Chief KTA1004B mounting kit
Contents
1. A over desired mounting location on desk See Figure 2 6 If there is not enough clearance behind the desk for the device to clear remove the bottom portion of the desk clamp by using 5 32 hex key D to remove 2 connecting screws See Figure 2 7 Reinstall bottom portion of the desk clamp if necessary by reinstalling 2 connecting screws underneath desk See Figure 2 6 ao behind desk Figure 2 8 clamp screw until the clamp is secured to the desk as tightly as possible See Figure 3 Figure 3 WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the KTA 1004 desk clamp up to and including the display projector does not exceed the weight limits of the pole mount attached to the desk clamp Install mount to mounting pole according to corresponding installation manual for the specific mount to be attached to mounting pole 5 KTA 1004 Installation Instructions Installation Instructions KTA 1004 KTA 1004 Installation Instructions TAN USA International A 8401 Eagle Creek Parkway Savage MN 55378 E P 800 582 6480 952 894 6280 F 877 894 6918 952 894 6918 Our Mounts Your Vision Europe A Fellenoord 130 5611 ZB EINDHOVEN The Netherlands P 31 0 40 2668620 F 31 0 40 26686152. A Room 24F Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA ARI Th Ap zs 27 RAN ELS aR A RO Ar P 486 755 8996 9226 2008 Milestone AV Technologies F 486 755 8996 9217 RP www chiefmfg com 7 10 08 e b SE consumer Chief Manufacturing a division of Milestone AV Technologies Asia Pacific 8834 000007
3. INSTALLATION INSTRUCTIONS N Q N d DESK CLAMP FOR POLE MOUNTS CHIEF KTA 1004 Our Mounts Your Vision KTA 1004 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions DIMENSIONS WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of f
4. actory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Failure to keep all mounted equipment directly above the desk surface at all times can result in serious personal injury or damage to equipment All mounted equipment must remain directly above the surface of the desk in order to ensure and maintain a stable mount WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the KTA 1004 desk clamp up to and including the display projector does not exceed the weight limits of the pole mount attached to the desk clamp je 3 63 5 50 NOTINCLUDED i 3 93 gt e 50 MIN 3 00 MAX Installation Instructions KTA 1004 LEGEND Tighten Fastener Apretar elemento de fijaci n Bef
5. estigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con lapiz Stiftmarkierung Marcar com lapis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a m o A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option d y 4 Of 2 Hex Head Wrench Llave de cabeza hexagonal 2 9 9 I CG Sechskant
6. schl ssel Chave de sextavada Chiave esagonale Zeskantsleutel Cl a t te hexagonale Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguran a Chiave di sicurezza Veiligheidssleutel Cl de s curit Installation Instructions KTA 1004 TOOLS REQUIRED FOR INSTALLATION included 5 32 7 32 included 6 C 1 3 8 16 x 1 Installation Instructions KTA 1004 INSTALLATION NOTE In order to reduce the chance of scratching to the mounting surface bumpers may be installed However installation of bumpers is optional 1 Remove adhesive from underside of bumpers B 2 Attach bumpers B to underside of desk clamp See Figure 1 mounting pole N lt view from bottom Figure 1 3 Use 7 32 hex key E to install 3 8 16 x 1 flat head cap screw C through the opening on top of desk clamp A and into bottom of mounting pole not included See Figure 1 4 Determine the location where desk clamp will be mounted WARNING Failure to keep all mounted equipment directly above the desk surface at all times can result in serious personal injury or damage to equipment All mounted equipment must remain directly above the surface of the desk in order to ensure and maintain a stable mount 5 Place desk clamp
Download Pdf Manuals
Related Search