TFA 42.4001 sport watch
Contents
1. fiii HIKE Cat No 42 4001 Instruction Manual INTRODUCTION This device is a digital product that provides altimeter barometer compass altimeter data dual time chronograph chronograph data and alarm functions Features Altimeter 1 meter or foot resolution and with working range from 700 meters 2296 feet to 9000 meters 29520 feet Graphical expression of changes provided Unit in meters or feet selectable 20 memories with date time and altitude reading Barometer 1 hPa resolution and with working range from 300 hpa to 1100 hpa Graphical expression of changes provided Both sea level pressure and absolute pressure can be shown Weather forecast Temperature displayed in F or C selectable Compass Electronic compass providing 16 cardinal indications together with bearing in degrees Declination correction provided Time 2 time modes selectable Presents day of the week day hours minutes and seconds year and month can also be set 12 24 hour formats selectable Auto calendar from 2000 to 2049 Chronograph 1 100 second resolution with working range up to 24 hours 100 memories for lap split times stored in a maximum of 30 runs Alarm 2 daily alarms Hourly chime Electro luminescent backlight 3 seconds light up EL backlight Altimetermode with altitude change measures every 2 5 seconds Altimetermode without altitude change barometer2. 1 The compass should be calibrated before use 2 The compass must be kept in a level position when in use 3 Compass readings are easily affected by disturbing sources of magnetism so the compass should always be used in the open air To calibrate the compass 1 Hold down D until CAL is shown on the display which indicates the calibration screen 2 Rotate the product clockwise slowly for 2 complete rotations Each rotation must last for at least 15 seconds Keep the watch in a level position when calibrating Do avoid close contact to metal parts or other electrical instruments when calibrating 3 Press D and the ten degree digit starts to flash on the display which indicates the declination angle setting screen Press A will end calibration skipping the declination angle setting In this case the declination angle is set to 0 degree 4 Use A and B to change the setting Holding down either button scrolls the setting at high speed 5 Press C to advance to the next setting as in the following TENS OF DEGREE ae DEGREE 2 E W When E or W is flashing press A or B to switch between East and West You should consult your local organization for information of declination Declination angles for major cities are listed below for reference only 6 Press D to end calibration If ERR indicating error is displayed calibrate the compass again If there is no button operation for 2 3 minutes during calibr
3. C HOUR gt MINUTE gt SECOND gt YEAR c 4 C c lt C 12 244 lt DAY lt MONTH When second digits are flashing press A or B to reset the digits to 00 Resetting seconds when the digits are between 00 to 29 will leave the minute digits unchanged or between 30 to 59 will increase the minute digits by one When 12 or 24 is flashing press A or B to switch between 12 or 24 hour formats If 12 hour format is chosen AM or PM indicator will be shown 4 Press D to exit the setting screen and day of the week will be adjusted automatically If there is no button operation for 2 3 minutes at setting screen the display will return to Time mode automatically COMPASS MODE Cardinal indicator South indicator North indicator D Bearing E Hold D Compass mode indicator CALIBRATION SCREEN Use C to enter Compass mode Mode prompt COMP is displayed first and bearings will be taken automatically Compass mode indicator is shown When you take bearings readings are shown in 16 cardinal indications together with bearing in degrees Reading shown indicates the direction that the LCD s 12 o clock position is pointing to North South arrow is shown on circumference of the LCD North is indicated by 1 flag and South is indicated by 3 flags Declination correction is provided Declination is the difference between true north and magnetic north Importance
4. indicator Chime on indicator Alarm on indicator Use C to enter Alarm mode Mode prompt ALRM is displayed first There are 2 daily alarms and they can be set to refer to Normal Time indicated by T1 or Dual Time indicated by T2 Daily alarm sounds at the same time each day while it is turned on The alarm sounds at the preset time for about 20 seconds or until you stop it by pressing any button The alarm on indicator is only displayed at the time mode that the alarm is set to refer to Hourly chime sounds at every full hour while it is turned on If chime is turned on confirmation sound will be given whenever a button is pressed To switch between alarm 1 and alarm 2 Press B to switch between alarm 1 indicated by AL 1 and alarm 2 indicated by AL 2 To set alarm time and turn chime on and off 1 Hold down D until the hour digits start to flash on the display which indicates the setting screen 2 Use A and B to change the setting Holding down either button scrolls the setting at high speed 11 3 Press C to advance to the next setting as in the following C C C C HOUR gt MINUTE gt REFERTO T172 gt CHIME ON OFF When TIME 1 or TIME 2 is flashing press A or B to switch between setting the alarm to refer to Normal Time TIME 1 and Dual Time TIME 2 When ON or OFF is flashing press A or B to turn the chime on indicated by ON and off indicated by OF
5. mode every 2 5 minutes Barometermode measures every 2 5 minutes Changes to Time mode after 24 hours Temperature measures every 2 5 minutes BASIC OPERATION OF BUTTONS A SWITCH AMONG DISPLAYS TAKE BEARING STORE ALTITUDE DATA PRESS AND HOLD FORWARD SELECTION OF ALTITUDE DATA START LAP OF CHRONOGRAPH RETRIEVE DATA IN RUN TURN ALARM ON AND OFF FORWARD SETTING SET OR CALIBRATION B SWITCH BETWEEN NORMAL TIME AND DUAL TIME PRESS AND HOLD SWITCH BETWEEN UNITS OF TEMPERATURE PRESS AND HOLD SWITCH BETWEEN UNITS OF ALTITUDE PRESS AND HOLD REVERSE SELECTION OF ALTITUDE DATA STOP CHRONOGRAPH STORE CHRONOGRAPH DATA PRESS AND HOLD SELECT RUN NUMBER SWITCH BETWEEN ALARM 1 AND ALARM 2 REVERSE SETTING SET OR CALIBRATION C MODE CHANGE DIRECT CHANGE TO TIME MODE PRESS AND HOLD ADVANCE TO NEXT SETTING SET OR CALIBRATION D EL BACKLIGHT ENTER SET OR CALIBRATION PRESS AND HOLD CLEAR DATA PRESS AND HOLD EXIT SET OR CALIBRATION EL BACKLIGHT Press E for EL backlight with 3 seconds auto light up MODE CHANGE OPERATION There are 9 modes Normal Time Dual Time Compass Barometer Altimeter Altimeter Data Chronograph Chronograph Data and Alarm Press C to change from mode to mode hold down B to switch between Normal Time mode and Dual Time mode as in the following Hold B NORMAL TIME lt a gt DUAL TIME C COMPASS 4 C BAROMETER C ALTIMETER C 4
6. shows hours minutes and seconds Leading zeros will not be shown There are 100 memories for lap split times stored in a maximum of 30 runs The chronograph lets you measure elapsed time lap split times and two or more finishes When you take lap split times the display will be frozen to show lap time split time and lap number for about 6 seconds then the display will show the current running times automatically To measure elapsed time 1 Press A to start the chronograph 2 Press B to stop the chronograph You can resume the measurement operation by pressing A 3 Hold down B until the next run number is shown on the display Data of the current run is stored and chronograph is reset to all zeros To measure lap split times 1 Press A to start a time measurement 2 Press A again when you want to take the first lap split time 3 Press A again when you want to take the next lap split time You may take up to 100 lap split times by pressing A 4 Press B to stop the time measurement 5 Hold down B until the next run number is shown on the display Data of the current run is stored and chronograph is reset to all zeros To measure two or more finishes 1 Press A to start a time measurement 2 Press A again when the first runner finishes 3 Press A again when the second runner finishes You may record the finish time of up to 100 runners by pressing A 4 Press B when the last runner finishes Time measurem
7. B to change the setting as in the following 3 Press D to exit the setting screen If there is no button operation for 2 3 minutes at setting screen the display will return to Barometer mode automatically Unit indicator Altitude graph Of altitude ALTIMETER MODE Current Altitude reading Time Altimeter mode indicator Use C to enter Altimeter mode Mode prompt ALTI is displayed first Altimeter mode indicator is shown The altimeter is of 1 meter or foot resolution and with working range from 700 meters 2296 feet to 9000 meters 29520 feet Altitude reading in meters or feet selectable Graph showing the changes in altitude is provided Graph will be cleared only after battery replacement or reset Maximum 20 altitude data can be stored Reading the altitude graph The altitude graph shows the relative changes in altitude in the past with the current altitude represented on the right Each horizontal point represents 15 minutes while each column represents the relative reading of altitude in that time It is not possible to get the exact reading from the graph User can only get the trend of changes from the graph To switch between meters and feet Hold down B until the unit indicator M or Ft stops flashing to switch altitude reading between meters and feet To store altitude data Hold down A until DATA stops flashing to store the current altitude data STORED an
8. C ALTIMETER DATA C CHRONOGRAPH 4 C CHRONOGRAPH DATA J C ALARM At any mode holding down C will change to Time mode directly TIME MODE Normal Time indicator Dual Time indicator she AM oes th A indicator PM ee Pee indicator oe eae Use C to enter Time mode Mode prompt TIME is displayed first There are 2 time modes Normal Time indicated by T1 and Dual Time indicated by T2 and they count up individually with the same second There are 3 displays for time They are Time Time with Barometer and Time with Weather There is an auto calendar from 2000 to 2049 To switch between Normal Time and Dual Time Hold down B until the mode indicator T1 or T2 stops flashing to switch between Normal Time mode and Dual Time mode To switch among the 3 time displays Use A to switch among the 3 displays for time TIME BAROMETER or WEATHER is displayed first Graph of Weather indicators Day of the week Day sea level pressure Current sea level pressure Unit indicator of temperature TIME TIME BAROMETER TIME WEATHER A Graph of sea level pressure is described in BAROMETER MODE To set time 1 Hold down D until the hour digits start to flash on the display which indicates the setting screen 2 Use A and B to change the setting Holding down either button scrolls the setting at high speed 3 Press C to advance to the next setting as in the following C C
9. F If chime is turned on the chime on indicator will be shown after exiting setting screen 4 Press D to exit the setting screen The alarm turns on which is indicated by ON and the appearance of the alarm on indicator If there is no button operation for 2 3 minutes at setting screen the display will return to Alarm mode automatically To turn the alarm on and off Press A to turn the alarm on indicated by ON and off indicated by OFF If the alarm is turned on the alarm on indicator will be shown RESETTING THE PRODUCT Hold down A B C and D simultaneously all segments will be on then release the buttons and the product will be reset After reset there will not be any measurement of altitude pressure or temperature until A or C is pressed After reset entering Compass mode will change to calibration screen directly BATTERY REPLACEMENT Replace the exhausted battery with a CR2032 cell or equivalent Please contact a specialized dealer for battery change Thereby the sealing ring must not be damaged No guarantee if the instrument is handled or opened improperly Attention Do not dispose of empty batteries in household waste Take them to special local collection sites CE 12
10. ation or at declination angle setting screen the display will return to Compass mode automatically To take bearings 1 Press A bearings will be taken and shown for about 10 seconds If no bearing is being taken the display shows 2 Hold down A bearings will be taken and shown continuously and for 10 seconds more after A is released BAROMETER MODE TE Graph of Sea level pressure Weather indicator Current Sea level pressure Unit indicator Barometer mode indicator Of pressure Barometer mode indicator Use C to enter Barometer mode Mode prompt BARO is displayed first Barometer mode indicator is shown The barometer is of 1 hPa resolution and with working range from 300 hpa to 1100 hpa Both sea level pressure and absolute pressure can be shown Graph showing the changes in sea level pressure is provided Graph will be cleared only after battery replacement or reset Weather forecast indicated by the weather indicators for the coming 24 48 hours is provided Forecast is accurate only if the barometer has been functioning for at least 12 hours Temperature is of 0 1 degree resolution and with working range from 4 F 20 C to 158 F 70 C And unit in F or C selectable There are 3 displays for Barometer mode To switch among the 3 displays for barometer mode Use A to switch among the 3 displays for barometer mode gt gt PM a indicator T
11. d data number are shown To calibrate altitude reading 1 Hold down D until the current altitude reading starts to flash on the display which indicates the setting screen 2 Use A and B to change the setting Holding down either button scrolls the setting at high speed 3 Press D to exit the setting screen If there is no button operation for 2 3 minutes at setting screen the display will return to Altimeter mode automatically ALTIMETER DATA MODE Data number 3 seconds Time Month Day Altitude reading Use C to enter Altimeter Data mode Mode prompt ALTI DATA is displayed first Data number time date and altitude reading can be retrieved Altitude data are shown in 2 different displays To retrieve the altitude data Use A and B to select the altitude data to be retrieved To clear the altitude data Hold down D until is shown on the display to clear all altitude data stored Altitude data cannot be cleared individually CHRONOGRAPH MODE Lap time indicator Lap time Split time Lap number Split time indicator Use C to enter Chronograph mode Mode prompt CHRO is displayed first The chronograph is of 1 100 second resolution for the first hour and 1 second resolution for the rest and with working range up to 24 hours then the chronograph stops automatically For the first hour the chronograph shows minutes seconds and 1 100 seconds then it
12. emperature Absolute pressure Time Reading the graph of sea level pressure The graph shows the relative changes in sea level pressure in the past with the current pressure represented on the right Each horizontal point represents one hour while each vertical point represents the relative reading of pressure in that time It is not possible to get the exact reading from the graph User can only get the trend of changes from the graph To switch between F and C 1 Use A to switch to the barometer display with temperature 2 Hold down B until the unit indicator F or C stops flashing to switch temperature between F and C To set sea level pressure reading 1 Hold down D until SET CURRENT WEATHER scrolls on the display which indicates the weather setting screen The weather indicators start to flash 2 Press C SET SEA LEVEL PRESSURE scrolls on the display which indicates reading setting screen The current sea level pressure reading starts to flash 3 Use A and B to change the setting Holding down either button scrolls the setting at high speed 4 Press D to exit the setting screen If there is no button operation for 2 3 minutes at setting screen the display will return to Barometer mode automatically To set current weather 1 Hold down D until SET CURRENT WEATHER scrolls on the display which indicates the weather setting screen The weather indicators start to flash 2 Use A and
13. ent is stopped 5 Hold down B until the next run number is shown on the display Data of the current run is stored and chronograph is reset to all zeros The finish times for the runners are the split times stored in Chronograph Data mode To clear times in current run 1 Press B to stop the chronograph 2 Hold down D until the chronograph shows all zeros Times in current run are cleared CHRONOGRAPH DATA MODE Lap time Run number indicator Lap time 2 seconds Split time Lap number Month Day Split time indicator Use C to enter Chronograph Data mode Mode prompt CHRO DATA is displayed first Run number date lap split time of each lap best lap time and average lap time can be retrieved If chronograph is running chronograph data cannot be cleared To retrieve the chronograph data 1 Use B to select the run to be retrieved Run number and date are shown for about 2 seconds first 10 2 Press A to retrieve the data one by one Display examples Lap number Lap split time of lap 1 Best lap time Average lap time To clear one particular run 1 Use B to select the run to be cleared 2 Hold down D until CLEAR HOLD ALL is shown on the display release D and the selected run will be cleared To clear all runs Hold down D until is shown on the display All runs are cleared ALARM MODE 0 Alarm 1 indicator T1 indicator Alarm time ON OFF status
Download Pdf Manuals
Related Search