Chief FWS110B flat panel wall mount
Contents
1. ALLOWABLE NE AREA Figure 18 Allowable Arm Area 7 Repeat Steps 2 through 6 for second mount arm assembly 10 8 If desired proceed to MODIFICATION Otherwise proceed to CABLE MANAGEMENT for display with RECESSED mounting holes or to e DISPLAY INSTALLATION for all other display configurations 11 Model F Series Installation Instructions MODIFICATION If desired each arm assembly 10 may be modified to prevent movement of the outer arm relative to the inner arm without loosening the adjustment screw NOTE Spacer shipped configuration will allow limited movement of outer arm relative to inner arm dependent upon tension of screw Washer 80 will lock arms together See ADJUSTMENT for detail 1 Using 3 16 hex key loosen screw until nut can be removed See Figure 19 Retain nut Screw and washers may remain in outer arm Screw amp washers Ta db CD Figure 19 Multi Dual Arm Modification 2 Lift outer arm from pin with screw and washers and place on protective surface Remove spacer from pin See Figure 19 4 Install washer 80 on pin See Figure 19 Re install outer arm with screw and washers on pin See Figure 19 6 Insert and hold nut in lower bore of inner arm See Figure 19 7 Tighten screw as required using 3 16 hex key See Figure 19 8 Proceedto CABLE MANAGEMENT for display with REC2. Centris Bracket Figure 10 Single Display Flush Mount 5 Using Phillips screwdriver install two remaining screws 20 through the lower mounting holes in Centris bracket into the display 6 Tighten all four screws 20 Do not overtighten 7 FCY 210 220 Only Repeat Steps 1 6 for second display 8 Proceed to CABLE MANAGEMENT RECESSED MOUNTING HOLES 1 Verify that you have the following parts Item Description Qty 10 MOUNT F Series 1 20 SCREW Phillips Pan Machine M4 x 20mm 4 30 SCREW Phillips Pan Machine M4 x 30mm 4 40 SPACER Nylon 3 8 long 4 50 SPACER Nylon 3 4 long 4 2 Ensure Centris bracket is able to swivel and tilt easily yet still be tight enough to hold display in desired position Adjust as required before proceeding See ADJUSTMENT for detail 3 Carefully place display face down on protective surface 4 Determine depth of recessed mounting holes relative to back surface of display against which Centris head will contact 5 Select proper length spacer and screw from table below NOTE All spacers used should be the same length If the recess depths result in multiple spacer lengths then select the longer spacer IF recess DEPTH is THEN use spacer AND screw 3 8 or less 40 3 8 long 20 M4 x 20mm More than 3 8 up to 150 3 4 long 30 M4 x 30mm and including 3 4 6 Place the four selected spacer
3. Installation Instructions Model F Series DISPLAY INSTALLATION SINGLE DISPLAY AND FCY 210 220 NOTE If you are installing DUAL TRIPLE displays FMA 220 320 then proceed to page 9 The mounting holes on the back of your display will either be flush with the back surface or recessed into the back surface Refer to the applicable installation procedure FLUSH MOUNTING HOLES 1 Verify that you have the following parts Item Description Qty 10 MOUNT F Series 1 20 SCREW Phillips Pan Machine M4 x 12mm 4 A CAUTION Using screws of improper size may damage your display Proper screws will easily and completely thread into display mounting holes CAUTION Inadequate thread engagement in display may cause display to fall Back out screws ONLY as necessary to allow installation of Centris bracket 2 Ensure Centris bracket is able to swivel and tilt easily yet still be tight enough to hold display in desired position Adjust as required before proceeding See ADJUSTMENT for detail 3 Using Phillips screwdriver carefully install two screws 20 into the upper mounting holes on the display Thread screws completely into display then back out 3 complete turns 4 Pick up and align display so that screws 20 installed on the back of the display in the previous step fit into the mounting holes on the Centris bracket rotate the bracket as required See Figure 10 Lower the display firmly into place
4. and including 3 4 5 Place the four selected spacers over each of the mount holes on the back of the display 6 Place the Centris head dual knob assembly onto the spacers aligning the mounting holes on the Centris bracket with the holes in the spacers See Figure 13 10 Centris A Bracket a j lt a 20 or 30 4 places 40 or 50 4 places Figure 13 Dual Triple Display Recessed Mount A CAUTION Using screws of improper size may damage your display Proper screws will easily and completely thread into display mounting holes 7 Using Phillips screwdriver install four selected screws through the mounting holes in Centris bracket through the spacers into the display See Figure 13 Tighten all four screws Do not overtighten 8 Proceed to ARRAY ASSEMBLY Model F Series Installation Instructions ARRAY ASSEMBLY DUAL TRIPLE DISPLAY FMA 220 320 ONLY 1 Verify that you have the following parts Insert and hold nut 80 into lower mount arm bore See Figure 14 Insert screw 20 or 30 as applicable through washer 50 washer 40 washer 50 array 10 array mount arm assembly and into nut 80 See Figure 14 Tighten screw as reguired using 3 16 hex key Slide the Centris head dual knob assembly onto the array 10 See Figure 15 Ensure both the top and the bottoms of the Centris head are engaged into the corresponding slo
5. Table 1 Mounts MODEL SUPPORTING NO OF ADJUSTABLE MAX MIN DISPLAYS STRUCTURE MOUNTING HEIGHT ARMS INCHES DEPTH INCHES FWP 110 Single Wall None No None 2 9 40 FWV 110 Single Wall Single Yes 13 2 2 25 FWS 110 Single Wall Single No 9 5 2 2 40 FWG 110 Single Wall Dual Yes 19 5 2 2 25 FWD 110 Single Wall Dual No 16 2 2 40 FWB 110 Single Wall Triple Yes 26 2 2 25 FCV 110 Single Desk Single Yes 13 5 2 2 25 FCS 110 Single Desk Single No 10 2 2 40 FCG 110 Single Desk Dual Yes 20 2 2 25 FCD 110 Single Desk Dual No 16 5 2 2 40 FCB 110 Single Desk Triple Yes 26 5 2 2 25 FPP 110 Single Pole None No None 2 2 40 FPS 110 Single Pole Single No 9 5 2 2 40 FPD 110 Single Pole Dual No 16 2 2 40 FGL 110 Tray Desk Single Yes 29 5 14 18 FGL 220 Single Tray Desk Dual Yes 19 5 14 40 total FCY 210 Dual Desk Multi Dual Yes one arm 20 2 2 40 FCY 220 Dual Desk Multi Dual Yes two arms 20 2 2 40 Model F Series Installation Instructions MOUNT INSTALLATION INSTALLATION TO WALL 1 Verify that you have the following parts Item Description Qty 10 MOUNT Wall F Series 1 20 BRACKET Wall 1 30 SCREW Phillips Pan Sheet Metal 10 x 2 1 2 2 40 WASHER Flat Machine Screw 10 2 2 Determine location for mount keeping in mind display size extension height adjustment if applicable and pitch roll requirements Bracket 20 MUST be in
6. of cover 10 or screws 20 5 Carefully insert cables in cavity located in lower portion of mount arm See Figure 22 6 Using Phillips screwdriver install cover 10 with two screws 20 Cable Path typical Figure 22 Static Arm Cable Path NOTE Installation is complete 13 Model F Series Installation Instructions ADJUSTMENT ARM PIVOT SWING CAUTION If washer 80 has been used to assemble FCY 210 220 arms then forced movement of arms without loosening screw 30 will damage arm and or Y connector See Figure 17 See Figure 19 1 Using 3 16 hex key slightly loosen or tighten the adjustment screw s as necessary See Figure 23 Adjustment Screws Figure 23 Pivot Swing Arm Adjustment HEIGHT ADJUSTABLE IF APPLICABLE 1 Using 5 32 hex key slightly loosen or tighten the adjustment screw as necessary See Figure 24 e If display settles on its own then rotate adjustment screw counterclockwise towards the symbol e If display rises on its own then rotate adjustment screw clockwise towards the symbol NOTE It may be necessary to raise or lower the height adjustable arm to expose the adjustment screw Adjustment Screw Figure 24 Height Adjustable Arm Adjustment 14 CENTRIS HEAD SINGLE DISPLAY AND FCY 210 220 1 If previously attached disconnect cables from display then remove display 2 Using Phillips
7. ANAGEMENT e FCY 210 220 Proceed to MULTI DUAL ARM ASSEMBLY e ALL other display configurations Proceed to DISPLAY INSTALLATION HOLE GROMMET INSTALLATION 1 Using 2 5mm hex key remove and retain baseplate and three attach screws from bottom of mount 10 See Figure 6 Attach Screws 9 3 places H Baseplate Baseplate b Nut Figure 6 Baseplate 2 Using 3 16 hex key remove clamp adjustment screw washer and clamp See Figure 7 Retain clamp adjustment screw and washer for later use NOTE Clamp will not be used for Hole Grommet Installation Model F Series Installation Instructions lt a Clamp Adjustment Screw Figure 7 Remove Clamp Adjustment Screw 3 Using 2 5mm hex key re install baseplate with three retained attach screws Ensure baseplate nut faces interior of mount See Figure 6 Tighten securely IMPORTANT IF you will be installing a SINGLE display including FCY 210 220 with RECESSED mounting holes then proceed to DISPLAY INSTALLATION before continuing with this mount installation procedure 4 From below desk insert retained clamp adjustment screw and washer through bracket 20 and up through hole in desk See Figure 8 Using 3 16 hex key thread screw into baseplate nut but do not tighten completely at this time Baseplate Nut P Desk ta lt a Washer lt a Clamp Adjustment Sc
8. ESSED mounting holes or to DISPLAY INSTALLATION for all other display configurations 12 Installation Instructions Model F Series CABLE MANAGEMENT Ite 10 20 m Description COVER Arm SCREW Phillips Flat Machine 8 32 x 3 8 Qty 1 per arm 2 per arm 30 WRENCH Hex 3 32 provided 1 1 2 Open the cable management bracket by sliding it NOTE If necessary cable management bracket attach Attach all cables to display towards the edge of the arm See Figure 20 screws may be loosened using hex key 30 Attach Screws OPEN Position CLOSED Position ioh View from Bottom SN 3 Carefully insert cables into bracket See Figure 21 Figure 20 Height Adjustable Arm Cable Management Bracket A CAUTION Ensure that adequate cable slack exists for movement of display and that cables will not be pinched when bracket is closed Cable Management Bracket in open position NOTE Display not shown for clarity Cable Path typical Figure 21 Height Adjustable Arm Cable Path 4 Close cable management bracket by sliding it back towards the centerline of the arm See Figure 20 NOTE If necessary cable management bracket attach screws may be tightened using hex key 30 CAUTION Ensure that adequate cable slack exists for movement of display and that cables will not be pinched by installation
9. INSTALLATION INSTRUCTIONS Small Flat Panel Mounts Model F Series This Instruction Manual covers most of the F Series wall and desk mounts as well as selected F Series pole mounts NOTE Some F Series mounts e g Table Pole and F Series accessories have separate Instruction tz Manuals See Specifications on page 3 for a complete list of models covered by this Instruction Manual laptop tray is being installed complete all reguired installation procedures within this document prior to installing the accessory F Series Mounts Examples IMPORTANT If an accessory such as an optional NA BEFORE YOU BEGIN WARNING It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty e If you have any questions about this these instructions or your specific installation contact Chief Manufacturing at 1 800 582 6480 or 952 894 6280 DISCLAIMER CSAV Inc and its affiliated corporations and subsidiaries collectively CSAV intend to make this manual accurate and complete However CSAV makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the
10. MOUNT Desk F Series 1 30 SCREW Button Head Cap 5 16 18 x 4 2 40 WASHER 5 16 UHMW plastic 2 50 WASHER 5 16 Stainless Steel 4 60 PIN 2 70 SPACER UHMW plastic 2 80 WASHER Lock External Tooth 5 8 4 90 NUT Nylok 5 16 18 2 2 Insert pin 60 into Y connector upper bore in mount 20 See Figure 17 NOTE All parts same for both sides NOTE FCY 220 shown FCY 210 similar Figure 17 Multi Dual Arm Assembly 3 Install spacer 70 or washer 80 as desired on pin 60 See Figure 17 NOTE Spacer 70 will allow limited movement of arm assembly 10 relative to Y connector dependent upon tension of screw 30 Washer 80 will lock arm assembly 10 to Y connector See ADJUSTMENT for detail 4 Insert arm assembly 10 on pin 60 See Figure 17 5 While holding nut 90 in lower bore of Y connector insert screw 30 through washer 50 washer 40 washer 50 arm assembly 10 and Y connector into nut 90 See Figure 17 Loosely install screw 30 using 3 16 hex key CAUTION Improper positioning of arm assembly 10 may result in failure of mount and subsequent damage to displays Do NOT position either arm assembly 10 in gray shaded area 6 Position arm assembly 10 within UNSHADED area as shown See Figure 18 Using 3 16 hex key tighten screw 30 as required to maintain position DO NOT POSITION EITHER ARM ASSEMBLY IN GRAY SHADED AREA
11. all components does not exceed the maximum support weight as stated in the Specifications on page 3 WARNING Allowing any part of your body or component cables to be caught between movable parts can result in serious personal injury or damage to equipment A CAUTION Overtightening fasteners may result in improper operation excessive wear or damage to equipment and or voiding of factory warranty CONTENTS TOOLS REQUIRED FOR AINSTALLATION aa a u 2 SPEGCIFIGATIONS boob ao Saone eae sa A a Aula k T 3 MOUNT INSTALLATION 2 sccecha ati atin daniel Ane iis sie en O 4 DISPLAY INSTALLATION ie tenet aries a ete ited ee teen abhi aa 7 ARRAY ASSEMBLY DUAL TRIPLE DISPLAY FMA 220 320 ONLY eee sena r rasar one n an 10 MULTI DUAL ARM ASSEMBLY FCY 210 220 ONLY u eee eee eee eee RE nn 11 CABLE MANAGEMENT oo dan k aiti b h A venue v hi i lv li NERD AAA NANNA DENA saan 13 ADIUSTMEN ii op a o noh ead ach oder skar cea pc doo zh uo dicta pa pata o ere nad A sd S A ak S t s k 14 TOOLS REQUIRED FOR INSTALLATION e Phillips Screwdriver 1 and 2 Drill All Wall Mounts e 1 8 Drill Bit All Wall Mounts e 2 5mm Hex Key approximately 3 32 provided with Desk Mounts e 5 32 Hex Key provided with applicable F Series mounts e 3 16 Hex Key provided with all F Series mounts NOTE Other tools may be required depending on your method of installation Installation Instructions Model F Series SPECIFICATIONS
12. installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind CSAV makes no representation of warranty expressed or implied regarding the information contained herein CSAV assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document CHIEF MANUFACTURING INC 8832 000173 RevB TAY i 1 800 582 6480 952 894 6280 FAX 952 894 6918 2007 Chief Manufacturing 8401 EAGLE CREEK PARKWAY STE 700 www chiefmfg com SAVAGE MINNESOTA 55378 USA 03 07 Model F Series Installation Instructions A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of
13. is bracket with the mounting holes on the display CAUTION Using screws of improper size may damage your display Proper screws will easily and completely thread into display mounting holes 4 Using Phillips screwdriver install four screws 20 through the mounting holes in Centris bracket into the display See Figure 12 Tighten all four screws 20 Do not overtighten 1 t 20 4 places Centris U Bracket SS Item Description Qty 20 SCREW Phillips Pan Machine M4 x 20mm 4 per head 30 SCREW Phillips Pan Machine M4 x 30mm 4 per head 40 SPACER Nylon 3 8 long 4 per head 50 SPACER Nylon 3 4 long 4 per head 2 Carefully place display face down on protective surface 3 Determine depth of recessed mounting holes relative to back surface of display against which Centris head dual knob assembly will contact 4 Select proper length spacer and screw from table below NOTE All spacers used should be the same length If the recess depths result in multiple spacer lengths then select the longer spacer Figure 12 Dual Triple Display Flush Mount 5 Proceed to ARRAY ASSEMBLY RECESSED MOUNTING HOLES 1 Verify that you have the following parts Item Description Qty 10 CENTRIS HEAD Dual Knob Assembly 2 3 IF recess DEPTH is THEN use spacer AND screw 3 8 or less 40 3 8 long 20 M4 x 20mm More than 3 8 up to 50 3 4 long 30 M4 x 30mm
14. rew Figure 8 Desk Mount Hole Installation 5 Center mount 10 over hole Using 3 16 hex key securely tighten screw 6 Drop screw 30 into open unused clamp adjustment hole on top of mount for appearance only 7 If you are installing SINGLE display with RECESSED mounting holes Proceed to CABLE MANAGEMENT e FCY 210 220 Proceed to MULTI DUAL ARM ASSEMBLY e ALL other display configurations Proceed to DISPLAY INSTALLATION INSTALLATION TO POLE 1 Verify that you have the following parts Item Description Qty 10 MOUNT Pole F Series 1 20 CLAMP Back 1 30 SCREW Button Head Cap 1 4 20 x 1 1 8 3 IMPORTANT IF you will be installing a SINGLE display with RECESSED mounting holes then proceed to DISPLAY INSTALLATION before continuing with this mount installation procedure 2 Determine approximate location for mount keeping in mind display size extension height adjustment if applicable and pitch roll requirements 3 Place mount 10 against pole with clamp 20 on opposite side of pole See Figure 9 Using 5 32 hex key loosely assemble with screws 30 a egy Figure 9 Pole Mount Installation 4 Position mount at desired height and orientation Tighten screws 30 securely 5 Proceed to CABLE MANAGEMENT for SINGLE display with RECESSED mounting holes or to DISPLAY INSTALLATION for all other display configurations
15. s Model F Series INSTALLATION TO DESK Two installation options exist Edge Installation Hole Grommet Installation requires 3 8 to 3 diameter hole and access to the bottom of the desk ASSEMBLY 1 Verify that you have the following parts Item Description Qty 10 MOUNT Desk F Series 1 20 BRACKET Grommet 1 30 SCREW Button Head Cap 5 16 18 x 4 1 40 BUMPER Adhesive 6 2 Determine approximate location for mount keeping in mind display size extension height adjustment if applicable and pitch roll requirements 3 Peel backing from adhesive bumpers 40 and attach to bottom of mount 10 See Figure 4 NOTE One extra bumper 40 included for convenience OQO 40 5 places Figure 4 Install Bumpers EDGE INSTALLATION IMPORTANT IF you will be installing a SINGLE display including FCY 210 220 with RECESSED mounting holes then proceed to DISPLAY INSTALLATION before continuing with this mount installation procedure NOTE Bracket 20 and screw 30 are not used in this installation 1 Slip mount 10 over edge of desk so that clamp fully contacts desk edge Using 3 16 hex key securely tighten clamp adjustment screw See Figure 5 Clamp Adjustment Screw of Desk Clamp Figure 5 Desk Mount Edge Installation 2 Ifyou are installing e SINGLE display with RECESSED mounting holes Proceed to CABLE M
16. s over each of the mount holes on the back of the display 7 Pick up and orient the mount 10 so that the mounting holes in the Centris bracket are aligned with the holes in the spacers rotate the bracket as required See Figure 11 Model F Series Installation Instructions Figure 11 Single Display Recessed Mount CAUTION Using screws of improper size may damage your display Proper screws will easily and completely thread into display mounting holes 8 Using Phillips screwdriver install four selected screws through the mounting holes in Centris bracket through the spacers into the display See Figure 11 Tighten all four screws Do not overtighten 9 FCY 210 220 Only Repeat Steps 1 6 for second display 10 Continue with MOUNT INSTALLATION Installation Instructions Model F Series DUAL TRIPLE DISPLAY FMA 220 320 and KGL 220 ONLY The mounting holes on the rear of your display will either be flush with the rear surface or recessed into the rear surface Refer to the applicable installation procedure FLUSH MOUNTING HOLES 1 Verify that you have the following parts Item Description Qty 10 CENTRIS HEAD Dual Knob Assembly 2 3 20 SCREW Phillips Pan Machine M4 x 12mm 4 per head 2 Carefully place display face down on protective surface 3 Place the Centris head dual knob assembly onto the back of the display aligning the mounting holes on the Centr
17. screwdriver slightly loosen or tighten the adjustment screw as necessary See Figure 25 Adjustment Screw Figure 25 Single Display Adjustment 3 Install mount and then display cables See DISPLAY INSTALLATION DUAL TRIPLE DISPLAY FMA 220 320 ONLY 1 LATERAL POSITION ON ARRAY e Using your fingers slightly loosen adjustment knob A See Figure 26 e Slide display to desired position e Using your fingers tighten adjustment knob A Figure 26 Dual Triple Display Adjustment 2 PITCH YAW ROLL e Using your fingers slightly loosen adjustment knob B See Figure 26 e Adjust display as desired e Using your fingers tighten adjustment knob B Installation Instructions Model F Series 15 Po K Os CONSUMER
18. stalled into wood stud 3 Using bracket 20 as a template drill two 1 8 diameter pilot holes through top and bottom holes of bracket 20 into wall structure See Figure 1 OSS Figure 1 Install Wall Bracket 4 Using Phillips screwdriver install screws 30 through washers 40 bracket 20 and drywall into wood stud See Figure 1 Ensure bracket 20 is vertical then tighten screws 30 IMPORTANT Overtightening screws 30 may cause bracket 20 to compress into soft wall surface resulting in difficult mount installation or improper engaging of set screw in step 6 IMPORTANT IF you will be installing a SINGLE display with RECESSED mounting holes then proceed to DISPLAY INSTALLATION before continuing with this mount installation procedure 5 Insert top of mount 10 over lip on top of bracket 20 See Figure 2 Swing mount 10 down flush against wall NOTE FWS 110 shown other wall mounts similar Figure 2 Install Wall Mount 6 Tighten set screw using 5 32 hex key See Figure 3 Ensure set screw engages back side of bracket 20 to properly secure mount 20 Set Screw NOTE FWS 110 shown other wall mounts similar Figure 3 Tighten Set Screw 7 Proceed to CABLE MANAGEMENT for SINGLE display with RECESSED mounting holes or to DISPLAY INSTALLATION for all other display configurations Installation Instruction
19. ts in the array 10 Item Description 10 ARRAY 20 SCREW Button Head Cap 5 16 18 x 4 1 Used for Pivot Swing Arm 30 SCREW Button Head Cap 5 16 18 x 5 1 Used with Height Adjustable Arm 40 WASHER 5 16 UHMW plastic 1 50 WASHER 5 16 Stainless Steel 2 60 PIN 1 70 SPACER UHMW plastic 1 80 NUT Nylok 5 16 18 1 90 SCREW Button Head Cap 1 4 20 x 1 2 2 100 NUT Square Machine Screw 1 4 20 2 2 Install pin 60 and spacer 70 into upper mount arm bore See Figure 14 20 or 30 20 shown 30 similar Figure 14 Assemble Array 3 Install array 10 onto pin 60 See Figure 14 10 Centris Head NOTE Dual display shown triple display similar Figure 15 Install Display Position the displays as desired and tighten the Centris head knob closest to the array 10 See ADJUSTMENT for additional information Using 5 32 hex key install screw 90 and nut 100 on each end of the array 10 to prevent displays from accidently sliding off See Figure 16 NOTE Left side shown right side similar Figure 16 Install End Locks 9 Proceed to CABLE MANAGEMENT Installation Instructions Model F Series MULTI DUAL ARM ASSEMBLY FCY 210 220 and FGL 220 ONLY BASIC ASSEMBLY 1 Verify that you have the following parts Item Description Qty 10 ARM ASSEMBLY F Series 2 20
Download Pdf Manuals
Related Search