Home

Draytek VigorAP 700

1. Here are descriptions of every setup item Band Channel Please select the wireless band you wish to use By selecting different band setting you ll be able to allow or deny the wireless client of a certain band If you select 2 4GHz B 2 4GHz N or 2 4GHz G only wireless clients using the wireless band you select 802 11b 802 11n or 802 11g will be able to connect to this access point If you select 2 4GHz B G then only wireless clients using 802 11b and 802 11g band will be able to connect to this access point If you want to allow 802 11b 802 11g and 802 11n clients to connect to this access point select 2 4GHz B G N Please select a channel number you wish to use The channel number must be same with another VigorAP 700 you wish to connect MAC address 1 4 DrayTek Please input the MAC address of the VigorAP 700 you wish to connect 25 VigorAP 700 User s Guide After you finish with setting please click Apply and the following screen will be displayed Save setting successfully You may press Continue to configure other settings or press Apply to restart the system for changes to take effect When you see this message the settings you made is successfully save You can click Continue to return to previous page and continue on other setting items or click Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds 2 4 5 AP Bridge WDS M
2. Config Mode There are Registrar and Enrollee modes for the WPS connection When Registrar is enabled the wireless clients will follow the access point s wireless settings for WPS connection When Enrollee mode is enabled the access point will follow the wireless settings of wireless client for WPS connection Start PBC Click Start PBC to start Push Button style WPS setup procedure This access point will wait for WPS requests from wireless clients for 2 minutes The WLAN LED on the access point will be steady on for 2 minutes when this access point is waiting for incoming WPS request Start PIN Please input the PIN code of the wireless client you via client wish to connect and click Start PIN button The WLAN LED on the access point will be steady on when this access point is waiting for incoming WPS request Note When you re using PBC type WPS setup you must press PBC button hardware or software of wireless client within 2 minutes If you didn t press PBC button of wireless client within this time period please press PBC button hardware or software of this access point again VigorAP 700 User s Guide 32 Dray Tek 2 6 Advanced Wireless Settings This VigorAP 700 has many advanced wireless features Please note that all settings listed here are for experienced users only If you re not sure about the meaning and function of these settings please don t modify them otherwise the wireless performance will be
3. aY af E 802 1 ln Access Point Your reliable networking solutions partner User s Guide V1 1 VigorAP 700 User s Guide ii Dray Tek VigorAP 700 Wireless Access Point User s Guide Version 1 1 Date 13 01 2011 Dray Tek iii VigorAP 700 User s Guide COPYRIGHT Copyright 92011 by this company All rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of this company This company makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties merchantability or fitness for any particular purpose Any software described in this manual is sold or licensed as is Should the programs prove defective following their purchase the buyer and not this company its distributor or its dealer assumes the entire cost of all necessary servicing repair and any incidental or consequential damages resulting from any defect in the software Further this company reserves the right to revise this publication and to make changes from time to time in the contents thereof without obligation to notify any person of such revision or changes Federal Communication Commission Interference Statement FC
4. VigorAP 700 User s Guide 48 Dray Tek 2 10 3 DHCP Server This VigorAP 700 1s capable to act as a DHCP server for your network It is disabled by default If you want to activate this function please click System Utility on the left and the following screen will be displayed e DHCP Server BEEN merch eee 0 0 0 0 Blue IUR Eul a 0 0 0 0 S IER 192 168 1 100 zilei 192 168 1 200 Domain Name REUTER Forever v Here are descriptions of every setup item Default Gateway IP Please input the IP address of default gateway of your network here Domain Name Server IP Start IP Please input the IP address of domain name server DNS here Please input the start IP address of the IP range End IP Please input the end IP address of the IP range Domain Name If you wish you can also optionally input the domain name for your network This is optional Lease Time Please choose a lease time the duration that every computer can keep a specific IP address of every IP address assigned by this access point from dropdown menu After you finish please click Apply and the following screen will be displayed Save setting successfully You may press Continue to configure other settings or press Apply to restart the system for changes to take effect Dray Tek 49 VigorAP 700 User s Guide When you see this message the settings you made is successful
5. in the field of IP address on this section for your computer If the operating system of your computer is Windows 95 98 Me please go to section 2 2 1 Windows 2000 please go to section 2 2 2 Windows XP please go to section 2 2 3 Windows Vista please go to section 2 2 4 2 2 1 Windows 95 98 Me IP address setup 1 Click Start button it should be located at lower left corner of your computer then click control panel Double click Network icon and the Network window will appear Select TCP IP then click Properties Network 21x Configuration Identification Access Control The following network components are installed 2 Client for Microsoft Networks Client for NetWare Networks SMC EtherPower Adapter SMC8432 ef E Lac Pk compatible Protocol a e ef Pon E SEE e Sal menn Remove Properties D Se di Primary Network Logon Sea Client for Microsoft Networks File and Print Sharing m Description TCPAIP is the protocol you use to connect to the Internet and wide area networks VigorAP 700 User s Guide 8 Dray Tek 2 Select Specify an IP address then input the following settings in respective field and click OK when finish IP address 192 168 1 9 Subnet Mask 255 255 255 0 TCP IP Properties m Dray Tek 9 VigorAP 700 User s Guide 2 2 2 Windows 2000 IP address setup l Internet Protocol TCP IP then click Properties Gen
6. 802 1 1b g n wireless devices e High speed wireless network six times faster than conventional 802 11g wireless network up to 300Mbps e Allow wireless devices to connect to existing wired network and share network resources e Supports DHCP server function e Supports 64 128 bit WEP WPA and WPA2 wireless data encryption e Supports MAC address filtering Only allow specific wireless device of your choice to connect to this access point e Supports RADIUS server only allow users listed in your authorization server to use wireless network e Supports WPS Wi Fi Protected Setup simplifies wireless client setup procedures Even inexperienced user can setup wireless network without network technician s help e Easy to use web based GUI Graphical User Interface for network configuration and management purposes Dray Tek 1 VigorAP 700 User s Guide 1 2 Safety Information In order to keep the safety of users and your properties please follow the following safety instructions This access point is designed for indoor use only DO NOT place this access point outdoor DO NOT put this access point at or near hot or humid places like kitchen or bathroom Also do not left this access point in the car in summer DO NOT pull any connected cable with force disconnect it from the access point first If you want to place this access point at high places or hang on the wall please make sure the access point is fi
7. 700 User s Guide This page is left blank VigorAP 700 User s Guide 54 Dray Te k Chapter III Troubleshooting If you found the access point is working improperly or stops responding to you don t panic Before you contact your dealer of purchaser for help please read this troubleshooting first Some problems can be solved by yourself within a short time Scenario Solution Access point is not responding to me when I want to access it by web browser Ifall LEDs on this access point are out please check the Are you using MAC or IP address filter Try to connect Ifall above solutions don t work contact the dealer of Please check the connection of power cord and network cable of this access point All cords and cables should be correctly and firmly inserted to the access point status of A C power adapter and make sure it s correctly powered You must use the same IP address section which access point uses the access point by another computer and see if it works If not please perform a hard reset pressing Reset WPS button Set your computer to obtain an IP address automatically DHCP and see if your computer can get an IP address If you have done a firmware upgrade and this happens still contact your dealer of purchase for help purchase for help Can t get connected to VigorAP 700 Dray Tek Try to move closer to VigorAP 700 Ifall LEDs on this access poin
8. A subnet mask which may be a part of the TCP IP information provided by your ISP is a set of four numbers e g 255 255 255 0 configured like an IP address It is used to create IP address numbers used only within a particular network as opposed to valid IP address numbers recognized by the Internet which must be assigned by InterNIC TCP IP UDP Transmission Control Protocol Internet Protocol TCP IP and Unreliable Datagram Protocol UDP TCP IP is the standard protocol for data transmission over the Internet Both TCP and UDP are transport layer protocol TCP performs proper error detection and error recovery and thus is reliable UDP on the other hand is not reliable They both run on top of the IP Internet Protocol a network layer protocol WAN Wide Area Network A network that connects computers located in geographically separate areas e g different buildings cities countries The Internet is a wide area network Web based management Graphical User Interface GUI Many devices support a graphical user interface that is based on the web browser This means the user can use the familiar Netscape or Microsoft Internet Explorer to Control configure or monitor the device being managed Dray Tek 59 VigorAP 700 User s Guide
9. and static electricity when working with electrical equipment All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment Dray Te k v VigorAP 700 User s Guide EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria Belgium Denmark Finland France Germany Greece Ireland Italy Luxembourg the Netherlands Portugal Spain Sweden and the United Kingdom The ETSI version of this device is also authorized for use in EFTA member states Iceland Liechtenstein Norway and Switzerland EU Countries Not intended for use None Please visit http www draytek com user AboutRegulatory php Zo This product is designed for 2 4GHz WLAN network throughout the EC region and Switzerland with restrictions in France VigorAP 700 User s Guide vi Dray Te k Table of Content Chapter l Product Information nnnsnnnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnana 1 T t MUO NSE kt see ar alo ae a i oa ai Za pa id ci isa ta N a aaa ie 1 1 2 Safety ere 2 ees 3 1 4 Familiar with your new VigorAP 700 mmmnnnoee eee neeeennnee eee anna nananaanaeaean mana 4 Chapter II System and Network Setup mcnnee nenea eee 7 2 1 Installing VigorAP 700 to your Network nenea EEN 7 2 2 Connecting to VigorAP 700 by Using Web Browser nenea neam ea 8 2 2 1 Windows 95 98 Me IP address sei
10. appear which contains the information about all AP with repeater mode connected to this access point You can click Refresh button in popup window to keep information up to date Root AP SSID In Universal Repeater mode this device can act as a station to connect to a Root AP You should assign the SSID of the Root AP here or click Select Site Survey button to choose a Root AP Site Survey Dray Tek Click Wireless Site Survey button then a Wireless Site Survey Table will pop up It will list all available access points near by You can select one access point in the table and the access point will join wireless LAN through this access point Please go to Section 29 VigorAP 700 User s Guide 2 4 2 1 for more information about the Wireless Site Survey Table After you finish with setting please click Apply and the following screen will be displayed Save setting successfully fou may press Continue to configure other settings or press Apply to restart the system for changes to take effect When you see this message the settings you made is successfully save You can click Continue to return to previous page and continue on other setting items or click Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds 2 5 WPS Setting Wi Fi Protected Setup WPS is the simplest way to build connection between wireless network clients and this access point You don t have to select encryption m
11. connect to this access point If you want to allow 802 11b 802 11g and 802 11n clients to connect to this access point select 2 4GHz B G N MAIN SSID Please input the SSID the name used to identify this VigorAP 700 here You can input up to 32 alphanumerical characters PLEASE NOTE THAT SSID IS CASE SENSITIVE Multiple SSID The access point supports multiple SSID function up to four SSIDs can be set If you want to configure additional SSIDs please click this button For detailed descriptions of the function please refer to Section 2 4 1 1 Channel Please select a channel number you wish to use The channel number must be same with another VigorAP 700 you wish to connect Associated Clients Click Show Active Clients button and a new popup window will appear which contains the information about all wireless clients connected to this access point You can click Refresh button in popup window to keep information up to date Associated WDS AP Click Show WDS AP button and a new popup window will appear which contains the information about all WDS AP connected to this access point You can click Refresh button in popup window to keep information up to date MAC address 1 4 Please input the MAC address of the VigorAP 700 you wish to connect After you finish with setting please click Apply and the following screen will be displayed Dray Tek 27 VigorAP 700 User s Guide Save
12. reduced You can click Advanced Setting on the left to enter advanced settings menu The following screen will be displayed Advanced Settings Broadband router REN MED A CS 2346 256 2346 A ESI 2347 0 2347 Beacon Interval 100 20 1024 ms DTIM Period ME 1 10 W IEE Auto Y SEENEN Auto v SEIEKdEIIN Auto 20 40 MHZ 20 MHZ CELB IHR Short Preamble Long Preamble Isiya Enable Disable MU Enable Disable MACI Auto Always O None TX Power 100 ze Here are descriptions of every setup item Fragment Threshold Set the Fragment threshold of wireless radio Do not modify default value if you don t know what it is default value is 2346 RTS Threshold Set the RTS threshold of wireless radio Do not modify default value if you don t know what it is default value is 2347 Beacon Interval Set the beacon interval of wireless radio Do not modify default value if you don t know what it is default value is 100 DTIM Period Set the DTIM period of wireless radio Do not modify default value if you don t know what it is default value is 3 Dray Tek 33 VigorAP 700 User s Guide Data Rate Set the wireless data transfer rate to a certain value Since most of wireless devices will negotiate with each other and pick a proper data transfer rate automatically it s not necessary to change this value unless you know wh
13. will greatly improve security 3 Use WPA when possible it s much safer than WEP 4 Change encryption password when you ve used it for too long time VigorAP 700 User s Guide 36 Dray Tek 2 7 1 Disable Security Select the SSID you wish to configure When you select Disable wireless encryption for the network is disabled Security This page allows you to setup the wireless security To prevent any unauthorized access to your wireless network please turn on WEP or WPA encryption e Select SSID ta BR ll DrayTek v e Security Settings Enable 802 1x Authentication After you finish with setting please click Apply and the following screen will be displayed Save setting successfully You may press Continue to configure other settings or press Apply to restart the system for changes to take effect When you see this message the settings you made is successfully save You can click Continue to return to previous page and continue on other setting items or click Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds 2 7 2 WEP WEP Wired Equivalent Privacy is a common encryption mode It is safe enough for home and personal use However if you need higher level of security please consider using WPA encryption see next section Some wireless clients do not support WPA but support WEP Therefore WEP is still a good choice for you if you have such kind of client in
14. your network environment When you select WEP as encryption type the following screen will be displayed Dray Tek 37 VigorAP 700 User s Guide e Select SSID SSID choice e Security Settings Encryption Key Length Key Format Default Tx Encryption Key 1 Encryption Key 2 Encryption Key 3 Encryption Key 4 Key DrayTek 64 bit e Hex 10 characters vi Key 1 v dekre Ke Ke Ke e KR iii RRR RRR C Enable 802 1x Authentication Here are descriptions of every setup item Key Length There are two types of WEP key length 64 bit and 128 bit Using 128 bit is safer than 64 bit but it will reduce some data transfer performance Key Format Default Tx Key There are two types of key format ASCII and Hex When you select a key format the number of characters of key will be displayed For example if you select 64 bit as key length and Hex as key format you ll see the message at the right of Key Format is Hex 10 characters which means the length of WEP key is 10 characters You can set up to four sets of WEP key and you can decide which key is being used as default here If you don t know which one you should use select Key 1 Encryption Key 1 to 4 Input WEP key characters here the number of characters must be the same as the number displayed at Key Format field You can use
15. Auto TX Power You can set the output power of wireless radio Unless you re using this VigorAP 700 in a really big space you may not have to set output power to 100 This will enhance security malicious unknown users in distance will not be able to reach your VigorAP 700 After you finish with setting please click Apply and the following screen will be displayed VigorAP 700 User s Guide 34 Dray Tek Save setting successfully You may press Continue to confiqure other settings or press Apply to restart the system for changes to take effect When you see this message the settings you made is successfully save You can click Continue to return to previous page and continue on other setting items or click Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds 2 7 Wireless Security This VigorAP 700 provides many types of wireless security wireless data encryption When you use data encryption data transferred by radio signals in the air will become unreadable for those people who don t know correct encryption key encryption password There are two ways to set wireless security e Click Security on the left of web management interface Security This page allows you to setup the wireless security To prevent any unauthorized access to your wireless network please turn on WEP or WPA encryption e Select SSID EIS DrayTek e Security Settings Enable 802 1x Authen
16. C Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio technician for help VigorAP 700 User s Guide iv Dray Te k FCC Caution This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm spacing must be provided between computer mounted antenna and person s body excluding extremities of hands wrist and feet during wireless modes of operation This device complies with Part 15 of the FCC Rules Operation is s
17. P 700 main body 1 pcs Antenna 2 pcs Quick Start Guide 1 pcs A C power adapter 1 pcs CD documentation Dray Tek 3 VigorAP 700 User s Guide 1 4 Familiar with your new VigorAP 700 Front Panel SET AEE Zz EE N DrayTek Agar Aa 700 Gi A ina LED Status Description On The device is powered on PWR Off The device is powered off On Wireless WPS mode is enabled WLAN Blinking Data is transmitting sending receiving On LAN port is connected LAN Off LAN port is not connected Blinking Data is transmitting sending receiving VigorAP 700 User s Guide 4 Dray Te k Back Panel Reset WPS Interface Description Antennas Two reserve SMA antenna connectors for screwing 3dBi detachable antennas enclosed with the product Reset Restore the default settings WPS Usage Turn on the VigorAP 700 Press the button and keep for more than 10 seconds Then the AP will restart with the factory default configuration Press the button and keep it less than 5 seconds the WPS connection will be enabled LAN Connecter for local networked devices O Connecter for a power adapter Dray Tek 5 VigorAP 700 User s Guide This page is left blank VigorAP 700 User s Guide 6 Dray Te k Chapter II System and Network Setup 2 1 Installing VigorAP 700 to your Network Plea
18. Registrar ze Configure via Push Button Start PBC Configure via Client PinCode Start PIN Here are descriptions of every setup item Enable WPS Check this box to enable or disable WPS function Wi Fi Protected Setup All information related to WPS will be displayed here They re Information helpful when you re setting up connections by WPS WPS Status Displays WPS status If data encryption settings of this access point has never been set unConfigured message will be displayed her see Section 2 7 for detailed information if data encryption settings has been set before Configured message will be displayed here Self PinCode This is the WPS PIN code of this access point This code is useful when you need to build wireless connection by WPS with other WPS enabled wireless devices SSID Displays the SSID SSID of this access point Authentication Mode The wireless security authentication mode of this access point will be displayed here If you don t enable security function of the access point before WPS is activated the access point will auto set the security to WPA AES and generate a set of passphrase key for WPS connection Passphrase Key Displays the WPA passphrase here all characters will be replaced by asterisk for security reason If encryption is not Dray Tek 31 VigorAP 700 User s Guide set on this access point nothing will be displayed here Device Configuration
19. address 1 Please input the MAC address of the VigorAP 700 you wish to connect After you finish with setting please click Apply and the following screen will be displayed Save setting successfully You may press Continue to configure other settings or press Apply to restart the system for changes to take effect When you see this message the settings you made is successfully save You can click Continue to return to previous page and continue on other setting items or click Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds VigorAP 700 User s Guide 24 Dray Te k 2 4 4 AP Bridge Point to Multi Point Mode In this mode this VigorAP 700 will connect to up to four VigorAP 700s which uses the same mode and all wired Ethernet clients of every VigorAP 700s will be connected together You can use this mode to connect a network to other networks which is physically isolated Please note that when you set your access point to this mode it will not accept regular wireless clients anymore When you select AP Bridge Point to Multi Point the following screen will be displayed Basic Settings This page allows you to define Mode Band and settings corresponding to the mode selected for the wireless connection AP Bridae Point to Multi Point Y 24 Ghe Ee 000000000000 000000000000 000000000000 ooooooo00000
20. any alphanumerical characters 0 9 a z and A Z if you select ASCII key format and if you select Hex as key format you can use characters 0 9 a f and A F You must enter at least one encryption key here If you entered multiple WEP keys they should not be the same with each other Enable 802 1x VigorAP 700 User s Guide Check this box to enable 802 1x user authentication Please refer to 38 Dray Tek Authentication Section 2 7 5 for detailed instructions After you finish with setting please click Apply and the following screen will be displayed Save setting successfully You may press Continue to configure other settings or press Apply to restart the system for changes to take effect When you see this message the settings you made is successfully save You can click Continue to return to previous page and continue on other setting items or click Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds 2 7 3 WPA Pre shared Key WPA Pre shared key is the safest encryption method currently and it is recommended to be used to ensure the safety of your data When you select WPA pre shared key as encryption type the following screen will be displayed e Security Settings Encryption WPA pre shared key ieee WPA TKIP OWPA2 AES OWPA WPAZ2 Mixed Leia seci alai Passphrase Pre shared Key Here are descriptions of ever
21. at will happen after modification N Data Rate Set the data rate of 802 1 In clients available options are MCS 0 to MCS 15 It s safe to set this option to Auto and it s not necessary to change this value unless you know what will happen after modification Channel Width Select wireless channel width bandwidth taken by wireless signals of this access point It s suggested to select Auto 20 40MHz Do not change to 20 MHz unless you know what it is Preamble Type Set the type of preamble of wireless radio Do not modify default value if you don t know what it is Default setting is Short Preamble Broadcast SSID Decide if the VigorAP 700 will broadcast its own SSID or not You can hide the SSID of your VigorAP 700 set the option to Disable then only people who know the SSID of your VigorAP 700 can get connected WMM WMM Wi Fi Multimedia technology which can improve the performance of certain network applications like audio video streaming network telephony VoIP and others When you enable WMM function the access point will define the priority of different kinds of data to give higher priority to applications which require instant responding Therefore you can improve the performance of such network applications CTS Protect Enabling this setting will reduce the chance of radio signal collisions between 802 11b and 802 11g VigorAP 700s It s recommended to set this option to
22. ble to allow or deny the wireless VigorAP 700 User s Guide 28 Dray Tek client of a certain band If you select 2 4GHz B 2 4GHz N or 2 4GHz G only wireless clients using the wireless band you select 802 11b 802 1 In or 802 11g will be able to connect to this access point If you select 2 4GHz B G then only wireless clients using 802 11b and 802 11g band will be able to connect to this access point If you want to allow 802 11b 802 11g and 802 11n clients to connect to this access point select 2 4GHz B G N MAIN SSID Please input the SSID the name used to identify this VigorAP 700 here You can input up to 32 alphanumerical characters PLEASE NOTE THAT SSID IS CASE SENSITIVE Multiple SSID The access point supports multiple SSID function up to four SSIDs can be set If you want to configure additional SSIDs please click this button For detailed descriptions of the function please refer to Section 2 4 1 1 Channel Please select a channel number you wish to use The channel number must be same with another VigorAP 700 you wish to connect Associated Clients Click Show Active Clients button and a new popup window will appear which contains the information about all wireless clients connected to this access point You can click Refresh button in popup window to keep information up to date Associated Repeater Click Show Repeater AP button and a new popup window will AP
23. connected networks 2 Select Use the following IP address then input the following settings in respective field and click OK when finish IP address 192 168 1 9 Subnet Mask 255 255 255 0 Internet Protocol Version 4 TCP IPv4 Properties General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address autopativaly BEB EERE eee Use the following IP addr ss IP a 192 168 1 9 et mask 255 255 255 0 Default gateway f ain DNS serve one automatically LEE Use the following DNS server addresses Preferred DNS server Alternate DNS server VigorAP 700 User s Guide 12 Dray Tek 2 2 5 Connecting to Web Management Interface All functions and settings of this access point must be configured via web management interface Please start your web browser and input 192 168 1 2 in address bar then press Enter key The following screen should be shown Connect to 192 168 1 2 Default admin no password User name ft Password C Remember my password Please input user name and password in the field respectively The default user name is admin and no password needed Next press OK and you can see the web management interface of this access point _ Vigor ARG Dray Tek iei Pi ay Nees Kini e Home Statu
24. d button Or you can click Delete All button to delete all users in radius server database Authentication Client If you want to use such Access Point as the Radius server for other AP or network devices you can add allowed radius client IP address here Please input client IP secret key confirm secret key in corresponding field and click Add button to add the IP address to radius server database You can click Cancel to clear the text you typed in above three fields All current IP addresses will be listed here If you want to delete one or more addresses check the box of that address and click Delete Selected button Or you can click Delete All button to delete all addresses in radius server database After you finish with setting please click Apply and the following screen will be displayed Save setting successfully fou may press Continue to configure other settings or press Apply to restart the system for changes to take effect When you see this message the settings you made is successfully save You can click Continue to return to previous page and continue on other setting items or click Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds VigorAP 700 User s Guide 44 Dray Te k 2 9 MAC Filtering Another security measure you can use to keep hackers and intruders away is MAC filtering You can pre define a so called white list which contains MAC addresses of th
25. d to the wired network Station Infrastructure Enable the Ethernet device such as TV and Game player connected to the access point to a wireless client AP Bridge Point to Point Establish wireless connection with another VigorAP 700 AP Bridge Point to Multi Point using the same mode and link the wired network which these two VigorAP 700s connected together Only one access point can be connected in this mode Establish wireless connection with other VigorAP 700s using the same mode and link the wired network which these VigorAP 700s connected together Up to 4 access points can be connected in this mode AP Bridge WDS VigorAP 700 User s Guide This mode is similar to AP Bridge to Multi Point but access point is not work in bridge dedicated mode and will be able 16 Dray Tek to accept wireless clients while the access point is working as a wireless bridge Universal Repeater This product can act as a wireless range extender that will help you to extend the networking wirelessly The access point can act as Station and AP at the same time It can use Station function to connect to a Root AP and use AP function to service all wireless clients within its coverage Please select one wireless operating mode For detailed descriptions of every operating mode please refer to Section 2 4 1 to 2 4 6 listed below 2 4 1 AP Mode This is the most common mode When in AP mode the access point acts as a bridge be
26. dentification name of this access point it can not be modified by user Displays the number of connected wireless client IP Address Displays the IP address of this VigorAP 700 Subnet Mask Displays the net mask of IP address Default Gateway Displays the IP address of default gateway MAC address Displays the MAC address of LAN interface Dray Tek 15 VigorAP 700 User s Guide 2 4 Select an Operating Mode for Wireless Access Point This access point can be operated in different modes you can click Basic Setting on the left of web management interface to select an operating mode you want to meet for different needs MAL jo re 7 de Dray Tek 802 1 n Access PONI Home Basic Settings WPS Setting Advanced Settings Security e RADIUS Server MAC Filtering e System Utility Configuration Tool e Firmware Upgrade e Restart Status and Information This page shows System Status Wireless Configuration and LAN Configuration information System Uptime Oday Oh 2m 23s Hardware Version Rev A Firmware Version 1 04 Mode AP SSID DrayTek Channel Number 11 Security Disable BSSID 00 50 7f 37 97 20 Associated Clients D LAN Configuration IP Address 192 168 1 2 You can click Mode dropdown menu to select operating mode and there are 6 operating modes available AP Access point mode allows wireless clients to connect to access point and exchange data with the devices connecte
27. e wireless clients you trust All other wireless clients with the MAC addresses which not in your list will be denied by this VigorAP 700 To setup MAC filtering please click MAC Filtering on the left of web management interface and the following screen will be displayed MAC Address Filtering For security reason the Access Point features MAC Address Filtering that only allows authorized MAC Addresses associating to the Access Point Select SSID Geo w e MAC Address Filtering Table Up to 20 entries of MAC addresses are allowed KSC RER C Enable Wireless Access Control Address Comment Note If you have enabled Multiple SSID function please select the SSID network you wish to configure in advance This page contains MAC filtering information All allowed MAC addresses will be listed in this page For adding new MAC address please type new MAC addresses in the MAC Address field and click Add Here are descriptions of every setup item Select SSID Select the SSID you wish to configure for MAC filtering Select Check this box to select one or more MAC address es to delete Delete Selected Click this button to delete all selected MAC address es Delete All Delete all MAC address entries Dray Tek 45 VigorAP 700 User s Guide Enable Wireless Check this box to enable MAC address restriction If unchecked no Access Control restriction will be enforced any wireless client with proper encryp
28. elect 2 4GHz B G N Main SSID Please input the SSID the name used to identify this VigorAP 700 here You can input up to 32 alphanumerical characters PLEASE NOTE THAT SSID IS CASE SENSITIVE Site Survey When you use this access point as a wireless station for Ethernet network device to have wireless capability you have to associate it with a working access point Click Select Site Survey button then a Wireless Site Survey Table will pop up It will list all available access points nearby You can select one access point in the table It will join wireless LAN through this access point Please go to Section 2 4 2 1 for more information about the Wireless Site Survey Table After you finish with setting please click Apply and the following screen will be displayed Save setting successfully fou may press Continue to configure other settings or press Apply to restart the system for changes to take effect When you see this message the settings you made is successfully save You can click Continue to return to previous page and continue on other setting items or click Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds 2 4 2 1 Wireless Site Survey The table will list the access points nearby as the access point is set to Station mode You can select one of the access points to associate Dray Tek 21 VigorAP 700 User s Guide a http 192 168 1 2 Wireless Site Survey Micr
29. eral Connect using 8 Realtek RTL8029 AS PCI Ethernet Adapter Components checked are used by this connection EP Client for Microsof Retmoyks ja amp File and Printer Sharing for Mlagosoft Networks kI Internet Protocol TCP IP Se A of a lide T poco A A gon Se eee A e Install Uninstall Properties H Description KS S we Transmission Control Pratocol Internet Protocol T ratag wide area network protocol that provides communication across diverse interconnected networks IV Show icon in taskbar when connected 2 and click OK when finish IP address 192 168 1 9 Subnet Mask 255 255 255 0 General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings LC Obtain an IP address automatis ally LL C Use the following IP address S IP address ei Li Subnet mask Kat a Li Default gateway H E Li a a Li e Obtain DNS server addrestmmtermaioalyn n mm mn nn amnnnunu Use the following DNS server addresses Preferred DNS server Alternate DNS server VigorAP 700 User s Guide 10 Click Start button it should be located at lower left corner of your computer then click control panel Double click Network and Dial up Connections icon double click Local Area Connection and Local Area Connection Properties window will appear Select Se
30. eri ati aaa dako ano ca padan noon akolit dane 45 2 10 System DEES i a ok a e an kek ala Sic 47 2 10 1 Change PASSWONA k w siek kak ta ta n tt aa lt i ala e ka a sp ka l at tt aa 47 2 10 2 IP Address of the Wireless Access Point 48 2 103 wl sacii na za aia cai da den dep aaa c i da as d aaa dat aa c d d pano a dada acd a dala d das 49 2 11 Configuration Backup and Restore a cae cea ea n al i ka e a pa i pia e 51 2 12 Firmware I EE 52 Dr ay Te k vii VigorAP 700 User s Guide Ge OO SUA asters tan RR RE RR ee RR RR e Ni ak pini en RR ERE a epok dan ske area EEEE 53 Chapter III Troubleshooting mnnn ne eee ee 55 Appendix GIOSSaT Yoo ian gi iii ii rin iai ii 57 VigorAP 700 User s Guide viii Dray Tek Chapter I Product Information 1 1 Introduction Thank you for purchasing this VigorAP 700 With this high cost efficiency VigorAP 700 computers and wireless devices which are compatible with 802 1 In can connect to existing wired Ethernet network via this VigorAP 700 at the speed of 300Mbps Easy install procedures allows any computer users to setup a network environment in very short time within minutes even inexperienced users Just follow the instructions given in this user manual you can complete the setup procedure and release the power of this access point all by yourself Other features of this access point including e Compatible with IEEE 802 1 1b g n wireless network standard works with other
31. et Mask 255 255 255 0 You can press and hold Reset W PS button over 10 seconds to change the IP address back to default value if you forget the IP address you set To change IP address please click System Utility on the left The following screen will be displayed e Management IP USECH 192 165 1 2 ei ai AYE EI 255 255 255 0 Gateway Address 0 0 0 0 Bia Disabled ze Please input IP address and Subnet Mask in corresponding field and you can input the IP address of gateway in Gateway Address field if you need to manage this VigorAP 700 from other network like Internet If you want to activate the DHCP server function of this VigorAP 700 please select Enabled in DHCP Server option and see next Section for detailed instructions If you don t want to use DHCP server function of this VigorAP 700 or there s another DHCP server on the network this access point connects to please select Disable After you finish please go to the bottom of this page and click Apply The following screen will be displayed Save setting successfully You may press Continue to configure other settings or press Apply to restart the system for changes to take effect When you see this message the settings you made is successfully save You can click Continue to return to previous page and continue on other setting items or click Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds
32. iled descriptions of the function please refer to Section 2 4 1 1 Channel Please select a channel number you wish to use If you know a certain channel number is used by other VigorAP 700s nearby please refrain from using the same channel number Associated Clients Click Show Active Clients button and a new popup window will appear which contains the information about all wireless clients connected to this access point You can click Refresh button in popup window to keep information up to date After you finish with setting please click Apply and the following screen will be displayed Save setting successfully fou may press Continue to configure other settings or press Apply to restart the system for changes to take effect When you see this message the settings you made is successfully save You can click Continue to return to previous page and continue on other setting items or click Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds VigorAP 700 User s Guide 18 Dray Te k 2 4 1 1 Multiple SSID This access point supports four SSIDs Except the main SSID it can be configured in Basic Setting page you can configure another three of SSIDs here With different SSIDs you can separate the wireless networks with different SSID names WMM and VLAN settings Note If you want to configure the wireless security for different SSID please go to 2 7 Wireless Security for m
33. k Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds 2 7 5 802 1x Authentication You can enable 802 1x user identification based on RADIUS user authentication server by checking Enable 802 1x Authentication box when you select Disable or WEP as encryption type and the following screen will be displayed e Select SSID E BR le DrayTek ze e Security Settings Enable 802 1x Authentication Use internal MD5 PEAP RADIUS Server RADIUS Server IP address RADIUS Server 1212 RADIUS Server Password Here are descriptions of every setup item Enable 802 1x Authentication Enable or disable the use of 802 1x user authentication After you finish with setting please click Apply and the following screen will be displayed Dray Tek 41 VigorAP 700 User s Guide Save setting successfully You may press Continue to configure other settings or press Apply to restart the system for changes to take effect When you see this message the settings you made is successfully save You can click Continue to return to previous page and continue on other setting items or click Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds VigorAP 700 User s Guide 42 Dray Tek 2 8 Radius Server Comparing to other wireless security measures radius server provides user based authentication If
34. lect Use the following IP address then input the following settings in respective field Dray Tek 2 2 3 Windows XP IP address setup 1 Click Start button it should be located at lower left corner of your computer then click control panel Double click Network and Internet Connections icon click Network Connections and then double click Local Area Connection Local Area Connection Status window will appear and then click Properties 1e Local Area Connection Properties General Authentication Advanced Connect using E9 AMD PCNET Family PCI Ethernet Ad This connection uses the following items v S Client for Microsoft Networks dire and Printer Saiag for Microsoft Networks e MI JE QoS Packet Scheduler 94 n d Di Internet Protocol TCP IP AE EE Een K e a sa eo oo n ZS A Description Se a Ge Deseenneef Transmission Control Protocol lntemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks C Show icon in notification area when connected Notify me when this connection has limited or no connectivity 2 Select Use the following IP address then input the following settings in respective field and click OK when finish IP address 192 168 1 9 Subnet Mask 255 255 255 0 Internet Protocol TCP IP Properties General You can get IP settings assigned automatically if pour ne
35. left and the system status and information will be displayed as shown below _ Vig orAP D I Dray Tek 802 1 Tn Access Pomt e Home Basic Settings WPS Setting Advanced Settings Security RADIUS Server MAC Filtering System Utility Configuration Tool Firmware Upgrade Restart VigorAP 700 User s Guide Status and Information This page shows System Status Wireless Configuration and LAN Configuration information System Uptime Oday Oh 2m 23s Hardware Version Rev A Firmware Version 1 04 Mode AP SSID DrayTek Channel Number 11 Security Disable BSSID 00 50 7f 37 97 20 Associated Clients 0 LAN Configuration IP Address 192 168 1 2 14 Dray Tek Here are descriptions of every item System Uptime Displays the total passed time since the VigorAP 700 is powered Hardware Version Displays hardware version This information is helpful when you need online help from the dealer of purchase Firmware Version Displays current firmware version If you want to perform firmware upgrade this number will help you to determine if you need such upgrade Mode Displays current wireless operating mode see next Section SSID Displays current SSID the name used to identify this VigorAP 700 Channel Number Displays current wireless channel number Security Displays current wireless security setting BSSID Associated Clients Displays current BSSID a set of unique i
36. ly save You can click Continue to return to previous page and continue on other setting items or click Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds VigorAP 700 User s Guide 50 Dray Te k 2 11 Configuration Backup and Restore You can backup all configurations of this access point to a file so you can make several copied of access point configuration for security reason To backup or restore access point configuration please follow the following instructions Please click Configuration Tool on the left of web management interface and the following screen will be displayed on your web browser Configuration Tool Use the Backup button to download the VigroAP 700 s current configurations as a file You can then use the Restore button to restore the d configuration to VigorAP 700 Alternatively you can use the Factory Reset button to perform system restart and restore the factory default settings Backup Settings REES sr Restore to Factory Default Here are descriptions of every buttons Backup Press Backup button and you ll be prompted to download the configuration as a file default filename is config bin You can save it as another filename for different versions and keep it in a safe place Restore Press Browse to pick a previously saved configuration file from your computer and then click Restore to transfer the configuration file to access poi
37. n 8 2 2 2 Windows 2000 IP address seiup mean nana maneaua na anna 10 2 2 3 Windows XP IP address setup e men eee nenea aaa ana ana aaa 11 2 2 4 Windows Vista IP address setup mmm ana ame ana ana aee 12 2 2 5 Connecting to Web Management Interface 13 2 3 View System Status and Information ANNE 14 2 4 Select an Operating Mode for Wireless Access Point 16 APA AP MOG iia kantite ave wi ad oi a caca e air di tak ada ded apa no a d owa A a ati a ta Datu aid cedat 17 E E riet tie le 20 2 4 3 AP Bridge Point to Point Mode mmm eee ame aaa ana nnt 23 2 4 4 AP Bridge Point to Multi Point Mode men eee eee annene nnna 25 2 4 5 AP Bridge WDS Mode nenea nea ame nana nana aaa maneaua aaa manea rana 26 2 4 6 Universal ROPOALON a vie kana ad tan ki e n ask a ka n kk kk a a ks ye e a n kf tn kk e RI pp ik a da 28 2 5 WPS SOUL kwe wen eta online oaia a na dt ina Rat a be 0 30 2 6 Advanced Wireless Settings AEN 33 2 7 Wireless SOCUINIY sista intaia e io la Dal a pda Si la a a a i pt 35 2 1 Disable Security beer aici a a alt aa tt lt it Eat at ba ati at a ea 37 220 2 WE Point bu kdk jenes alora c page ad data atan k k d aaa dac ka etan a d d ag dota da ca ie Eta dai ga 37 2 7 3 WPA Pre shared hey nenea nea anemie nana 39 27 A WPA RADIUS nici teaca ca ata aie Gs a a k d ened Teele d at e AS 40 2 1 5 802 1x Authentic tioni si ia at eat ana dati aa la dA ala aa atat d aaa 41 2 8 EE 43 2 9 MAC Filtering bann la
38. nction Please click System Utility on the left of web management interface to access these functions Below are detailed descriptions of every control function 2 10 1 Change Password You can change the password that used to enter the web configuration menu of this VigorAP 700 Please click System Utility on the left and the following screen will be displayed e Password Settings Current Password New Password Confirm Password Please input current password in Current Password field then input new password in both New Password and Confirm Password field After you finish please go to the bottom of this page and click Apply The following screen will be displayed Save setting successfully You may press Continue to configure other settings or press Apply to restart the system for changes to take effect When you see this message the settings you made is successfully save You can click Continue to return to previous page and continue on other setting items or click Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds Dray Tek 47 VigorAP 700 User s Guide 2 10 2 IP Address of the Wireless Access Point You can change the IP address of this VigorAP 700 to make it becoming one part of your local network Please remember this address or you will not be able to connect the configuration menu of this VigorAP 700 Default IP address is 192 168 1 2 Subn
39. nd the remaining bits correspond to the host ID For example if the IP address for a device is in its binary form 11011001 10110000 10010000 00000111 and if its network mask is 11111111 11111111 11110000 00000000 It means the device s network address is 11011001 10110000 10010000 00000000 and its host ID is 00000000 00000000 00000000 00000111 This is a convenient and efficient method for access points to route IP packets to their destination ISP Gateway Address see ISP for definition The ISP Gateway Address is an IP address for the Internet access point located at the ISP s office ISP Internet Service Provider An ISP is a business that provides connectivity to the Internet for individuals and other businesses or organizations LAN Local Area Network A LAN is a group of computers and devices connected together in a relatively small area such as a house or an office Your home network is considered as LAN MAC Address MAC stands for Media Access Control A MAC address is the hardware address of a device connected to a network The MAC address is a unique identifier for a device with an Ethernet interface It is comprised of two parts 3 bytes of data that corresponds to the Manufacturer ID unique for each manufacturer plus 3 bytes that are often used as the product s serial number NAT Network Address Translation This process allows all of the computers on your home network to use one IP addre
40. nt After the configuration is uploaded the access point s configuration will be replaced by the file you just uploaded Factory Reset Click this button to remove all settings you made and restore the configuration of this access point back to factory default settings Dray Tek 51 VigorAP 700 User s Guide 2 12 Firmware Upgrade If there is new firmware of this VigorAP 700 available you can upload the firmware to the access point to change the firmware with new one to get extra functions To perform firmware upgrade please click Firmware Upgrade on the left of web management interface The following screen will be displayed Firmware Upgrade s page allows you to upgrade the VigorAP 70D s firmware It is recommended that upgrading the firmware fron wired stations Enter the path and name of the upgrade file and then click the Apply button below You will be prompted to confirm the upgrade Browse Click Browse button first You ll be prompted to provide the filename of firmware upgrade file Please download the latest firmware file from our website and use it to upgrade your access point After a firmware upgrade file is selected click Apply button The access point will start firmware upgrade procedure automatically The procedure may take several minutes please be patient Note Never interrupt the upgrade procedure by closing the web browser or physically disconnect your computer from access point If
41. ode In this mode this VigorAP 700 will connect to up to four VigorAP 700s which uses the same mode and all wired Ethernet clients of every VigorAP 700s will be connected together You can use this mode to connect a network to other networks which is physically isolated When you use this mode this access point is still able to accept wireless clients When you select AP Bridge WDS the following screen will be displayed Basic Settings This page allows you to define Mode Band and settings corresponding to the mode selected for the wireless connection Mode AP Brido 2 4 GHz B G N OI DrayTek Multiple SSID META 11 Associated Clients Show Active Clients Associated WDS AP Show WDS AP MAC address 1 BAKU MAC address 2 000000000000 o a MAC address 000000000000 MAC address 4 000000000000 Here are descriptions of every setup item VigorAP 700 User s Guide 26 Dray Tek Band Please select the wireless band you wish to use By selecting different band setting you ll be able to allow or deny the wireless client of a certain band If you select 2 4GHz B 2 4GHz N or 2 4GHz G only wireless clients using the wireless band you select 802 11b 802 11n or 802 11g will be able to connect to this access point If you select 2 4GHz B G then only wireless clients using 802 11b and 802 11g band will be able to
42. ode and input a long encryption passphrase every time when you need to setup a wireless client You only have to press a button on wireless client and this access point and the WPS will do the setup for you This access point supports two types of WPS Push Button Configuration PBC and PIN code If you want to use PBC you have to switch this access point to WPS mode and push a specific button on the wireless client to start WPS mode You can push Reset WPS button of this access point or click Start PBC button in the web configuration interface to do this if you want to use PIN code you have to provide the PIN code of the wireless client you wish to connect to this access point and then switch the wireless client to WPS mode The detailed instructions are listed follow Note WPS function of this access point will not work for those wireless clients do not support WPS To use WPS function to set encrypted connection between this access point and WPS enabled wireless client by WPS click WPS Setting on the left of web management menu and the following information will be displayed VigorAP 700 User s Guide 30 Dray Te k WPS Wi Fi Protected Setup Settings This page allows you to change the setting for W wireless client automatically connect to the Access Wi Fi Protected Setup WPS can help your Point Enable WPS e Wi Fi Protected Setup Information Unconfigured e Device Configuration Su POLE
43. ore information Z http 192 168 1 2 Multiple SSID Settings Microsoft Internet Explorer AR Multiple SSID This page allows you to configure the wireless settings for Multiple SSIDs The wireless security sofia 5 for ieee SSIDs can be configured in Security page Basic Setting Basic Setting Advanced Setting Enable VLAN ID D SSID1 M SSID2 Enable Disable vi SS Enable Enable w vi Disable vi Here are descriptions of every setup item No Except Main SSID you can configure additional three SSID here Enable Select the box to enable the different additional SSID SSID Please input the SSID name the name used to identify this VigorAP 700 here You can input up to 32 alphanumerical characters PLEASE NOTE THAT SSID IS CASE SENSITIVE Broadcast SSID Decide if the VigorAP 700 will broadcast its own SSID or not You can hide the SSID of your VigorAP 700 set the option to Disable so only people who know the SSID of your VigorAP 700 can get connected WMM WMM Wi Fi Multimedia technology which can improve the performance of certain network applications like audio video streaming network telephony VolP and others When you enable WMM function the access point will define the priority of different kinds of data to give higher priority to applications which require Dray Tek 19 VigorAP 700 User s Guide instant responding Therefore
44. osoft Internet Explorer Wireless Site Survey This page allows vou to scan any Access Point or IBSS available on wireless network You can Se SS Bana 2620 kyeh 00 50 7F 6C 38 18 TKIP WPAPSK QO 11b g n HW DrayTek 1 6 6 default 6 DrayTek 00 50 7F 90 24 18 NONE OPEN 0 11b g n TEST 00 50 7F 98 7B F6 TKIP WPAPSK 10 11b g n 00 14 4D 32 C0 CD NONE OPEN 5 Abi Here are descriptions of every setup item Select Click the radio button to select the access point Channel Display the channel number of the access point SSID Display the SSID name of the access point BSSID Display the BSSID MAC Address of the access point Encryption Display the encryption setting of the access points If you have selected the access point with security setting you have to go to 2 7 Wireless Security to set the same security with the access point you want to associate Authentication Display the authentication type of the access point Signal The signal strength of each access point will be displayed here The signal strength is stronger the connection quality is better Band Display the wireless modes including 11b 11b g or 11b g n or 11n only of the access points Refresh Click this button to refresh the table Connect Select an access point and click this button to choose the network The SSID name of the access point you have selected will be displayed in the Main SSID in the Basic Setting page Vigo
45. ower adapter please disconnect the access point and A C power adapter from utility power make sure it s safe before you re doing this and call your dealer of purchase for help VigorAP 700 User s Guide 56 Dray Tek Appendix Glossary Default Gateway Access point Every non access point IP device needs to configure a default gateway s IP address When the device sends out an IP packet if the destination is not on the same network the device has to send the packet to its default gateway which will then send it out towards the destination DHCP Dynamic Host Configuration Protocol This protocol automatically gives every computer on your home network an IP address DNS Server IP Address DNS stands for Domain Name System which allows Internet servers to have a domain name such as www Broadbandaccess point com and one or more IP addresses such as 192 34 45 8 A DNS server keeps a database of Internet servers and their respective domain names and IP addresses so that when a domain name is requested as in typing Broadbandaccess point com into your Internet browser the user will be sent to the proper IP address The DNS server IP address used by the computers on your home network is the location of the DNS server your ISP has assigned to you DSL Modem DSL stands for Digital Subscriber Line A DSL modem uses your existing phone lines to transmit data at high speeds Ethernet A standard for computer netwo
46. ption MWPA RADIUS GUME WPA TKIP OWPA2 AES OWPA WPAZ Mixed Use internal MD5 PEAP RADIUS Server RADIUS Server IP address RADIUS Server Port RADIUS Server Password 1812 Here are descriptions of every setup item WPA Mode You can select WPA encryption type here AES is safer than TKIP but not every wireless client supports it Please refer to the specification of your wireless client to decide which encryption type you should use Use internal MD5 Uses built in RADIUS Server refer to Section 2 8 instead of RADIUS Server external RADIUS server If you check this box the value in the following three fields will be ignored RADIUS Server IP Please input the IP address of RADIUS authentication server here address VigorAP 700 User s Guide 40 Dray Tek RADIUS Server Port Please input the port number of RADIUS authentication server here Default value is 1812 RADIUS Server Please input the password of RADIUS authentication server here Password After you finish with setting please click Apply and the following screen will be displayed Save setting successfully You may press Continue to configure other settings or press Apply to restart the system for changes to take effect When you see this message the settings you made is successfully save You can click Continue to return to previous page and continue on other setting items or clic
47. rAP 700 User s Guide 22 Dray Tek 2 4 3 AP Bridge Point to Point Mode In this mode this VigorAP 700 will connect to another VigorAP 700 which uses the same mode and all wired Ethernet clients of both VigorAP 700s will be connected together You can use this mode to connect a network to another network which is physically isolated Please note that when you set your access point to this mode it will not accept regular wireless clients anymore When you select AP Bridge Point to Point the following screen will be displayed Basic Settings 24 Ge Grota i a Go a ES 000000000000 Here are descriptions of every setup item Band Please select the wireless band you wish to use By selecting different band setting you ll be able to allow or deny the wireless client of a certain band If you select 2 4GHz B 2 4GHz N or 2 4GHz G only wireless clients using the wireless band you select 802 11b 802 11n or 802 11g will be able to connect to this access point If you select 2 4GHz B G then only wireless clients using 802 11b and 802 11g band will be able to connect to this access point If you want to allow 802 11b 802 11g and 802 11n clients to connect to this access point select 2 4GHz B G N Channel Please select a channel number you wish to use The channel number must be same with another VigorAP 700 you wish to connect Dray Tek 23 VigorAP 700 User s Guide MAC
48. rks Ethernet networks are connected by special cables and hubs and move data around at up to 10 100 million bits per second Mbps Idle Timeout Idle Timeout is designed so that after there is no traffic to the Internet for a pre configured amount of time the connection will automatically be disconnected IP Address and Network Subnet Mask IP stands for Internet Protocol An IP address consists of a series of four numbers separated by periods that identifies a single unique Internet computer host in an IP network Example 192 168 1 2 It consists of 2 portions the IP network address and the host identifier The IP address is a 32 bit binary pattern which can be represented as four cascaded decimal ce 99 numbers separated by aaa aaa aaa aaa In which each aaa can be anything from 000 to 255 or as four cascaded binary numbers separated by bbbbbbbb bbbbbbbb bbbbbbbb bbbbbbbb where each b can either be 0 or 1 A network mask is also a 32 bit binary pattern and consists of consecutive leading 1 is followed by consecutive trailing Us such as Dray Tek 57 VigorAP 700 User s Guide 11111111 11111111 11111111 00000000 Therefore sometimes a network mask can also be 66 described simply as x number of leading 1 is When both are represented side by side in their binary forms all bits in the IP address that corresponding to 1 in the network mask become part of the IP network address a
49. rmly secured Falling from high places would damage the access point and its accessories and warranty will be void Accessories of this access point like antenna and power supply are danger to small children under 3 years old They may put the small parts in their nose or month and it could cause serious damage to them KEEP THIS ACCESS POINT OUT THE REACH OF CHILDREN The access point will become hot when being used for long time This is normal and is not a malfunction DO NOT put this access point on paper cloth or other flammable materials There s no user serviceable part inside the access point If you found that the access point is not working properly please contact your dealer of purchase and ask for help DO NOT disassemble the access point warranty will be void If the access point falls into water when it s powered DO NOT use your hand to pick it up Switch the electrical power off before you do anything or contact an experienced electrical technician for help If you smell something strange or even see some smoke coming out from the access point or power supply remove the power supply or switch the electrical power off immediately and call dealer of purchase for help VigorAP 700 User s Guide 2 Dray Te k 1 3 Package Contents Before you starting to use this access point please check if there s anything missing in the package and contact your dealer of purchase to claim for missing items VigorA
50. s and Information Basic Settings This page shows System Status Wireless Configuration and LAN Configuration information WPS Setting Advanced Settings System Uptime Oday Oh 2m 23s Security Hardware Version Rev A RADIUS Server Firmware Version 1 04 Wireless Configuration MAC Filtering m ES ode System Utility SSID DrayTek Configuration Tool Channel Number 11 Security Disable BSSID 00 50 7f 37 97 20 Firmware Upgrade Restart Associated Clients 0 LAN Configuration IP Address 192 168 1 2 Dray Tek 13 VigorAP 700 User s Guide NOTE If you can t see the web management interface and you re prompted to input user name and password again it means you don t input username and password correctly Please retype user name and password again If you re certain about the user name and password you type are correct please go to 4 2 Troubleshooting to perform a factory reset to set the password back to default value 2 3 View System Status and Information After you connected to the access point by web browser the first page you will see is Status and Information All system and network related information of this access point will be displayed here The information is very helpful when you want to know the detailed information of your access point and when you try to fix the communication problem between this access point and other wired wireless computer devices You can click Home on the
51. se follow the following instruction to build the network connection between your new VigorAP 700 and your computers network devices 1 Connect VigorAP 700 to ADSL modem router or switch hub in your network through the LAN port of the access point by Ethernet cable 2 Connect a computer to ADSL modem router or switch hub Make sure the subnet IP address of the PC is the same as VigorAP 700 e g 192 168 1 X 3 Connect the A C power adapter to the wall socket and then connect it to the PWR connector of the access point Power on VigorAP and check all LEDs on the front panel PWR LED should be steadily on LAN LEDs should be on if the access point is correctly connected to the ADSL modem router or switch hub Power Adapter Dray Tek 7 VigorAP 700 User s Guide 2 2 Connecting to VigorAP 700 by Using Web Browser After the network connection is built the next step you should do is setup the access point with proper network parameters so it can work properly in your network environment Before you can connect to the access point and start configuration procedures your computer must be able to get an IP address automatically use dynamic IP address If it s set to use static IP address or you re unsure please follow the following instructions to configure your computer to use dynamic IP address For the default IP address of this AP is set 192 168 1 2 we recommend you to use 192 168 1 X except 2
52. setting successfully You may press Continue to configure other settings or press Apply to restart the system for changes to take effect When you see this message the settings you made is successfully save You can click Continue to return to previous page and continue on other setting items or click Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds 2 4 6 Universal Repeater In this mode the access point can act as a wireless repeater it can be Station and AP at the same time It can use Station function to connect to a Root AP and use AP function to service all wireless stations within its coverage Note For Repeater Mode this access point will demodulate the received signal check if this signal is noise for the operating network then have the signal modulated and amplified again The output power of this mode is the same as that of WDS and normal AP mode Basic Settings This page allows you to define Mode Band and settings corresponding to the mode selected far the wireless connection Mode EIES 2 4 GHz B G N ze GIE DrayTek Multiple SSID S IER 11 v Associated Clients Show Active Clients Associated Repeater AP Show Repeater AP Root AP SSID Here are descriptions of every setup item Band Please select the wireless band you wish to use By selecting different band setting you ll be a
53. ss Using the broadband access point s NAT capability you can access the Internet from any computer on your home network without having to purchase more IP addresses from your ISP Port Network Clients LAN PC uses port numbers to distinguish one network application protocol over another Below is a list of common applications and protocol port numbers Application Protocol Port Number VigorAP 700 User s Guide 58 Dray Te k Telnet FIP SMTP POP3 H 323 SNMP SNMP Trap HTTP PPTP TCP TCP TCP TCP TCP UCP UDP TCP TCP PC Anywhere TCP PC Anywhere UDP 23 21 25 110 1720 161 162 80 1723 5631 5632 PPPoE Point to Point Protocol over Ethernet Point to Point Protocol is a secure data transmission method originally created for dial up connections PPPoE relies on two widely accepted standards Ethernet and the Point to Point Protocol It is a communications protocol for transmitting information over Ethernet between different manufacturers Protocol A protocol is a set of rules for interaction agreed upon between multiple parties so that when they interface with each other based on such a protocol the interpretation of their behavior is well defined and can be made objectively without confusion or misunderstanding Access point An access point is an intelligent network device that forwards packets between different networks based on network layer address information such as IP addresses Subnet Mask
54. t are out please check the If encryption is enabled please check WEP or WPA passphrase settings on your wireless client again Unplug the power plug of access point and plug it back again after 10 seconds status of A C power adapter and make sure it s correctly 55 VigorAP 700 User s Guide powered I can t locate my access point by my wireless client Check if Broadcast SSID is set to off Is Antenna properly installed and secured Are you too far from your access point Try to get closer Please remember that you have to input SSID on your wireless client manually if SSID broadcast is disabled File download is very slow or breaks frequently Try to reset the access point and see if it s better after that Try to know what computers do on your local network If someone is transferring big files other people will think Internet is really slow Change channel number and see if this works I can t log onto web management interface password is wrong Make sure you re connecting to the correct IP address of the access point Password is case sensitive Make sure the Caps Lock light is not illuminated If you really forget the password do a hard reset Access point become hot This is not a malfunction if you can keep your hand on the access point s case If you smell something wrong or see the smoke coming out from access point or A C p
55. the firmware you uploaded is corrupted the firmware upgrade will fail You may have to return this access point to the dealer of purchase to ask for help Warranty voids if you interrupted the upgrade procedure VigorAP 700 User s Guide 52 Dray Te k 2 13 Restart When you think the access point is not working properly you can use this function to restart the access point This may help and solve the problem This function is useful when the access point is far from you or unreachable However if the access point is not responding you may have to switch it off by unplugging the power plug and plugginh it back again after 10 seconds To restart your access point please click Restart on the left The following screen will be displayed Restart In the event that the system stops responding correctly or stops functioning you can perform a Restart Your i jed To perform the restart click on the Apply button below You will be asked to confirm your decision The Restart will be complete when the LED Power light stops blinking Please click Apply A popup message will ask you again to make sure you really want to restart the access point Microsoft Internet Explorer 2 Do you really want to restart the Access Point Cancel Click OK to reset the access point or click Cancel to abort Please remember all connections between wireless clients and this access point will be disconnected Dray Tek 53 VigorAP
56. tication 8 Choose Encryption mode from the drop down list for the wireless operating mode selected with AP Bridge Point to Point AP Bridge Point to Multi Point or AP Bridge WDS There are four types of security level you can select Disable no security data encryption disabled WEP WPA Pre shared Key and WPA Radius Please refer to the following sections for detailed instructions Dray Tek 35 VigorAP 700 User s Guide Security This page allows you to setup the wireless security To prevent any unauthorized access to your wireless network please turn on WEP or WPA encryption e Select SSID SSID choice e Security Settings MY Disable TT Enable 802 1x Authenticati WEP WPA pre shared key WPA RADIUS DrayTek Disable Cancel Note If you have enabled Multiple SSID function please select the SSID network you wish to configure in advance Please remember it s very important to set wireless security settings properly Without a proper setting hackers and intruders may gain access to your local network and do something bad to your computers and servers which could cause serious problem There are several things you can do to improve wireless security 1 Always enable data encryption Only disable it when you want to open your VigorAP 700 to the public 2 Never use simple words as encryption password Use the random combination of symbols numbers and alphabets
57. tion setting will be able to connect to this VigorAP 700 MAC address Input MAC address allowed using this VigorAP 700 here You don t have to add colon or hyphen by yourself just input 0 to 9 and a to f here like 112233445566 or aabbccddeeff Comment You can input any text here as the comment of this MAC address like ROOM 2A Computer or anything You can input up to 16 alphanumerical characters here This is optional and you can leave it blank However it is recommended to use this field to write a comment for every MAC addresses as a memory aid This is optional Add When you finish inputting MAC address and optional Comment click this button to add the MAC address to the list Clear Remove all characters in MAC address and Comments fields After you finish with setting please click Apply and the following screen will be displayed Save setting successfully You may press Continue to configure other settings or press Apply to restart the system for changes to take effect When you see this message the settings you made is successfully save You can click Continue to return to previous page and continue on other setting items or click Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds VigorAP 700 User s Guide 46 Dray Te k 2 10 System Utilities This access point provides some control functions include password IP address management and DHCP server fu
58. tween 802 11 b g n wireless devices and wired Ethernet network and exchanges data between them When you select AP the following screen will be displayed Basic Settings This page allows you to define Mode Band and settings corresponding to the mode selected for the wireless connection aen W OI DrayTek Multiple SSID Associated Clients Show Active Clients Here are descriptions of every setup item Band Please select the wireless band you wish to use By selecting different band setting you ll be able to allow or deny the wireless client of a certain band If you select 2 4GHz B 2 4GHz N or 2 4GHz G only wireless clients using the wireless band you select 802 11b 802 1 In or 802 11g will be able to connect to this access point If you select 2 4GHz B G then only wireless clients using 802 11b Dray Tek 17 VigorAP 700 User s Guide and 802 11g band will be able to connect to this access point If you want to allow 802 11b 802 11g and 802 11 n clients to connect to this access point select 2 4GHz B G N Main SSID Please input the SSID the name used to identity this VigorAP 700 here You can input up to 32 alphanumerical characters PLEASE NOTE THAT SSID IS CASE SENSITIVE Multiple SSID The access point supports multiple SSID function up to four SSIDs can be set If you want to configure additional SSIDs please click this button For deta
59. twork supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically lise ths E IP addens Etenn ll ss 192 168 1 3 Btoet mask 255 255 255 0 Default gateway BLL D k D Use the following DNS server addresses Preferred DNS server Alternate DNS server LON n n ne neni Dray Tek 11 VigorAP 700 User s Guide 2 2 4 Windows Vista IP address setup 1 Click Start button it should be located at lower left corner of your computer then click control panel Click View Network Status and Tasks then click Manage Network Connections Right click Local Area Netwrok then select Properties Local Area Connection Properties window will appear select Internet Protocol Version 4 TCP IPv4 and then click Properties Er Intel R PRO 1000 MT Network Connection This connection uses the following items wi E Client for Microsoft Networks MI ji QoS Packet Scheduler 950 me Sr Panter Sharing Tor PRRS0TeNete age E IS intemet Protocol Version 6 TCP IPv6 Intemet Protocol Version 4 TCP Py4 D Ae a Link Layer Topology Discov lapper LO Driver Link Layer Topology Discovery eeeeeeeas sou pan e X S D pakse i Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse inter
60. ubject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment Federal Communication Commission FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment In order to avoid the possibility of exceeding the FCC radio frequency exposure limits human proximity to the antenna shall not be less than 20cm 8 inches during normal operation The antenna s used for this transmitter must not be co located or operating in conjunction with any other antenna or transmitter R amp TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999 5 EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity R amp TTE The R amp TTE Directive repeals and replaces in the directive 98 13 EEC Telecommunications Terminal Equipment and Satellite Earth Station Equipment As of April 8 2000 Safety This equipment is designed with the utmost care for the safety of those who install and use it However special attention must be paid to the dangers of electric shock
61. y setup item WPA Unicast Cipher Available options are WPA TKIP WPA2 AES and Suite WPA WPA2 Mixed You can select one of them but you have to make sure your wireless client support the cipher you selected Pre shared Key Please select the format of pre shared key here available options are Format Passphrase 8 to 63 alphanumerical characters and Hex 64 hexadecimal characters 0 to 9 and a to f Pre shared Key Please input pre shared key according to the key format you selected here For security reason don t use simple words After you finish with setting please click Apply and the following screen will be displayed Dray Tek 39 VigorAP 700 User s Guide Save setting successfully You may press Continue to configure other settings or press Apply to restart the system for changes to take effect When you see this message the settings you made is successfully save You can click Continue to return to previous page and continue on other setting items or click Apply button to restart the VigorAP 700 The changes will take effect after about 30 seconds 2 7 4 WPA RADIUS WPA Radius is the combination of WPA encryption method and RADIUS user authentication If you have a RADIUS authentication server you can check the identification of every wireless client by user database When you select WPA RADIUS as encryption type the following screen will be displayed e Security Settings Encry
62. you can improve the performance of such network applications VLAN ID If your network uses VLANS you can assign the SSID toa VLAN O Untagged on your network Client devices that associate using the SSID are grouped into this VLAN The VLAN ID range is from 1 to 4094 The VLAN ID is O by default it means disabling the VLAN function for the SSID 2 4 2 Station Infrastructure In this mode you can connect the access point to Ethernet device such as TV and Game player to enable the Ethernet device as a wireless station and join to a wireless network through an access point or AP router Basic Settings This page allows you to define Mode Band and settings corresponding to the mode selected for the wireless connection O BEE GEDE DrayTek Here are descriptions of every setup item Band Please select the wireless band you wish to use By selecting different band setting you ll be able to allow or deny the wireless client of a certain band If you select 2 4GHz B 2 4GHz N or 2 4GHz G only wireless clients using the wireless band you select 802 11b 802 11n or 802 11g will be able to connect to this access point If you select 2 4GHz B G then only wireless clients using 802 11b and 802 11g band will be able to connect to this access point If you want to allow 802 11b 802 11g and 802 11n clients to VigorAP 700 User s Guide 20 Dray Tek connect to this access point s
63. your wireless client supports 802 1x user authentication you can use the Radius Server function to use the internal mini radius server to improve security and wireless user control Note Please note that the internal Radius server only supports MD5 PEAP method You must check if your wireless client s supports it or not The internal radius server supports 96 users and 16 IP addresses If the number of user and or IP address you need is more than this please use external radius server To setup internal radius server click Radius Server on the left of web management interface and the following information will be displayed Radius Server Enable Radius Server Users Profile up to 96 users Kou nomen monn Authentication Client up to 16 clients 3 INTE IC A CI Here are descriptions of every setup item Enable Radius Server Check this box to enable internal radius server function User Profile You can add or delete radius user here Please input username password confirm password in corresponding field and click Add button to add the user to radius server database You can click Dray Tek 43 VigorAP 700 User s Guide Cancel to clear the text you typed in above three fields All current radius users will be listed here If you want to delete one or more users check the box of that user and click Delete Selecte

Draytek VigorAP 700

Contents

Download Pdf Manuals

Related Search

Related Contents