Baumatic BWD12.1 washer dryer
Contents
1. Y The water inlet hose will be inside the drum of your washing machine when you receive the appliance Y Connect and fully tighten the inlet hose to the threaded inlet valve that is located at the rear of the washing machine You should connect the end with the right angle connector on it to the back of your appliance Y Connect the other end of the inlet hose to your mains water supply 33 IMPORTANT There should be a filter sitting inside the end of the inlet hose that connects to your mains water supply The inlet hose may leak if this filter is missing This filter is supplied with the appliance you should contact Baumatic to obtain one if it is missing Y Tighten the inlet hose to your mains supply fully but do not over tighten as this may distort the filter that sits in the end of the inlet hose Y Test for any leaks Water outlet Y Secure the drain hose so that it cannot move whilst the washing machine is in use Y Place the end of the drain hose on your drain pipe Push it a short way down into your drain pipe Y IMPORTANT Do not insert the drain hose too deeply into the water pipe as this may cause siphoning v NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL LENGTH Fitting the furniture door o Please refer to the building in template for instructions on how to fit your integrated appliance and connect the furniture door to the product 34 Power supply IMPORTANT As2. Instruction manual USER MANUAL FOR YOUR BAUMATIC BWD12 1 Fully integrated washer dryer 3 Baumatic You will be mine NOTE This User Instruction Manual contains important information including safety amp installation points which will enable you to get the most out of your appliance Please keep it in a safe place so that it is easily available for future reference DD 06 05 08 Contents Environmental note Important safety information Specifications Description of the appliance Control panel Program options LCD display Detergent drawer Preparing the wash cycle Preparing your garments for washing A selection of wash care symbols Detergents and conditioners Program table Wash program guidance Selecting a wash program Selecting a separate drying program Selecting an automatic wash and dry program Cancelling or pausing a wash program Delay start feature Spin reduction button Setting a program option Child lock Maintenance and cleaning In daily use Control panel and washing machine cabinet Detergent drawer The washing machine drum Door gasket Error code failure system General troubleshooting Poor wash results Cleaning the drain pump filter Installation Unpacking and removing the transit bolts Positioning and levelling the appliance Connecting to the mains water supply Water outlet Fitting the furniture door Power supply Before first use mainte
3. Washing machine vibrates during the spin cycle o Check that the transport locking devices have been removed see installation instructions o Make sure that the washing machine is installed on a flat and level floor o Ensure that all four feet are resting firmly on the floor by pressing down on each corner and making sure that the appliance is stable o Ifitis unstable then follow the Positioning and leveling the appliance section Poor spin results o Clean the drain pump see Cleaning the drain pump filter section Water in the detergent dispenser o Although there will be some water residue left in the detergent drawer after a wash cycle has completed If the drawer is full of water then you may need to clean the detergent drawer 27 IMPORTANT Your appliance has an unbalance control system If this system detects that the washload is unevenly distributed inside the drum Your washing machine will try to redistribute the load before spinning If after several attempts it is unable to redistribute the washload then the appliance will either spin at a slower speed or skip the spin cycle and drain Uneven load distribution can be caused by too large a wash load or too small a wash load It can also occur if a single item if washed inside the appliance Poor wash results My garments are looking grey and there are limescale deposits present in the drum of my washing machine There is not enough deter
4. paperclips safety pins etc Zips should be closed duvet covers and pillow cases should be buttoned up and any loose straps should be tied up This will help to prevent other garments from getting damaged during the wash Woollens and knitted coloured fabrics should be turned inside out before being washed in the appliance Small delicate items tights baby socks should be placed in either a washing net or a zipped pillow case Bras suitable for machine washing that contain a wire should also be washed in this manner Curtains should be handled with particular care All plastic hooks or metal strips must be removed before being washed in the appliance Coloured items and whites should be washed in separate wash cycles New garments often contain an excess of dye therefore it is advisable to wash them separately for their first wash Garments should be unfolded and shook out before being placed inside the machine A selection of wash care symbols Washing boiling normal normal Do not temp 95 C temp 60 C temp 40 C delicate gt e II Dry cleaning 30 Do not clean Do not dry Jal Do not iron all solvents all but TR lll Spin dryer IV Ironing low 150 C nu A Select a programme taking into account the care labels indications o The wash care symbols should be used to help you to select the most suitable wash program They will also hel
5. you purchased the product IMPORTANT SAFETY INFORMATION Your safety is of the utmost importance to Baumatic Please make sure that you read this instruction booklet before attempting to install or use the appliance If you are unsure of any of the information contained in this booklet please contact the Baumatic Technical Department General Safety Repairs to your appliance must only be carried out by a Baumatic engineer or one of its authorised service agents Any attempt by an inexperienced person to repair the appliance could result in injury or damage to your washer dryer If you notice that the mains cable is damaged The appliance must not be used The same applies if you notice that the worktop control panel or base areas are damaged As this could allow access to the internal components of the machine The appliance should be turned off and isolated from the mains supply before either cleaning or maintenance work is attempted The mains cable must not be used to pull the plug out of the electrical socket The machine should not be sprayed with water The glass of the porthole door may become hot during the higher temperature wash programs The machine should be allowed to cool before carrying out an emergency drain or cleaning the drain filter It is possible for small animals to chew either mains cables or water hoses which could cause an electric shock hazard or leak Installation O O Th
6. your appliance is a built in product the electrical socket must still be accessible once the appliance is installed Y Consult the rating plate located on the inner rim of the porthole door of the appliance BEFORE making the electrical connections Ensure that the voltage reaching the plug is the same as that on the rating plate v DO NOT REMOVE THE RATING PLATE AS THE INFORMATION ON IT IS IMPORTANT Y The moulded plug that is supplied with the appliance must be placed into an earthed and insulated socket Y Broken or damaged power leads must only be replaced by a suitably qualified person A power lead of a similar type must be used in replacement Y Power lead type HOVV F 3G 1 5 Y IMPORTANT We do not recommend that this appliance is connected to an extension lead 35 Before first use maintenance wash o Select a Normal 90 C wash program When your washing machine has been correctly installed we recommend that you perform a maintenance wash cycle This will check that all aspects of the installation are correct it will also remove any deposits that may have been left on the drum by the manufacturing process o A small quantity of detergent should be used during this maintenance wash Certificate of compliance C Compliance with the following Directives 73 23 EEC 89 336 EEC 92 75 EEC The Manufacturer declares that its product complies with the general safety hygienic and environme
7. INSTRUCTION MANUAL YOU SHOULD KEEP THE TRANSIT PACKAGING IN CASE YOU NEED TO TRANSPORT THE MACHINE IN THE FUTURE Unpacking the machine and removing the transit bolts Y Remove the base corner protection pieces and top cover Y Locate the three transit bolts that secure the drum in position whilst the appliance is being transported Y Using a screwdriver unscrew the three plastic transit bolt covers Y Loosen and remove the three transit bolts 31 Y Using a screwdriver refit the three plastic transit bolt covers that you removed previously IMPORTANT The transit bolts MUST be removed before your washing machine is used for the first time Positioning and leveling the appliance Y Place the washing machine on a solid and level floor surface v DO NOT PLACE THE WASHING MACHINE ON A CARPET Y Loosen the adjustable feet that are positioned on the base of the appliance Y Slacken off the lock nut on each of the washing machine feet using a spanner Y Adjust the feet to level off the washing machine 32 Y Once levelled correctly you should tighten the lock nut back up on each of the washing machine feet using a spanner IMPORTANT When the washing machine is positioned in the location where it will be used Make sure that all four feet are resting firmly on the floor by pressing down on each corner and checking that the appliance stands still Connecting to the mains water supply
8. am once a wash cycle is in progress you should turn the program selection knob The appliance will go onto PAUSE status and the wash program will be cancelled The door will remain locked for two minutes before it is possible to open the door and take out the garments Before opening the porthole door you MUST drain the appliance otherwise there may still be water in the drum when you open the door o Itis also possible to put the machine into PAUSE status by pressing the START STOP button whilst the wash cycle is in progress However this will not cancel the wash program and to restart the wash cycle you should press the START STOP button again Delay start feature Your appliance has a delay start feature which allows you to pause the start of a wash cycle until a later time v Follow the process listed under Selecting a wash program Y Before pressing the START STOP button you should select the length of time that you want to delay the wash program for by pressing the delay start button o Each time the delay start button is pressed the start of the wash cycle will be delayed by one hour The LCD display will show how many hours the wash cycle is being delayed for in the bottom right hand corner o Press the START STOP button o To cancel a time delay that has been set you should press the delay start button successively Once 24 hours shows on the LCD display you need to press the delay start butto
9. as been cancelled Maintenance and cleaning In daily use v Once a wash cycle has completed you should pull out the detergent drawer slightly so it can dry out Y Leave the porthole door ajar for a short while after a wash cycle has completed This should help to prevent stagnant smells and to protect the door seal Y Close the water tap v We suggest that you disconnect the appliance from your mains supply when it is not in use Control panel and washing machine cabinet IMPORTANT Do not use any abrasive cleaner or household polish on either the control panel or operating parts Y Wipe over the control panel and the external surface of the machine using a brand new damp cloth with warm water Y If you ever spill any liquid detergent or conditioner from the detergent drawer onto the washing machine cabinet then these should be cleaned up immediately as they could be corrosive 24 Detergent drawer Occasionally the detergent drawer should be cleaned o Pull the detergent drawer out as far as it will go and then remove the drawer by pulling firmly o Use warm water and a brush to thoroughly clean the three compartments of the detergent drawer o Clean the area that the detergent drawer slides into with a brush o You should also clean the siphon that sits inside of the conditioner P section of the detergent drawer Taking care to make sure that the siphon is inserted back in the drawer corr
10. dispenser Stainless steel drum Drain pump filter flap Rating plate Control panel START STOP button LCD display Drying time button Wash program i Detergent drawer i Spin Delay Program i eee selection start option button button Wash program selection knob This control knob allows you to select the wash program of your choice To activate it you should press in the program selection knob to pop out the control Start Stop button Once a wash program has been selected this button should be pressed to start the wash cycle Program option button This button needs to be pressed after a wash program has been selected but before the wash program has been started If you select a different wash cycle after pressing a program option it will need to be reselected Extra rinse This function increases the level of the final rinse for the selected wash program This should be selected if large loads are being washed or the garments belong to somebody who has sensitive skin This option will increase the amount of water the appliance uses Easy iron This function helps to prevent garments from creasing by carrying out a program where the rotation of the drum will fluff out the garments after the spin cycle has completed This should make the garments easier to iron Intensive wash This function should be selected if you are washing heavily soiled stained clothes It achieves a better level of wa
11. e installation instructions contained within this user manual must be followed It is obligatory for the completed installation to comply with all relevant building regulations and local water authority requirements Before the first use of the appliance we advise that a 90 degree cotton wash is completed No garments should be placed inside the machine however a small amount of detergent must be used During Use It is recommended that the appliance is unplugged and the water supply is turned off after the machine is used This appliance is only designed to wash normal domestic washloads If you use your washing machine in any other way or it is incorrectly used then Baumatic accepts no liability for any damage that might be caused and any guarantee will be void No attempt should be made to alter or modify the specifications of this appliance The detergents that you place in this appliance should be suitable for automatic washing machines With regards to dosage levels the detergent manufacturer s recommendations should be followed You should not wash garments that have been in contact with flammable materials Your washing machine should not be used for dry cleaning If you use either dyes or bleaching agents inside this machine then you should consult with the manufacturer of these products to make sure they are suitable for use in your washing machine Baumatic cannot be held responsible for any damage that may re
12. ectly o Replace the detergent drawer by placing it back into the slot Then push the drawer fully back into position The washing machine drum The drum of your washing machine is constructed from stainless steel However if there are objects that can rust placed inside the drum then it is possible for the drum to become stained IMPORTANT Do not use a descaling agent iron steel wool or scouring agents to clean the drum of your appliance v Remove any rust stains on the drum with an appropriate stainless steel cleaning agent 25 Door gasket Y You should regularly check to see if any deposits have formed or there are any foreign bodies in the rubber door gasket This sits inside the opening of the porthole door Error code failure system If your appliance senses that it is not operating correctly then an error code may appear in the LCD display The following error codes can possibly be remedied by the customer and the steps outlined below should be followed BEFORE COMPLETING ANY MAINTENANCE ON THE APPLIANCE IT SHOULD BE DISCONNECTED FROM YOUR MAINS POWER SUPPLY No display o Power failure o Check that the power plug is in the mains socket correctly o Check the mains fuse FO1 No water coming into the machine o Check the water pressure of your mains water supply o Clean the mesh filter that sits in the inlet hose o Make sure the water tap that the machine is connected to is turned on full
13. ent that you are using agent the recommendations of the When using any detergent or water softening A manufacturer should be followed S6 Scit souqej pexiuyogeuju g Kap aq Si o a o m wm xvuo oL eyeoueproneuu s XIW UOPOOUOPOD uids jeuy e ua e pue pappe ji Jeuoqipuoo uj sesuu use JOON 3 g jos 401 sJnoJoo ajeouep xiu uonooyoneuu S uids jeuy Buoj e pue peppe ji JSuonpuoo uy Jn0JOO S8ej S9S uM SeSUu use uuou useaeJd ueuryuono e E en ge HOS WOH SJnOJOO 9181p 0 uuo ueuryuono OE I N AA O 0 PND Jn0j09 38189116P Poo pjo j euuoN ueuruono eunueJjboug amp 8 88 2 n ang S3AS3A ON S3 weupedwoo By S3A z Eg T aF yonpoud 9109 Jo Si usc Peo xew suopnq vondo asd 15 NOTE the KWh and litre consumptions and program durations may vary depending on the type and amount of clothes being washed your mains water pressure etc Program for wash and energy consumption assessment in accordance with standard EN60456 press intensive wash button Wash program guidance o A particular program option can only be selected if the program table advises that it is possible with the wash cycle you have selected o The washing machine automatically selects a spin speed for a particular wash program However it is possible to reduce the spin speed by using the spin red
14. gent being added The incorrect detergent is being used Stains are not being pre treated The correct wash program or wash temperature was not selected O OO 0 I have followed the advice given above but my garments are still coming out with grey stains on them o The garments are soiled with oils ointments or grease and were washed without enough detergent o The wash temperature selected was too low o Fabric conditioner has come into contact with the garments If this happens try to wash out these stains as quickly as you can and try to avoid getting conditioner on the garments in future After the final rinse I can still see foam o Modern detergents can result in there still being foam in the final rinse this does not mean that the washing is not being rinsed properly 28 There is white residue on my garments when I remove them from the appliance o Modern detergents can contain insoluble contents and white residue after a wash cycle is not necessarily a sign of the garments not being rinsed properly o You should shake out the garment or brush it off In future possibly turn the garment inside out before it is washed You may wish to move from a powder detergent and switch to a liquid detergent instead Cleaning the drain pump filter IMPORTANT Switch off your washing machine and disconnect the plug from your mains supply You should clean out the filter approximately every twenty was
15. hat you select will affect the length of time the wash cycle will take to complete The LCD display will update to reflect this change v Press the START STOP button 22 o The program option button needs to be pressed after a wash program has been selected but before the wash program has been started If you select a different wash cycle after pressing a program option it will need to be reselected o Any program option can be selected once the wash cycle is already in progress providing that the stage in the wash cycle that the option will affect has not already been passed E g you cannot select an intensive wash once the machine has reached the rinse stage of the wash cycle Child lock Your appliance has a child lock option if this is set it will mean that nobody can affect the operation of the wash program once it has started The child lock should be activated once a wash program has been selected and any program options that you wish to use o To activate the child lock you should hold down the START STOP button for at least three seconds When the child lock is set a a symbol will appear on the LCD display o The child lock option will end once the wash cycle completes 23 o If you want to cancel the child lock option before the wash program completes You should hold down the START STOP button for at least three seconds When the symbol disappears from the LCD display the child lock option h
16. hes If the drain pump filter is not cleaned regularly then your appliance may find it difficult to pump out water efficiently Use a coin to turn the filter cap Pull out the filter cap Place a container under the drain pump filter to collect any excess water that may come out of the drain pump when it is removed 29 Turn the filter a quarter turn anti clockwise water will start to come out of the drain pump Continue to turn the filter anti clockwise until you reach a half turn more water will come out of the drain pump When all the water has drained out of the washing machine turn the filter several times anti clockwise until it can be removed completely Remove the filter and rinse out the filter under the tap Remove any debris from the filter Remove any debris that is in the area of the appliance that you removed the drain pump filter from Screw the filter clockwise back into position making sure that it is fully tightened You should keep turning until you cannot turn it any further Refit the filter cap IMPORTANT Do not perform this operation if the appliance has stuck on a cycle until the water inside the machine has cooled sufficiently Otherwise the water that comes out of the drain pump filter may still be hot 30 Installation IMPORTANT THIS INSTALLATION MUST BE COMPLETED BY A SUITABLY QUALIFIED PERSON BAUMATIC ONLY SANCTION THE INSTALLATION GIVEN IN THIS
17. letes the last rinse the B symbol will flash and the drum will rotate approximately every 3 minutes Y Press the spin reduction button until the spin speed that you require appears in the LCD display then press the START STOP button 21 Y If you want the appliance to drain only press the spin n reduction button until the C symbol appears in the LCD display then press the START STOP button OPENING THE DOOR OF THE APPLIANCE OTHERWISE YOU COULD OPEN THE PORTHOLE DOOR WHILST THERE IS STILL WATER IN THE DRUM YOU MUST DO ONE OF THESE STEPS BEFORE You should ensure that the garments you are washing are suitable for suspending in water before selecting this option Garments should not be suspended in water for a prolonged period Setting a program option o There are three program options that you can select providing that the wash program chart indicates that a particular option can be selected with a particular wash program uW i tt pa o To select a program option m es you should press the 1100 0 58 be selection button until the neon comes on next to the program option that you want o By pressing the select WwW ow EQ button several times you 4 can choose between Pay 198 D 58 e several combinations of program option One two or three program options can be selected at a time depending on the wash program that you have selected o Any program option t
18. n minutes by using the drying time button o The drying time will appear on the LCD display and will increase each time the drying time button is pressed o Press the START STOP button to get the drying cycle to commence Selecting an automatic wash and dry program Y Y Activate the pop out program selector knob by depressing it Select the most appropriate wash program for the garments that you are washing by turning the program selector knob The LCD display will briefly flash the wash program number that you have selected and then show the approximate time that it will take the chosen wash cycle to complete Select any program options by using the program option button underneath the LCD display for more information please refer to the setting a program option section Any program option that you select will affect the length of time that the wash cycle will take to complete The LCD display will update to reflect this change Select the drying time in minutes by using the drying time button The drying time will appear on the LCD display and will increase each time the drying time button is pressed Press the START STOP button to get the automatic wash and dry cycle to commence IMPORTANT If you select a wash and dry program your wash load must not be over 4kg for NORMAL wash programs and 1 5kg for DELICATE wash programs Cancelling or pausing a wash program Y O O To stop a wash progr
19. n one further time and the delay start will be cancelled o If you alter the wash program whilst a delay start has been set this will also cancel the delay start Spin reduction button Your washing machine will automatically select an appropriate spin speed for each wash program However it is possible to decrease the spin speed that it automatically selects by pressing the spin reduction button Y Turn the wash program selection knob to the wash program that you want to use 20 wo o me m 1000 0 58 e v Press the spin selection button and the spin speed will reduce in 100 rpm increments o Itis possible to reduce the spin speed from the one automatically selected by the wash program down to 400rpm v If you continue to press the spin reduction button after 400rpm appears Then will appear in the LCD display This means that the No spin option has been selected and at the end of the wash cycle the machine will not spin at all and the wash program will finish after it has drained v If you press the spin reduction button again then B will appear in the LCD display This means that the Anti crease option has been selected The clothes will be held in water until you select a spin or drain program Y This feature is useful if you are not going to be present when the wash cycle completes as it will lessen the chance of the garments becoming creased v After the appliance comp
20. nance wash Contact details 26 27 28 29 31 31 32 33 34 34 35 36 37 18 20 22 23 24 s 26 27 28 29 30 36 32 33 34 ENVIRONMENTAL NOTE Note Before discarding an old appliance switch off and disconnect it from the power supply Cut off and render any plug useless Cut the cable off directly behind the appliance to prevent misuse This should be undertaken by a competent person Disable the door lock to make sure that children cannot get stuck inside the appliance This appliance is marked according to the European directive 2002 96 EC on Waste electrical and Electronic Equipment WEEE By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product em The symbol on the product or on the documents accompanying the product indicates that this appliance may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment Disposal must be carried out in accordance with local environmental regulations for waste disposal For more detailed information about treatment recovery and recycling of this product please contact your local city office your household waste disposal service or the shop where
21. ntal protection requirements pursuant to the European Community Directives and that the specific documents applicable to the said product especially the European Community Declaration of Conformity issued by the manufacturer may be viewed in offices of the competent authorities and may be obtained through the Manufacturer 36 oo i aumatic You will be mine United Kingdom Baumatic Ltd Baumatic Buildings 6 Bennet Road Reading Berkshire RG2 0QX United Kingdom Sales Telephone 0118 933 6900 Sales Fax 0118 931 0035 Service Telephone 0118 933 6911 Service Fax 0118 986 9124 Spares Telephone 01235 437244 Technical Advice Telephone 0118 933 6933 E mail sales baumatic co uk technical baumatic co uk Website www baumatic co uk Republic of Ireland 01 6266 798 Czech Republic Baumatic CR spol s r o Amperova 495 46215 Librec Czech Republic 420 800 185 263 www baumatic cz Slovak Republic Baumatic Slovakia s r o Skultetyho 1 831 04 Bratislava 3 Slovakia 421 255 640 618 Germany Baumatic Gmbh Janderstrasse 9 Mannheim 68199 Germany 4962 112 9190 www baumatic de Italy Baumatic Italia S R L Via Caltana 129 Campodarsego Padova 35011 Italy 3904 9920 2297 www baumatic it Holland Baumatic Benelux B V Grindzuigerstraat 22 1333 MS ALMERE The Netherlands 3136 549 1555 www baumatic nl 37 38 39 Baumatic www baumatic com
22. p you to sort your laundry into different loads depending on the fabric type and the highest temperature which the garment can be washed at o If the wash care label does not appear in the above table then please refer to the washing machine program chart This gives more detailed descriptions of the types of fabric that are suitable to be washed using a particular wash program 13 Detergents and conditioners The amount of detergent that you need to use in your appliance will depend on o The degree of soiling Lightly soiled garments in general require less detergent o The size of the wash load A smaller wash load will require a reduction in the amount of detergent o The hardness of your tap water The harder your water is then the more detergent you will need to use The detergent manufacturers normally give guidance as to how much extra detergent should be used depending on the hardness of the water Liquid detergent If you are using liquid detergent then in the majority of cases the liquid should be placed inside the dosing device supplied by the detergent manufacturer All instructions on the detergent packaging should be followed Water softening agents If your tap water is hard then it may be prudent to utilise a water softening agent This will help to ensure that the appliance does not become clogged with hard water deposits You may also find that it will allow you to lessen the amount of deterg
23. sh performance by extending the wash program that you have selected LCD display WwW WwW 5a 1100 058 be 1 Wash program phases Prewash Wash Rinse Spin and drain Drying CoO0O00 0 2 Spin speed 3 Program number for a few seconds and then program duration 4 Program options o Easy iron o Extra rinse o Intensive wash Detergent drawer WAV PREWNAZH WASH FABRIC SOFTENER Pre wash section uy This compartment should have detergent placed in if you are going to select a wash program that has a pre wash as part of it Main wash section ul This compartment should have detergent placed in it you should also put a water softening agent in this section if you use one The detergent will be added to the drum at the start of the main wash program Conditioner section ep This compartment should be used for liquid conditioners fabric softener starch They will be added to the wash load during the final rinse Preparing the wash cycle Preparing your garments for washing O Your washing should be sorted out according to the fabric type and the wash care symbol that is printed on the garment s wash care label see separate section on wash care symbols Your washing should also be sorted out according to the degree of soiling Check all pockets on a garment to make sure that they are empty Remove any detachable metal items badges
24. sult Child Safety O O O Your washing machine should only be used by adults You should not allow children in the area of the machine unsupervised You should not let them touch the controls or play with the appliance It could be possible for a child or pet to gain access to the washing machine through the porthole door Therefore please check the drum before using the appliance Any packaging that is removed from the machine should be kept away from children All detergents should be kept out of children s reach in a safe place Specifications Y Y 13 wash programs 2 drying programs 6kg wash load 3kg drying load 1100 rpm maximum spin speed LCD display Delay start timer with remain time indicator 3 Option buttons Easy iron Extra rinse Intensive wash Unbalance control system Foam protection Suspend the clothes in water option Door safety lock Child lock Stainless steel drum Adjustable feet Error code failure system Aqua Spray rain shower effect This additionally showers the wash load throughout the wash cycle It helps to improve the wash and rinsing efficiency Appliance dimensions Aperture dimensions Height 820 850 mm 820 mm Width 590 mm 600 mm Depth 550 mm 600 mm Energy efficiency Energy rating Wash performance Water extraction performance OD U Description of the appliance Drain hose Porthole Adjustable feet Control panel Detergent
25. to complete The LCD display will update to reflect this change v Press the Start Stop button o After approximately 5 seconds you will hear your washing machine start the wash cycle o Ifthere is a power failure or the plug is pulled out of the socket when a wash cycle is in progress The wash program will continue once power has been restored o Whilst the wash program is Uu J ut iur in progress the program ee NN phase and time remaining to mn i the end of the wash cycle will at F j T c appear on the display o The active phases will appear at the top of the display as the wash program progresses The time remaining until the end of the program will update throughout the wash cycle Please note that it does not count down in real time o Any program option can be selected once the wash cycle is already in progress providing that the stage in the wash cycle that the option will affect has not already passed E g you cannot select an intensive wash once the machine has reached the rinse stage of the wash cycle Selecting a separate drying program Y Activate the pop out program selector knob by depressing it o Select the most appropriate drying cycle for the garments that you wish to dry by turning the program selector knob o IMPORTANT Please take note of the maximum size of load that you can dry in this appliance This information is contained in the program chart o Select the drying time i
26. uction feature o Important You should make sure that the selected spin speed is appropriate for the garments that you are washing o If you use the spin reduction feature you can make the machine not go into a spin cycle If you pick this option then the machine will stop with water in the drum o Important Before opening the door of the appliance you MUST select the drain program to clear this water o The LCD display shows an approximate time for the selected wash cycle Please note that factors external to the machine e g the temperature of your water supply your water pressure etc can affect the time it takes for the wash cycle to complete Selecting a wash program Y Load your laundry and put detergent in the relevant compartment of the soap drawer Y Close the porthole door firmly Y Activate the pop out program selector knob by depressing it Y Select the most appropriate wash program for the garments that you are washing by turning the program selector knob o The LCD display will briefly flash the wash program number that you have selected and then show the approximate time that it will take the chosen wash cycle to complete Y Select any program options by using the program option button underneath the LCD display for more information please refer to the setting a program option section o Any program option that you select will affect the length of time that the wash cycle will take
27. y FO2 The machine will not drain or spin o Clean the drain pump filter o Check the drain hose is not blocked or kinked F04 The machine does not start o Check that the door has been shut properly before commencing a wash cycle c03 The machine has sensed an out of balance load o This may be due to uneven distribution of clothes in the drum which may cause an excessive level of vibration o Seethe General troubleshooting section FO5 F10 Contact Baumatic Service Department Once the machine has been plugged back into your mains power supply to clear the fault code from the LCD display you should turn on the machine and hold down the Start Stop button for approximately 5 seconds 26 If a fault code reappears after following the above advice and clearing the fault code You should turn the wash program selection knob to the off position Disconnect the appliance from your mains supply Then arrange for an engineer to attend the appliance You should contact the Baumatic Service Department on 0118 933 6911 IF AN ENGINEER ATTENDS DURING THE GUARANTEE PERIOD AND FINDS THAT A FAULT HAS BEEN CAUSED BY AN ITEM ON THE ERROR CODE LIST WHICH COULD HAVE BEEN CLEARED BY THE CUSTOMER THEN YOU MAY BE LIABLE FOR THE COST OF THE SERVICE CALL General troubleshooting Water under the washing machine o Tighten the drain pump filter o Check the drain and inlet hose and make sure that it is fully tightened
Download Pdf Manuals
Related Search