Chief SL236FD project mount
Contents
1. DIMENSIONS MILLIMETERS INCHES SL236 Installation Instructions INSTALLATION REQUIREMENTS NOTE Throughout this document reference to SL236 refers to both SL236FD and SL236SP models The SL236 has been designed to be mounted recessed into a ceiling Power Requirements The SL236 requires 120VAC 60 Hz and 12 amps power to operate IMPORTANT Installation and maintenance of this product must be completed by a qualified service technician Pre Test Lift before Installation 1 Carefully inspect the SL236 for any shipping damage If any damage is apparent do NOT continue with the installation Instead contact Chief for further instructions 2 Attach supports not provided to the top of lift See Figure 1 Supports Figure 1 3 Suspend the lift at least 3 1 2 ft above a surface from a suitable structure such as saw horses ladders or tables 4 Remove and save two screws holding side electrical cover in place See Figure 2 5 Remove electrical cover See Figure 2 External wiring terminal Electrical Cover Figure 2 6 Place the jumper wire E on the external wiring terminal contacts labeled 2 and 5 and wire the push button assembly B to contacts 1 red and 6 black See Figure 3 7 Plugin the SL236 test cord See Figure 2 Place jumper wire E 2 and 5 Wire push button assembly B 1 red 6 black Figure 3 NOTE See Fi2. INSTALLATION INSTRUCTIONS SMART LIFT Electric Ceiling Lift This device complies with part 15 of the FCC rules Operation is subject to the following 2 conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television communications However there is no guarantee that the interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment to an outlet on a circuit other than that to which the receiver is connected Consult the dealer or and experienced radio TV technician for help Our Mounts Your Vision SL236 Installation Instru
3. e Adjust and tighten nuts on bracket See Figure 16 Figure 16 Routing Cables CAUTION Do NOT attach cables to lower lifting arms or sides of projector bracket Damage may result when lift is raised Lower SL236 to service position Route and secure electrical and video cables using installed cable clips See Figure 17 Remove nut and open cable clip Route cable through clip Close cable clip and fasten with nut Included mounting tabs F and cable ties C may also be used for securing cables CAUTION SHOCK INJURY OR DAMAGE TO EQUIPMENT IS POSSIBLE Avoid placing cables near moving parts and pinch points to avoid damage to the cables Ensure there is enough slack in the cables to allow for up and down movement of the lift 11 SL236 Installation Instructions Cable clips slack for movement Figure 17 Connecting Control Wiring ordinances ull WARNING All wiring should be performed following all local codes and 1 Unplug the SL236 s power cord used for testing 2 Remove the jumper wire E and supplied push button B wiring previously installed in the Pre Test Lift before Installation section from the external terminal block See Figure 3 3 Connect control wiring following instructions included with the third party automation and control equipment and user supplied switching devices and information in Table 1 Wiring Table
4. Internal Terminal Descriptions 14 Internal External Wiring Terminal DOS CPO iiic raria nennen 15 Installation Instructions SL236 DIMENSIONS 520 7 260 4 ard SL 236FD 10 25 Es gt Sa i J 4 732 8 584 2 28 85 x 698 5 MAXIMUM AVAILABLE SPACE FOR 27 50 PROJ ECTOR AND EQUIPMENT HxWxD 9 25 x 20 50 x 22 75 INCHES 235 0 x 520 7 x 577 9mm y W Y lt 635 0 25 00 669 3 gt 65 16 5 26 39 19 1 75 280 9 11 06 1 06 26 9 914 4 36 00 MAX DIMENSIONS MILLIMETERS 606 3 INCHES 23 87 SL 236SP 520 7 20 50 260 4 0 25 Am i i SBS 719 1 K 4 34 28 31 584 2 23 00 Pasa MAXIMUM AVAILABLE SPACE FOR l PROJ EC TOR AND EQUIPMENT Y Y HxWxD 9 25 x 20 50 x 22 75 INC HES 235 0 x 520 7 x 577 9mm 638 0 65 16 5 t 7 2 amp 12 I 1 06 26 9 LJ dba 311 2 11 12 E 3 12 25 E E a Le 107 27 2 41 10 4 HEIG HTTO ALLOW FOR THE ROOM THE SLB BRAC KET WILL C ONSUM E EJ E S kr 914 4 36 00 MAX nre eg Y CURRENT 9 26 235 2 ERES MAX9 91 251 7 jp MIN 7 78 197 6 z 906 6 REMEMBER TO ADD 375 TO 1 00 606 6 9 5 TO 25 4mm TO THE MAX 23 88 9 91 251 7mm OF YOUR PROJ ECTOR 633 5 24 94
5. Other Environmental Air Space in Accordance with Section 300 22 C of the National Electrical Code When using an electrical mounting system basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT A DANG E R TO REDUCE THE RISK OF ELECTRIC SHOCK 1 Always turn off power at source before cleaning A WARNING TO REDUCE THE RISK OF BURNS FIRE ELECTRIC SHOCK OR INJURY TO PERSONS e Always turn off power at source before putting on or taking off parts e Use this mounting system only for its intended use as described in these instructions Do NOT use attachments not recommended by the manufacturer Never operate this mounting system if it has a damaged test cord or test plug If it is not working properly during testing return the mounting system to a service center for examination and repair e Keep the test power cord away from heated surfaces e Never operate the mounting system with the air openings blocked Keep the air openings free of lint hair and the like e Never drop or insert any object into any opening Do not use outdoors unless marked for outdoor use Route cords and cables as shown in the installation instructions Todisconnect turn all controls to the off position then turn off power at source A WARN NG RISK OF ELECTRIC SHOCK Connect this mounting system to a properly grounded outlet only See Grounding Instructi
6. There are no size limitations for the wood framework on the other three sides of the SL236FD Mounting Tabs e gt Mounting NN Tab SI N s RON E 7 Figure 10 CAUTION The lift MUST be installed square and parallel Do NOT stress or bend the lift during installation 2 Use the provided push button B to operate the SL236FD up and down ensuring that all clearances are adequate Installing Projector on SL236 NOTE The projector is secured from the top by an SLB bracket a Listed accessory which is not included 1 Attach the SLB bracket to the projector using the hardware and instructions included with the bracket SL236 Installation Instructions Press in end tabs on both ends of yaw adjustment bracket and lock into place See Figure 11 Remove the yaw adjustment bracket from the SL236 by lifting up See Figure 11 Bracket e Yaw Adjustment 4 Figure 11 Place the yaw adjustment bracket over the studs on the SLB bracket selecting the set of holes that best centers the projector weight See Figure 12 Install thumb nuts to secure yaw adjustment bracket to SLB bracket with projector Reinstall yaw adjustment bracket with projector to SL236 by setting it in place and releasing tabs at each end of yaw adjustment bracket See Figure 12 SLB Bracket appearance varies 10 Figure 12 Adjustments 1 TRAVEL SHOW ADJUSTMENT A
7. 24 cmm o AC common baw Jens EEE 12 VOLT DC amp or used for initiating specific functions Initiates movement if lift is static or stops movement if lift is in motion Direction of travel will be opposite ISOLATED EXTEND RETRACT of last direction of travel Operating range is 5 30 Volts AC or DC Used in conjunction with Extend Retract when using NOT TO BE USED AS GROUND FOR FUNCTION OTHER THAN ISOLATED EXTEND RETRACT an external power source to initiate movement EXTEND RETRACT TERMINAL 5 When control senses voltage unit will extend When 7 ISOLATED VOLTAGE SENSE control senses cessation of voltage unit will retract Operating range is 5 30 Volts AC or DC Used in conjunction with Voltage Sensor when using NOT TO BE USED AS GROUND FOR FUNCTION OTHER THAN ISOLATED VOLTAGE SENSE an external power source to Initiate movement VOLTAGE SENSOR TERMINAL 7 Extends unit to maximum limit bypassing normal use travel setting Often used for servicing projectors in GE EXTEND ceiling lifts Feature not available on all models Ground he connected to ground initiating any other function Se AAA RETRACT momentarlally connected to ground initiating any other function 13 GROUND JGrund Immediately reverses direction of travel when ispemecrrmon 00 w gmsiwiewiikranaw O monenarysonedientegeunieremrmode RETRACT ERROR triggered while unit is retracting momentary connection to ground initiates error mod
8. CAUTION Do not overadjust exceed maximum travel length To adjust the travel of the lift mechanism insert a Phillips screwdriver into the access hole found at the left rear corner of the lift NOTE The access hole may be covered by ceiling tile in the SL236SP model Shorten travel by turning adjustment screw clockwise one or two turns Check for desired travel and repeat as necessary See Figure 13 Lengthen travel by turning the adjustment screw counter clockwise one or two turns Check for desired travel and repeat as necessary See Figure 13 Front of unit 1 Travel adjust access hole SL236SP shown SL236FD similar Figure 13 Installation Instructions SL236 2 FORWARD BACKWARD and PITCH e Toshift projector backward or forward or up or down loosen the nuts on each end of the yaw adjustment bracket See Figure 14 Move mounting bracket forward or backward or up or down as required The bracket must be adjusted forward backward equally Tighten nuts See Figure 14 Figure 14 3 YAW Rotation Adjust one or the other side of the yaw adjustment bracket backward or forward by loosening two nuts on each side See Figure 15 Adjust bracket as required Tighten nuts See Figure 15 Figure 15 4 ROLL Horizontal Tilt Shift bracket up or down in the side holes on one side or the other by loosening nuts
9. E This unit was designed to have conduit run directly into the back of the interior junction box NOTE If installing the SL236 in a drywall ceiling remove the outside terminal block and cover with plate D using four 6 32 x 3 16 Phillips pan head screws G Wiring Options NOTE Referto the Table 1 Wiring Table and See Figure 18 for information on all wiring options NOTE Refer to Table 2 InternalTerminal Descriptions and See Figure 19 for terminal descriptions functions and wiring options Installation Instructions SL236 Table 1 WIRING TABLE Accessory MProduct Pushbutton Supplied on some models Momentary SPST SL 236 Internal 2 24V AC Comm SL 236 External 2 24V AC Comm 6 Extend Retract Comm 5 Extend Retract Comm Jumper1 amp 5 12 retract 11 extend N A Jumper1 amp 6 3 retract 4 extend N A N A N A N A N A 12V Trigger will actually work with 5 30V AC or DC 12V Ground N A 13 ground 7 trigger 8 trigger 4 12V DC N A 9 ground 10 12V DC 3 ground 9 ground radio power Red 12 retract 11 extend 9 service 13 ground 1 24V AC 3 retract 4 extend 11 service 9 ground 1 24V AC relay Black 6 Extend Retract Comm 5 Extend Retract Comm Low Voltage Wall Switch or Relay Control 24V White Other Up Down 2 24V AC C
10. LLATION CAN LEAD TO LIFT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installers responsibility to make certain the structure to which the lift is being mounted is capable of supporting five times the weight of the lift and all attached equipment Reinforce the structure as required before installing the lift WARNING The following instructions assume a suitable mounting structure and surface exists prior to installation and all power and signal wires and cables have been properly installed Installing in a Suspended Ceiling SL236SP Only NOTE The SL236SP may be suspended from three 3 8 in diameter x 8 in length minimum Grade 2 or better threaded rods not provided which are secured to a 1 5 8 x 1 5 8 12 ga metal framing channel spanning a maximum of 5 feet not provided by Grade 2 or better 3 8 channel nuts not provided 1 Remove and save nuts attaching guide wires to two corners of ceiling panel See Figure 5 Ceiling Panel Figure 5 SL236 Installation Instructions 2 Pull down on each corner of ceiling panel to remove ceiling panel clips from rectangular holes See Figure 5 3 Install the SMA651 optional accessory at this time if applicable following instructions included with the kit 4 QCutthe ceiling grid to fit the perimeter of the SL236SP 5 Place SL236SP onto threaded rods inserting the rods into the three slots on top of the SL236SP housi
11. NOTE Any knockouts removed in the SL236 must be replaced with a supplied rubber grommet H 12 4 Feedthe video and or communications cables through the knockout in the rear or top of the lift and connect it to the projector NOTE Ensure there is enough slack in the cables to allow for up and down movement of the lift 5 Secure cables as necessary using supplied mounting pads F and cable ties C A CAUTION KEEP SL236 OPEN WHILE PROJECTOR IS RUNNING OR IN COOLING MODE Premature bulb failure or damage to electrical components may occur if lift closes NOTE If SL236 is cycled up and down repeatedly the motor s thermal overload protection will stop operation Operation will resume when the thermal overload resets usually within 3 to 5 minutes Connecting to Power Supply IMPORTANT This product must be connected to a grounded metal permanent wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the product WARNING FAILURE TO DISCONNECT AND TERMINATE POWER LEADS PROPERLY MAY RESULT IN PERSONAL INJURY OR EQUIPMENT DAMAGE Licensed electrician must disconnect and terminate the leads to the power cord receptacle and must hard wire the SL236 to a 12 amp power source 4 1 Disconnect and remove power inlet from interior junction box 2 Hardwire unit to a 120V 60Hz 12 amp power source NOT
12. ch guide wires two places to SL236SP using nuts removed earlier in Step 1 of Installing in a Suspended Ceiling section See Figure 9 16 Install ceiling tile and grid by sliding it into the open end of the ceiling tile retainer See Figure 8 A CAUTION Do NOT allow parts of ceiling tile or grid to protrude from the ceiling panel Ensure that all parts assemble easily when installing ceiling tile into ceiling panel Any protruding parts may cause damage to the lift and or ceiling 17 Re install ceiling tile retainer to ceiling panel and secure with four screws removed in Step 11 See Figure 8 18 Use the provided push button B to operate the SL236SP up and down ensuring that all clearances are adequate after the ceiling has been finished Installing in a Wood Framework SL236FD Only 1 Use 1 4 x 1 minimum Grade 2 lag screws not provided to secure SL236FD to the joists or wood framework using the mounting tabs located on the sides of the SL236FD housing See Figure 10 NOTE There are three mounting tabs on each side and two mounting tabs on the front of the SL236FD There are three mounting holes in the back of the SL236FD The SL236FD must be installed using the back mounting holes AND the front two mounting tabs on both sides OR by using the back mounting holes AND the front mounting tabs IMPORTANT Wood framework must be constructed of nothing larger than 2x6 wood studs across the rear of the SL236FD
13. ctions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS A WAR N l NG alerts you to the possibility of serious injury or death if you do not follow the instructions A CAUTI ON alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions A WARN NG FAILURE TO READ AND FOLLOW THE FOLLOWING INSTRUCTIONS CAN RESULT IN SERIOUS PERSONAL INJURY DAMAGE TO EQUIPMENT OR VOIDING OF FACTORY WARRANTY It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided IMPORTANT Model SL236 is suitable for use in
14. e E dM NN EXTEND LIMIT RELAY full extension EXTEND LIMIT RELAY a set of internal dry contacts when unit reaches RETRACT LIMIT RELAY full retraction 19 RETRACT LIMIT RELAY Fo A ojew Grou 14 Installation Instructions SL236 en g AeJc mme Y et pay 10 umoJg H to L i Gu O o MUNI O enum 20 pox OQ o D A4 o ca y SNYM 94D 2 E SS 9 5 2 s S e r 52 3c H E ES HE 55 O mmm T H E O i e ke eld O OO S OO m ra N ei Tt ei m x 9 o A o E m 91IUM E a d nd x U y Y O a t ei 5 e en g Ae T o S E a U ke c Q MOJ 9A LO S e 2 pelg p we o ps peu ed gt euM perg el A NN enig P y Figure 19 15 SL236 Installation Instructions O CH E F USA International Our Mounts Your Vision m Europe Chief Manufacturing a products division of Milestone AV Technologies Asia Pacific 8820 002032 Rev00 2011 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 05 11 mu mu TU 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 T a ei d b o OECONSUNER
15. gure 2 for location of external wiring terminal See Figure 4 for location of internal wiring terminal Installation Instructions SL236 Internal wiring terminal Some parts not shown for clarity Figure 4 Power Requirements and Wiring The SL236 requires 120VAC 60 Hz and 12 amps power to operate IMPORTANT This product must be grounded If it should malfunction or break down grounding provides a path of least resistance for electric current to reduce the risk of electric shock Grounding Instructions This product is equipped with a test cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances WARNING RISK OF ELECTROCUTION All electrical wiring required for installation should be installed by a qualified electrician WARNING PINCH HAZARD FINGERS OR HANDS BETWEEN MOVING PARTS CAN LEAD TO SEVERE PERSONAL INJURY Keep fingers and hands away from mount when operating 8 Pressthe push button B to test the SL236 while it is still in the pre test position Press when the lift is at its top position and it will move down e Press when the lift is at its bottom position and it will move up Press while the lift is moving and it will stop e Leave SL236 in the closed position INSTALLING IN CEILING WARNING IMPROPER INSTA
16. ng See Figure 6 6 Secure the threaded rods to the SL236SP with Grade 2 or better 3 8 in jam nuts not provided and washers one of each on inside and one of each on outside not provided Top view of SL236 Insert rods into 3 slots Figure 6 7 Install the SMA620 optional accessory to the SL236SP if applicable following instructions included with the kit 8 Insert the ceiling grid edge surrounding the SL236SP into the side channel of the SL236SP See Figure 7 NOTE The side channel of the lift will support the weight of the grid and ceiling tiles Side Channel E CAUTION The lift MUST be installed square and parallel Do NOT stress or bend the lift during installation 9 Use the provided push button B to operate the SL236SP up and down ensuring that all clearances are adequate 10 Replace surrounding ceiling tile 11 Remove four screws and the ceiling tile retainer from the ceiling panel See Figure 8 Ceiling Panel Ceiling Tile Retainer Figure 8 12 Cut ceiling tile to fit inside ceiling tile retainer including grid pieces if necessary Installation Instructions SL236 Figure 9 13 Line up clips on four corners of ceiling panel with holes in SL236SP 14 Re install four clips on ceiling panel into rectangular holes on SL236SP See Figure 9 15 Reatta
17. omm Jumper1 amp 5 12 retract 11 extend 2 24V AC Comm Jumper 1 amp 6 3 retract 4 extend Service 9 service 11 service Open N A N A Close Sequence Show Mode Stop N A N A N A N A N A N A Left N A N A Right N A N A Relay Contacts relay closes when unit reaches end of travel Common Error Reversing contact between error input and common indicates an error and unit reverses direction Extend Error Retract Error Common Extend Relay a 13 ground 14 extend error 15 retract error 13 ground 16 extend relay in 9 ground 8 extend error 7 retract error 9 ground 14 extend relay in Extend Relay b 17 extend relay out 12 relay out common Retract Relay a Retract Relay b 18 retract relay in 19 retract relay out 13 retract relay in 12 relay out common EXTERNAL WIRING Figure 18 ayono Jo payoeye BuipunoJB 10 xoq 1 aq pinoys siebuy NOTE The numbers listed in the SL236 Internal and SL236 External columns refer to the corresponding numbers located where indicated in the wiring pictures See Figure 18 13 SL236 Installation Instructions Table 2 INTERNAL TERMINAL DESCRIPTIONS wem pcm keen Jemen OOOO O O O NUMBER DESCRIPTION WIRING OPTIONS AA eme enc a A 24 VOLT AC 24 volt AC output Remote Controllers ay COMMON 24 VOLT AC COMMON
18. ons A CAUTION Changes or modifications to this unit not expressly approved by the manufacturer can void the units FCC compliance rating and make the unit illegal to operate A WAR N l NG Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component A WARN l NG Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the weight of all components attached to the SL236 does not exceed 35 Ibs 15 9 kg A WARN l NG RISK OF INJURY Do not place video equipment such as televisions or computer monitors on the ceiling panel of the SL236 The total weight of any objects on the ceiling panel must not exceed 5 Ibs 2 3 kg NOTE This system has no user serviceable parts SAVE THESE INSTRUCTIONS Installation Instructions SL236 TOOLS REQUIRED FOR INSTALLATION PARTS A 1 Ceiling Lift SL236FD Shown B 1 Push Button Assembly D 1 C 5 External Terminal Cable Tie Cover Plate o E 1 X 9 l Jumper Wire F 5 A Cable Tie un e meant 6 32 x 3 16 rane SZ Rubber Gromme
19. t SL236 Installation Instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Loosen Fastener Aflojar elemento de fijaci n Phillips Screwdriver Marcar con l piz Stiftmarkierung Marcar com l pis Segno a matita gt Potloodmerkteken Marquage au crayon Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations TABLE OF CONTENTS DiSCIAIMEL 200 c0cccecccecceecececceccececeecceceeeeees Installation Heouremente Power Requirements Pre test Lift Before Installanon Power Requirements And Wiring Grounding Instructions Installing In Celmg Installing In A Suspended Ceiling SL236SP 7 Adjust Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Installing In A Wood Framework SL236FD 9 Installing Projector On SL2396 9 Le E E 10 Routing CGables EE 11 Connecting Control Wiring 12 Connecting To Power Supply 12 Wiring ODUOfIS o aoctor utd 12 Table 1 Wiring Table 13 Table 2
Download Pdf Manuals
Related Search