Chief JHSUB flat panel ceiling mount
Contents
1. INSTRUCTIONS INSTALLATION Direct Attach Ceiling Mount JHS SERIES a CHIEF ISION Our Mounts Your V JHS SERIES DISCLAIMER Milestone AV Technologies Inc and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief and Centris are registered trademarks of Milestone AV Technologies Inc All rights reserved IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions DIMENSIONS 1 1 2 N MEASUREMENTS IN MILLIMETERS INCHES 91 1 C LOF VESA PATTERN Installation Instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to rea2. d thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity of the mount can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of the mount and all attached components does not exceed 75lbs 34 02kg UP DOWN TILT 15 LEFT RIGHT SWIVEL 75 128 3 5 05 i Installation Instructions JHS SERIES LEGEND Tighten Fastener Phillips Screwdriver amp Loosen Fastener Hex Head Wrench Chave de cabe a sextavada TOOLS REQUIRED FOR INSTALLATION AND PARTS 3 16 provided 5 32 provided D B 2 5 16 18 x 3 8 Interface Bracket Kit including hardware JHS SERIES INSTALLATION Mount Installation IMPORTANT The following installation instructions assume that a 1 1 2 NPT pipe has been properly in
3. l two more of the same screws through lower mounting holes in Centris cup and into display back See Figure 4 Tighten all hardware Route cables and wires to display Figure 5 Figure 4 JHS SERIES Installation Instructions Installation Instructions JHS SERIES JHS SERIES a CHIEF Our Mounts Your Vision Chief Manufacturing a division of Milestone AV Technologies 8805 000220 Rev A 2008 Milestone AV Technologies www chiefmfg com 06 08 Installation Instructions USA International A 8401 Eagle Creek Parkway Savage MN 55378 P 800 582 6480 952 894 6280 F 877 894 6918 952 894 6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN The Netherlands P 31 0 40 2668620 F 31 0 40 2668615 A Room 24F Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA AA n 6A Y ER BB En XIE DIR 24F P 86 755 8996 9226 F 86 755 8996 9217 PN Asia Pacific tag consumer
4. lation instructions WARNING IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Using screws of improper size may damage your display Proper screws will easily and completely thread into display mounting holes Ensure that screws are not too long WARNING IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Inadequate thread engagement in display may cause display to fall Back out screws ONLY as necessary to allow installation of Centris cup Start two M4 x 8mm Phillips pan head screws included in hardware kit into upper mounting holes in display back See Figure 3 NOTE Leave at least 1 8 of each screw protruding out back of display Installation Instructions JHS SERIES Adjustments To adjust display Roll Pitch and YAW tension Disconnect all wires and cable from the display Remove two Lower screws securing display to Centris cup Loosen two Upper screws securing display Lift display upward and away from mount Using a hex head wrench turn the tension adjustment screw clockwise to increase tension or counter clockwise to decrease tension See Figure 5 6 Re install display pr a NS Figure 3 2 Align two screws in display back with upper mounting holes in Centris cup and lower display until screws are seated in lower area of teardrop mounting holes See Figure 4 3 Instal
5. stalled and is in place 1 Thread mount A onto 1 1 2 NPT pipe until hand tight 2 Adjust mount A position until Centris cup is facing the desired position of the display See Figure 1 1 1 2 NPT Pipe Centris Cup Figure 1 3 When mount A is properly positioned secure mount A to 1 1 2 NPT pipe by installing and tightening 5 16 18 x 3 8 set screw B using 3 16 hex wrench See Figure 2 NOTE If mountis being used to couple two pipes use both set screws when securing mount A to pipes Figure 2 NOTE 1 Installation Instructions Display Installation 1 Determine mounting pattern on display WARNING IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT DO NOT substitute hardware Use only hardware supplied by manufacturer WARNING IMPROPER INSTALLATION CAN LEAD TO ELECTRIC SHOCK OR DAMAGE TO EQUIPMENT Screw length must not exceed the depth of threaded mounting insert in display WARNING OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE TO EQUIPMENT DO NOT over tighten screws when installing interface bracket NOTE If the display being installed has a 100x100 VESA mounting pattern no interface bracket is required and the display can be mounted directly to the Centris cup as outlined below If the display being installed requires an interface bracket refer to the interface bracket instal
Download Pdf Manuals
Related Search