Miele DA 5495 W
Contents
1. gt For safety reasons this appliance may only be used when it has been fully installed gt Only open the housing as described in the instructions given in the installation sheet and in the Cleaning and care section of this booklet Under no circumstances should any other parts of the housing be opened Tampering with electrical connections or components and mechanical parts is highly dangerous to the user and can cause operational faults gt Installation maintenance and repairs may only be carried out by a Miele authorised person in strict accordance with current national and local safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work Ensure that current is not supplied to the appliance until after maintenance or repair work has been carried out gt Faulty components must only be replaced by genuine Miele original parts The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used gt During installation maintenance and repair work the appliance must be disconnected from the mains electricity supply It is only completely isolated from the electricity supply when itis switched off at the isolator or the screw out fuse is removed in countries where this is applicable or the mains fuse is disconnected or it is switched off at the wall socket an2. 270 459 520 290 630 898 A Tan dai2689 The diagram is not drawn to scale 20 Appliance dimensions Extraction Recirculation Ventilation grille positioned at the top for recirculation is not required for recirculation mode cooker hoods The shaded area represents the wall or ceiling area for the vent cut out for fitting the connection socket and on EXT models for feeding the connection cable through to the external motor For recirculation mode only a connection socket needs to be fitted Connection for air extraction 150 mm or 125 mm with reducing collar Safety distance between hob and cooker hood S When planning the installation height of your cooker hood the minimum safety distances between the top of a cooker or hob and the bottom of the cooker hood are as follows unless a greater distance is specified by the manufacturer of your cooking appliance 450 mm GB 600 mm AU NZ above electric hobs and cookers 650 mm above an open grill or deep fat fryer 650 mm above gas hobs and cookers If this cooker hood is installed above a Miele Wok CS 1028 CombiSet appliance a minimum safety distance of 760 mm must be maintained between the burner and the lower edge of the cooker hood See Warning and Safety instructions for further information When deciding on the safety distance between the hob a
3. switch on the cooker hood lighting via a light switch in the house Installation jel dai1691e The tower needs to be removed before the control module can be fitted to the motor unit The control module is supplied with its own detailed operating and installation instructions 31 After Sales Service In the event of a fault which you cannot correct yourself or if the appliance is under guarantee please contact Your Miele Dealer Chartered Agent or The Miele Service Department see back cover for address When contacting your Dealer or Miele please quote the model and serial number of your appliance These are shown on the data plate which is visible when the grease filter is removed For G B Please note that telephone calls may be monitored and recorded for training purposes N B A call out charge will be applied for service visits where the problem could have been resolved as described in these instructions 32 Technical data Total connected load 160 W Fan motor 120W Hob lighting 2x20W Voltage ssi pipi AC 230 V FIEQUCNGY oi inn ek a 50 Hz FUSE TAUAG sini dead a win toe Rw aes 5A Electrical cable length 1 5m Weight DA 5495 Wi 26 kg DA 5495 W EXT LL 23 kg Fan performance Extraction power according to EN 61591 Extraction system 150 mm Keveldi grana ei 150 m h LOVEl 2
4. After cleaning leave the filters to dry on an absorbent surface before replacing them m When removing the filters for cleaning also clean off any residues of oil or fat from the now accessible housing to prevent the risk of these catching fire When putting the grease filters back in position ensure that the locking clips are facing down towards the hob dai1619 m f a grease filter is inadvertently replaced upside down insert a small screwdriver blade into the slit to disengage the clip Cleaning and care Fitting and replacing the charcoal filter If the cooker hood is connected for recirculation a charcoal filter must be inserted in addition to the grease filters This is designed to absorb cooking odours It is fitted in the canopy above the grease filters New charcoal filters can be purchased from your Miele dealer from the Miele Spare Parts Department or via the internet at www miele shop com See back cover for contact details and Technical data for the model number of the filter m Before fitting or replacing a charcoal filter the grease filters must first be taken out see previous section for instructions on how to do this m Take the charcoal filter out of its packaging dai2193 m Insert the charcoal filter into the back ofthe charcoal filter frame then push up into the frame at the front m Replace the g
5. cucina 250 m h Level 3 350 m h IS Intensive setting 500 m h Extraction system 125 mm Levele ces haces ea 130 m h Level Z u ner 230 m h Level3 0 0 0 cee eee 330 m h Intensive setting 450 m h Recirculation with charcoal filter LEVelllc ciare 100 m8 h Level2o ui rast 150 m h Level 3 250 m h Intensive setting 350 m h Optional extras for recirculation mode Conversion Kit DUW 20 Miele charcoal filter DKF 12 1 For EXT models the connected load and extraction power will depend on the type of external motor fitted EXT models Length of connection cable to external MOSER ee 1 9m 33 34 35 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW Tel 0845 365 0555 Fax 0845 365 0777 Customer Contact Centre Tel 0845 365 6600 E mail info miele co uk Internet www miele co uk Australia Miele Australia Pty Ltd ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 03 9764 7130 Fax 03 9764 7149 Internet www miele com au China Miele Shanghai Suite 4105 06 Plaza 66 1266 Nanjing Road West Jing An District Shanghai 200040 PRC Tel 86 21 6288 4200 Fax 86 21 6288 4100 E mail mieleshanghai cn miele com Internet www miele cn Miele Hong Kong Limited 41 F 4101 Manhattan Place 23 Wang Tai Road Kowloon Bay Hong Kong Tel 852 2610 1331 Fax 852 2610 1013 Email mielehk mi
6. for the On Off sensor on the cooker hood will flash The cooker hood lighting is not affected by this EXT models can also be connected to a window contact switch Take care when ventilating the room through an open window that ventilation is not impaired by a closed blind or curtain 30 If the control module is disconnected in order to operate the cooker hood without the window contact switch e g after moving house the cooker hood electronics must be reset by a Miele service technician Potential free connection This enables a further appliance to be controlled by the switch setting on the cooker hood fan For instance it can be used to ensure a sufficient supply of fresh air when the cooker hood and a heating appliance which also depends on the air in the room are being used together by switching on an air intake fan or opening a motorised inlet flap as soon as the cooker hood fan is switched on It is important to ensure that the fan power is sufficient and that the air intake has a suitable cross sectional area If a sufficient air intake cannot be guaranteed then the potential free contact will enable a heating appliance which depends on air in the same room as a cooker hood to be switched off when the cooker hood is in operation See also Warning and Safety instructions Operation with Control module DSM 400 Connection to a light switch The control module can be used to
7. heaters continuous flow or other water heaters gas hobs cookers or ovens which draw air in from the room and duct exhaust gases out through a chimney or extraction ducting When used in extraction mode with or without an external motor fitted the appliance draws air in from the room in which it is installed and from neighbouring rooms If there is insufficient air an underpressure will occur The heating appliance may be starved of oxygen impairing combustion Harmful gases could be drawn out of the chimney or extraction ducting back into the room with potentially fatal consequences Warning and safety instructions In order to ensure safe operation and to prevent gases given off by the heating appliances from being drawn back into the room when the cooker hood and the heater are in operation simultaneously an underpressure in the room of 0 04 mbar 4 pa is the maximum permissible dai1477 Ventilation can be maintained by air inlets which cannot be blocked in windows doors and outside wall vents One of the following technical measures may be necessary to ensure safe operation If the only way of ensuring adequate ventilation is via an open window a window contact switch should be fitted to ensure that the cooker hood can only operate when the window is opened sufficiently A window contact switch kit is available fro
8. the kitchen gt Older children may use the cooker hood only when its operation has been clearly explained to them and they are able to use it safely recognising the dangers of misuse gt Please be aware that on cooker hoods with halogen lighting the lamps will get very hot during use and remain hot for some time after switching off To safeguard against burning keep children well away from the lamps at all times Warning and safety instructions Technical safety gt Before installation check the cooker hood for visible signs of damage Under no circumstances should you install or use a damaged appliance It could be dangerous gt Before connecting the appliance to the mains supply make sure that the voltage and frequency details given on the data plate correspond with the on site electricity supply otherwise the appliance could be damaged Consult a qualified electrician if in any doubt gt The electrical safety of this appliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system which complies with current local and national safety regulations It is most important that this basic safety requirement is present and tested regularly and where there is any doubt the household wiring system should be inspected by a qualified electrician The manufacturer cannot be held liable for the consequences of an inadequate earthing system e g electric shock
9. Miele Operating and installation instructions Cooker hood DA 5495 W DA 5495 W EXT To avoid the risk of accidents en GB or damage to this appliance it is essential to read these instructions before it is installed and used for the first time M Nr 07 816 640 Contents Caring for the environment 0000 c cee ee 3 Warning and safety instructions 4 Guide to the appliance 0 00 0 cee 10 Modes of operation 1 0 0 0 0 ee 12 Operation resse piges ra A ware deh A br AA Aa 13 To switch the fan on 13 To select a power level 4 0 13 IO BIQMUHMG Per nis ak apie Pa hee ewe ah Se eae dee ee Aegean a 14 Cleaning and care tees 15 O O eea a a aa E a E ES e e E A na 15 Grease tillers 4 3 20 0 24 An ee een EE a a 16 Fitting and replacing the charcoal filter 18 Changing a halogen lamp 19 Appliance dimensions 20 Safety distance between hob and cooker hood S 00 eee 21 Installation n 22 2 eae AE REA AE 23 Installation instructions sser acert reg ee 23 Procive Dili Gnade 2 einer aan 23 DISMANUING 224034440444 ire bad ik 23 Assembly Balls a 0 0004 LE hea et eae dhe 24 Connection for air extraction 0 26 Condensate TAD i s24 bea Ped oad MeN aber edna baa ek RPE OPES ai 27 SENCO sce oe oe aoa ad Yee ey Shee Pew era 28 Electrical connection 29 Operation with Control module DSM 400 30 Connection to a window contact
10. afety installation use and maintenance of the appliance Keep these instructions in a safe place and ensure that all users are familiar with the contents Pass them on to any future owner of the appliance Correct application gt This appliance is not designed for commercial use It is intended for use in domestic households and for use in similar working and residential environments such as Shops Offices and showrooms and by residents in establishments such as Hostels and guesthouses gt It must only be used as a domestic appliance to extract vapours and remove odours from cooking Any other usage is not supported by the manufacturer and could be dangerous Miele cannot be held liable for damage resulting from incorrect or improper use or operation of the appliance gt This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience or knowledge unless they are supervised whilst using it or have been shown how to use it by a person responsible for their safety Safety with children gt This appliance is only intended for use by adults who have read these instructions It is not a toy To avoid the risk of injury keep children well away and do not allow them to play with it or use the controls They will not understand the potential dangers posed by it They should be supervised whenever you are working in
11. coal filter see Technical Data RR The air is drawn in and cleaned first by the grease filters and then by a charcoal filter The cleaned air is then recirculated back into the kitchen through grilles in the top of the cooker hood telescopic extension piece Before using the cooker hood in recirculation mode ensure that the charcoal filter is in place See Cleaning and care an external motor EXT models only URI The EXT models are designed to be connected to an external motor located outside the room The external motor is connected to the cooker hood by means of a control cable and is operated by the controls on the cooker hood Operation To switch the fan on m Press the On Off control The fan will come on at power level Il If the cooker hood has been connected to a window contact switch via the Miele DSM 400 control module then the fan cannot be switched on if the window is shut The symbol flashes To select a power level m To select a lower power level press the symbol or to select a higher power level press the symbol Depending on the intensity of the cooking vapours levels I to III are usually sufficient for normal cooking Intensive setting For short periods of cooking food with intensive vapours and a strong aroma e g when searing meat you may wish to select the Intensive Setting IV Automatic switch off of the Intensi
12. d the plug withdrawn or the fuse from the fused spur connection until is withdrawn Warning and safety instructions gt Do not connect the appliance to the mains electricity supply by a multi socket unit or an extension lead These do not guarantee the required safety of the appliance e g danger of overheating gt For appliances with an external fan motor fitted EXT models the connection of the two units must be made using the connection cable and the plug connectors These models may only be combined with a Miele external motor gt This appliance may only be used in mobile installations if a risk assessment of the installation has been carried out by a suitably qualified engineer gt In areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the appliance and its surroundings in a clean condition at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee Using at the same time as other heating appliances that depend on the air from the room Warning danger of toxic fumes Aa 7TSS 0000 dai1474 gt Great care should be taken when using the cooker hood at the same time and in the same room or area of the house as another heating appliance which depends on the air in the room Such appliances include gas oil wood or coal fired boilers and
13. ele com hk India Miele Appliances India Pvt Ltd Ground Floor Copia Corporate Suites Plot No 9 Jasola New Delhi 110025 Tel 011 46 900 000 Fax 011 46 900 001 E mail customercare miele in Internet www miele in Germany Miele amp Cie KG Carl Miele StraBe 29 33332 G tersloh Ireland Miele Ireland Ltd Broomhill Road Tallaght Dublin 24 Tel 01 461 0710 Fax 01 461 07 97 E Mail info miele ie Internet www miele ie New Zealand Miele New Zealand Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland NZ Tel 0800 264 353 Fax 0800 463 453 Internet www miele co nz Singapore Miele Southeast Asia Miele Pte Ltd 163 Penang Road 04 02 03 Winsland House Il Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail infosea miele com sg nternet www miele sg South Africa Miele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 27 0 11 548 1900 Fax 27 0 11 548 1935 E mail info miele co za nternet www miele co za United Arab Emirates Miele Appliances Ltd P O Box 11 47 82 Gold amp Diamond Park Sheikh Zayed Road Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 971 4 341 88 52 E Mail info miele ae Internet www miele ae Alteration rights reserved 0410 CE M Nr 07 816 640 00
14. esult in the exhaust ducting distorting To achieve the greatest possible air extraction with the lowest noise level please note the following To ensure efficient air extraction the diameter of the exhaust ducting should not be less than 150 mm If flat ducting is being used the cross sectional area must not be smaller than the cross sectional area of the exhaust connection All ducting pipework and fittings must be of non flammable materials The exhaust ducting should be as short and straight as possible Only use wide radius bends The exhaust ducting should not be kinked or compressed Ensure that all connections are strong and airtight Where ducting is horizontal it must be laid to slope away at at least 1 cm per metre This is to ensure that condensate cannot drain back into the cooker hood Connection for air extraction If the exhaust air is to be ducted into the open air the installation of a telescopic wall vent or roof vent available as an optional accessory is recommended dai2538 Ifthe exhaust air is to be ducted into a vent flue the ducting must be directed in the flow direction of the flue Important If the exhaust ducting is to run through rooms ceiling space etc where there may be great variations in temperature between the different areas the problem of condensation will need to be addressed The exhaust ducting will need to be suitably ins
15. hood be left on the fan will switch off automatically after 10 hours The lighting will remain on Pressing the On Off control will switch the fan back on again 14 Cleaning and care A range of Miele branded cleaning and conditioning products is available to order from Miele see back page for details or the via the internet at www miele shop com Before any cleaning or maintenance work is carried out disconnect the cooker hood from the mains supply Ensure that it is switched off at the isolator or it is switched off at the wall socket and the plug is withdrawn or the fuse from the fused spur connection unit is withdrawn or the mains fuse is disconnected or the screw out fuse is removed in countries where this is applicable Housing General The surfaces and controls are susceptible to scratches and abrasions Please observe the following cleaning instructions m All external surfaces and controls can be cleaned using a Miele E Cloth or with warm water and a little washing up liquid applied with a well wrung out soft soonge or cloth Only use a damp cloth as water could get into the appliance and cause damage m Wipe the surfaces dry using a soft cloth Do not use cleaning agents containing soda acids chlorides or solvents abrasive cleaning agents e g powder cleaners or cream cleaners and abrasive sponges as well as pot scourers or spo
16. lified electrician for advice Important This appliance is supplied for connection to an a c 230 V single phase 50 Hz supply The wires in the mains lead are coloured in accordance with the following code Green yellow earth Blue neutral Brown live WARNING THIS APPLIANCE MUST BE EARTHED Connection of this appliance should be made via a suitable isolator or a double pole fused spur connection unit which complies with national and local safety regulations and the On Off switch should be easily accessible after the appliance has been built in When switched off there must be an all pole contact gap of 3 mm in the switch including switch fuses and relays according to EN 60335 29 Operation with Control module DSM 400 The Miele DSM 400 control module can be used to combine the cooker hood with other components It enables the following Connection to a window contact switch If adequate ventilation to the room can only be ensured by having a window open when the cooker hood is in use at the same time as a heating appliance which depends on the air from the same room then the control module can be used to connect a window contact switch not supplied to the appliance Once connnected the cooker hood can only be operated when the window is sufficiently open see also Warning and Safety instructions When the window is closed the cooker hood fan cannot be switched on The indicator lamp
17. m good builders merchants Take care when ventilating the room through an open window that ventilation is not impaired by a closed blind or curtain The cooker hood can be set up to automatically switch on an air intake fan or open a motorised inlet flap when it is switched on The cooker hood can be set up to automatically switch off a heating appliance which also depends on the air from the room when it is or by other technical measures such as ensuring that the cooker hood can only be switched on when the heating appliance is switched off or vice versa switched on The Miele DSM 400 control module offers the possibility of combining other A ventilation brick alone is not generally sufficient to ensure safe ventilation The overall ventilation condition of the dwelling must be taken into account If in any doubt the advice of a competent builder or for gas a qualified gas fitter registered with an official gas safety body in accordance with national safety regulations GasSafe in the Uk must be sought components with the cooker hood see Operation with Control module DSM 400 It is available to purchase as an optional extra If in any doubt the advice of a competent builder or for gas a qualified gas fitter GasSafe registered in the UK must be sought If the hood is being operated in recirculation mode the above restrictions do not apply Warning and safety instructions Cor
18. nce remove solid particles grease dust etc from the kitchen vapours preventing soiling of the cooker hood The grease filters should be cleaned regularly at least every 3 4 weeks to avoid a build up of grease An oversaturated filter is a fire hazard dai2051 m To take out the grease filters release the locking clip on the filters lower the filters 45 unhook them at the back and remove them To avoid damaging the filters or the hob below make sure you hold the filters securely at all times when handling them Cleaning and care Cleaning the grease filters by hand m Clean the filters with a soft nylon brush in a mild solution of hot water and a little washing up liquid Do not use neat washing up liquid Do not use cleaning agents containing descaling agents powder cleaners cream cleaners or abrasive all purpose cleaners oven sprays Cleaning the grease filters in the dishwasher m Place the filters as upright as possible in the lower basket with the short sides upright and wash in a 65 C programme ensuring the spray arm is not obstructed If a Miele dishwasher is being used select the Sensor wash programme m Use a mild dishwasher detergent Depending on the cleaning agent used cleaning the filters in a dishwasher can cause permanent discolouration to the surface However this will not affect the functioning of the filters in any way m
19. nd cooker hood please note that a distance of 650 mm above electric cookers hobs may be preferable to give more working space under the hood Account should also be taken of the height of the person who will be using the hood most often The person should have sufficient space to work comfortably at the hob and also be able to reach the hood controls with ease 21 Appliance dimensions Please be aware that if positioned too high extraction will be inefficient If you want the top of the cooker hood telescopic extension piece to be mounted flush with the ceiling make sure there is adequate space below the appliance for working See maximum minimum appliance height 22 Drilling diagram 1 oo 0000 dai2690 This diagram illustrates where holes for 5 mm screws need to be drilled in the rear wall The dimension between the ceiling and the middle bracket can vary depending on the position of the vent cut out and the connection socket It should be installed as low as possible If the cooker hood is being secured directly to the wall please follow the drilling instructions given in the installation instructions supplied Installation Before installation it is important to read the information given on the following pages as well as the Appliance dimensions and the Warning and Safety instructions at the begin
20. nges which have been used previously with abrasive cleaning agents These will damage the surface material Important for appliances with stainless steel housing This infomation does not apply to the controls m Stainless steel surfaces can be cleaned using the Miele E Cloth or with a suitable non abrasive proprietary cleaning agent for stainless steel following the manufacturer s instructions on the packaging m To help prevent re soiling a conditioning agent for stainless steel can also be used Follow the manufacturer s instructions on the packaging Important for appliances with lacquered housing Special order finish It is very difficult to clean this type of surface without causing minor marks to the surface material This can become particularly noticeable with darker colours and if there is halogen lighting in the kitchen Cleaning and care Controls The controls may suffer discolouration or damage if soiling is left on them for too long Remove soiling straight away m Observe the General notes on cleaning earlier in this section Do not use stainless steel cleaning agents on the controls Important for appliances with glass surfaces m Glass surfaces can be cleaned using a proprietary non abrasive cleaning agent designed specifically for use on glass Do not use sharp metal tools oven sprays 16 Grease filters The re usable metal grease filters in the applia
21. ning of this booklet This is particularly crucial when using the cooker hood at the same time as a heating appliance that relies on oxygen from the same room to avoid the danger of toxic fumes building up Installation instructions See enclosed Installation sheet for instructions on how to install this appliance Protective foil on stainless steel appliances The housing components have protective foil around them to prevent them being damaged during transport m Please remove this foil before fitting the housing components It can be peeled off easily Dismantling Should the appliance ever need to be dismantled follow the installation instructions in reverse order as described on the installation sheet A lever is supplied to assist with the removal of the tower daio920 m After loosening the fixing screws on the tower push the lever between the tower and the telescopic extension piece to lever the tower out of its fixings 23 Installation Assembly parts Installation 3 protective sheets for use when fitting the tower 1 exhaust connection for exhaust ducting 150 mm 3 1 reducing collar for exhaust ducting 125 mm 1 non return valve for fitting into the exhaust connection on the motor unit not for recirculation mode Upper wall bracket for securing the extension piece Middle wall bracket for securing the ex
22. ouch the housing or the grease filters until the cooker hood has cooled down gt Do not use a steam cleaner to clean this appliance Steam could reach the electrical components and cause a short circuit Warning and safety instructions Correct installation gt Refer to the cooker or hob manufacturer s instructions as to whether a cooker hood may be operated above the cooker hob gt The minimum safety distances between the top of the cooker or hob and the bottom of the cooker hood given in the Appliance dimensions section of this booklet must be maintained unless the hob manufacturer states that a greater safety distance is required If more than one cooking appliance is fitted beneath the cooker hood and they have different minimum safety distances to the cooker hood select the greater distance gt Safety regulations prohibit the fitting of a cooker hood over solid fuel stoves gt All ducting pipework and fittings must be of non flammable material These can be obtained from the Miele Spare Parts department or from builders merchants gt The appliance must not be connected to a chimney or vent flue which is in use Neither should it be connected to ducting which ventilates rooms with fireplaces gt If exhaust air is to be extracted into a chimney or ventilation duct no longer used for other purposes seek professional advice Accessories gt Only use genuine Miele original spare part
23. rease filters 18 Replace the charcoal filter when it no longer absorbs kitchen odours effectively It should however be replaced at least every 6 months m Used charcoal filters can be disposed of with the normal household waste Cleaning and care Changing a halogen lamp m Before any cleaning or maintenance work disconnect the cooker hood from the mains supply Ensure that it is switched off at the isolator or it is switched off at the wall socket and the plug is withdrawn or the fuse from the fused spur connection unit is withdrawn or the mains fuse is disconnected or the screw out fuse is removed in countries where this is applicable Exercise caution when changing halogen lamps They get very hot during use and remain hot for some time after being switched off Let them cool down before you change them dai2328 dai2329 m To access the halogen lamp push the lamp cover gently upwards The cover will open and can be pulled down m Pull the old halogen lamp out of the connection socket m Using a cloth or glove push the new lamp 12 V 20 W G4 cap carefully into the connection socket Please follow the manufacturer s instructions m Push the cover back up and make sure it clicks into place Appliance dimensions 150 Do ff 690 1000 1 805 1115 2 4 A oo 0000
24. rect use gt Never use an open flame beneath the cooker hood To avoid the danger of fire do not flamb or grill over an open flame When switched on the cooker hood could draw flames into the filter Fat particles drawn into the cooker hood present a fire hazard B gt When using the cooker hood over a gas hob ensure that any burners in use are always covered by a pan Switch the cooking zone off when a pan is removed even for a short time Regulate the flame so that it does not burn up the sides of the pan Do not allow the pans to overheat excessively e g when using a wok The cooker hood can become damaged when exposed to excessive heat gt Always switch the cooker hood on when a cooking zone is in use otherwise condensation may collect in the hood which could cause corrosion B gt When cooking with oil or fat chip pans and deep fat fryers etc do not leave the pans unattended Never leave an open grill unattended when grilling Overheated oil and fat can ignite and could set the cooker hood on fire gt Do not use the cooker hood without the filters in place This way you will avoid the risk of grease and dirt getting into the appliance and hindering its smooth operation gt The filters should be regularly cleaned or changed as appropriate Saturated filters are a fire hazard See Cleaning and care gt The cooker hood can get very hot during cooking due to heat rising from the hob Do not t
25. s and accessories with this appliance If spare parts or accessories from other manufacturers are used this will invalidate the guarantee and Miele cannot accept liability The manufacturer cannot be held liable for damage caused by non compliance with these Warning and Safety instructions Guide to the appliance Guide to the appliance Telescopic extension piece 2 Tower Canopy Touch controls Grease filters Recirculation grille only for recirculation mode Hob lighting Charcoal filter special accessory for recirculation mode On Off control for the fan Controls to select fan power level On Off control for hob lighting Modes of operation The cooker hood works with air extraction RR The air is drawn in and cleaned by the grease filters and directed outside If the on site ventilation system does not have a non return flap the non return flap supplied with the appliance must be fitted in the exhaust socket in the motor unit Having a non return flap fitted in the ducting ensures that air once ducted to the outside cannot get back into the room again The flap is closed when the cooker hood is switched off When the cooker hood is switched on the non return flap opens for the cooking vapours to be blown directly outside 12 air recirculation available as an optional extra with a conversion kit and char
26. switch 0 20 0002 a 30 Potential free connection LL 30 Connection to a light switch i 31 After Sales Service 32 Technical data o iii pei anne 33 Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled Packaging e g cling film polystyrene and plastic wrappings must be kept out of the reach of babies and young children Danger of suffocation Disposal of your old appliance Electrical and electronic appliances often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance Please do not therefore dispose of it with your household waste Please dispose of it at your local community waste collection recycling centre or contact your dealer for advice Ensure that it presents no danger to children while being stored for disposal Warning and safety instructions This appliance complies with all relevant local and national safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the appliance please read these instructions carefully before using it for the first time They contain important information on the s
27. t of the external motor if possible or if the ducting is long above the exhaust connection on the cooker hood In the case of an external motor located inside the house fitting a silencer behind the external motor reduces the noise of the motor outside the house In all modes of operation the most effective noise reductions are achieved if two silencers are fitted one behind the other in the system Electrical connection All electrical work should be undertaken by a suitably qualified and competent person in strict accordance with current national and local safety regulations BS 7671 in the UK Installation repairs and other work by unqualified persons could be dangerous for which the manufacturer cannot be held liable Ensure power is not supplied to the appliance until after installation or repair work has been carried out Do not connect the appliance to the mains electricity supply by an extension lead These do not guarantee the required safety of the appliance The connection data is given on the data plate This is visible when the grease filters have been removed Ensure that this data matches the household mains supply If the switch is not accessible after installation depending on country an additional means of disconnection must be provided for all poles For extra safety it is advisable to protect the appliance with a suitable residual current device RCD Contact a qua
28. tension piece Lower wall bracket for securing the appliance unit Conversion kit for recirculation mode including directional unit and flexible aluminium hose with clips this is not included but is available as an optional extra see Technical Data 6 mp 8 screws 5 x 40 mm and 8 x S 8 plugs for securing the retaining plates to the wall The screws and plugs are designed for use in solid walls For other types of wall construction alternative fixings will be required Make sure the wall is strong enough to bear the weight of the cooker hood 2 x M6 self tapping nuts for securing the appliance Om 2 screws 3 9x 7 5 mm for securing the tower lt gt 1 lever for dismantling the tower Installation instructions 25 Connection for air extraction Important To avoid the danger of toxic fumes please observe the Warning and Safety instructions This is especially crucial when using the cooker hood at the same time as another heating appliance which relies on air from the same room The cooker hood should be installed according to local and national building regulations Seek approval from the building inspector where necessary 26 Only use smooth pipes or flexible hoses made from non flammable materials for the extraction ducting When using an external motor make sure that the exhaust ducting is sufficiently rigid The external motor can cause an underpressure which can r
29. ulated Condensate trap optional accessory dai1585 In addition to insulating the exhaust ducting we recommend that a suitable condensate trap is also installed to collect and evaporate any condensate which may occur Condensate traps are available for 125 mm or 150 mm ducting When installing a condensate trap ensure that it is positioned vertically and if possible directly above the exhaust connection The arrow on the housing indicates the direction of air flow Cooker hoods designed for use with an external motor EXT models have an integrated condensate trap 27 Connection for air extraction Silencer optional accessory 150 Zn dai2003 To achieve even further reductions in noise levels a special silencer can be fitted in the ducting system dai2341a 28 With air extraction The silencer not only reduces noise from the motor outside the house but also sounds from outside e g traffic noise For this reason the silencer must be positioned as close as possible to the ducting exit in recirculation mode The silencer needs to be positioned between the exhaust connection and the deflector Ensure there is adequate space in the tower for fitting air extraction with external motor To minimise noise from the motor in the kitchen the silencer should be positioned in fron
30. ve setting You can set the Intensive setting so that it only runs for 10 minutes before reverting automatically to level Ill m To set this option both the fan and the hob lighting must be switched off m Press the and controls at the same time for approx 10 seconds until the first power level indicator lamp lights up in the display m Then press in turn the Hob lighting control the symbol and the Hob lighting control again The indicator lamps for fan power levels and IV will flash if the automatic switch off for the Intensive setting is not activated m Press the control to activate auto matic switch off The indicator lamps for fan power levels and IV will now light up constantly Press the control to deactivate the automatic switch off function m Press the On Off control to confirm If you do not confirm within 4 minutes the cooker hood will automatically revert to the original setting Operation To switch the fan off D m Press the On Off control to switch the fan off The symbol goes out It is advisable to run the fan for a few minutes after cooking has finished to neutralise any lingering odours in the air whether you are using air extraction or recirculation mode Hob lighting m The hob lighting can be switched on and off independently of the fan by pressing the hob lighting control Safety switch off Should the cooker
Download Pdf Manuals
Related Search