Mustang MV-PROJSP-FLAT-W projector accessory
Contents
1. Installation Guide 1 7 Assemble the selected Extension Bracket with the following items Bottom Spacer Spacer if needed amp Square Nut For Extension Bracket more than 50mm 1 97 Square Nut X 2 Bottom Spacer Spacer of Various Size ST Oo si Bottom Spacer Bottom Spacor Spacer of Various Sizo 1 9a Assemble the Universal Base Plate with the required items as shown in the picture M6 Nut Qty 2pcs amp 2 4 A Gi U Joint Bracket Qty Ipc Universal Base Plate Qty Ipc A A M6 Carriage bolt Qty 2pcs 1 10 Align the assembled Universal Base Plate with all the Extension Bracket as shown in the picture Using M5 Button Socket Cap Screws to hand tighten it 1 8 Assemble the respective Extension Bracket to the Projector as shown in the picture Using respective Truss Head Screw from the given package to tighten lightly Full assembled of the Universal Base Plate as shown in the picture Do not tighten the M6 Nut until the CG is finalized 1 11 Attach the Assemble Parts as in step 1 6 to the Universal Base Plate as shown Lift up the Projector to check the CG of the assembly before force tightening the M5 Button Socket Cap Screws and the M Nut The assembly is then completed Installation Guide 1 12 For easy and quick installation the universal base has been pre installed 2 Installation of Universal Ceiling Mounting Kit 2 1 2 2 Install the Ceiling plate to the2. injury and damage to properties or the unit collapsing from its installed position v Do not install at place where there are excessive When a malfunction occur disconnect the dust and smoke as fire could arise from these power from the main socket and surround the area with ropes to prevent others from getting near it Do not install near an air conditioner sources Check and ensure the ceiling where you install can support the load of the unit and Ceiling Mounting Steps should be taken to ensure the ceiling and Keep the room well ventilated to prevent room installed unit can withstand external forces like 5 temperature rising and possibilities resulting in 100mm 3 94 or moro earthquakes vibrations etc z fire 100mm 3 94 or more All Ceiling Mounting Brackets are to be firmly Do not install in location where room temperature secured so the unit will not drop off its installed Allen Key a and humidity are excessively high to prevent fire position ao 3 To prevent the fire avoid contacting with water Do not remove any bolts and screws from the Ceiling Do not apply unnecessary stress or load on the Mounting Brackets or do any changes to the Ceiling installed unit Mounting Brackets Package Contents Package Contents Each package should contain the parts listed as shown below Part 11 Part 12 Washer M8 Spring Washer Part 1 Part 2 Ceiling Plate U Brocket Part 13 Part 14 Bot
3. Installation Guide MUSANG Universal Projector Low Profile Mount MV PROJSP FLAT W Important Notes Parts Specifications Thank you for purchasing the Universal Projector Flush Mount This bracket is suitable for about 80 to 90 of projectors up tol 5kg 3316s To ensure correct usage please read this instruction manual thoroughly Keep this manual for future reference Bracket should be mounted only by qualified installer User will be responsible for any injuries and damages that may arise from improper installation and handling of Universal Ceiling Mounting Kit Ensure all mounting screws are appropriately positioned and properly tightened fastened Installers are to ensure customer s safety during installation We reserve the right to amend or undertake any necessary changes without prior notice WARNING This symbol indicates the incorrect handling Ignoring this symbol can result in the possibility of personal injury or even death AN CAUTION This symbol indicates the incorrect handling Ignoring this symbol can result in the possibility of personal injury and physical damage A This symbol indicates additional cautions including warnings O This symbol indicates forbidden actions Q This symbol indicates required actions A Q O Caution Forbidden Required general general general Z WARNING Z CAUTION Assembling without the use of bolts and screws at designated points may result in
4. ceiling by M10 bolt Install Shoft not included into the ceiling Connect the shoft with the Bottom Column Rsferia dicon insert the Locking Hook into the cutting slot gram Tighten them with M8x50 Socket Cap Screw and M8 Self Locking Nylon Nut Refer to drawing 2 3 Installation completed Please consult our authorized service person when you meet any trouble in installation We are not liable for any damage or injury caused by mishandling or improper operation 10
5. tom Spacer Square Nut Part 3 Extension Brocket Part 16 General Base Plate Part 15 M6x12 Carriage Bolt M5x10 Socket Button Cap Screw Part 5 Cross Adapter Part 18 a M6 Serrate Flange Nut Truss Head Screw M4x15 M4x20 M4x25 4 pcs each Part 7 M5x15 M5x20 M5x25 4 pcs each Locking Hook M6x15 M6x20 M6x25 4 pcs each Part 9 Socket Cap Screw Part 10 M8 Self Locking Nylon Nut Installation Guide 1 Parts Assembly Installation of Universal Base 1 1 Lift the Projector with both middle finger along the depth of the Projector to search for the Central Gravity CG 1 3 When the CG Point Depth of Projector and Width of projector intersection meet that will be the assume CG of Projector CG of Projector CG of Point Width of Projector Select the suitable Extension Bracket from the Package There are 4 sizes available as shown 1 2 Lift the Projector with both middle finger along the depth of the Projector to search for the Central Gravity CG h 1 4 Locate the Projector CG Position and determine screw size for mounting the Projector Place the Universal Base Plate near to the Projector CG and select the suitable Extension Bracket given in the package Thread 1 6 Select the suitable Extension Bracket and place it on the Projector near the CG position follow by the Universal Base Plate Make sure the Extension Bracket is able to assemble to the Universal Base Plate
Download Pdf Manuals
Related Search