Metra XSVI-2105 electrical connector assembly
Contents
1. In the GM vehicles listed below there are no 12 volt accessory wires currently in the factory harness mak ing the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio The XSVI 2105 is designed to pro vide a 12 volt 10 amp switched accessory output along with the rest of the wires needed to install an aftermarket radio The R A P Retained Accessory Power function where power is supplied to the radio after the ignition is shut off until one of the front doors are opened is retained by the XSVI 2105 NOTE The XSVI 2105 does not retain the factory warning chimes Onstar or the factory amplifier if so equipped INITIALIZE THE XSVI INTERFACE BEFORE TURNING ON RADIO With all connections made and har nesses connected to the vehicle turn ignition key to the ON position for thirty seconds then turn key off Wiring the XSVI 2105 Wiring up the XSVI 2105 is like wiring up any other wire harness that would attach to the aftermarket radios harness The Metra EIA wire code can be found on the back of this package that will aid you in the wiring of your aftermarket radio See Applications on back of page In the GM vehicles listed below there are no 12 volt accessory wires currently in the factory harness mak ing the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio Th2. gee APPLICATIONS mm Buick GMC e Enclave 2007 09 eAcadia 2007 09 e Lucerne 2006 09 eSavanna 2008 10 Cadillac eSierra New body 2007 10 e DTS 2006 09 Yukon XL 2007 10 SRX 2007 09 Hummer Chevrolet H2 2008 09 e Avalanche 2007 10 Pontiac Equinox 2007 09 Torrent 2007 09 Express 2008 10 Vibe 2009 mpala 2006 10 Only required for retention of e Monte Carlo 2006 07 2 Star NAV outputs not e Silverado new body applicable 2007 10 Saturn e Suburban 2007 10 Outlook 2007 09 Tahoe 2007 10 Vue 2008 09 Traverse 2009 10 Suzuki XL 7 2007 09 REV 03 10 10 INSTXSVI 2105 1 800 221 0932 www metraonline com METRA ELECTRONICS CORPORATION COPYRIGHT 2010 Buick GMC Enclave 2007 09 eAcadia 2007 09 Lucerne 2006 09 eSavanna 2008 10 Cadillac Sierra New body 2007 10 DTS 2006 09 Yukon XL 2007 10 e SRX 2007 09 Hummer Chevrolet H2 2008 09 e Avalanche 2007 10 Pontiac Equinox 2007 09 Torrent 2007 09 Express 2008 10 Vibe 2009 e Impala 2006 10 Only required for retention of e Monte Carlo 2006 07 278tar NAV outputs not e Silverado new body applicable 2007 10 Saturn e Suburban 2007 10 Qutlook 2007 09 e Tahoe 2007 10 Vue 2008 09 e Traverse 2009 10 Suzuki XL 7 2007 09 REV 03 10 10 INSTXSVI 2105 1 800 221 0932 www metraonline com METRA ELECTRONICS CORPORATION COPYRIGHT 2010 METRA ELECTRONICS CORPORATION COPYRI
3. to the vehicle turn ignition key to the ON position for thirty seconds then turn key off Wiring the XSVI 2105 Wiring up the XSVI 2105 is like wiring up any other wire harness that would attach to the aftermarket radios harness The Metra EIA wire code can be found on the back of this package that will aid you in the wiring of your aftermarket radio See Applications on back of page MEE XSVI 2105 Se INSTALLATION INSTRUCTIONS In the GM vehicles listed below there are no 12 volt accessory wires currently in the factory harness mak ing the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio The XSVI 2105 is designed to pro vide a 12 volt 10 amp switched accessory output along with the rest of the wires needed to install an aftermarket radio The R A P Retained Accessory Power function where power is supplied to the radio after the ignition is shut off until one of the front doors are opened is retained by the XSVI 2105 NOTE The XSVI 2105 does not retain the factory warning chimes Onstar or the factory amplifier if so equipped INITIALIZE THE XSVI INTERFACE BEFORE TURNING ON RADIO With all connections made and har nesses connected to the vehicle turn ignition key to the ON position for thirty seconds then turn key off Wiring the XSVI 2105 Wiring up the XSVI 2105 is like wiring up any other wire harness
4. 21 0932 www metraonline com METRA ELECTRONICS CORPORATION COPYRIGHT 2010 MEE XSVI 2105 NEEUEUEN MEE XSVI 2105 EEENEN ENENN Xsvi c 05 EN INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS In the GM vehicles listed below there are no 12 volt accessory wires currently in the factory harness mak ing the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio The XSVI 2105 is designed to pro vide a 12 volt 10 amp switched accessory output along with the rest of the wires needed to install an aftermarket radio The R A P Retained Accessory Power function where power is supplied to the radio after the ignition is shut off until one of the front doors are opened is retained by the XSVI 2105 NOTE The XSVI 2105 does not retain the factory warning chimes Onstar or the factory amplifier if So equipped INITIALIZE THE XSVI INTERFACE BEFORE TURNING ON RADIO With all connections made and har nesses connected to the vehicle turn ignition key to the ON position for thirty seconds then turn key off Wiring the XSVI 2105 Wiring up the XSVI 2105 is like wiring up any other wire harness that would attach to the aftermarket radios harness The Metra EIA wire code can be found on the back of this package that will aid you in the wiring of your aftermarket radio See Applications on back of page
5. GHT 2010 Eam APPLICATIONS mm Buick GMC e Enclave 2007 09 eAcadia 2007 09 e Lucerne 2006 09 eSavanna 2008 10 Cadillac Sierra New body 2007 10 DTS 2006 09 Yukon XL 2007 10 SRX 2007 09 Hummer Chevrolet H2 2008 09 e Avalanche 2007 10 Pontiac Equinox 2007 09 Torrent 2007 09 Express 2008 10 Vibe 2009 e Impala 2006 10 Only required for retention of e Monte Carlo 2006 07 Onstar NAV outputs not Silverado new body applicable 2007 10 Saturn e Suburban 2007 10 Qutlook 2007 09 e Tahoe 2007 10 Vue 2008 09 Traverse 2009 10 Suzuki XL 7 2007 09 REV 03 10 10 INSTXSVI 2105 1 800 221 0932 www metraonline com METRA ELECTRONICS CORPORATION COPYRIGHT 2010 METRA ELECTRONICS CORPORATION COPYRIGHT 2010 EH APPLICATIONS mm Buick GMC Enclave 2007 09 Acadia 2007 09 Lucerne 2006 09 eSavanna 2008 10 Cadillac eSierra New body 2007 10 DTS 2006 09 e Yukon XL 2007 10 SRX 2007 09 Hummer Chevrolet H2 2008 09 e Avalanche 2007 10 Pontiac Equinox 2007 09 Torrent 2007 09 Express 2008 10 Vibe 2009 Impala 2006 10 Only required for retention of e Monte Carlo 2006 07 Onstar NAV outputs not Silverado new body applicable 2007 10 Saturn Suburban 2007 10 Outlook 2007 09 Tahoe 2007 10 Vue 2008 09 e Traverse 2009 10 Suzuki XL 7 2007 09 REV 03 10 10 INSTXSVI 2105 1 800 2
6. e XSVI 2105 is designed to pro vide a 12 volt 10 amp switched accessory output along with the rest of the wires needed to install an aftermarket radio The R A P Retained Accessory Power function where power is supplied to the radio after the ignition is shut off until one of the front doors are opened is retained by the XSVI 2105 NOTE The XSVI 2105 does not retain the factory warning chimes Onstar or the factory amplifier if so equipped INITIALIZE THE XSVI INTERFACE BEFORE TURNING ON RADIO With all connections made and har nesses connected to the vehicle turn ignition key to the ON position for thirty seconds then turn key off Wiring the XSVI 2105 Wiring up the XSVI 2105 is like wiring up any other wire harness that would attach to the aftermarket radios harness The Metra EIA wire code can be found on the back of this package that will aid you in the wiring of your aftermarket radio See Applications on back of page MEE XSVI 2105 Sa MEE XSVI 2105 NNENEN MEE XSVI 2105 INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS In the GM vehicles listed below there are no 12 volt accessory wires currently in the factory harness mak ing the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio The XSVI 2105 is designed to pro vide a 12 volt 10 amp switched accessory output along with the rest of the wir
7. es needed to install an aftermarket radio The R A P Retained Accessory Power function where power is supplied to the radio after the ignition is shut off until one of the front doors are opened is retained by the XSVI 2105 NOTE The XSVI 2105 does not retain the factory warning chimes Onstar or the factory amplifier if so equipped INITIALIZE THE XSVI INTERFACE BEFORE TURNING ON RADIO With all connections made and har nesses connected to the vehicle turn ignition key to the ON position for thirty seconds then turn key off Wiring the XSVI 2105 Wiring up the XSVI 2105 is like wiring up any other wire harness that would attach to the aftermarket radios harness The Metra EIA wire code can be found on the back of this package that will aid you in the wiring of your aftermarket radio See Applications on back of page INSTALLATION INSTRUCTIONS In the GM vehicles listed below there are no 12 volt accessory wires currently in the factory harness mak ing the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio The XSVI 2105 is designed to pro vide a 12 volt 10 amp switched accessory output along with the rest of the wires needed to install an aftermarket radio The R A P Retained Accessory Power function where power is supplied to the radio after the ignition is shut off until one of the front doors are opened is retained b
8. lac DTS 2006 09 SRX 2007 09 Chevrolet Avalanche 2007 10 Equinox 2007 09 Express 2008 10 mpala 2006 10 Monte Carlo 2006 07 Silverado new body 2007 10 Suburban 2007 10 Tahoe 2007 10 Traverse 2009 10 REV 03 10 10 1 800 221 0932 GMC Acadia 2007 09 eSavanna 2008 10 Sierra New body 2007 10 eYukon XL 2007 10 Hummer H2 2008 09 Pontiac Torrent 2007 09 e Vibe 2009 Only required for retention of Onstar NAV outputs not applicable Saturn Qutlook 2007 09 Vue 2008 09 Suzuki XL 7 2007 09 INSTXSVI 2105 www metraonline com EH APPLICATIONS mum Buick Enclave 2007 09 Lucerne 2006 09 Cadillac DTS 2006 09 SRX 2007 09 Chevrolet Avalanche 2007 10 Equinox 2007 09 Express 2008 10 Impala 2006 10 Monte Carlo 2006 07 e Silverado new body 2007 10 e Suburban 2007 10 Tahoe 2007 10 e Traverse 2009 10 REV 03 10 10 1 800 221 0932 GMC eAcadia 2007 09 Savanna 2008 10 Sierra New body 2007 10 Yukon XL 2007 10 Hummer H2 2008 09 Pontiac Torrent 2007 09 Vibe 2009 Only required for retention of Onstar NAV outputs not applicable Saturn Outlook 2007 09 Vue 2008 09 Suzuki XL 7 2007 09 INSTXSVI 2105 www metraonline com METRA ELECTRONICS CORPORATION COPYRIGHT 2010 METRA ELECTRONICS CORPORATION COPYRIGHT 2010 ge APPLICATIONS am
9. mm APPLICATIONS am Buick Enclave 2007 09 Lucerne 2006 09 Cadillac DTS 2006 09 SRX 2007 09 Chevrolet Avalanche 2007 10 Equinox 2007 09 Express 2008 10 mpala 2006 10 Monte Carlo 2006 07 Silverado new body 2007 10 e Suburban 2007 10 Tahoe 2007 10 Traverse 2009 10 REV 03 10 10 1 800 221 0932 GMC Acadia 2007 09 eSavanna 2008 10 Sierra New body 2007 10 eYukon XL 2007 10 Hummer H2 2008 09 Pontiac Torrent 2007 09 Vibe 2009 Only required for retention of Onstar NAV outputs not applicable Saturn e Outlook 2007 09 Vue 2008 09 Suzuki XL 7 2007 09 INSTXSVI 2105 www metraonline com EH APPLICATIONS mm Buick Enclave 2007 09 Lucerne 2006 09 Cadillac e DTS 2006 09 e SRX 2007 09 Chevrolet Avalanche 2007 10 Equinox 2007 09 Express 2008 10 mpala 2006 10 Monte Carlo 2006 07 e Silverado new body 2007 10 e Suburban 2007 10 Tahoe 2007 10 Traverse 2009 10 REV 03 10 10 1 800 221 0932 GMC eAcadia 2007 09 eSavanna 2008 10 Sierra New body 2007 10 eYukon XL 2007 10 Hummer H2 2008 09 Pontiac Torrent 2007 09 Vibe 2009 Only required for retention of Onstar NAV outputs not applicable Saturn Qutlook 2007 09 Vue 2008 09 Suzuki XL 7 2007 09 INSTXSVI 2105 www metraonline com gee APPLICATIONS mm Buick Enclave 2007 09 Lucerne 2006 09 Cadil
10. that would attach to the aftermarket radios harness The Metra EIA wire code can be found on the back of this package that will aid you in the wiring of your aftermarket radio See Applications on back of page HE XSVI 2105 INSTALLATION INSTRUCTIONS In the GM vehicles listed below there are no 12 volt accessory wires currently in the factory harness mak ing the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio The XSVI 2105 is designed to pro vide a 12 volt 10 amp switched accessory output along with the rest of the wires needed to install an aftermarket radio The R A P Retained Accessory Power function where power is supplied to the radio after the ignition is shut off until one of the front doors are opened is retained by the XSVI 2105 NOTE The XSVI 2105 does not retain the factory warning chimes Onstar or the factory amplifier if so equipped INITIALIZE THE XSVI INTERFACE BEFORE TURNING ON RADIO With all connections made and har nesses connected to the vehicle turn ignition key to the ON position for thirty seconds then turn key off Wiring the XSVI 2105 Wiring up the XSVI 2105 is like wiring up any other wire harness that would attach to the aftermarket radios harness The Metra EIA wire code can be found on the back of this package that will aid you in the wiring of your aftermarket radio See Applica
11. tions on back of page
12. y the XSVI 2105 NOTE The XSVI 2105 does not retain the factory warning chimes Onstar or the factory amplifier if so equipped INITIALIZE THE XSVI INTERFACE BEFORE TURNING ON RADIO With all connections made and har nesses connected to the vehicle turn ignition key to the ON position for thirty seconds then turn key off Wiring the XSVI 2105 Wiring up the XSVI 2105 is like wiring up any other wire harness that would attach to the aftermarket radios harness The Metra EIA wire code can be found on the back of this package that will aid you in the wiring of your aftermarket radio See Applications on back of page In the GM vehicles listed below there are no 12 volt accessory wires currently in the factory harness mak ing the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio The XSVI 2105 is designed to pro vide a 12 volt 10 amp switched accessory output along with the rest of the wires needed to install an aftermarket radio The R A P Retained Accessory Power function where power is supplied to the radio after the ignition is shut off until one of the front doors are opened is retained by the XSVI 2105 NOTE The XSVI 2105 does not retain the factory warning chimes Onstar or the factory amplifier if so equipped INITIALIZE THE XSVI INTERFACE BEFORE TURNING ON RADIO With all connections made and har nesses connected
Download Pdf Manuals
Related Search