Home

Miele T 4819 Ci L

1. Mains connection cable Four height adjustable screw feet 2 Condensed water container External drainage options e g via wash basin wash basin drain outlet or gully see External condensed Door can be fitted with a decor water outlet panel Control panel Service panel for condenser unit 37 Installation Installation site N Make sure the dryer door can be opened without hindrance after installation Building under a continous worktop in a kitchen run This tumble dryer is specially designed for installation under a continuous worktop run in a fitted kitchen N Niche height 820 930 mm When moving the dryer do not lift it by the drum door The dryer is supplied fitted with a cover plate instead of a machine lid The cover plate is necessary to ensure electrical safety and must not be removed 38 Slides can be used to protect the floor from damage when the machine is pushed into position or taken out for servicing The electrical socket must be located in an accessible position near the tumble dryer Please note Niche height Additional accessories required 820 mm None from Fit longer screw feet set to 830 840 mm approx 40 mm from One raising kit 870 885 mm from Two raising kits 915 930 mm these accessories are available to order The tumble dryer must not be used without the front pan
2. If you keep the Delay start button pressed in the time will continue to increase up to 24h 16 To begin delay start m Press the Start Stop button The Delay start indicator will light up constantly Delay start times of more than 10h will count down in hours and of less than 10h in minutes to the start of the programme The drum will turn briefly every hour to help prevent creasing To cancel alter delay start m Press the Start Stop button to cancel delay start m To alter the delay start time press the Delay start button repeatedly until the required delay period shows in the display m Press the Start Stop button to start the altered delay start time counting down from the beginning again To add laundry after the delay start time has started counting down While the delay start time is counting down you can still add laundry to the drum m Switch the dryer off Opening the door without switching the dryer off will cancel delay start m Open the door and add the laundry m Close the door and switch the dryer back on again Programme chart Cottons Max load 6 kg Extra dry Normal Fabric Single and multi layered cotton fabrics such as towelling T shirts underwear flannelette bed linen and baby clothes Note Select Extra dry for multi layered and very thick fabrics Do not use Extra dry for loopknit fabrics e g T shirts underwear baby clo
3. Operating instructions for condenser tumble dryer T 4819 Ci To avoid the risk of accidents en GB or damage to the appliance it is essential to read these instructions before it is installed and used for the first time M Nr 07 844 000 Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled Ensure that any plastic wrappings bags etc are disposed of safely and kept out of the reach of babies and young children Danger of suffocation Disposal of your old appliance Electrical and electronic appliances often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance Please do not therefore dispose it with your household waste R Please dispose of it at your local community waste recycling centre or contact your dealer for advice Ensure that it presents no danger to children while being stored for disposal Energy saving tips To avoid unnecessarily long drying times and high consumption of energy Make sure that your laundry is thoroughly spun before drying The higher the spin the greater the savings that can be made in energy and time during drying Load according to the optimum amount of
4. 20 cancelling the programme and then removing the laundry 20 Altering Delay start 20 ees 20 Adding or removing laundry after a programme has started 20 TIME TEMAINING icra tenes hawt ee ahha bas pe ab at 20 Electronic system lock 00 c eee 21 Contents Cleaning and care 0 00 0 cee 22 Emptying the condensed water COMIAINGD un areas ered eve eh ee dhe de ee ee ation ee ee 22 Cleaning the fluff filters 0 teas 23 Cleaning them whilst dry 0 0000 020 c eee 23 Cleaning them with water 0 0 0 0 2000000 24 Cleaning the tumble dryer n s asna eee 25 Cleaning the condenser unit sanaaa aaa 26 Removing the condenser unit 0 0 00 0 eee 26 Checking the condenser unit 0 200 0000 cece ee 27 Cleaning the condenser unit 0 00020 0000 cee 27 Replacing the condenser Unit iow at sete Pale ana 28 Problem solving guide 0 0 eee 29 Check and fault messages 0 6 0 eee 29 An unsatisfactory drying result 2 2 0 eee 32 Other Problems 2 80 be rarei ee ht heed best he oped Sheed hs 33 CHANGING MINE AMP 34 08 einate ida Sich RE bd Sopa A beh oes 35 After Sales service 0 00 0 36 PROG S cect Rea eh peters ee Er de tment ee ET enone 36 Future updates PC zu bh eon Mee ba ASE EAR EI Be Oe 36 Appliance guarantee a een nn bie a awh eon aes 36 Optional acceSsones ox dur eee ete hate nass hiylan ed
5. 57 Programmable functions Before you begin ensure that The tumble dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps Switch the dryer on Wait until the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button six times The Low temperature indicator light will flash 8 times briefly 58 A number to show which option is selected will appear in the display alternating with the letter P 0 On i Factory default setting Not in current programme the Automatic plus indicator light will also flash once e Off the Automatic plus indicator light will also flash twice Pressing the Start Stop button switches between the options Switch the dryer off The setting you have selected is now stored in memory You can change it again at any time To check the setting m Carry out steps to m Switch the dryer off after step Programmable functions Memory function The electronics will memorise any extra options selected for a programme The duration selected for the Warm air or Cool air timed drying programmes will also be stored in memory These settings will be selected automatically the next time the programme is chosen You can either accept these or change them by pressing the appropriate button Follow the st
6. Delicates Proofing Express Automatic plus Denim Shirts Gentle smoothing Extra dry O Normal O Hand iron O Machine iron O qua m Press the drying level button repeatedly until the indicator for the drying level you want lights up for almost all programmes Any of the four drying levels can be selected for the Cottons and Express programmes A more limited range is available when using other 14 programmes and with some the drying level is pre set and cannot be changed Note You can extend the range of the drying levels for some programmes see Programmable functions Woollens handcare This programme cannot be changed Selecting the duration of the timed drying Cool airand Warm air programmes The indicator light for the Delay start button will flash when the Cool air or Warm air programme is selected m Press the Delay start button repeatedly until the required duration shows in the display You can select the duration in stages for Cool air from 28 minutes up to 1 00 hour Warm air from 15 minutes up to 2 00 hours Select any Extra options Delay start m Low temperature Buzzer and Delay start see Extra options Delay start are selected by pressing the appropriate button Anti crease see next page is permanently switched on N B It is not possible to select Delay start when using the Warm air or Cool air programmes How to dry corre
7. Do not over dry these textiles When purchasing these garments it is advisable to take their shrinkage properties into account Minimum iron fabrics tend to crease more the larger the load This is also the case for garments made from very fine weave fabrics such as shirts or blouses If in doubt divide the garments into smaller loads Starched laundry can be dried in the tumble dryer To achieve the usual finish double the amount of starch should be used New dark coloured garments should be washed and dried separately from light coloured garments to avoid the danger of colours running and discolouring other garments or even plastic components in the dryer Dark coloured fibres can also settle on light coloured garments and vice versa How to dry correctly Brief instructions The headings numbered show the operating sequence and can be used as a brief guide to using your dryer Sort the laundry To ensure an even drying result separate out the washed laundry and sort it according to the drying level required the type of fibre or weave Size the moisture content after spinning N Make sure that objects e g detergent dispensing balls have been removed from the laundry They could melt and cause damage to the dryer or the laundry Check seams and stitching to ensure that padding and linings are intact Fasten duvet covers and pillow cases to p
8. Safety instructions Technical safety gt Before setting up the tumble dryer check it for any externally visible damage Do not install or use a damaged tumble dryer gt Before connecting the tumble dryer ensure that the connection data on the data plate voltage and connected load match the mains electricity supply If in any doubt consult a qualified electrician gt The electrical safety of this tumble dryer can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations It is most important that this basic safety requirement is present and regularly tested and where there is any doubt the household wiring system should be inspected by a qualified electrician Miele cannot be held liable for the consequences of an inadequate earthing system e g electric shock gt Do not connect the tumble dryer to the mains electricity supply by an extension lead Extension leads do not guarantee the required safety of the tumble dryer e g danger of overheating gt Unauthorised repairs could result in unforeseen dangers for the user for which Miele cannot accept liability Repairs should only be undertaken by a Miele approved service technician Ensure current is not supplied to the tumble dryer until after maintenance or repair work has been carried out gt Faulty components must only be replaced by genuine Miel
9. The setting you have selected is now stored in memory You can change it again at any time To check the setting m Carry out steps to m Switch the dryer off after step Programmable functions Altering the standard drying level in the Automatic plus programme The tumble dryer is designed to dry effectively using as little energy as possible However if you require the laundry to be drier or damper you can reduce or increase the default residual moisture in the Automatic plus programme Follow the steps 0 0 6 to programme and store in memory Before you begin ensure that The tumble dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps 8 0 Switch the dryer on Wait until the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button four times The Low temperature indicator light will flash six times briefly A number to show which option is selected will appear in the display alternating with the letter P O Increased residual moisture Laundry damper Standard residual moisture factory default setting the Automatic plus indicator light will also flash once e Reduced residual moisture Laundry drier the Automatic plus indicator light will also flash twice Pressing the Start Stop button switches betw
10. cleaned and which are still soiled with grease oil or other deposits Such as cosmetics lotions etc If items have not been thoroughly cleaned there is a danger that these might ignite when heated even after they have been removed from the dryer at the end of the programme items e g mops and floorheads which have been treated with inflammable cleaning agents or contain residues of acetone alcohol benzine petrol stain remover turpentine wax wax remover or other chemicals items which have been splashed with hair lacquer hair spray nail varnish remover or similar substances When washing such heavily soiled items ensure that you use sufficient detergent and select a high temperature If in doubt wash the items several times gt To prevent the risk of fire the following must not be dried in this tumble dryer items which have been cleaned using chemicals e g professional dry cleaning agents fabrics which contain a large proportion of rubber foam rubber or rubber like materials For example products made from latex foam rubber shower caps waterproof textiles rubberised articles and items of clothing and pillows with foam rubber filling damaged items which contain padding or fillings e g pillows jackets When damaged the filling can get out with the risk of it igniting in the dryer gt In many programmes the heating phase is followed by a cooling down phase to
11. cover The cover will open downwards The temperature resistant lamp should only be ordered from your Miele Dealer or the Miele Spare Parts Department 35 After Sales service Repairs In the event of any faults which you cannot remedy yourself please contact your Miele dealer or the Miele Service Department see back cover for contact details When contacting your dealer or the Service Department please quote the model and serial number of your appliance both of which are shown on the data plate situated on the right hand side below the drum aperture N B A call out charge will be applied for service visits where the problem could have been resolved as described in these instructions 36 Future updates PC The indicator or check light marked PC on the fascia panel is the interface used by the Miele service technicians during service work for testing purposes and for updating the appliance s programme data Appliance guarantee Please see the guarantee card supplied with your appliance Optional accessories Optional accessories for this dryer are available from your Miele Dealer the Miele Spare Parts Department or via the internet at www miele shop com Please note that telephone calls may be monitored and recorded for training purposes Installation Front view
12. display alternating with the letter P O Anti crease off 1 hour anti crease the Automatic plus indicator light will also flash once 2 hours anti crease factory default setting the Automatic plus indicator light will also flash twice Pressing the Start Stop button switches between the options Switch the dryer off The setting you have selected is now stored in memory You can change it again at any time To check the setting m Carry out steps to m Switch the dryer off after step 53 Programmable functions Altering the volume of the buzzer The buzzer has two volumes Follow the steps 0 0 6 to programme and store in memory Before you begin ensure that The tumble dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps 8 0 Switch the dryer on Wait until the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button three times The Low temperature indicator light will flash four times briefly 54 A number to show which option is selected will appear in the display alternating with the letter P O Normal buzzer factory default setting Loud buzzer the Automatic plus indicator light will also flash Pressing the Start Stop button switches between the options Switch the dryer off
13. iron Normal drier than Normal This programmable function is only available for programmes with drying levels Follow the steps 0 0 6 to programme and store in memory Before you begin ensure that The tumble dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps 8 0 Switch the dryer on Wait until the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button eleven times The Low temperature indicator light will flash on and off slowly once and then on and off quickly three times A number to show which option is selected will appear in the display alternating with the letter P O Factory default setting i Drying level range extended the Automatic plus indicator light will also flash Pressing the Start Stop button switches between the options Switch the dryer off The setting you have selected is now stored in memory You can change it again at any time To check the setting m Carry out steps to m Switch the dryer off after step To select the extended drying level m Select a programme m Press the drying level button repeatedly until one or two indicator lights come on Indicator lights Extra dry and Normal Normal Indicator lights Normal and Hand iron Slightly dry Indicator light
14. kg rom kWh min Cottons Normal 6 0 1000 60 ls 94 Cottons Normal 6 0 1200 53 3 05 86 6 0 1400 50 2 90 82 6 0 1600 48 2 55 74 6 0 1800 43 2 50 73 Cottons Normal Low temperature 6 0 1000 60 3 60 120 Cottons Hand iron 6 0 1000 60 2 65 71 Cottons Hand iron 6 0 1200 53 2 35 63 6 0 1400 50 2 20 60 6 0 1600 48 1 90 52 6 0 1800 43 1 80 51 Minimum iron Normal 3 0 1200 40 1 18 34 Minimum iron Normal Low temperature 3 0 1200 40 1 20 39 Minimum iron Hand iron 3 0 1200 40 1 05 31 Automatic plus Normal 4 5 800 50 2 70 114 Shirts Normal 2 0 600 60 1 25 43 Delicates Normal 2 0 700 50 1 20 81 Proofing Normal 2 0 800 50 1 25 59 Denim Normal 3 0 900 60 2 40 119 Gentle smoothing 1 0 1000 60 0 75 32 Woollens handcare 2 0 1000 50 0 15 4 Weight of dry laundry AEN 61121 2005 test programme All data was calculated using EN 61121 2005 unless otherwise stated Notes for test institutes Before testing in accordance with EN 61121 dry a 3 kg load of cotton laundry with 70 residual moisture as per the above standard using the Cottons Normal programme without any extra options Consumption data can vary from the nominal values given above depending on the size of the load type of textiles residual moisture levels after spinning fluctuations in the electricity supply and any extra options selected 49 Technical data Height Width Depth Suitable for stacking Weight Drum volume Maximum capacity Capacity o
15. letter P Follow the steps 0 0 6 to programme and store in memory Before you begin ensure that The tumble dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps Switch the dryer on Wait until the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button nine times The Low temperature indicator light will flash on and off slowly once and then on and off quickly once O Keypad tone deactivated factory default setting Keypad tone activated the Automatic plus indicator light will also flash Pressing the Start Stop button switches between the options Switch the dryer off The setting you have selected is now stored in memory You can change it again at any time To check the setting m Carry out steps to m Switch the dryer off after step 61 Programmable functions Adjusting the dryer s electronics for very soft water In some areas of the UK water is extremely soft which can affect the sensitivity of the control electronics If the dryer is installed in an area of very soft water you should contact your local water supplier for information and advice regarding water hardness and water conductivity If the water conductivity is less than 150 uS the following programmable function will need to be activated Importa
16. load 2 kg Normal Hand iron Fabric Shirts and blouses Low temperature Select the Low temperature option for delicate fabrics with the symbol on the care label Cool air Max load 6 kg Fabric Any item which only needs airing Warm air Max load 6 kg Items Voluminous and multi layered fabrics whose layers have different drying characteristics e g jackets pillows For drying individual items e g bath towels swimwear tea towels Note Do not select the longest drying time to start with Check the items as you are drying them to find the optimum time Tip You can use the Warm air programme to help remove odours from clean cotton clothing select a duration of between 1 2 and 1 hour Items must be suitable for drying in a tumble dryer Dampen the garments a little beforehand or add a fabric conditioner sheet Odours will not be removed as effectively from any parts of the garments which are made of synthetic fibres Low temperature Select the Low temperature option for delicate fabrics with the symbol on the care label Gentle smoothing Max load 1 kg Fabric Cotton and linen fabric Minimum iron mixed fibre cotton or synthetic fabrics e g trousers anoraks shirts Note Suitable for both dry and damp laundry Smooths out creasing caused during the spin cycle in the washing machine Remove garments as soon as the programme has finished so t
17. m When rinsing the condenser unit make sure you position it as shown in the next two illustrations m Use a shower head or similar to rinse the unit out as shown 27 Cleaning and care m Then flush the unit through from the front m Check the condenser unit again for any visible fluff and if necessary flush it through again until it has all gone m Also make sure the rubber seals are clean The rubber seals must not be removed and must be free of kinks Checking and cleaning the condenser unit housing m Remove any soiling still visible inside the housing unit by hand using a damp cloth Do not try and access areas you cannot reach by hand 28 Replacing the condenser unit m With the handle facing upwards push the condenser unit back into position in its housing m Turn the lever down to the horizontal position making sure that the hook on the lever clicks into the groove When replacing the inner cover after cleaning ensure that the rubber seal fits correctly into the groove m Replace the inner cover making sure the hooks locate correctly Hold it at an angle and push it gently downwards m Then turn the lever upwards into the horizontal position to lock the cover m Replace the service panel and press the upper edge until it clicks into position AA It is important to ensure that both the condenser unit and the cover are correctly positioned and locked otherwise water may leak from t
18. 0 0 0 eee 51 Altering the residual moisture level in the Cottons programme 51 Altering the residual moisture level in the Minimum iron programme 52 nti Grease us ns vata a nr er Re ae beara 53 Altering the volume of the buzzer 22 2 2oeneereerner ernennen 54 Altering the standard drying level in the Automatic plus programme 55 Extending the Cooling down Me u zusam 56 DIAN 5 2004 dase ea ee ee u AA E 57 Memory fundtion u ces an ne 59 Clean out airways indicator 0 0 0 0 ete 60 Keypad TONG arena da hh ett Ad det ee a ae 61 Adjusting the dryer s electronics for very soft water 0 2 0 0 00000 cee 62 Extending the range of the drying levelS 0 000000 cee ee 63 Warning and Safety instructions gt It is essential to read these instructions This tumble dryer conforms to current safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the tumble dryer please read these instructions carefully before using it for the first time They contain important information on its safety installation use and maintenance Keep these instructions in a safe place and ensure that new users are familiar with the content Pass them on to any future owner Correct application gt This tumble dryer is not designed for commercial use It is intended for use i
19. Before you begin ensure that The tumble dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps Switch the dryer on Wait until the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button eight times The Low temperature indicator light will flash on and off slowly once 60 A number to show which option is selected will appear in the display alternating with the letter P O Clean out airways indicator light deactivated Clean out airways indicator light comes on when there is a heavy build up of fluff the Automatic plus indicator light will also flash once Factory default setting the Automatic plus indicator light will also flash twice 3 Clean out airways indicator light comes on when there is only a light build up of fluff the Automatic plus indicator light will also flash three times Pressing the Start Stop button switches between the options Switch the dryer off The setting you have selected is now stored in memory You can change it again at any time To check the setting m Carry out steps to m Switch the dryer off after step Programmable functions Keypad tone An audible tone sounds each time a button is pressed A number to show which option is selected will appear in the display alternating with the
20. a dey 36 Installation 4 adeeb keke a eee Ree aan 37 FrOMU MIEW cases Atte ee Sindh thee a s ake ae Belek SM cede Lehen 37 Installationisitie 2 r28e ende se ead ete 38 Building under a continous worktop in a kitchen run 2 22 22 38 Leveling the applarniCe s crsa riiai are ee een 39 ROOM VEMUIALON ssn reret rn 39 Weasher dnverstacks 0 4 5 s0 he baht caw dad ere Pewee er A 39 Before moving the tumble dryer again e g when moving house 39 Matching the fascia panel to the height of adjacent drawer fronts 40 Removing the Spacer Danson pases anerkennen nina 40 Contents Fitting the front panel 2 eee 41 Front panel dimensions u 1 4 nun en ee eo 41 Fitting the front panel u 2240 need aa a ee wd Gas 41 Fitting a door front panel made by another manufacturer s sasaaa saana 42 Preparing the front panel sssr essere sinasin spad paapaa nennen 42 Preparing the fixing points 2 0 00 43 Fitting a plinth facing 6 eee 44 External condensed water outlet 6 eee 45 Arranging the drain NOSE 24 2 0 enka an bad ae REM Sees ween E 45 External drainage via a sink or gully 0 ee 46 Installation conditions requiring a non return valve 0 ee 46 Electrical connection 0 00 ccc eee 48 Electrical connection U K eee 48 Consumption data 0 0 00 0 eee 49 Technical data 0 0 eee 50 Programmable functions 0 0
21. al moisture factory default setting the Automatic plus indicator light will also flash once e Reduced residual moisture Laundry drier the Automatic plus indicator light will also flash twice Pressing the Start Stop button switches between the options Switch the dryer off The setting you have selected is now stored in memory You can change it again at any time To check the setting m Carry out steps to m Switch the dryer off after step Programmable functions Anti crease Anti crease helps prevent creasing if laundry is not normally removed im mediately after the end of a programme The anti crease function is activated when the tumble dryer is delivered You can shorten the duration of the anti crease phase or deactivate it if wished is used in all programmes except Woollens handcare should be left activated Follow the steps 0 0 6 to programme and store in memory Before you begin ensure that The tumble dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps 8 0 Switch the dryer on Wait until the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button twice The Low temperature indicator light will flash 3 times briefly A number to show which option is selected will appear in the
22. at The tumble dryer is switched off The door is closed m The procedure is the same as for activating the lock Carry out steps to as described previously At step the indicator light for the Low temperature button will stop flashing and the key symbol B a will go out The electronics are no longer locked 21 Cleaning and care Emptying the condensed water container The condensed water will be collected in the condensed water container unless the dryer has been connected for external drainage see Installation Empty the condensed water container after every drying programme The Empty container indicator will light up if the maximum level of the condensed water container is reached The indicator light will go out when the door is opened and closed again m Pull out the condensed water container m To prevent water running out hold it at the front and towards the back and keep it in a horizontal position when carrying it 22 m Empty the container m Replace the container in the dryer N Condensed water should not be consumed It could lead to health problems for people and animals Condensed water can be put to household use e g in a steam iron or humidifier To ensure that any residual particles of fluff in the condensed water are removed before use pass it through a fine sieve or paper filter first Cleaning and care Cleaning the fluff fil
23. ay now vary from the actual drying time Electronic system lock The system lock prevents the dryer being used without your knowledge It can be activated if wished The dryer s electronics are then locked The dryer can still be switched on but a programme cannot be started If an attempt is made to start a programme the indicator light for the Low temperature button will come on and a key symbol o will appear in the display The door is not locked and can be opened at any time To activate the lock Before you begin first ensure that The tumble dryer is switched off The door is closed Press the Low temperature button and keep it pressed in whilst carrying out steps to Press the amp button The Automatic plus indicator light will come on Slowly turn the programme selector three positions stage by stage ina clockwise direction Each of the three programme indicator lights must come on one after the other Now slowly turn the programme selector six positions stage by stage in an anti clockwise direction Each of the six programme indicator lights must come on one after the other The indicator light for the Low temperature button will flash and the key symbol o will appear in the display Release the Low temperature button The electronics have now been locked m Switch the dryer off To deactivate the lock Before you begin first ensure th
24. ctly Start the programme The Start Stop button will flash when a programme is being selected The flashing indicates that a programme can be started m Press the Start Stop button The Start Stop button will now light up constantly Drying will appear in the display and the Perfect Dry indicator will flash The indicator will go out after approx 1 minute and the estimated programme duration will appear in the display Note The duration shown in the display is an estimate and can vary Before the end of a programme The Perfect Dry indicator will light up There is a cooling down phase at the end of the drying sequence Cooling down will appear in the display The programme will not finish until the cooling down phase has been completed There is no cooling down phase at the end of the Woollens handcare programme Only with programmes with drying levels exception Gentle smoothing Remove the laundry when the programme has finished 0 and Finish will appear in the display to indicate that the programme has finished The buzzer if selected will sound at intervals The drum will continue to rotate at intervals for up to two hours to prevent laundry creasing if you do not wish to remove it immediately anti crease There is no anti crease phase at the end of the Woollens handcare programme m Press the Door button m Open the door m Remove the laundry Check that all items have been r
25. e at the bottom without spacer bars the front panel must be correspondingly higher if width b increases measurement a must also be increased b 592 mm gt a 21 5 mm b 593 mm a 22 0 mm b 594 mm a 22 5 mm b 595 mm a 23 0 mm b 596 mm a 23 5 mm H height of adjacent furniture unit doors 42 Installation For right hand hinging only front panel shown decor side face down upper edge at the bottom if width b increases measurement a must also be increased b 592 mm a 21 5 mm 593mm gt a 22 0 mm b 594 mm gt a 22 5 mm b 595 mm gt a 23 0 mm b 596 mm gt a 23 5 mm H height of adjacent furniture unit doors Drill the two hinge holes 35 mm 15 5 mm deep in the back of the front panel Next drill the four smaller holes 7 mm 10 mm deep in the back of the front panel Shorten the front panel from the bottom to height H Preparing the fixing points Hold the pre drilled front panel in the correct position in front of the machine door Mark the fixing points on the back of the front panel through the holes in the machine door plate see arrows in the illustration Remove the front panel Now drill holes 2 5 mm 10 mm deep in the back of the front panel 43 Installation Fitting a plinth facing The gap between the lower edg
26. e of the tumble dryer plinth and the floor can be closed up using a suitable kitchen furniture plinth facing The tumble dryer plinth has a special groove in which a plinth facing can be fitted Plinth facing dimensions Length 592 596 mm Thickness 8 mm Height H The plinth facing height must be calculated after aligning the height of the appliance with the screw feet or after fitting the raising kit s Installation m Calculate height H from the floor up into the groove on the underside of the tumble dryer m Cut the plinth facing to size m Slide it into the groove 44 Useful tip If the dryer is fitted on a raising kit you can use double sided adhesive tape on the back of the plinth facing to secure it to the raising kit Installation External condensed water outlet General notes When drying is in progress condensed water is pumped into the condensed water container through the drain hose at the back of the dryer The condensed water can also be drained off directly if the dryer is installed near a sink drain outlet etc so that the condensed water container does not have to be emptied Drain hose length 1 00 m Extension hose 2 00 m accessory Maximum delivery head 1 50 m Maximum drain hose length 4 00 m A If the on site water drainage system is not fitted with a non return valve or an appropriate air gap an air gap or the non retu
27. e original spare parts Only when these parts are fitted can the safety standards of the tumble dryer be guaranteed gt If the connection cable is faulty it must only be replaced by a Miele approved service technician to protect the user from danger gt In the event of a fault or for cleaning purposes the tumble dryer is only completely isolated from the electricity supply when it is switched off at the wall socket and the plug is withdrawn or itis switched off at the mains or the mains fuse is disconnected or the screw out fuse is removed in countries where this is applicable gt This tumble dryer may only be used in mobile installations such as ships if a risk assessment of the installation has been carried out by a suitably qualified engineer P In countries where there are areas which may be subject to infestation by cockroaches or other vermin pay particular attention to keeping the tumble dryer and its surroundings in a clean condition at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee gt Do not make any alterations to the tumble dryer unless authorised to do so by Miele Warning and Safety instructions Correct use gt To prevent the risk of fire the following textiles must not be dried in this tumble dryer items which have not been washed items such as workwear which have not been thoroughly
28. e until after installation work has been carried out The appliance is supplied with a mains cable with moulded plug ready for connection to a 230 240V mains supply Please ensure the connection data quoted on the data plate match the household mains supply Connection should be made via a suitable switched socket which is easily accessible after installation For extra safety it is advisable to protect the appliance with a suitable residual current device RCD Contact a qualified electrician for advice Do not connect via an extension lead Extension leads do not guarantee the required safety of the appliance e g danger of overheating 48 Non rewireable plugs BS 1363 The fuse cover must be refitted when changing the fuse and if the fuse cover is lost the plug must not be used until a suitable replacement is obtained The colour of the correct replacement cover is that of the coloured insert in the base of the plug or the colour that is embossed in words on the base of the plug as applicable to the design of plug fitted Replacement fuses should be ASTA approved to BS 1362 and have the correct rating Replacement fuses and fuse covers may be purchased from your local electrical supplier WARNING THIS APPLIANCE MUST BE EARTHED Consumption data Load Final spin speed Residual Energy Duration in a domestic washing moisture machine
29. een the options Switch the dryer off The setting you have selected is now stored in memory You can change it again at any time To check the setting m Carry out steps to m Switch the dryer off after step 55 Programmable functions Extending the cooling down time The cooling down phase which takes place before the end of a programme can be extended by 5 or 10 minutes if required This makes the garments easier to handle The cooling down time can only be extended for programmes with drying levels Follow the steps 0 0 6 to programme and store in memory Before you begin ensure that The tumble dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps 8 0 Switch the dryer on Wait until the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button five times The Low temperature indicator light will flash seven times briefly 56 A number to show which option is selected will appear in the display alternating with the letter P O Cooling down time not extended factory default setting Cooling down time extended by five minutes the Automatic plus indicator light will also flash once e Cooling down time extended by ten minutes the Automatic plus indicator light will also flash twice Pressing the Sta
30. el in place If the kitchen run has a continuous furniture plinth in place a gap must be made for the tumble dryer Installation Levelling the appliance m Turn the 4 screw feet to adjust the dryer to the correct height and level Longer screw feet are available as an optional accessory Unscrew and remove the feet supplied with the appliance before fitting the longer screw feet The cover plate on the dryer must be aligned horizontally underneath the worktop The ventilation gaps in the plinth must not be covered over This would hinder a sufficient flow of air to the dryer Room ventilation Air taken in for use in the drying process will be warm when it is expelled from underneath the dryer This expelled air heats up the air in the room It is therefore very important to ensure that the room is adequately ventilated particularly if the dryer is located in a small room Otherwise running times and energy consumption could be increased Washer dryer stack The tumble dryer can also be combined with a Miele washing machine in a washer dryer stack The appropriate WTV stacking kit available to order to match your dryer is required N The stacking kit must be fitted by a suitably qualified fitter Before moving the tumble dryer again e g when moving house After each use a small quantity of condensed water will collect in the area around the pump This water can run out if the dryer is ti
31. emoved from the drum If items are left in the dryer they could be damaged by overdrying when the dryer is next used If the dryer is switched on at the mains and the door is opened the drum lighting will come on It will go out a few minutes later to save energy m Switch the dryer off by pressing the A button m Clean the fluff filters m Close the door m Empty the condensed water container unless the dryer has been connected for external drainage m The condenser unit should be checked and cleaned on a regular basis see Cleaning and care Extra options Delay start Extra options Low temperature Delicate and minimum iron fabrics with the Q symbol on the care label e g acrylic garments are dried at a lower temperature The programme duration is longer On some programmes Low temperature is permanently activated and so cannot be deselected Buzzer A buzzer sounds at intervals for a maximum of 1 hr to let you know the programme has finished A continuous alarm will sound if there is a fault even if the buzzer has been switched off Delay start You can delay the start of a programme by 30 minutes up to 24 hours m Select a programme m Press the Delay start button repeatedly until the required delay period shows in the display The Delay start indicator light will flash Times of up to 10h are selected in steps of half an hour and more than 144 in one hour steps
32. ensure that the items are not too hot to handle when you remove them this also avoids the danger of the laundry self igniting The programme is not finished until the cooling down phase has been completed Ensure that you always wait until the end of the programme before removing the laundry gt Warning Do not switch the tumble dryer off before the end of the drying programme If this was done and the laundry was then removed immediately it could give off a great amount of heat gt Fabric conditioner and similar products must be used according to the instructions on the manufacturer s packaging Warning and Safety instructions gt The dryer must not be used without the fluff filters in place or if the fluff filters are damaged in any way gt The fluff filters must be cleaned regularly gt The dryer must not be used without the condenser unit in place gt The fluff filters must be thoroughly dried after cleaning Damp or wet filters could cause operational faults gt Do not install the tumble dryer in a room where there is a risk of frost occurring At temperatures around freezing point the tumble dryer may not be able to operate properly There is a risk of damage if the condensed water is allowed to freeze in the pump hoses and or condensed water container The ambient room temperature should be between 2 C and 35 C gt If the water is drained externally through the drain hose instead o
33. ent residue hair and fine fluff from the dryer can get through the fluff filters and block the condenser unit Dust from the room in which the dryer is installed can also get into the condenser unit and cause a blockage Check the condenser unit at least once a year Always check it if the Clean out airways indicator light comes on Clean it if necessary m Turn the lever on the inner cover downwards to the vertical position Removing the condenser unit m Tilt the cover forwards m Remove it by pulling it diagonally upwards m Open the service panel Hold the panel securely when doing this m Now remove the panel by pulling it diagonally upwards and place it to m Turn the lever on the condenser unit upwards to the vertical position so that the hook on the lever is no longer in the groove at the bottom of the condenser unit housing one side 26 Cleaning and care m Pull the condenser unit out of its housing by the handle Checking the condenser unit m Hold the condenser unit up to the light as shown m Check to see if there is any fluff inside it The arrows in the illustration above indicate where to look If you cannot see any fluff m Replace the condenser unit see following page If you can see some fluff m Clean the condenser unit as described below Cleaning the condenser unit
34. ents below the door are blocked Remove any objects that are blocking the vents The fluff filters are clogged up with fluff or were still wet when they were replaced Remove any fluff The fluff filters must be completely dry Detergent residues hair and fine fibres can block the condenser unit Check the condenser unit from time to time and clean it if necessary The laundry has not been spun sufficiently Make sure that your laundry is thoroughly spun at the appropriate spin speed in the washing machine The tumble dryer has been overloaded Do not exceed the maximum load for the programme selected Metallic components e g zips have prevented the dryer from registering the correct moisture level in the laundry Open zips next time If the problem occurs again dry garments with long zips using the Warm air programme timed drying 33 Problem solving guide condenser unit has been cleaned been locked properly and or the condenser unit has not been positioned correctly Fluff has collected in the condenser unit housing Problem Possible cause Remedy Water leaks from the The inner cover of the Ensure that the dryer after the condenser unit has not condenser unit is positioned correctly and lock the inner cover Check the rubber seals Use a cloth to remove any visible fluff from the inside of the co
35. eps 0 0 6 to programme and store in memory Before you begin ensure that The tumble dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps 8 0 Switch the dryer on Wait until the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button seven times The Low temperature indicator light will flash 9 times briefly A number to show which option is selected will appear in the display alternating with the letter P O Memory deactivated factory default setting Memory activated the Automatic plus indicator light will also flash Pressing the Start Stop button switches between the options Switch the dryer off The setting you have selected is now stored in memory You can change it again at any time To check the setting m Carry out steps to m Switch the dryer off after step 59 Programmable functions Clean out airways indicator Fluff should be removed after drying The Clean out airways indicator will remind you to clean the filters when a certain amount of fluff has collected in the filters You can decide at what level of fluff this reminder should be given You will have an idea of how often this should be done after a few drying programmes Follow the steps 0 0 6 to programme and store in memory
36. f being collected in the condensed water container make sure the drain hose is securely attached if you hang it ina sink or basin to avoid the hose slipping and the water causing damage gt Condensed water is not drinking water It can cause health problems in both people and animals gt Always keep the area around the tumble dryer free of dust and fluff Dust drawn into the tumble dryer can cause blockages in the condenser unit over time gt Do not let anyone sit or lean on the door as this can cause the tumble dryer to tip up gt Always close the door after use This way you will avoid the danger of children climbing onto or into the dryer or hiding things in it pets or other small animals climbing into it gt The tumble dryer must not be hosed down Accessories gt Only use genuine Miele spare parts and accessories with this appliance If non Miele parts are used guarantee performance and product liability claims may be invalidated Miele cannot be held liable for damage caused by non compliance with these Warning and Safety instructions Operating the tumble dryer Control panel Extra dry O Drying Cooling down Finish Co Pertect Dry O Normal Hand iron O Machine ironO C Cottons Automatic plus O Minimum iron Denim O Delicates Shirts O Delay start Buzzer Low A temperature O Empty container C
37. f condensed water container Drain hose length Maximum delivery head Maximum drain hose length Length of connection cable Voltage Connected load Fuse rating Lamp wattage Energy consumption Test certificates awarded 50 820 mm 595 mm 575 mm Yes 54 kg 100 litres 6 kg dry weight approx 3 5 litres 950 mm 1 5m 4m 2m see data plate see data plate see data plate plug see data plate see Consumption data see data plate Programmable functions Altering the residual moisture level in the Cottons programme The tumble dryer is designed to dry effectively using as little energy as possible However if you require the laundry to be drier or damper you can reduce or increase the default residual moisture in the Cottons programme Follow the steps 0 0 6 to programme and store in memory Before you begin ensure that The tumble dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps 8 0 Switch the dryer on Wait until the Start Stop button lights up constantly and then release the Start Stop button The Low temperature indicator light will flash once briefly A number to show which option is selected will appear in the display alternating with the letter P O Increased residual moisture Laundry damper Standard residual moisture factory default setting the Au
38. g down or Finish flashes in the display The buzzer sounds No obvious cause Switch the dryer off and then on again Then start the programme again If the programme stops again and Cooling down or Finish flashes again there is a fault Contact the Miele Service Department 29 Problem solving guide Problem Possible cause Remedy The Clean out airways indicator light comes on This indicator light comes on to warn you that the dryer is not working efficiently Possible cause the fluff filters are clogged with fluff or with detergent residues Cleaning the fluff filters is usually all that is required However if the Clean out airways indicator light does not go out after you have cleaned the filters then also check all the possible causes described under The drying process goes on too long or even switches off To switch off the indicator light With the dryer switched on open and close the door The Clean out airways indicator light can be deactivated see Programmable functions The programme stops The Clean out airways indicator light comes on The buzzer sounds See above for possible causes and their remedies To switch off the indicator light With the dryer switched on open and close the door Then start the programme again If the Clean out airways indicator light comes on again contact the M
39. hat they are easy to iron Low temperature Low temperature cannot be deselected Weight of dry laundry Changing the programme sequence Once a programme has started changing the programme You cannot change to another programme once a programme has started this prevents unintentional alterations You will need to cancel the current programme before you can select a new one cancelling the programme and then selecting a different programme m Press the Start Stop button The items will be cooled down depending on the temperature reached and how long they have been dried for If you press the Start Stop button again during the cooling down phase Finish will light up in the display m Press the Door button m Close the door m Select another programme and start it cancelling the programme and then removing the laundry m Proceed as described in Adding or removing laundry after a programme has started below m Switch the dryer off after closing the door 20 Altering Delay start m See Delay start Adding or removing laundry after a programme has started m Press the Door button m Open the door N Danger of burning Do not touch the back of the drum when adding or removing items The drum and the items can get very hot m Add or remove items as required m Close the door m Press the Start Stop button Time remaining The time left shown in the display m
40. he dial out of the door opening as shown Do the same on the other side m Rinse all the filters under hot running water m Then shake the filters until no more water droplets are visible m Dry the filters thoroughly with care m Clean the area underneath these filters e g with a vacuum cleaner 24 Do not replace them if they are damp or wet Damp or wet filters could cause operational faults m Push the large filter back into the door holder until it clicks into position Ensure it is facing the correct way m Replace the filters in the door opening by first inserting them at the bottom and then pressing them into place at the top m Lock both dials Cleaning and care Cleaning the tumble dryer Disconnect the tumble dryer from the mains electricity supply Miele branded cleaning and conditioning products are available to order via the internet on www miele shop com m Clean the housing and control panel with a slightly damp cloth and a mild detergent or soapy water m The drum and other stainless steel parts can be cleaned with a suitable stainless steel cleaner following the manufacturer s instructions Do not use solvents abrasive cleaners glass cleaners or all purpose cleaners These could damage plastic sufaces and other parts The tumble dryer must never be hosed down m Dry all parts with a soft cloth 25 Cleaning and care Cleaning the condenser unit Deterg
41. he dryer Problem solving guide With the help of the following notes minor faults in the performance of the appliance some of which may result from incorrect operation can be put right without contacting the Service Department Repair work to electrical appliances should only be carried out by a suitably qualified person in strict accordance with current local and national safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work Check and fault messages Problem Possible cause Remedy The programme stops and and Finish appear in the display The buzzer sounds This is not a fault The electronic unit has recognised that there is no laundry in the drum and cancelled the programme Drying individual garments or items which are already dry can also cause the programme to be cancelled Use the Warm air programme timed drying to dry individual items To select anew programme switch the dryer off and on or Open the door place more laundry in the drum then close the door The Low temperature indicator light starts flashing after the dryer has been switched on and l o appears in the display The electronic system lock is activated You will need to deactivate the system lock before the dryer can be used see Electronic system lock The programme stops and Coolin
42. ially dry beforehand Notes on laundry care Garment care label symbols Drying Normal higher temperature Reduced temperature Select Low temperature for delicate textiles Ri Do not tumble dry Ironing A Very hot A Hot A Warm a Do not iron Tips on drying Always observe the maximum recommended loads given in the Programme chart Never overload the drum Overloading can cause unnecessary wear and tear to the laundry give a disappointing drying result and cause more creasing Do not put soaking wet items into the tumble dryer Spin fabrics for at least 30 seconds before drying Open jackets so that they can dry evenly Use the Automatic plus programme for drying mixed loads of cotton and minimum iron fabrics Woollens and wool blends tend to become matted and shrink if dried in a tumble dryer They can however be fluffed up using the Woollens handcare programme 12 Down filled garments have linings which have a tendency to shrink depending on the quality of the item They can be partially dried using the Gentle smoothing programme Pure linen should only be machine dried if specified as suitable by the manufacturer on the care label as the surface of the fabric may otherwise become rough Loopknit garments e g T shirts and underwear tend to shrink depending on their quality
43. iele Ser vice Dept The Empty container indicator light comes on The buzzer sounds The condensed water container is full or there is kink in the drain hose Empty out the condensed water container Check the drain hose To switch off the indicator light With the dryer switched on open and close the door 30 Problem solving guide Problem Possible cause Remedy The Start Stop button is The dryer is in Standby See Programmable flashing slowly and the mode functions display is dark This is quite normal and not indicative of any fault Sometimes a programme cannot be started and the corresponding programme indicator light does not light up No obvious cause Switch the dryer off and back on again Select one of the programmes that would not start If it still will not start there is a fault Contact the Miele Service Department Not all the programmes are unavailable Select one that is available in the meantime The Start Stop button flashes on and off The flashing indicates that a programme can be started After the programme has started the flashing will change to a constant light 31 Problem solving guide An unsatisfactory drying result Problem Possible cause Remedy The laundry is not The load consisted of Finish drying using the sufficiently dry different fabrics Wa
44. inished and leave to finish drying at room temperature Low temperature Low temperature cannot be deselected Proofing Max load 2 kg Normal Fabric For drying microfibre fabrics skiwear fine closeweave cotton garments poplin or tablecloths which are suitable for drying in a tumble dryer and have been treated to provide a water and dirt resistant finish Note This programme includes a proofing fixing phase Only use proofing agents containing fluorochemical compounds which are stated by the manufacturer as being suitable for use on membrane textiles Do not dry items which have been treated with proofing agents containing paraffin Fire hazard Express Max load 3 5 kg Extra dry Normal Hand iron Machine iron Fabric Fabrics which can tolerate high temperatures with the symbol on the care label and which can be dried in the Cottons programme Note The programme duration is shorter Automatic plus Max load 4 5 kg Normal Hand iron Fabric Mixed loads of garments suitable for the Cottons and Minimum iron programmes Sort according to colour Denim Max load 3 kg Normal Hand iron Fabric Denim garments e g jeans jackets skirts shirts Low temperature Select the Low temperature option for delicate fabrics with the symbol on the care label Weight of dry laundry 18 Programme chart Shirts Max
45. laundry recommended for the programme being used see Programme chart Underloading is uneconomical Overloading gives a poorer quality of drying and may cause unnecessary creasing Make sure the room in which the dryer is located is well ventilated Make sure the fluff filters are clean before using the dryer Check the condenser unit from time to time and clean it when necessary Contents Caring for the environment 0 0 00000 c cece eee 2 Warning and Safety instructions 0 000000 cee eee 6 Operating the tumble dryer 0 00 0 10 COMMON Panel ee i e ee egw ne eran hee eed Se btwn ae aa She eed Aw ee 10 Notes on laundry care 0 0 eee 12 Garment care label symbols 0 2 0 2 60 e ee 12 TIPS ON GIVING rn a ese gee th rn doe ha argue do a due Mae ae a ad are 12 How to dry correctly 6 0 0 0 eee 13 Brief instr ctions sser amerma a ra er a A E E A EA N 13 Extra options Delay start Luau a 16 EXTA ODIOS sarete 2 na ae a RAO a eed ae S 16 LOW temperatu Gsus rrari a EE RRES EE ie ee 16 BUZZO ee ee a e ee ee Are 16 Delay SIAN neede ne een e ee ee ee aed Beet 16 Programme chart 0 0 00 carare i si riOa EREE eee 17 Changing the programme sequence 0 0000 e eens 20 Once a programme has started 0 eee 20 changing the programme 0 6 0 ee 20 cancelling the programme and then selecting a different programme
46. lean out airwayls o Woollens Timed drying o handcare cool air I D 7 Timed drying oe O Proofing Waren aie fe Express Gentle smoothing O Door Low temperature button Delicate fabrics are dried at a lower temperature 2 Drying level button with indicator lights to show the drying level selected Display See next page Delay start button This button is used for Delaying the start of a programme Selecting the duration of the timed drying Warm air programme Buzzer button An audible tone sounds at the end of the programme Perfect Dry indicator For all drying level programmes See next page 10 Check lights For a description of these see Problem solving guide After sales service Start Stop button For starting or cancelling a programme The button flashes while a programme is being selected and then lights up constantly when the programme has started Programme selector with indicator lights to show the programme selected Door button Pressing this button will open the door even when the dryer is switched off at the mains ay LA button For switching the appliance on and off Operating the tumble dryer The display shows Programme duration Programme stage Drying Cooling down Finish Check and fault messages The following are also selected via the display Duration of the Warm air and Cool air prog
47. n f the tumble dryer is to be connected to a drainage system already in use by another appliance e g a dishwasher or washing machine 46 Example Connection to a sink drain outlet The drain hose with non return valve fitted can be connected directly to a suitable sink drain outlet m Remove the following from the back of the dryer at the bottom Adapter 1 and hose clip 3 behind it Installation 1 Adapter 2 Nut 3 Hose clip 4 Extension hose accessory 5 Non return valve accessory 6 Tumble dryer drain hose m Fit adapter 1 to the sink drain outlet using nut 2 If this nut has a flat disc in it you should take the disc out first m Attach the end of the extension hose 4 to adapter 1 m Use a screwdriver to tighten hose clip 3 up close to the nut N Non return valve 5 has to be fitted with the arrow pointing in the direction of flow i e towards the sink Otherwise water will not drain out of the machine m Fit non return valve 5 to the drain hose on the dryer 6 make sure it is fitted correctly see arrow on non return valve m Secure the non return valve using hose clips accessory 47 Electrical connection Electrical connection U K All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current national and local safety regulations BS 7671 in the UK Ensure power is not supplied to the applianc
48. n domestic households and in similar working and residential environments such as Shops Offices and showrooms and by residents in establishments such as Hostels and guest houses P gt It must only be used as a domestic appliance to dry items which have been washed in a water solution and which are marked on the manufacturer s care label as being suitable for tumble drying If using Dry cleaning kits for freshening up garments in a tumble dryer do so at your own risk and follow the instructions on the packaging Any other usage is not supported by the manufacturer and could be dangerous Miele cannot be held liable for damage resulting from incorrect or improper use or operation of the tumble dryer gt This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience or knowledge unless they are supervised whilst using it or have been shown how to use it correctly by a person responsible for their safety Safety with children gt Keep children away from the tumble dryer at all times It is not a toy To avoid the risk of injury do not allow them to play on or near it or to play with its controls Supervise children whilst you are using it gt Older children may only use it if its operation has been clearly explained to them and they are able to use it safely recognising the dangers of incorrect use Warning and
49. ndenser unit housing The programme does not start No obvious cause Is the dryer switched on Is the plug correctly inserted into the socket and switched on Is the door closed properly Has the fuse or circuit breaker tripped Power cut A programme which was running previously will continue automatically when power is restored to the tumble dryer as long as the Cooling down phase had not been reached The interior drum lighting does not come on The lighting switches off automatically to save energy Switch the dryer off and then on again If the lamp needs to be replaced follow the instructions in Changing the lamp 34 Problem solving guide Changing the lamp The lamp specification and Disconnect the tumble dryer from maximum wattage is stated on the the mains electricity supply data plate and on the lamp cover m Open the door m Replace the lamp You will find the interior lamp cover at m To close the cover push it upwards the top of the drum aperture and press it on the left and right until you hear it click into position N Ensure that it is fitted into position securely as any moisture could cause a short circuit m Insert a suitable tool such as a wide bladed screwdriver under the side edge of the lamp cover as illustrated m Apply alittle pressure and whilst doing so turn your wrist in the direction of the arrow to open the
50. nt This programmable function should not be activated if despite the water being extremely soft as would be the case if a water softener were used its conductivity is greater than 150 US Follow the steps 0 0 6 to programme and store in memory Before you begin ensure that The tumble dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps 8 0 Switch the dryer on Wait until the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button ten times 62 The Low temperature indicator light will flash on and off slowly once and then on and off quickly twice A number to show which option is selected will appear in the display alternating with the letter P Factory default setting Adjusted for very soft water the Automatic plus indicator light will also flash Pressing the Start Stop button switches between the options Switch the dryer off The setting you have selected is now stored in memory You can change it again at any time To check the setting m Carry out steps to m Switch the dryer off after step Programmable functions Extending the range of the drying levels You can extend the range of the drying levels for many of the programmes Machine iron drier than Machine iron Slightly dry drier than Hand
51. nt panel The appliance front can be fitted with a m Open the door door panel to match other kitchen units m Hold the front panel in the correct position in front of the appliance If fitted in a Miele kitchen the door door panel can be ordered pre drilled with the necessary fixing holes If fitted in a non Miele kitchen a suitable panel will have to be drilled to suit by a qualified kitchen fitter See Fitting a door front panel made by another manufacturer for details on preparing and drilling the fixing holes Front panel dimensions Width 592 596 mm Thickness 17 to 19 mm corresponding to the thickness of the adjacent unit door front panels m Screw the front panel to the machine door If all the spacer bars have been removed You can also make use of the 3 holes at the top of the door plate to screw the front panel to the door plate Height The height of the door front panel corresponds to the door height H of the adjacent units 41 Installation Fitting a door front panel made Mark the two hinge holes and the by another manufacturer four smaller holes as shown in the diagram Preparing the front panel Depending on country this tumble Measure distance X for drilling the dryer is supplied either left or right hinge holes hand hinged with spacer bars For left hand hinging only front panel shown decor side face down upper edg
52. pped up when it is being moved It is therefore a good idea to run the Cool air programme for approximately 1 minute before moving it Any remaining condensed water will then be fed into the condensed water container or out through the drain hose 39 Installation Matching the fascia panel to the height of adjacent drawer fronts The fascia panel can be aligned with the drawer fronts by adjusting the spacer bars m Using a socket spanner turn clockwise or anti clockwise until the required height is reached If necessary individual bars can be removed or more added m To do this use the socket spanner to loosen the nuts An adapter kit with spacer bars and longer screws can be ordered as an optional accessory This can be used to add spacer bars from below up to a maximum of 25 mm After fitting the bars cut or pinch off any excess length from the screws 40 Removing the spacer bars All the spacer bars can be removed if the upper edge of the front panel needs to be flush with the upper edge of the appliance front directly underneath the fascia panel See Fitting a front panel made by another manufacturer m Open the door m Unscrew and remove the 3 screws see arrows m Remove all the spacer bars The 3 holes which are now free should be used to screw the front panel to the machine front later on Installation Fitting the front panel Fitting the fro
53. rammes Delay start You can select a programme and set it to start at a later time The programme will start automatically once the delay start time has elapsed Programmable functions Default settings can be altered to adapt the dryer to different requirements See Programmable functions at the end of this booklet for more details Perfect Dry indicator After a programme has started the electronics will estimate the duration of the programme time remaining The Perfect Dry indicator will flash while this is happening After a short while the programme duration will appear in the display and the indicator will go out The Perfect Dry indicator will light up again when the selected drying level is reached and remain on until the programme is finished Programme duration Estimated time remaining The estimated duration time remaining will appear in the display The following factors all affect the estimated time remaining residual moisture content after spinning type of fabric size of load room temperature fluctuations in power supply The electronics continually assess conditions in the appliance and adjust the estimated time remaining for a more accurate reading Because of this the time displayed can alter during the course of a programme Programmes can also finish earlier than expected if for example particularly fine fabrics are being dried the load is very small or items were part
54. revent small items from being trapped inside them Fasten hooks and eyes etc Tie fabric belts and apron strings Sew in or remove underwiring from bras Turn on the tumble dryer m Switch the dryer on by pressing the On Off I 8 button in The tumble dryer may be switched on after loading saving energy as the light will not come on Load the tumble dryer m Press the Door button to open the door m Load the laundry loosely into the drum Do not overload the drum See the Programme chart for recommended loads for each programme Overloading can cause unnecessary wear and tear to the laundry and give a disappointing drying result m Before closing the door make sure the fluff filter is correctly positioned Check the laundry is right inside the drum so that it cannot get trapped or damaged when the door is shut m Shut the door either with a gentle swing or lean against it and push it shut How to dry correctly Select a programme O Cottons Automatic plus O O Minimum iron Denim O Shirts O Timed drying cool air 9 Timed drying o warm air O Delicates Woollens handcare O Proofing O Express Gentle smoothing O m Select the programme you want The indicator for the programme selected will light up A drying level or extra option indicator may also light up and the duration may also be displayed Drying level programmes Cottons Minimum iron
55. rm air programme Select a different programme next time Items made of synthetic fibres are charged with static electricity after drying Synthetic fibres tend to attract static charge Static charge can be reduced by adding a fabric conditioner to the final rinse in the washing programme or a fabric conditioner sheet to the load when drying There is a build up of fluff Fluff is principally the result of friction when garments are being worn and to some extent when they are being washed Machine drying does not affect the lifetime of the fabric Fluff is collected by the fluff filters and can be removed easily see Cleaning and care You can alter the drying levels for some programmes see Programmable functions at the the end of this booklet 32 Problem solving guide Other problems Problem Possible cause Remedy The drying process goes on too long or even switches off In some circumstances the Clean out airways indicator light still comes on even though the filters are clean Please check all the possible causes and switch the dryer off and then back on again Ventilation to and from the dryer may be insufficient e g because it is installed in a room which is too small This can cause the temperature in the room to rise sharply Open a door or window while the dryer is in operation for increased a flow ir The v
56. rn valve supplied with the dryer must be fitted to prevent the risk of back flow See Installation conditions requiring a non return valve Maximum delivery head with non return valve fitted 1 00 m Arranging the drain hose N Do not pull on the drain hose and do not stretch it or allow it to become kinked as it could get damaged m Unclip the drain hose from clips 1 and 2 m Then pull it off connection 3 m The lower clip 4 can be opened to allow you to take the drain hose out or to feed the mains cable through it 45 Installation External drainage via a sink or gully m See Front view illustration If you want to drain the water off into a sink you will need to secure the hose carefully e g by tying it to a tap to make sure it cannot slip during use Otherwise there is a risk of overflowing water which could cause damage m Use the bow shaped guide to prevent the drain hose from becoming kinked see Front view illustration Installation conditions requiring a non return valve A If the on site water drainage system is not fitted with a non return valve or an appropriate air gap an air gap or the non return valve supplied with the machine must be fitted to prevent the risk of back flow Otherwise water could leak out of the dryer and cause damage A non return valve is required If the tumble dryer is connected to a sink drain outlet see the following sectio
57. rt Stop button switches between the options Switch the dryer off The setting you have selected is now stored in memory You can change it again at any time To check the setting m Carry out steps to m Switch the dryer off after step Programmable functions Standby To save energy the display and the programme sequence check lights go out after 10 minutes and the Start Stop button starts flashing slowly To come out of standby mode m Turn the programme selector or press a button Neither will have any effect if a programme is running On The standby function is activated and the display and programme sequence check lights will go out after 10 minutes if a programme is not selected after the dryer has been switched on after a programme has started They will however come on for 10 minutes after a delay start time has counted down at the end of the programme or the end of the anti crease phase The buzzer if selected will sound for 10 minutes at the end of the programme Factory default Not in current programme As described under On However the display and programme sequence check lights will stay on after the programme has started and remain visible during the programme Off The display and programme sequence check lights will stay on while the dryer is switched on Follow the steps 0 0 to programme and store in memory m See next page
58. s Hand iron and Machine iron Machine iron 63 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW Tel 0845 365 0555 Fax 0845 365 0777 Customer Contact Centre Tel 0845 365 6600 E mail info miele co uk Internet www miele co uk Australia Miele Australia Pty Ltd ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 03 9764 7130 Fax 03 9764 7149 Internet www miele com au China Miele Shanghai Suite 4105 06 Plaza 66 1266 Nanjing Road West Jing An District Shanghai 200040 PRC Tel 86 21 6288 4200 Fax 86 21 6288 4100 E mail mieleshanghai cn miele com Internet www miele cn Miele Hong Kong Limited 41 F 4101 Manhattan Place 23 Wang Tai Road Kowloon Bay Hong Kong Tel 852 2610 1331 Fax 852 2610 1013 Email mielehk miele com hk India Miele India Pvt Ltd Ground Floor Copia Corporate Suites Plot No 9 Jasola New Delhi 110025 Tel 011 46 900 000 Fax 011 46 900 001 E mail customercare miele in Internet www miele in Germany Miele amp Cie KG Carl Miele Stra e 29 33332 G tersloh Ireland Miele Ireland Ltd 2024 Bianconi Avenue Citywest Business Campus Dublin 24 Tel 01 461 07 10 Fax 01 461 07 97 E Mail info miele ie Internet www miele ie New Zealand Miele New Zealand Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland NZ Tel 0800 264 353 Fax 0800 463 453 Interne
59. t www miele co nz Singapore Miele Southeast Asia Miele Pte Ltd 163 Penang Road 04 02 03 Winsland House Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail infosea miele com sg nternet www miele sg South Africa Miele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 27 0 11 548 1900 Fax 27 0 11 548 1935 E mail info miele co za nternet www miele co za United Arab Emirates Miele Appliances Ltd P O Box 11 47 82 Gold amp Diamond Park Sheikh Zayed Road Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 971 4 341 88 52 E Mail info miele ae Internet www miele ae Alteration rights reserved 1010 ce M Nr 07 844 000 00
60. ters The fluff which is created by the drying process is collected by the fluff filters in the door and the door opening Clean the filters after each drying programme Cleaning them whilst dry Tip You can also use a vacuum cleaner to remove the fluff m Open the door and pull the fluff filter 1 out of the door as illustrated m Use your fingers to remove the fluff from the surface of the filter m Remove any fluff from the hollow part of the door opening You could also use a cleaning brush which is available as an optional extra from your Miele dealer or the Miele Spare Parts Department or use a vacuum cleaner Also clean the door seal 2 with a damp cloth Once clean push the filter back into the door holder until it clicks into position Ensure it is facing the correct way m Use your fingers or a vacuum cleaner to remove the fluff from the two fluff filters in the door opening m Close the door Always check the fluff filters if the Clean out airways indicator light comes on 23 Cleaning and care Cleaning them with water If there is a great deal of compacted fluff on any of the filters they can be removed and cleaned under hot running water m Open the door and pull the fluff filter out of the door as described previously The two filters in the door opening can also be removed if you need to clean them with water m Turn dial and pull the filter by t
61. thes as they have a tendency to shrink Low temperature Select the Low temperature option for delicate fabrics with the O symbol on the care label Hand iron Machine iron Fabric Cotton or linen fabrics e g Table linen bed linen starched laundry Note To prevent laundry from drying out it should be rolled up until you are ready for ironing Low temperature Select the Low temperature option for delicate fabrics with the symbol on the care label Minimum iron Max load 3 kg Normal Hand iron Fabric Minimum iron cotton synthetic and mixed fibre fabric e g tops dresses trousers skirts and table cloths Low temperature Select the Low temperature option for delicate fabrics with the O symbol on the care label Delicates Max load 2 kg Normal Hand iron Fabric Synthetic mixed fibre rayon and easy care cotton e g shirts blouses lingerie and appliqu d garments Low temperature Low temperature cannot be deselected Weight of dry laundry Note for test institutes Use this programme without selecting Low temperature for testing according to Standard EN 61121 Programme chart Woollens handcare Max load 2 kg Fabric Woollen fabrics Note This programme only fluffs up woollen garments They are not dried completely by this programme Remove garments as soon as the programme has f
62. tomatic plus indicator light will also flash once 2 Reduced residual moisture Laundry drier the Automatic plus indicator light will also flash twice Pressing the Start Stop button switches between the options Switch the dryer off The setting you have selected is now stored in memory You can change it again at any time To check the setting m Carry out steps to m Switch the dryer off after step 51 Programmable functions Altering the residual moisture level in the Minimum iron programme The tumble dryer is designed to dry effectively using as little energy as possible However if you require the laundry to be drier or damper you can reduce or increase the default residual moisture in the Minimum iron programme Follow the steps 0 0 6 to programme and store in memory Before you begin ensure that The tumble dryer is switched off The door is closed Press the Start Stop button and keep it pressed in whilst carrying out steps 8 0 Switch the dryer on Wait until the Start Stop button lights up constantly and then release the Start Stop button Press the Low temperature button once The Low temperature indicator light will flash twice briefly 52 A number to show which option is selected will appear in the display alternating with the letter P O Increased residual moisture Laundry damper Standard residu

Miele T 4819 Ci L

Contents

Download Pdf Manuals

Related Search

Related Contents