Silverstone SST-ST60F-P power supply unit
Contents
1. factor less than 110 for the critical components is recommended before the power supply is shut down Temperature derating factors higher than 110 can be evaluated on a case by case basis 4 TIMING 4 1 Signal timing drawing Figure 2 is a reference for signal timing for main power connector signals and rails 12VA45V 4 3 3V 0 P PW OK PW OK Sense level 95 of nominal rn melee cite 22 4 F a Figure 2 PS OK Timing Sequence 1 T2 Rise time 0 1ms 20ms 2 T3 Power good turn on delay time 100ms 500ms 3 T4 Power good turn off delay time 1ms min 4 T5 Rise time 10ms max STRIDER PLUS SERIES A 4 2 Output Transient Response Table 13 summarizes the expected output transient step sizes for each output The transient load slew rate is 1 0A us Table 13 DC Output Transient Step Sizes of rated output amps per Sec 3 2 3 1 5 VDC 30 3 3 VDC 30 For example for a rated 5 VDC output of 18A the transient step would be 30 x 18A 5 4A Output voltages should remin within the remain within the regulation limits of Section 2 1 and the power supply should stable when subjected to load transients per Table 13 from any steady state load including any or all of the following conditions Simultaneous load steps on the 12 VDC 5 VDC and 3 3 VDC outputs all steps occurring in the same direction Load changing repetition rate of 50 Hz to 10 kHz AC in2. OM 19 7 COM Black White N C 20 8 PWRGOOD Grey Red 5VDC 21 9 5Vsb Purple is OEA N 12V Yellow Red 5Vsense 22 Red 5VDC 23 11 12V Yellow Black COM 24 12 3 3V Orange EPS 12V 8PIN Connector Signal Pin Pin an Yellow 12V Black eto vf ef oou f aaa Yellow 12V COM Black Yellow 2 a 4 com Black ATX 12V 4PIN 4 4PIN EPS 12V in split mode CT senate frm Set e o fao w fo w Black 12V Yellow N STRIDER PLUS SERIES AE 4PIN peripheral connector HDD 4PIN floppy connector FDD Yellow Black Black Black Black Red Yellow SATA connector sara Orange 3 3V Yellow 12V 1 8PIN PCI Express connector Signal Pin Pin Signal Yellow 12V 1 5 COM Black Yellow ax 2 6 co Black Yellow 12V 3 if COM Black ie Black sense1 COM 4 8 COM Black To be valid this sheet must be filled out by your salesperson at the time of purchase Store 6PIN PCI Express connector Purchaser Purchase date Swa Pin Pin so ae Serial No ator seve e cow eax
3. SILVER STONE Designing Inspiration STRIDER PLUS SERIES ST60F P SilverStone Technology Co Ltd 600W 24hour continuous power output with 40 C operating temperature www silverstonetek com 100 modular cables Efficiency 85 88 at 20 100 loading support silverstonetek com Class leading single 12V rail with 42A Issue date March 2010 Strict 3 voltage regulation NO G1121 Japanese main capacitors Silent running 135mm fan with 19dBA minimum Dual EPS 8pin connectors support Single PCI E 8pin and four PCI E 6pin connectors support Support ATX 12V 2 3 amp EPS 12V Active PFC aah STRIDER PLUS SERIES A SPECIFICATION SilverStone Strider Plus ST60F P ATX12V EPS 12V Switching Power Supply With Active PFC PS 2 This specification describes the requirements of ST60F P with active P F C Switching Power Supply with an ATX form factor 5V standby voltage fan control ATX 12V Power supply version 2 3 remote on off control dual line input capability and forced air cooling characteristics 1 Table1 1 AC INPUT requirements The input voltage current and frequency requirements for continuous operation are stated below lin 10 5 A 1 1 Inrush current limiting 50 A 115Vrms 100 A 230Vrms at 25 C ambient cold start 2 DC OUTPUT 2 1 Table 2 DC voltage regulation 2 2 Load Ranges 2 2 1 Table 3 Typical Power Distribution for a 600W ATX12V Configuration Cross L
4. at nominal input voltage of 115VAC or 230VAC 2 6 Remote on off control When the logic level PS ON is low the DC outputs are to be enabled When the logic level is high or open collector the DC outputs are to be disabled 3 PROTECTION 3 1 Over power protection The power supply will be shutdown and latch off when output power is 110 160 3 2 Over voltage protection The over voltage sense circuitry and reference shall reside in packages that are separate and distinct from the regulator control circuity and reference No single point fault shall be able to cause a sustained over voltage condition on any or all outputs The supply shall provide latch mode over voltage protection as defined in Table 12 VDC 5 VDC 3 3 VDC Volts Volts J 3 3 Over Current Protection 5VDC and 3 3VDC have separate over current protection circuits to meet 240VA safety requirement 12V 50 65 A No damage or hazardous condition should occur with all the DC output connectors disconnected from the load The power supply may latch into the shutdown state 3 4 Over Current Protection In the event of a fan failure or the vents being blocked the power supply shall have protection such that any over temperature condition caused by these events shall protect the power supply from damage or abnormal and or dangerous operation A shutdown of the power supply is acceptable A temperature derating
5. oading graph for 600w Configuraton 5V 3 3V power W 250 300 350 400 450 500 550 600 12V power W Parameter Mn A aw o e aa i Le re a er a o fo Caves oo ies os are N STRIDER PLUS SERIES A Note 1 Total combined output of 3 3V and 5V is lt 140W 2 12V outputs power shall not exceed 504W 3 When 5V load is 24A 12V min load is 38A 4 When 12V load is 42A 5V min load is 5A 5 Peak currents may last up to 17 seconds with not more than one occurrence per minute requirements 2 3 DC Output Ripple Noise 2 3 1 Table5 Ripple regulation Ripple Noise 2 3 2 Definition The ripple voltage of the outputs shall be measured at the pins of the output connector when terminated in the load impedance specified in figure 1 Ripple and noise are measured at the connectors with a 0 1uF ceramic capacitor and a 10uF electrolytic capacitor to simulate system loading Ripple shall be measured under any condition of line voltage output load line frequency operation temperature 2 3 3 Fignre1 Ripple Noise voltage test circuit o T Figure 1 Ripple Noise voltage test circuit 2 4 Overshoot Any overshoot at turn on or turn off shall be less 10 of the nominal voltage value all outputs shall be within the regulation limit of section 2 0 before issuing the power good signal of section 5 0 2 5 Efficiency Power supply typical efficiency is 82 under full Load
6. put range per Section 1 0 5vsb Loading min 0 1A 4 3 Hold up time T6 of figure 2 When the power loss its input power The output shall maintain 10ms in regulation ranges at nominal input voltage AC 115V 60Hz or 230V 50Hz 90 load 4 4 Capacitive Load REQUIRED The power supply should be able to power up and operate with the regulation limits defined in Table With the following capacitances simultaneously present on the DC outputs Output Capacitive Loads 12VDC 10000 5 VSB 6000 5 ENVIRONMENT 5 1 Operation 5 2 Shipping and Storage Relative Humidity 20 to 85 non condensing Relative Humidity 5 to 90 non condensing 5 3 Altitude 5 4 Operating AC Input lela Storage 15 000FT max 6 MTBF 6 1 MTBF MEAN TIME BETWEEN FAILURES CALCULATION The demonstrated MTBF shall be 100 000 hours of continuous operation at 25 C full load 80 confidence limit and nominal line The MTBF of the power supply shall be calculated in accordance with MIL STD 217D E The DC FAN is not included 7 MECHANICAL REQUIREMENTS 7 1 Physical Dimension 150 mm W x 86 mm H x 160mm D STRIDER PLUS SERIES J 7 2 Connectors M B 24PIN connector Signal Pin Pin Signal N Orange 3 3V 13 i BAN Bares Orange 3 3Vsense 13 Blue 12VDC 14 2 3 3V Orange Black COM 15 3 COM Black Green PS ON 16 4 5VDC Red Black COM 17 5 COM Black Black COM 18 6 5VDC Red Black C
Download Pdf Manuals
Related Search