Miele DA 289-4
Contents
1. NThe overall ventilation condition of the dwelling must be taken into account If in any doubt the advice of a competent builder or for gas a qualified gas fitter registered with an official gas safety body in accordance with national safety regulations GasSafe in the UK must be sought components with the cooker hood see Operation with Control module DSM 400 It is available to purchase as an optional extra If in any doubt the advice of a competent builder or for gas a qualified gas fitter GasSafe registered in the UK must be sought If the hood is being operated in recirculation mode the above restrictions do not apply Warning and safety instructions Correct use P Never use an open flame beneath the cooker hood To avoid the danger of fire do not flamb or grill over an open flame When switched on the cooker hood could draw flames into the filter Fat particles drawn into the cooker hood present a fire hazard P When using the cooker hood over a gas hob ensure that any burners in use are always covered by a pan Switch the cooking zone off when a pan is removed even for a short time Regulate the flame so that it does not burn up the sides of the pan Do not allow the pans to overheat excessively e g when using a wok The cooker hood can become damaged when exposed to excessive heat P Always switch the cooker hood on when a cooking zone is in use otherwise condensation m2. The indicator lamp will come on If the cooker hood has been connected to a window contact switch via a Miele DSM 400 control module then the fan cannot be switched on if the window is shut The indicator lamp will flash To select a power level 0000 m Use the controls to select the power level required control control higher setting lower setting Depending on the intensity of the cooking vapours levels I to III are usually sufficient for normal cooking Intensive setting For short periods of cooking food with intensive vapours and a strong aroma e g when searing meat you may wish to select the Intensive Setting IV Automatic switch off of the Intensive setting You can set the Intensive setting so that it only runs for 10 minutes before reverting automatically to level Ill m To set this option both the fan and the hob lighting must be switched off m Press the run on option control for approx 10 seconds The first fan power setting indicator will light up m hen press in turn the hob lighting control __ 000 the control and finally the hob lighting control again Operation _ 0000 The indicator lamps for fan power levels and IV will flash if the automatic switch off for the Intensive setting is not activated m Press the control to activate automatic switch off The indicator lights for fan power levels a
3. For information about using the appliance see Operation Miele home Con ctivity dai2385 This cooker hood is communication enabled Communication module XKM 2000 DA CD available as an optional extra enables the operation of the cooker hood to be automatically controlled by the operating status of a Miele electric hob with onset controls For communication to take place the hob must be fitted with the appropriate communication module The hob transmits information about its operating status to the cooker hood via the household power supply Powerline 14 When the hob is switched on the cooker hood lights and the fan also comes on During cooking the cooker hood automatically sets its power level according to the number of cooking zones in operation and their power levels After switching the hob off the fan and the hob lighting will switch off automatically after a period of time For detailed information about this function please read the separate instruction booklet supplied with the XKM 2000 DA communication module The communication module is fitted to the cooker hood in the area of the motor and is connected to the controls of the cooker hood This module must be installed by a Miele service technician or suitably qualified electrician Operation To switch the fan on m Press the On Off control The fan runs at power level Il
4. additional means of disconnection must be provided for all poles For extra safety it is advisable to protect the appliance with a suitable residual current device RCD Contact a qualified electrician for advice Important This appliance is supplied for connection to an a c 230 V single phase 50 Hz supply The wires in the mains lead are coloured in accordance with the following code Green yellow earth Blue neutral Brown live WARNING THIS APPLIANCE MUST BE EARTHED Connection of this appliance should be made via a suitable isolator or a double pole fused spur connection unit which complies with national and local safety regulations and the On Off switch should be easily accessible after the appliance has been built in When switched off there must be an all pole contact gap of 3 mm in the switch including switch fuses and relays according to EN 60335 34 Operation with Control module DSM 400 The Miele DSM 400 Control module can be used to combine the cooker hood with other components It enables the following Connection to a window contact switch If adequate ventilation to the room can only be ensured by having a window open when the cooker hood is in use at the same time as a heating appliance which depends on the air from the same room then the control module can be used to connect a window contact switch not supplied to the appliance Once connnected the cooker hood can only
5. into the room when the cooker hood and the heater are in operation simultaneously an underpressure in the room of 0 04 mbar 4 pa is the maximum permissible dai1477 Ventilation can be maintained by air inlets which cannot be blocked in windows doors and outside wall vents One of the following technical measures may be necessary to ensure safe operation f the only way of ensuring adequate ventilation is via an open window a window contact switch should be fitted to ensure that the cooker hood can only operate when the window is opened sufficiently A window contact switch kit is available from good builders merchants Take care when ventilating the room through an open window that ventilation is not impaired by a closed blind or curtain The cooker hood can be set up to automatically switch on an air intake fan or open a motorised inlet flap when it is switched on The cooker hood can be set up to automatically switch off a heating appliance which also depends on the air from the room when it is or by other technical measures such as ensuring that the cooker hood can only be switched on when the heating appliance is switched off or vice versa switched on The Miele DSM 400 control module offers the possibility of combining other A ventilation brick alone is not generally sufficient to ensure safe ventilation
6. old data Operation If the indicator lamp for the grease filter control turns blue during operation this indicates that unrequired electronics have been activated inadvertently To deactivate With the fan switched off press the control and the grease filter control at the same time The filter operating hours indicator lamp will light up blue and one of the indicator lamps for the controls will flash Press the control repeatedly until the 4th indicator lamp for the controls lights up Confirm the procedure by pressing the grease filter control All the indicator lamps will go out 20 Cleaning and care Before carrying out any cleaning or maintenance work disconnect the cooker hood from the mains supply Ensure that itis switched off at the wall socket and the plug withdrawn or the fuse is withdrawn from the fused spur connection unit or the mains fuse is disconnected or the screw out fuse is removed in countries where this is applicable Miele branded cleaning and conditioning agents are available to order through your Miele Dealer Chartered Agent the Miele Spare Parts Department or via the internet on www miele shop com Housing General notes The surfaces and controls are susceptible to scratches and abrasions Please observe the following cleaning instructions m All external surfaces and controls can be cleaned
7. the tower en TE Installation instructions 29 Installation Before installation it is important to read the information given on the following pages as well as the Appliance dimensions and the Warning and Safety instructions at the beginning of this book This is particularly crucial when using the cooker hood at the same time as a heating appliance that relies on air from the same room as this could result in the build up of toxic fumes Installation instructions See enclosed Installation sheet for instructions on how to install this appliance Protective foil on stainless steel appliances The housing components have a protective foil to prevent them being damaged during transport m Please remove the protective foil before fitting the housing components It can be peeled off easily 30 Dismantling Should the appliance ever need to be dismantled follow the installation instructions in reverse order as described on the installation sheet A lever is supplied to assist with the removal of the tower dai0920 m After loosening the fixing screws on the tower push the lever between the tower and the extension piece to lever the tower out of its fixings Connection for air extraction Important To avoid the danger of toxic fumes please observe the Warning and Safety instructions This is especially crucial when using the cooker hood at the same time as another heatin
8. using a Miele E Cloth or with warm water and a little washing up liquid applied with a well wrung out soft sponge or cloth m Wipe the surfaces dry using a soft cloth Do not use too much water when cleaning the controls Water could penetrate into the electronics and cause damage Do not use cleaning agents containing soda acids chlorides or solvents abrasive cleaning agents e g powder cleaners or cream cleaners and abrasive sponges e g pot scourers or sponges which have been previously used with abrasive cleaning agents These will damage the surface material Important for appliances with stainless steel housing This infomation does not apply to the controls Stainless steel surfaces can be cleaned using the Miele E Cloth or with a proprietary non abrasive cleaning agent designed specifically for use on stainless steel To help prevent re soiling a proprietary conditioning agent for stainless steel can also be used Follow the manufacturer s instructions and apply sparingly with an even pressure in the direction of the grain Important for appliances with lacquered housing special order finish It is very difficult to clean this type of surface without causing minor marks to the surface material This can become particularly noticeable with darker colours and if there is halogen lighting in the kitchen 21 Cleaning and care Controls The controls may suffer discoloura
9. Miele Operating and installation instructions Cooker hood DA 289 4 DA 289 4 EXT To avoid the risk of accidents en GB AU NZ or damage to this appliance it is essential to read these instructions before it is installed and used for the first time M Nr 07 782 070 Contents Caring for the environment 00 liii i ie ess 4 Warning and safety instructions lll lessen 5 Modes of operation 1 0 0 0 0 eee 11 Guide to the appliance 0 2c eee 12 Mieleghome 0 00 93 ee 14 een CEPR 14 Operation du 5556 bead VRBES APR Latte 15 Toswitch the dati on sorer etc nte atat e e oen do m s bae RO a deles 15 TO Selecta POWSrleVel joao a iuto ex dtd RD ee P c e pate 15 RUN ZONHOPHON s uem AIRE ce eu eod Rote br noh inea ec p deca oko ede RR eta 16 TO SWIEChthiedal Olten hed atin a Dee 16 To switch the hob lighting On u urn te e tme 17 To dimithe hob lighting sae Pe e bebe bbe 17 To switch the hob lighting off 2 2 2 0 0 00 eee 17 Filter operating hours counter 0 eee 18 Reading the filter operating hours counter 0 0 iliis 18 To alter the filter operating hours counter o aasa aasa aea 19 Cleaning and care 00 0 e 21 mienne IT 21 Vapour plate and grease filter 2i iiis 22 Changing a halogen lamp 24 After Sales Service li i i eh 25 Appliance dimensions ill illl i
10. ay collect in the hood which could cause corrosion P When cooking with oil or fat chip pans and deep fat fryers etc do not leave the pans unattended Never leave an open grill unattended when grilling Overheated oil and fat can ignite and could set the cooker hood on fire P Do not use the cooker hood without the filters in place This way you will avoid the risk of grease and dirt getting into the appliance and hindering its smooth operation P The filters should be regularly cleaned or changed as appropriate Saturated filters are a fire hazard See Cleaning and care P The cooker hood can get very hot during cooking due to heat rising from the hob Do not touch the housing or the grease filters until the cooker hood has cooled down P Do not use a steam cleaner to clean this appliance Steam could reach the electrical components and cause a short circuit Warning and safety instructions Correct installation Accessories P Refer to the cooker or hob P Only use genuine Miele original manufacturer s instructions as to spare parts and accessories with this whether a cooker hood may be appliance If spare parts or accessories operated above the cooker hob from other manufacturers are used this will invalidate the guarantee and Miele gt The minimum safety distances cann tacopi habui between the top of the cooker or hob and the bottom of the cooker hood given in the Appliance dimensions
11. be operated when the window is sufficiently open see also Warning and Safety instructions When the window is closed the cooker hood fan cannot be switched on The indicator lamp for the On Off touch control on the cooker hood will flash The same applies to operation with an external motor depending on model The cooker hood lighting is not affected by this Take care when ventilating the room through an open window that ventilation is not impaired by a closed blind or curtain If the control module is disconnected in order to operate the cooker hood without the window contact switch e g after moving house the cooker hood electronics must be reset by a Miele service technician Potential free connection This enables an external appliance to be controlled according to the switch setting on the cooker hood fan For instance it can be used to ensure a sufficient supply of fresh air when the cooker hood and a heating appliance which also depends on the air in the room are being used together by switching on an air intake fan or opening a motorised inlet flap as soon as the cooker hood fan is switched on It is important to ensure that the fan power is sufficient and that the air intake has a suitable cross sectional diameter If a sufficient air intake cannot be guaranteed then the potential free contact will enable a heating appliance which depends on air in the same room as a cooker hood to be sw
12. ccessory is recommended dai2538 lf the exhaust air is to be ducted into a vent flue the ducting must be directed in the flow direction of the flue Important If the exhaust ducting is to run through rooms ceiling space etc where there may be great variations in temperature between the different areas the problem of condensation will need to be addressed The exhaust ducting will need to be suitably insulated 32 Condensate trap optional accessory dai1585 In addition to insulating the exhaust ducting we recommend that a suitable condensate trap is also installed to collect and evaporate any condensate which may occur Condensate traps are available for 125 mm or 150 mm ducting When installing a condensate trap ensure that it is positioned vertically and if possible directly above the exhaust connection The arrow on the housing indicates the direction of air flow Cooker hoods designed for use with an external motor EXT models have an integrated condensate trap Connection for air extraction Silencer optional accessory To achieve even further reductions in noise levels a special silencer can be fitted in the ducting system With air extraction The silencer not only reduces noise from the fan but also sounds from outside e g traffic noise For this reason the silencer must b
13. e New Zealand Miele New Zealand Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland NZ Tel 0800 264 353 Fax 0800 463 453 Internet www miele co nz Singapore Miele Southeast Asia Miele Pte Ltd 163 Penang Road 04 02 03 Winsland House Il Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail infosea miele com sg nternet www miele sg South Africa Miele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 27 0 11 548 1900 Fax 27 0 11 548 1935 E mail info miele co za nternet www miele co za United Arab Emirates Miele Appliances Ltd P O Box 11 47 82 Gold amp Diamond Park Sheikh Zayed Road Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 971 4 341 88 52 E Mail info miele ae Internet www miele ae Alteration rights reserved 0410 ce M Nr 07 782 070 00
14. e positioned as close as possible to where the ducting leaves the building air extraction with external fan To minimise noise from the fan in the kitchen the silencer should be positioned in front of the external fan 2 if possible or if the ducting is long then in the ducting inside the cooker hood itself In the case of an external fan placed inside the house fitting a silencer behind the external fan 9 reduces the noise of the fan outside the house In all modes of operation the most effective noise reductions are achieved if two silencers are fitted in the system 33 Electrical connection All electrical work should be undertaken by a suitably qualified and competent person in strict accordance with current national and local safety regulations BS 7671 in the UK Installation repairs and other work by unqualified persons could be dangerous for which the manufacturer cannot be held liable Ensure power is not supplied to the appliance until after installation or repair work has been carried out Do not connect the appliance to the mains electricity supply by an extension lead These do not guarantee the required safety of the appliance The connection data is given on the data plate This is visible when the grease filters have been removed Ensure that this data matches the household mains supply If the switch is not accessible after installation depending on country an
15. eration of the appliance P This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience or knowledge unless they are supervised whilst using it or have been shown how to use it by a person responsible for their safety Safety with children P This appliance is only intended for use by adults who have read these instructions It is not a toy To avoid the risk of injury keep children well away and do not allow them to play with it or use the controls They will not understand the potential dangers posed by it They should be supervised whenever you are working in the kitchen P Older children may use the cooker hood only when its operation has been clearly explained to them and they are able to use it safely recognising the dangers of misuse P Please be aware that on cooker hoods with halogen lighting the lamps will get very hot during use and remain hot for some time after switching off To safeguard against burning keep children well away from the lamps at all times Warning and safety instructions Technical safety P Before installation check the cooker hood for visible signs of damage Under no circumstances should you install or use a damaged appliance It could be dangerous P Before connecting the appliance to the mains supply make sure that the voltage and frequency details given on the data plate corr
16. ermin pay particular attention to keeping the appliance and its surroundings in a clean condition at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee Using at the same time as other heating appliances that depend on the air from the room Warning danger of toxic fumes AZ THHHHHH Ae U H Fr 0000 dai1474 P Great care should be taken when using the cooker hood at the same time and in the same room or area of the house as another heating appliance which depends on the air in the room Such appliances include gas oil wood or coal fired boilers and heaters continuous flow or other water heaters gas hobs cookers or ovens which draw air in from the room and duct exhaust gases out through a chimney or extraction ducting When used in extraction mode with or without an external motor fitted the appliance draws air in from the room in which it is installed and from neighbouring rooms If there is insufficient air an underpressure will occur The heating appliance may be starved of oxygen impairing combustion Harmful gases could be drawn out of the chimney or extraction ducting back into the room with potentially fatal consequences Warning and safety instructions In order to ensure safe operation and to prevent gases given off by the heating appliances from being drawn back
17. espond with the on site electricity supply otherwise the appliance could be damaged Consult a qualified electrician if in any doubt gt The electrical safety of this appliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system which complies with current local and national safety regulations It is most important that this basic safety requirement is present and tested regularly and where there is any doubt the household wiring system should be inspected by a qualified electrician The manufacturer cannot be held liable for the consequences of an inadequate earthing system e g electric shock P For safety reasons this appliance may only be used when it has been fully installed P Only open the housing as described in the instructions given in the installation sheet and in the Cleaning and care section of this booklet Under no circumstances should any other parts of the housing be opened Tampering with electrical connections or components and mechanical parts is highly dangerous to the user and can cause operational faults 6 P Installation maintenance and repairs may only be carried out by a Miele authorised person in strict accordance with current national and local safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work Ensure that current is not supplied t
18. g appliance which relies on air from the same room The cooker hood should be installed according to local and national building regulations Seek approval from the building inspector where necessary Only use smooth pipes or flexible hoses made from non flammable materials for the extraction ducting When using an external motor make sure that the exhaust ducting is sufficiently rigid The external motor can cause an underpressure which can result in the exhaust ducting distorting To achieve the greatest possible air extraction with the lowest noise level please note the following To ensure efficient air extraction the diameter of the exhaust ducting should not be less than 150 mm If flat ducting is being used the cross section must not be smaller than the cross section of the exhaust connection All ducting pipework and fittings must be of non flammable materials The exhaust ducting should be as short and straight as possible Only use wide radius bends The exhaust ducting should not be kinked or compressed Ensure that all connections are strong and airtight Where ducting is horizontal it must be laid to slope away at at least 1 cm per metre This is to ensure that condensate cannot drain back into the cooker hood 31 Connection for air extraction If the exhaust air is to be ducted into the open air the installation of a telescopic wall vent or roof vent available as an optional a
19. itched off when the cooker hood is in operation See also Warning and Safety instructions 35 Operation with Control module DSM 400 Connection to a light switch The control module can be used to Switch on the cooker hood lighting and also to dim it depending on model via a light switch in the house Installation The tower needs to be removed before the control module can be fitted to the fan unit The control module is supplied with its own detailed operating and installation instructions 36 Technical data Total connected load 240 W Fan qnolot ossis 200 W Hob lighting 4x10W Halogen lamps Osram type 44888 WFL 10 W Voltage idet dada quaeso sie 230 V Fregeney 2 4 04 ax s m nga 50 Hz Fuse rating GB essere iniseti 3A AUS NZ Plugrating ceea sisse 10A Test marks Electrical safety pan paa debe d rS C Tick Mark Electrically suppressed according to AS NZS 1044 Electrical cable length 1 5m Weight DA 289 4 0 0 020020 e 33 kg DA 289 4 EXT 2 2 2222 22222 30 kg Fan performance Extraction power according to EN 61591 Extraction system 150 mm Level Ju io cece ah oo eee 200 m3 h EES s cute Sean 300 m h Level Ill liiis sss sess 400 m h Level IV Intensive Setting 640 m h Extraction system 125 mm Kevelaer nes 180 m h level llus oe atte ee asa 280 m h Level Ill llis sss 380 m h Level IV Intensive Se
20. ll ees 26 Safety distance between hob and cooker hood S 0 000002 eee 27 Installation 1 e503 4 2440 RR nei tee gd eee REG Ese 28 Assembly DANS xad etd ee OP Lane does 28 Installation instructions sacs ere RRSUE RA uex mS X Red p P dene 30 PrOLGCHVOSTOI psa ito etum er Dont d hat po ok ean a ut Ce EIE dr nat 30 DESMAN eyre a TETTE 30 Connection for air extraction liliis lesen 31 Condensate tray s toch a b etes De E ele ede RO E od e docu ace dst 32 SIM ER PERENNE a r e e e E EEN 33 Electrical connection cc Coon een 34 Contents Operation with Control module DSM 400 00 35 Connection to a window contact switch isses 35 Potential free connection liie 35 Connection to a light switch iiie 36 Technicaldata sse ex e ES AEG Sa ir EE 37 Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled Packaging e g cling film polystyrene and plastic wrappings must be kept out of the reach of babies and young children Danger of suffocation Disposal of your old appliance Electrical and electronic appliances often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct func
21. n back on again The lighting will switch on at maximum brightness To dim the hob lighting The brightness of the lighting can be adjusted m With the lighting switched on press and hold the hob lighting control in The brightness will gradually dim until you release the control m Press the control in again to increase the brightness to the level required and then release it If you keep the control pressed in the light will continually change between bright and dim To switch the hob lighting off m Press the hob lighting control briefly to switch the lighting off m he indicator lamp will go out Operation Filter operating hours counter The number of hours the appliance has 0000 ala been in operation is stored in memory One or more of the indicator lamps for the controls will flash The number of flashing lamps shows the percentage of the operating time The indicator lamp for the grease filter which has already been used up control will come on after 30 hours of operation The vapour plate and the llamp 25 grease filter must then be cleaned 2lamps 50 3 lamps 75 Afterwards the operating hours counter 4 lamps 100 96 must be reset The number of operating hours used m To do this press and hold the grease remains in the memory even when the filter control for about 3 seconds appliance is switched off or there is a The indicator lamp for the grease filter Power cu
22. nd IV will come on Press the control to deactivate automatic switch off 5115 eo m Press the run on option control to confirm your selection m f you do not confirm your selection within 4 minutes the cooker hood will automatically revert to the old setting 16 Run on option It is advisable to run the fan for a few minutes after cooking is finished to neutralise any lingering odours in the air The fan can be set to switch off automatically after either 5 or 15 minutes 5215 66 m After cooking has finished press the run on option control whilst the fan is still running Press once The fan will switch off after 5 minutes left hand indicator lamp Press twice The fan will switch off after 15 minutes right hand indicator lamp To deactivate the run on option press the run on option contol again The appliance does not switch off automatically To switch the fan off LO oj m Press the On Off control to switch the fan off The indicator lamp will go out Operation To switch the hob lighting on Safety cut out The hob lighting can be switched on Should the cooker hood be left on the and off independently of the fan fan will switch off automatically after 10 hours The lighting will remain on a m Briefly press the lighting control to switch on the hob lighting m Pressing the On Off control will The indicator lamp will come on switch the fa
23. ndiluted washing up liquid Do not use cleaning agents containing descaling agents powder cleaners cream cleaners or abrasive all purpose cleaning agents Oven sprays Cleaning the grease filter in the dishwasher m Place the filters as upright as possible in the lower basket with the short sides upright and wash in a 65 C programme ensuring the spray arm is not obstructed If a Miele dishwasher is being used select the Sensor wash programme m Use a mild dishwasher detergent Depending on the cleaning agent used cleaning the filter in a dishwasher can cause permanent discolouration to the surface However this will not affect the functioning of the filter in any way m After cleaning leave the filter to dry for a while on an absorbent surface before putting it back in place m When cleaning the vapour plate please follow the instructions given under Housing earlier in this section m With the vapour plate and grease filter removed clean off any residues of oil or fat from the now accessible housing and channel on the lower housing to prevent the risk of these catching fire m After replacing the grease filter press the grease filter control for approximately 3 seconds to reset the operating hours counter The indicator lamp will go out If the vapour plate and grease filter are cleaned before the operating hours counter has reached its maximum the grease filter control should be
24. o the appliance until after maintenance or repair work has been carried out P Faulty components must only be replaced by genuine Miele original parts The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used P During installation maintenance and repair work the appliance must be disconnected from the mains electricity supply It is only completely isolated from the electricity supply when itis switched off at the isolator or the screw out fuse is removed in countries where this is applicable or the mains fuse is disconnected or itis switched off at the wall socket and the plug withdrawn or the fuse from the fused spur connection until is withdrawn Warning and safety instructions P Do not connect the appliance to the mains electricity supply by a multi socket unit or an extension lead These do not guarantee the required safety of the appliance e g danger of overheating P For appliances with an external fan motor fitted EXT models the connection of the two units must be made using the connection cable and the plug connectors These models may only be combined with a Miele external motor P This appliance may only be used in mobile installations if a risk assessment of the installation has been carried out by a suitably qualified engineer P In areas which may be subject to infestation by cockroaches or other v
25. pliance is under guarantee please contact Your Miele Dealer Chartered Agent or The Miele Service Department see back cover for address When contacting your Dealer or Miele please quote the model and serial number of your appliance These are shown on the data plate which is visible when the grease filter is removed For G B Please note that telephone calls may be monitored and recorded for training purposes N B A call out charge will be applied for service visits where the problem could have been resolved as described in these instructions 25 Appliance dimensions r 320 250 4 960 1320 685 The diagram is not drawn to scale 26 Appliance dimensions The shaded areas 1 and 2 represent the wall or ceiling area for the vent cut out for fitting the connection socket and in the case of EXT models for feeding the connection cable through to an external fan Connection for air extraction 150 mm or 125 mm with reducing collar Safety distance between hob and cooker hood S The safety distance between the top of a cooker or hob and the bottom of the cooker hood canopy must measure at least 365 mm unless a greater distance is specified by the manufacturer of your cooking appliance See Warning and Safety instructions Account should also be taken of the height of
26. pressed for approximately 6 seconds to reset the counter to zero m Push the grease filter into position until it engages daiti93b m Hook the vapour plate into the bottom of the housing push it slightly to the left and then raise it up towards the appliance and click it into position 23 Cleaning and care Changing a halogen lamp m Before any cleaning or maintenance work disconnect the cooker hood from the mains supply Ensure that itis switched off at the isolator or itis switched off at the wall socket and the plug is withdrawn or the fuse from the fused spur connection unit is withdrawn or the mains fuse is disconnected or the screw out fuse is removed in countries where this is applicable N Exercise caution when changing halogen lamps They get very hot during use and remain hot for some time after being switched off Let them cool down before you change them 24 m Use the lever supplied to pull the halogen lamp out of its socket Take care not to let the lamp fall onto the hob below m Insert the new halogen lamp into its socket and carefully push into position Please follow the manufacturer s instructions When replacing a defective lamp you should use exactly the same type of lamp see Technical data for lamp specification After Sales Service In the event of a fault which you cannot correct yourself or if the ap
27. s of a control appliance must be fitted in the exhaust cable and is operated by the controls socket in the motor unit on the cooker hood Having a non return flap fitted in the ducting ensures that air once ducted to the outside cannot get back into the room again The flap is closed when the cooker hood is switched off When the cooker hood is switched on the non return flap opens for the cooking vapours to be ducted away Guide to the appliance X ee ee ee Ben V a 2 Guide to the appliance Extension piece 2 Tower Canopy 4 Touch controls 8 Hob lighting Grease filter Vapour plate Touch control for the hob lighting This control switches the lighting on and off and is also a dimmer switch On Off touch control for the fan Touch controls to select fan power level Touch control for the run on option The fan can be set to continue running and switch off automatically after either 5 or 15 minutes 42 Touch control for the grease filter The indicator lamp for the grease filter touch control lights up when the vapour plate and grease filter need to be cleaned The touch control is used to reset the operating hours counter every time the vapour plate and the grease filter are cleaned see Cleaning and care It can also be used to check and alter the operating hours counter
28. section of this booklet must be The manufacturer cannot be held maintained unless the hob liable for damage caused by manufacturer states that a greater non compliance with these Warning safety distance is required and Safety instructions If more than one cooking appliance is fitted beneath the cooker hood and they have different minimum safety distances to the cooker hood select the greater distance P Safety regulations prohibit the fitting of a cooker hood over solid fuel stoves P All ducting pipework and fittings must be of non flammable material These can be obtained from the Miele Spare Parts department or from builders merchants P The appliance must not be connected to a chimney or vent flue which is in use Neither should it be connected to ducting which ventilates rooms with fireplaces gt If exhaust air is to be extracted into a chimney or ventilation duct no longer used for other purposes seek professional advice 10 Modes of operation The cooker hood works with air extraction an external fan EXT models only mm JUS auum The air is drawn in through the vapour plate cleaned by the grease filter and The EXT models are designed to be directed outside connected to an external fan located If the on site ventilation system does outside the room not have a non return flap the The external motor is connected to the non return flap supplied with the cooker hood by mean
29. t control will go out Reading the filter operating hours counter To check the percentage of time set already used LO oj m Press the On Off control to switch the fan on m Press the grease filter control 18 Operation To alter the filter operating hours counter This can be lengthened or shortened to suit the type of cooking you do You can choose from 20 30 40 or 50 hours Select a short time if you fry a lot f you use very little fat for cooking select a longer time If you only cook occasionally we recommend that you select a short time because grease which has built up gradually over a long period of time will harden on the grease filter and make cleaning more difficult D oj m Press the On Off control to switch the fan off m Press the run on option control and the grease filter control at the same time The indicator light for the grease filter control and one of the lights for the 4 controls will flash 0000 The control lamps show the time which has been set 1st lamp from the left 20 hours 2nd lamp from the left 2 30 hours 3rd lamp from the left 2 40 hours 4th lamp from the left 2 50 hours m Use the controls to select the desired time m Confirm the selection by pressing the grease filter control If you do not confirm your selection within 4 minutes the cooker hood will automatically revert to the
30. the person who will be using the hood most often The person should have sufficient space to work comfortably atthe hob and also be able to reach the hood controls with ease If positioned too high extraction will be inefficient The height of the cooking appliance must be taken into account when planning the installation height of the cooker hood 27 Installation Assembly parts dai2707 Installation 3 protective sheets for use when fitting the tower 2 Upper retaining plate for securing the extension piece 3 Middle retaining plate for securing the extension piece 1 exhaust connection for exhaust ducting 150 mm 1 reducing collar for exhaust ducting 125 mm 1 non return valve for fitting into the exhaust socket on the motor unit not needed for recirculation mode 6 me Q 5 large headed screws 5 x 40 mm and 5 x S 8 plugs for securing the retaining plates and the appliance unit Q 2 screws 5 x 60 mm and 2xS8R 60 plugs for securing the appliance unit The screws and plugs are designed for use in solid walls only For other types of wall construction alternative fixings will be required Make sure that the wall is able to take the weight of the cooker hood Om 6 screws 3 5 x 9 5 mm for securing the canopy and the filter housing CE 2 cover caps mm E 1 lever for changing the halogen lamp and dismantling
31. tion or damage if soiling is left on them for too long Remove soiling straight away Observe the General notes on cleaning earlier in this section Do not use stainless steel cleaning agents on the controls Glass surfaces Glass surfaces can be cleaned using a proprietary non abrasive cleaning agent designed specifically for use on glass Avoid oven sprays Vapour plate and grease filter The vapour plate and the re useable metal grease filter remove solid particles from the kitchen vapours grease dust etc preventing soiling of the cooker hood e o The vapour plate and grease filter should be cleaned regularly at least every 3 4 weeks to avoid a build up of grease but always clean immediately if the grease filter control lamp comes on An oversaturated filter is a fire hazard 22 To avoid damaging the filter or the hob below make sure you hold the filter securely at all times when handling it To remove the vapour plate dai1193a m Pull the vapour plate down towards you at the top push the bottom slightly to the right and pull forwards to remove see illustration To remove the grease filter dai0954 m Pull the grease filter by the hand hold forwards and out Cleaning and care Cleaning the grease filter by hand m Clean the filter with a soft nylon brush in a mild solution of hot water and a small amount of washing up liquid Do not use u
32. tioning of your appliance Please do not therefore dispose of it with your household waste Please dispose of it at your local community waste collection recycling centre or contact your dealer for advice Ensure that it presents no danger to children while being stored for disposal Warning and safety instructions This appliance complies with all relevant local and national safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the appliance please read these instructions carefully before using it for the first time They contain important information on the safety installation use and maintenance of the appliance Keep these instructions in a safe place and ensure that all users are familiar with the contents Pass them on to any future owner of the appliance Correct application P This appliance is not designed for commercial use It is intended for use in domestic households and for use in similar working and residential environments such as Shops Offices and showrooms and by residents in establishments such as Hostels and guesthouses P It must only be used as a domestic appliance to extract vapours and remove odours from cooking Any other usage is not supported by the manufacturer and could be dangerous Miele cannot be held liable for damage resulting from incorrect or improper use or op
33. tting 580 m h For EXT models the connected load and extraction power will depend on the type of external motor fitted EXT models Length of connection cable to external NOLO Ms Zaren ee 1 9m 37 38 39 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW Tel 0845 365 0555 Fax 0845 365 0777 Customer Contact Centre Tel 0845 365 6600 E mail info miele co uk Internet www miele co uk Australia Miele Australia Pty Ltd ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 03 9764 7130 Fax 03 9764 7149 Internet www miele com au China Miele Shanghai Suite 4105 06 Plaza 66 1266 Nanjing Road West Jing An District Shanghai 200040 PRC Tel 86 21 6288 4200 Fax 86 21 6288 4100 E mail mieleshanghai cn miele com Internet www miele cn Miele Hong Kong Limited 41 F 4101 Manhattan Place 23 Wang Tai Road Kowloon Bay Hong Kong Tel 852 2610 1331 Fax 852 2610 1013 Email mielehk miele com hk India Miele Appliances India Pvt Ltd Ground Floor Copia Corporate Suites Plot No 9 Jasola New Delhi 110025 Tel 011 46 900 000 Fax 011 46 900 001 E mail customercareQmiele in Internet www miele in Germany Miele amp Cie KG Carl Miele StraBe 29 33332 G tersloh Ireland Miele Ireland Ltd Broomhill Road Tallaght Dublin 24 Tel 01 461 0710 Fax 01 461 07 97 E Mail info miele ie Internet www miele i
Download Pdf Manuals
Related Search