Trendnet TEG-PCITXRL
Contents
1. Quick Installation Guide BIS TEG PCITXR TEG PCITXRL 3 02 Table of Contents Version 03 18 2010 1 Before You Start Package Contents e TEG PCITXR TEG PCITXRL e CD ROM Driver e Multi Language Quick Installation Guide e l Oo Z W _ System Requirements e 32 bit PCI 2 1 slot e CD ROM Drive e CPU 1GHz or above Windows 7 800MHz or above Windows Vista 300Mhz or above Windows XP 2000 ME 98 e Memory 1GB RAM or above Windows 7 512MB RAM or above Windows Vista 256MB RAM or above Windows XP 2000 ME 98 e Windows 7 32 64 bit Vista 32 64 bit XP 32 64 bit 2000 ME 98 e A RJ 45 Ethernet cable 2 How to Install Note 1 For Windows 98SE and Me driver installation refer to the user guide on the Driver CD ROM 2 Do not insert the TEG PCITXR TEG PCITXRL until instructed to do so ENGLISH 1 Insert the Driver CD ROM into your computer s CD ROM Drive Windows Vista XP 2000 ga DVD CD RW Drive F sv TEG PCITXR amp TEG PCITXRL Always do this for software and games tttr ur_t6t 1 111 lt 111179 2 Click Run autorun exe Windows Vista only gt General options h Open folder to view files AutoPlay its in Control Panel TRENDnet 3 Click Install Driver Windows Vista XP 2000 4 Follow the InstallShield Wizard instructions Windows Vista XP 2000 The Microsolt a affams that2. icon and then right click the Local Area Connection icon and then click Bridge Connections Properties Create Shortcut Rename Properties Use the folowing IP address 2 Click Internet Protocol TCP IP and then click Properties Then click on Obtain an IP address automatically 4 How do install the drivers on Windows 98 or ME Please refer to the User s Guide included on the Driver CD ROM 5 Why am I only getting a network connection speed of 100Mbps instead of 1000Mbps 1 Check the Ethernet Cable Make sure you are using CAT 5e or CAT 6 Ethernet Cables Some CAT 5 cables are not rated to run in Gigabit 2 Make sure you are connected to a 1000Mbps switch If you still encounter problems or have any questions regarding the TEG PCITXR TEG PCITXRL please refer to the User s Guide included on the Driver CD ROM or contact Trendnet s Technical Support Department Certifications This equipment has been tested and found to comply with FCC and CE Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received Including interference that may cause undesired operation Waste electrical and electronic products must not be disposed of with household waste Please C CF recycle where facilities exist Check with you Local Authority or Retailer for recycling advice o NOTE THE MANUFACTURER IS NOT RESPONSI
3. software has been tested with and that the software has not been ahesed since was tested The soltware pou are about lo instal does not contain a Microsoft digital sgnature Therefore guarantee that this software works comectiy Unknown software package 5 Click Yes Windows 2000 only ii te oe Odi Do you wart to continus the inctallation No More Inlo 6 Click Finish Windows Vista XP 2000 2 l Oo Z LUI 7 Shutdown your computer and then open your computer s Case 8 Insert PCI Card firmly into an available PCI slot and then turn ON the computer and wait until the Windows desktop appears 9 Drivers will install automatically The Microsolt digital signature affirms that software has been tested with Windows and that the software has not been alteted since was tested The software you ate about to install does not contain a Microsoft there is no 10 Click Yes Windows 2000 only qui e a i n hitp windowsupdate 11 Connect a RJ 45 network cable from the computer to an available Ethernet port on your router or switch ENGLISH Your Installation is complete For detailed information regarding the TEG PCITXR TEG PCITXRL s configuration and advanced settings please refer to the Troubleshooting section User s Guide on the Utility CD ROM or TRENDnet s website at http www trendnet com Register Your Product To ensure the highest level o
4. BLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT SUCH MODIFICATIONS COULD VOID THE USER S AUTHORITY TO OPERATE THE EQUIPMENT ADVERTENCIA En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de alimentac n necesario para su funcionamiento El uso de un adaptador distinto al mencionado puede producir da os fisicos y o da os al equipo conectado El adaptador de alimentaci n debe operar con voltaje y frecuencia de la energia electrica domiciliaria existente en el pais o zona de instalaci n TRENDNET Copyright 02010 All Rights Reserved TRENDnet
5. e manager fails to recognize the presence of a new networking adapter verify that the network adapter is firmly seated in the PCI slot 4 Plug the adapter into another PCI slot on your computer 3 Windows recognizes my new hardware but I m unable to connect to my network What should do 1 Verify that the RJ 45 Ethernet Cable is securely connected from your switch or router to your network adapter 2 Verify that the LEDs on your network card are lit Verify that the TCP IP settings are set to Obtain an IP address automatically see the steps below Windows 7 1 Go into the Control Panel click Network and Re leh Internet click Network and Sharing Center Status click Change Adapter Settings and then its right click the Local Area Connection icon and then click Properties a E 2 Click Internet Protocol Version 4 TCP IPv4 and then click Properties Then click on Obtain an IP address automatically Windows Vista 1 Go into the Control Panel click Network and Ki Internet click Network and Sharing Center S NVIDIA ni Disable click Manage Network Connections and then right click the Local Area Connection icon and then click Properties Local Area Connection rm ere 2 Click Internet Protocol Version 4 TCP IPv4 and then click Properties Then click on Obtain an IP address automatically Windows XP 2000 2003Server Disable 1 Go into the Control Panel double click the Status Network Connections
6. f customer service and support please take a moment to register your product Online at www trendnet com register Thank you for choosing TRENDnet Troubleshooting 1 inserted the Driver CD ROM into my computer s CD ROM drive and the installation menu does not appear automatically What should do 1 For Windows Vista if the installation menu does not appear automatically click Start click the Start Search box and type D lautorun exe where D in D autorun exe is the letter assigned to your CD ROM Drive and then press the ENTER key on your keyboard 2 For Windows 2000 XP if the installation menu does not appear automatically click Start click Run and type D lautorun where D in D autorun exe is the letter assigned to your CD ROM Drive and then press the ENTER key on your keyboard 2 Windows doesn t recognize my new hardware What should do 1 Verify that your computer meets the system requirements as specified in Section 1 2 Access your device manager to make sure the adapter is installed properly If you see a networking device with a yellow question mark or exclamation point you will need to reinstall the device and or the drivers To access the device manager on Windows 2000 XP right click My Computer click Properties click the Hardware tab and then click Device Manager To access the device manager on Windows 7 Vista right click Computer click Properties and then click Device Manager 3 If the devic
Download Pdf Manuals
Related Search