Chief WPAU flat panel wall mount
Contents
1. 158 750 82550 625 32 139 715 5 50 L 28 575 113 OD Installation Instructions WPA Series TOOLS REQUIRED FOR INSTALLATION 3 32 Security Included with SLB bracket hardware os LIT Or other appropriate hardware for attaching product to wall Dpt L SLB bracket not included with WPAO00 G 1 5 32 security WPA000 only B 1 Wall Bracket C 4 Thumb nut E 5 Hardware Cover RV F 4 VVPA000 2 other models WPA Series Installation Instructions ASSEMBLY AND INSTALLATION Attaching Wall Mount to Wall NOTE If attaching optional RPA or RPM interface bracket wall mount adjustment bracket A must be attached to RPA or RPM bracket before being attached to the wall bracket B Proceed to Attaching to RPA or RPM Interface Bracket section for details 1 Attach wall mount adjustment bracket A to the wall bracket B using four thumb nuts C See Figure 1 Figure 2 Attaching SLB Interface Bracket 1 Attach SLB interface bracket D as example to the projector following instructions included with the SLB interface bracket 2 Attach projector with SLB interface bracket to the wall mount adjustment bracket A 3 Tighten thumb nuts See Figure 3 Figure 1 WARNING FAILURE TO PROVIDE ADEQUATE STRUCTURAL STRENGTH FOR THIS COMPONENT CAN RESULT IN SERIOUS PERS2. INSTALLATION INSTRUCTIONS Adjustable Projector Wall Mount CHIEF WPA Series Our Mounts Your Visi WPA Series Installation Instructions DISCLAIMER Milestone AV Technologies Inc and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty I
3. ONAL INJURY OR DAMAGE TO EQUIPMENT It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component 2 Determine location for wall bracket B and locate wall stud to which bracket will be attached 3 Attach wall bracket B to stud through upper hole in wall bracket using 5 16 x 2 long lag bolts and 5 16 flat washers not included through hardware covers E See Figure 2 4 Place second fastener through lower slot in wall bracket B See Figure 2 5 Adjust wall bracket B side to side until it is level and tighten fasteners 6 Close hardware covers E Figure 3 Installation Instructions WPA Series Adjustments 1 Loosen the four thumb nuts on the wall bracket 2 Move projector to get maximum or minimum extension See Figure 4 a Opposite Corners iV H Security screws in Top opposite corners View Maximum eo Extension Figure 5 WPA211 Shown Figure 4 Attaching All Points Security PIS Figure 6 For additional security the All Points Security kit may be installed Attaching to RPA or RPM Bracket Optional 1 Replace four screws fro
4. m the interface bracket preferably NOTE WPA Series mounts may be attached to the RPA or from opposite corners with four security screws F and i additional screws from security kit if applicable See RPM interface bracket in order to allow for more roll Figure 5 pitch and yaw adjustment NOTE Hardware required for RPA or RPM installation is NOT included with WPA Series mounts and must be purchased separately For RPA Attachment 1 Insert four 1 4 20 x 5 8 hex head cap screws into four outermost holes of wall mount adjustment bracket A See Figure 7 2 Attach RPA interface bracket by guiding four 1 4 20 x 5 8 hex head cap screws through four long holes in RPA four 1 4 20 flat washers and into four 1 4 20 Nylock nuts See 5 Installation Instructions VVPA Series Figure 7 3 Tighten Nylock nuts until connection is secure See Figure Figure 7 For RPM Attachment 1 Insert four 1 4 20 x 2 hex head cap screws into four inner holes of wall mount adjustment bracket A See Figure 8 Attach RPM interface bracket by guiding four 1 4 20 x 2 hex head cap screws through four elevated holes in RPM four 1 4 20 flat washers and into four 1 4 20 Nylock nuts See Figure 8 Tighten Nylock nuts until connection is secure See Figure 1 4 20 x 2 x 4 A Figure 8 NOTE Wall mount must be installed to wall before projector can be attached to RPA or RPM interface bracket Refe
5. r back to Attaching Wall Mount to Wall section for details Refer to RPA RPM installation manual to attach projector to RPA or RPM interface bracket NOTE Refer to RPA RPM installation manual for roll pitch and yaw adjustment details Installation Instructions WPA Series WPA Series Installation Instructions CHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8803 000105 Rev B 2009 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 01 09 USA International A 8401 Eagle Creek Parkway Savage MN 55378 P 800 582 6480 952 894 6280 F 877 894 6918 952 894 6918 Europe A Fellenoord 130 5611 ZB EINDHOVEN The Netherlands P 31 0 40 2668620 F 31 0 40 2668615 A Room 24F Block D Lily YinDu International Building LuoGang BuJi Town Shenzhen CHINA RJ 6 A AN BS TRES EI SR AE DPR Asia Pacific P 486 755 8996 9226 P F 486 755 8996 9217 an 10 4
6. t is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the WPA up to and including the display projector does not exceed 50 lbs 22 68 kg Measurements in millimeters inches i i _ 63 500 2 50 peg 12 700 50 e i I P OY 528 701 ik 19323 20 82 561 975 Ds 22 13 ox 349 250 2X 1375 J q m I ses aa lo il 2 63 I il H Ed _ 69 850 27 ay PE ee ee 584200 o o o 231 775 9 13 LENS OFF SET MEASUREMENTS TOP OF MOUNT TO CENTER OF LENS 0 00 203 200 800 OD 231 775 913 OD 2 25 OD 57 150 T L
Download Pdf Manuals
Related Search