on how to install or replace hardware for your computer Handling static sensitive devices Do not open the static protective package containing the new part until the defective part has been removed from the computer and you are ready to install the new part Static electricity
79. ws provided by Lenovo 11 Reconnect all the power supply assembly cables to the system board and each of the drives 12 Secure the power supply assembly cables with the cable clips and ties in the chassis What to do next e To work with another piece of hardware go to the appropriate section e To complete the installation or replacement go to Completing the parts replacement on page 32 Replacing the heat sink Attention Do not open your computer or attempt any repair before reading and understanding the Important safety information in the ThinkCentre Safety and Warranty Guide that came with your computer To obtain a copy of the ThinkCentre Safety and Warranty Guide go to http www lenovo com support This section provides instructions on how to replace the heat sink 24 ThinkCentre User Guide CAUTION A The heat sink might be very hot Turn off the computer and wait three to five minutes to let the computer cool before opening the computer cover To replace the heat sink do the following 1 2 3 8 Turn off the computer and disconnect all power cords from electrical outlets Open the computer cover See Opening the computer cover on page 12 Pivot the optical drive bay assembly upward See Accessing the system board components and drives on page 12 Remove the hard disk drive to access the heat sink See Replacing the hard disk drive on page 18 Carefully remove the four screw
80. zed access to your computer and data The following types of passwords are available e Power On Password e Administrator Password e Hard Disk Password You do not have to set any passwords to use your computer However using passwords improves computing security If you decide to set any passwords read the following sections Password considerations A password can be any combination of up to 64 alphabetic and numeric characters For security reasons it is recommended to use a strong password that cannot be easily compromised To set a strong password use the following guidelines e Have at least eight characters in length e Contain at least one alphabetic character and one numeric character e Setup Utility program and hard disk drive passwords are not case sensitive Copyright Lenovo 2010 41 e Not be your name or your user name e Not be a common word or a common name e Be significantly different from your previous passwords Power On Password When a Power On Password is set you are prompted to type a valid password each time the computer is turned on The computer cannot be used until the valid password is typed in Administrator Password Setting an Administrator Password deters unauthorized users from changing configuration settings If you are responsible for maintaining the configuration settings of several computers you might want to set an Administrator Password When an Administrator Password is set you are prompt

Lenovo ThinkCentre M90

Contents

Download Pdf Manuals

Related Search

Related Contents