Home

Sanyo LNS-T02E

1. Fasten the lens motor lead at the A B C points with wire holder See figure 4 N Figure shown inside of the cabinet LENS MOTOR CONNECTOR K16B LENS MOTOR B This part wiring should not be tightened LENS MOTOR LEAD CONNECTOR K16B LENS MOUNTING BRACKET INSTALL THE LIGHT BLOCK SHEET LIGHT BLOCK SHEET See figure 6 Install the light block sheet around the lens as shown in the illustration Use the sheet included with the lens MOUNT THE LENS COVER See figure 7 When in install the both upper and lower lens UPPER LENS COVER covers put the light block sheet through the lens and install the sheet so that it should be placed in the guide slot of the lens cover See figure 8 If the installation of the light block sheet is incorrect there will be the space between lens and the lens cover so that it will be the cause of leakage of light or the dust entering at the main cabinet 1 Insert the upper part lens cover and fix them with screws A 4 screws 2 Insert the lower part lens cover and fix them with screws B 2 screws Set the
2. light block sheet so that the large rounder side is set over the lens Removed lens cover in figure 2 is not used keep the cover for possible re use when current lens is used Insert into the slot m 1 GHT BLOCK SHEET Fig 8
3. 3 Remove screws B 2 screws 4 Remove screws C 2 screws and remove upper lens cover In case figure 2 cabinet Remove 4 screws of the lens cover and remove the lens cover IN CASE OF MODEL WITHOUT LENS REMOVE THE COVER PLATE OF THE LENS COVER See figure 3 Remove 2 screws and pull down the plate ee ee At the step 5 insert the light block sheet in the same position as the removed cover plate has been placed Two screws are not used ia SCREWS Use the light block sheet included with lens Set the light block sheet so that the Fig 3 large rounder side COVER PLATE is set over the lens LIGHT BLOCK SHEET IN CASE OF MODEL WITH LENS REMOVE THE LENS See figure 4 Remove the connector K16B of the circuit board 2 Loosen the A B C wire holder and remove the lens motor lead 3 Remove screws D 4 screws which fastens the lens and remove the lens 3 JINSTALL THE LENS See figure 4 5 t Remove protective caps front and back on the lens Mount the lens at the lens mounting bracket with screws 4 screws included with the lens Use the driver included with the lens to fasten the screws After using save it for latter use See figure 5 3 Connect the lens motor lead to the connector K16B of the circuit board See figure 4 4
4. LCD PROJECTOR LENS MODEL NO LNS W02 T02 LNS W02K T02K Series LENS REPLACEMENT AND INSTALLATION PROCEDURE NOTES ON LENS INSTALLATION Lens installation should be performed by the qualified service personnel It should be followed by this procedure precisely Before attempt to install the lens confirm the model number both the LCD projector and the lens and use the proper lens If you have any questions contact to the dealers PARTS LIST Following parts are contained in the packing LENS 1 piece LENS MOUNTING SCREWS 6 screws 2 for spare DRIVER 1 piece LIGHT BLOCK SHEET 1 sheet LENS COVER UPPER LOWER 1 set Following checks and confirmations should be taken for safety Check the following things by the time of the cabinet assembly after the lens installation 1 Confirm the lens is securely fixed by 4 screws 2 Wiring must not be tangled in the gear of the lens motor or the other mechanical part 3 There is no missing part or no loosing mounting part 1AA6P1P2289 ICSC LENS REPLACEMENT AND INSTALLATION PROCEDURE Perform the steps 1 to 5 for lens replacement and installation First set the lens at the center position with lens shift button UPPER LENS COVER C REMOVE THE LENS COVER First check the shape of cabinet In case figure 1 cabinet 1 Remove screws A 2 screws 2 Pull down the lower lens cover while pushing the part D then remove it

Sanyo LNS-T02E

Contents

Download Pdf Manuals

Related Search

Related Contents