JDSU Lil' Buttie Telephone Test Set
Contents
1. Lil Buttie Telephone Test Set User s Guide www dsu com know LOW TALK BELL BATTERY MONITOR SWITCH MUTE LINE POLARITY BUTTON INDICATOR RECALL FROM FLASH MEMORY STORE TO MEMORY REDIAL INSERT PAUSE IN DIALING SEQUENCE HEADSET JACK Caution Please follow correct safety practices when operating this unit Do not connect this unit to 110 volt or 220 volt AC electric power lines In bell mode any signal applied to the unit with more than 250V peak to peak voltage or resulting in more than 7 mA of rms current through ring or tip for a prolonged period of time could damage the unit Correct operation is entirely the responsibility of the user Should the Lil Buttie intentionally or by accident be connected to electric power all warranties are immediately null and void General Description Lil Buttie is a self contained self powered portable telephone test set for use by installers repair technicians and other authorized personnel for temporary communications and to test the operational service and installation of telephone data lines A compact size and comfortable ergonomic shape makes it small enough to carry in your pocket or to wear on your belt while still retaining the normal earpiece to microphone 1 dimensional spacing for comfortable use while resting on the shoulder Included headset jack and ear mounted headset allows for hands free ope2. either ear by rotating the microphone position 90 degrees NOTE When the headset is plugged in the internal handset is disconnected Belt Clip Attachment To install the Belt Clip Attachment remove the strain relief attahment screw and position the Belt Clip as shown Attach the clip using the provided 3 8 flat head screw Take care not to over torque the screw to cause damage to the body Belt clip Optional Accessories For a complete description of optional Field Kits and accessories visit out web site www jdsu com know 13 Battery Installation Battery not included Should the Batt Low LED indicate low battery the battery should be replaced as shown below 1 Using a 1 Phillips screwdriver unscrew and remove the battery cover on the back of the Lil Buttie Connect a 9V Alkaline battery to the battery snaps Slide the battery into the cavity Close the battery cover and replace the screw Do not overtighten When the battery is low the round indicator light above the battery icon will be on and the battery should be replaced as soon as possible Specifications Electrical Return Loss 600 ohms Greater Than 14dB Line Current Range 15 to 85 mA Apparent Line Resistance 275 ohms at 20mA Rotary Dial Output Pulse Rate 10 pps 10 M B Ratio 60 40 2 Interdigit Interval 820 mSec Leakage During Break gt 120 Kohms DTMF Output into 600 ohms Tone Frequency Err
3. store the number Ten 17 digit numbers can be stored Last P When pressed first the last number dialed will be redialed from the unit s internal memory When pressed after another digit a pause of approximately 3 6 seconds is inserted in the dialing sequence for psx or Centrex switch dialing or other systems that require an intermediate access digit in order to access a line Mem To retrieve a stored number press Mem and the numeric key 0 9 you stored the number to and the number will be automatically dialed Line Polarity Indicators NORM A green Leo indicates correct polarity REV A red Leo indicates reversed line polarity Battery Low BATT LOW When operated in the Monitor or Talk mode the Leo will light up if low battery voltage is detected Operation NOTE Always position the Talk Bell Monitor Switch in the Monitor position before connecting to a subscriber line to avoid possibly compromising any transmission in progress Connecting to a Line Monitor 1 2 Select the Monitor mode Connect the Rep cord set lead to Ring and stack cord set lead to Tip NORM Or REV polarity LED will come on if the line is powered Listen for voices ambient noise or buzzing sounds indicating digital data Note If detected the Low Batt LeD will indicate a low operating voltage in this mode Dialing 1 2 Select the Monitor mode Connect the Rep cord set lead to Ring and stack
4. ade Services e Immediate Return Authorizations Technical Assistance Expert business hour technical support is included with your product Instrument Repair Our service centers provide repair calibration and upgrade services for JDSU equipment JDSU understands the impact of equipment down time on operations and is staffed to ensure a quick turnaround Available services include the following Product Repair All equipment returned for service is tested to the same rigorous standards as newly 18 manufactured equipment This ensures products meet all published specifications including any applicable product updates Calibration JDSU s calibration methods are ISO approved and based on national standards Factory Upgrades Any unit returned for a hardware feature enhancement will also receive applicable product updates and will be thoroughly tested ensuring peak performance of the complete feature set Equipment Return Instructions Please contact your regional Technical Assistance Center to get a Return or Reference Authorization to accompany your equipment For each piece of equipment returned for repair attach a tag that includes the following information Owner s name address and telephone number The serial number if applicable product type and model e Warranty status If you are unsure of the warranty status of your instrument contact Technical Assistance e Adetailed descriptio
5. cord set lead to Tip Confirm that the line is not in use Position the Tone Pulse Switch to either tone or pulse dialing 7 5 Select the Talk mode and confirm that dial tone is present 6 Proceed with dialing line testing etc Mixed Mode Dialing In certain situations it may be necessary to set up a call using both Pulse and Tone dialing In this situation a number can be entered in the Pulse mode then by pressing the T button the unit will switch to Tone mode so that tones can be sent to devices such as answering machines etc that are activated by specific tone codes Last Number Redial The last number dialed can automatically be redialed in either the Tone or Pulse modes To redial the last number switch from Talk to Monitor then back to Talk mode Once you have confirmed a dial tone press the Last P button on the keypad Ringer 1 Select the Bell mode 2 Connect the rep cord set lead to Ring and stack cord set lead to Tip 3 The unit will now ring when ringing voltage is detected on the line 8 4 To answer the call switch the unit to TALK 5 To disable the ringer switch the unit to MONITOR mode Polarity Check The Lil Buttie indicates Polarity continuously in Monitor and Talk modes as long as the line is powered 1 To test select the monitor or TALK mode 2 Connect the slack cord set lead to Ring and rep cord set lead to Tip 3 The red Leo will ligh
6. ke an ordinary telephone Bell This position connects the internal electronic ringer for receipt of incoming ring signals This on hook mode also isolates both the testing and speech circuits from the line Monitor The battery is off in this mode This position connects the test set through a high impedance coupling This on hook connection allows for telephone line monitoring without disturbing conversations network signaling or data transmissions In this mode the unit s speech ring and test circuits are isolated from the line Tone Pulse Switch This two position slide switch is used to select the dialing mode The TONE position selects ptmr signaling The PULSE position selects rotary style pulse dialing Mute This button is located on the opposite side of the Talk Bell Monitor switch Press and hold to shut the unit s transmitter off This feature may also be used to improve communications in noisy locations where it is difficult for the user to hear a person on the other end of the line Flash When pressed causes a 0 6 second interruption of the loop current hook flash Usually used for register recall to put a call on hold to activate a second line or where some special function needs to be activated T When pressed in pulse mode switches from PuLsE to TONE dialing mode Store Press Store enter the number you wish to store press Store and the location on the numeric keypad 0 9 where you wish to
7. ld not be disposed of as unsorted municipal waste and should be collected separately and disposed of according to your national regulations In the European Union all equipment purchased from JDSU after 005 08 13 can be returned for disposal at the end of its useful life JDSU will ensure that all waste equipment returned is reused recycled or disposed of in an environmentally friendly manner and in compliance with all applicable national and international waste legislation It is the responsibility of the equipment owner to return the equipment to JDSU for appropriate disposal If the equipment was imported by a reseller whose name or logo is marked on the equipment then the owner should return the equipment directly to the reseller Instructions for returning waste equipment to JDSU can be found in the Environmental section of JDSU s web site at www jdsu com If you have questions concerning disposal of your equipment contact JDSU s WEEE Program Management team at WEEE EMEA jdsu com Notes www jdsu com know Document Information Doc TU9822 Revision 501 06 08 English
8. n of the 19 problem or service requested e The name and telephone number of the person to contact regarding questions about the repair e The return authorization RA number US customers or reference number European Customers If possible return the equipment using the original shipping container and material If the original container is not available the unit should be carefully packed so that it will not be damaged in transit when needed appropriate packing materials can be obtained by contacting JDSU Technical Assistance JDSU is not liable for any damage that may occur during shipping The customer should clearly mark the JDSU issued RA or reference number on the outside of the package and ship it prepaid and insured to JDSU Warranty Information JDSU guarantees that its products will be free of all defects in material and workmanship This warranty extends for the period of 12 months for test instruments and 3 months for cables from date of manufacture or purchase proof of purchase required All product deemed defective under this warranty will be repaired or replaced at JDSU s discretion No further warranties either implied or expressed will apply nor will responsibility for operation of this device be assumed by JDSU amp WEEE Directive Compliance JDSU has established processes in compliance with the Waste Electrical and Electronic Equipment WEEE Directive 2 002 96 EC This product shou
9. or 1 5 Tone Level High Group 6dBm 2dB Low Group 8dBm 2dB High vs Low Tone Difference 2dB 1dB Memory Dialing Type Last Number Redial Mode Tone and Pulse Retention with battery gt 2yrs without 8 min nominally Capacity 32 Digits Ringer Electronic Dual Tone 15 Physical Length without Lanyard 7 25 in 18 4 cm Width 2 50 in 6 4 cm Height 1 68 in 4 3 cm Weight with Cord Set 8 ozs 227 gms Environmental Temperature operating 10 C to 60 C storage 40 C to 66 C Specifications subject to change 16 Maintenance The test set may be cleaned with a damp cloth If heavy accumulations of dirt are present a small amount of liquid soap may be applied to the cloth to assist in cleaning Do not use solvents scouring powders or other abrasive cleaners as they may scratch the unit and or cause malfunctions Cord sets should be periodically checked for shorts continuity or obvious signs of wear such as fraying or loose damaged test clips 17 Customer Services This section provides a description of customer services available through JDSU including returns policies and procedures and warranty information Customer Service Standard Services Customer Service accompanies the sale of every JDSU product Customer Service services include e Technical Assistance Business Hour Instrument Repair Under Warranty Repair Calibration Services and Upgr
10. ration Headset is compact enough to fit in a shirt pocket and can be worn on either ear Its unobtrusive design makes it easy to use while wearing a hard hat or inclement weather clothing The body is made of high impact resistant Ass to withstand the rough handling and shocks that craft tools are normally subjected to in their everyday use A belt loop provides a convenient and secure location for the attachment of the unit to various locations An optional belt clip attachment is also provided The modular jack cord set with strain relief feature allows for easy field replacement or direct connection to modular wall jack with a standard phone cord set Features Tone and Pulse Dialing e Microphone Mute Feature Last Number Redial 32 Digits e Continuous Line Polarity Indication TALK Or MONITOR e Electronic Ringer e Amplified Line Monitor for volume levels comparable to off hook operation e Modular cord set attachment e Low Battery Indicator e Headset Jack for hands free operation Battery Powered Monitor Mode with auto power off on dead lines or when disconnected Function Switches Buttons and LEDs Talk Bell Monitor Switch This three position slide switch is located on the side of the unit below the receiver It is used to select the mode of operation Talk This position creates an off hook condition In this mode the unit can be used for signaling conversation and testing just li
11. t up if the leads are reversed and the green Leo will light up if the polarity is correct Line Cord Connections The Lil Buttie is designed with a standard 6 position modular jack for quick connection to various cord sets The jack is located at the base of the unit below the microphone To replace the cord set simply remove the strain relief attachment screw and unplug the cord set Insert the new cord set and replace the terminal and screw 10 Models Options amp Accessories Ordering Description number LB100 Lil Buttie telephone test set with piercing pin clips LB110 Lil Buttie telephone test set with angled bed of nails clips Lil Buttie telephone test set LB110 BT with angled bed of nails clips and protective rubber boot Lil Buttie telephone test set with angled bed of nails clips non N America 100ms hook LBTIOUKAUS flash 37 63 make break ratio and protective rubber boot Lil Buttie telephone test set LB115 with angled bed of nails clips and rugged hook style belt clip LB10B RJ11 to alligator 48 cord with strain relief LB25 RJ11 to piercing pin 48 with strain relief LB30B RJ11 to angled bed of nails clips 48 with strain relief Headset The included headset can be utilized when a hands free operation is preferred Plug the headset into the receptacle located at the base of the unit next to the modular plug receptacle The headset can be used for
Download Pdf Manuals
Related Search