Home

Siig UltraATA 133 PCI RAID

1. connector of cable and set it as master If you have a second hard disk drive connect it to the middle connector of cable and set it as slave End Connector Middle Connector Internal Drive 1 Drive 1 Drive 2 UltraATA 133 PCI RAID Internal Drive 2 If Any Figure 3 Connecting Internal Drives 4 Reconnect the system power and other peripherals to your computer RAID Arrays RAID Arrays are setup in the UltraATA 133 PCI RAID BIOS Find your RAID set and follow the steps in the order in which they appear RAID 0 Striping This RAID array to be used on New Blank hard drives Striping will destroy existing data on the hard drive For Manual Setup 1 As the BIOS boots press F3 when prompted to enter the RAID BIOS 2 At the next screen press F2 to form a RAID set 3 Press F1 to create RAID 0 4 Choose the chunk size to be used in the RAID set 64 is recommended 5 Choose the number of hard drives in your stripe set 6 Assign the hard drives to be used For optimal performance alternate hard drives from seperate IDE channels 7 After all hard drives are entered press Y to create the RAID set 8 Press ESC to exit the RAID BIOS and boot your computer 9 Continue with Fdisk and Format steps as if you are installing a conventional hard drive For Auto Setup 1 piso Bis wee PS As the BIOS boots press F3 when prompted to enter the RAID BIOS Press F2 to create a RAID set Press F
2. RAID set it s best to install the hard drives on separate channels either Master to Master or Slave to Slave For example if you are setting up a RAID set with two hard drives install the first drive on IDE1 as Master and the second on IDE2 as Master Use the same concept for multiple hard drives Note Only the 40 pin 80 wire UltraATA cable can achieve hard disk UDMA 133 performance When attaching only two hard drives it is recommended that they be connected on separate IDE channels 1 If you plan to install two hard disk drives on the IDE1 channel make sure to configure one drive as Master and the drive as Slave Follow the hard drive manufacturer s instructions for the correct jumper setting The same rule must be followed for connecting hard disk drives to the IDE2 channel 2 Attach one end of the included Ultra ATA cable to the IDE1 connector on the board Make sure pin 1 on the cable indicated by the stripe matches pin 1 on the IDE1 connector Stripe Figure 2 Connecting the Cable to the On Board Connector 3 Install the hard disk drive to your computer Attach the end connector of the Ultra ATA cable to the connector on the hard disk drive Make certain that pin 1 on the cable indicated by the stripe matches pin 1 on the hard disk drive s connector The same procedure applies when making connection to IDE2 Note The ribbon cable has two connectors If you have one hard disk drive connect it to the end
3. and the name of the file as well Audio The user may set different audio alerts for the different levels of events 31 Popup The popup window is a visual notification that an event occurred The popup window can be disabled or set to popup for only certain event levels P costinraten tims SMTP Eve Aoticatio Bartle Pon The different levels are Disabled No popup will occur Informational The popup window will be displayed for the following events Informational Warnings Errors Warning The popup window will be displayed for the following events Warnings Errors Errors The popup window will be displayed for the following events Errors 32 Blank Page 33 34 Blank Page Technical Support and Warranty QUESTIONS SIIG s Online Supporthas answers Simply visit our web site at www siig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away Youcanalso submit questions online and a technical support analysts will promptly respond SiG offers a lifetime manufacturer warranty with this product Please see our web site for more warranty details If you encounter any problems with this product please follow the procedures below A If it is within the store s return policy period please return the product to the store where you purchased from B If your purch
4. be sent via e mail Using the e mail tab in the Medley Configuration Menu the user may set the default e mail address and subject line to where the configuration would be sent This however can be overridden at the time of sending the email Ss as I ighe l ab o m Bp Eei a Emaii E aai rasai sds corigaes ines Fie rend mbes he erage ira od Eom Lon dagen Eai Sy Cora irer ee g Notification When different types of events occur Medley may be configured to send notices to assigned individual e mail addresses Using the Notification tab all e mail addresses desired to receive the notices may be entered wW iien psi iomar h mr ro rase mpide imr pn thereat eg k ri mare Hsk alja fee Katee php moet Saimi Raw ud 29 Event Level There are different types of e mail notifications that may be sent which are set with the Event Level tab Conhgurstion Meni ee 7 The different levels are Disabled No event logs will be sent Informational The following events will be sent Informational Warnings Errors Warning The following events will be sent Warnings Errors Errors The following events will be sent Errors 30 Log File The log file is used to store event information received fromall the RAID drivers The log file is a text file and can be viewed with Notepad or the Medley GUI Use the Log File tab to set where the log file should be stored
5. to Medley GUI on page 22 and install the RAID monitoring utility For Existing Windows ME Installation 1 Setup the RAID array prior to driver installation and boot up to Windows Atthe Add New Hardware Wizard insert the driver CD Select Automatic search for a better driver Recommended then click Next Click Finish remove the driver CD then click Yes to restart Windows to complete the installation To Verify Windows 98SE ME Installation 1 Right click My Computer click Properties then click Device Manager Double click SCSI Controllers Silicon Image Sil 0680 Ultra 133 Controller should be displayed 3 Highlight Silicon Image Sil 0680 Ultra 133 Controller and click Properties A message This device is working properly is displayed the driver has been correctly installed Windows NT 4 0 For A New Windows NT 4 0 Installation A new installation of Windows NT 4 0 requires a floppy disk for the driver installation To make this floppy disk copy the contents of the 32bit folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Setup the RAID array prior to NT installation 2 Follow Microsoft s NT installation procedure 3 Whenbooting from Microsoft Windows NT 4 0CD the following screens will appear 4 Screen 1 Setup is inspecting your computer s hardware configuration press F6 key to specify and add the driver 5 Screen 2 Windows NT Setup Setup is loa
6. 1 to create a Stripe set Press A for Auto Setup Enter the number of hard drives in the stripe set Press Y to accept the configuration Configure another RAID set or press ESC to reboot RAID 1 Mirror For Manual Setup For New Blank hard drives 1 g oo N 10 As the BIOS boots press F3 when prompted to enter the RAID BIOS At the next screen press F2 to form a RAID set Press F2 to create RAID 1 Ina Mirror set the source drive needs to be equal to or smaller than the destination drive For optimal performance the source drive and destination drive should be on separate IDE channels Answer N to Auto Setup Assign Source drive then assign Destination drive Answer N when asked to Copy from Source to Destination Answer Y to Enable Auto Rebuild When asked Are you Sure press Y to accept Press ESC to exit the RAID BIOS and boot the computer Continue with Fdisk and Format steps as if you were installing a conventional hard drive For Existing Hard Drives with Data 1 Nay he ee As the BIOS boots press F3 when prompted to enter the RAID BIOS Press F2 to enter the RAID setup screen Press F2 to form Raid set 1 mirror Answer N to Automatic setup Assign Source drive then assign Destination drive Press Y to copy from Source to Destination drive Press N to Offline copy 10 Answer Y to Enable Auto Rebuild When asked Are You Sure press Y to accept Press ESC to exit the RAID BIOS I
7. T 4 0 Installation 1 Go to Start Settings Control Panel double click SCSI Adapters icon Highlight Silicon Image Sil 0680 Ultra 133 Medley ATA RAID Controller from SCSI Adapters listing and select Properties A message This device is working properly is displayed in the dialog box the driver has been correctly installed Windows 2000 For New Windows 2000 Installation A new installation of Windows 2000 requires a floppy disk for the driver installation To make this floppy disk copy the contents of the 32bit folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Setup the RAID array prior to Windows installation 2 Follow Microsoft s Windows 2000 installation procedure 3 Restart the computer when prompted 4 Atthe Windows 2000 Setup screen when prompted press F6 to install the driver 5 When prompted press S to specify the location of the driver 6 Insert the driver diskette then press Enter 7 Silicon Image Ultra 133 Medley ATA RAID Controller will appear in the box press Enter 8 Press Enter to finish driver installation then follow the on screen instructions to complete Windows 2000 installation When Windows installation completes go to Medley GUI on page 22 and install the RAID monitoring utility For An Existing Windows 2000 Installation 1 Setup the RAID array prior to driver installation and boot up to Windows At the Found New Hardware Wiz
8. ard click Next Select Search for a suitable driver for my device recommended then click Next Insert the driver CD check CD ROM drives uncheck the other boxes click Next and click Next again 17 Ifthe Digital Signature Not Found message appears click Yes Our driver has been thoroughly tested in Windows for stability Note If prompted for Windows 2000 CD ROM insert the CD into your CD ROM drive and click OK Type in D I386 change D to match your CD ROM drive letter click OK then Finish Click Finish remove the driver CD then restart Windows to complete driver the installation When Windows resumes go to Medley GUI on page 22 and install the RAID monitoring utility 32 bit Windows XP Server 2003 For A New 32 bit Windows XP Server 2003 Installation A new installation of Windows XP Server 2003 requires a floppy disk for the driver installation To make this floppy disk copy the contents of the 32bit folder found on the driver CD onto a blank floppy disk then follow the directions below 1 2 3 Setup the RAID array prior to Windows installation Follow Microsoft s Windows installation procedure Restart the computer when prompted by Windows installation At the Windows Setup screen when prompted press F6 to install the driver When prompted press S to specify the location of the driver Insert the driver diskette then press Enter Silicon Image Ultra 133 Medley ATA RAID Cont
9. are drive to a Mirrored set that has experienced a disk failure If more than one set exists clicking on each Setin the Configuration Tree provides specific information for that Set CITES i HTS ES lian 26 The device identification along with the State of each device is also reported in the Members tab window Note that when a Mirrored Set is first created the State of the destination drive may report as Rebuild for as muchas 30 90 minutes depending on the size of the disk SMART and Configuration information as well as Data Identification is again provided for each Set Medley Configuration Menu With Medley running the small Medley icon should appear in the bottom right of the computer screen next to the clock By right clicking on the icon the user may configure Medley including customizing the settings for SMTP E mail Notification Event Level Log File Audio and Popup SMTP The SMTP server is the server that is used to send e mails Normally the network administrator knows what this name is Both the name and domain must be entered E bel LogFie hudo Ppp SMTP Ema Hotficaion EverdLevel SMTP inkara ASM TP Hh it it sree Dat i ubi lo bared a rea Contest your pice ak Woe EI tune i Ee npe bo reiua the raii and dover Esarpa SAS Oh oo r SHTF Conigaston SMTP Serer ii lt 28 E Mail The current Medley configuration may
10. ase has passed the store s return policy period please follow these steps to have the product repaired or replaced Step 1 Submit your RMA request Go to wwwsiig com click Support then RMA to submit a request to SIG RMA If the product is determined to be defective an RMA number will be issued SIIG RMA department can also be reached at 510 413 5333 Step 2 After obtaining an RMA number ship the product e Properly pack the product for shipping All software cable s and any other accessories that came with the original package must be included e Clearly write your RMA number on the top of the returned package SIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e Youare responsible for the cost of shipping Ship the product to the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA e SIIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer 35 About SIIG Inc Founded in1985 SHG Inc isaleading computer upgrade manufacturer of I O connectivity products including PCI amp ISA serial and parallel ports USB Serial ATA amp UltraATA controllers FireWire 1394a b networking sound cards and other accessories SIIG is the premier one stop source of upgrades SIIG products offer co
11. ding files keep pressing F6 key to add driver 6 If screen 3 does not appear for options to Specify Additional Device then shut off system and repeat steps 4 5 otherwise continue to step 7 7 Insert the driver diskette and press S 8 Screen 4 Windows NT Setup highlight Other and hit Enter 9 Screen 5 Windows NT Setup make sure driver diskette is in floppy drive and press Enter 10 Screen 6 Windows NT Setup highlight Silicon Image Ultra 133 Medley ATA RAID Controller and hit Enter to load driver 11 Follow on screen instructions to complete setup for your NT version When Windows installation completes go to Medley GUI on page 22 and install the RAID monitoring utility For An ExistingWindows NT 4 0 Installation 1 7 Setup the RAID array prior to driver installation and boot up to Windows NT Double click My Computer Control Panel SCSI Adapters then click on the Drivers tab Select Add then Have Disk Insert the driver CD type in D 32bit change D to match CD ROM then click OK Highlight Silicon Image Sil 0680 Ultra 133 Medley ATA RAID Controller and click OK Click Browse then click drop down arrow in Look in Select CD ROM drive Drivers double click 32bit click Open then OK Remove the driver CD close all open Windows then restart NT to complete the installation When Windows resumes go to Medley GUI on page 22 and install the RAID monitoring utility To Verify Windows N
12. f UltraATA 133 PCI RAID o Quick Installation Guide Introducing the UltraATA 133 PCI RAID The UltraATA 133 PCI RAID is a ultra high speed dual channel Ultra ATA 133 controller for use in Pentium class computers It achieves burst data transfer rates up to 133MB sec and supports drive capacities greater than 137GB It s enhanced BIOS auto detects device types and fine tunes to the best performance for each connected hard drive Features and Benefits Compliant with UltraDMA6 ATA 133 specifications Compliant with PCI v2 2 Plug n Play Provides two independent Ultra ATA channels built in 256 byte FIFOs per channel for faster data transfer Supports Ultra DMA 0 6 and Multi word DMA 0 2 Breaks the 137GB barrier Supports hard drives larger than 137GB Co exists with on board IDE controller Supports RAID 0 striping RAID 1 mirroring and RAID 0 1 mirror striping CRC Cyclical Redundancy Check error checking provides data verification and achieves flawless data transfer Full ACPI power management support Flash BIOS for easy upgrade Works with various brands of Ultra ATA 133 100 66 33 hard disk drives 04 0369B 1 System Requirements e Pentium class computer with one available PCI slot e Windows 98SE ME NT 4 0 2000 XP 32 64 bit Server 2003 32 64 bit Package Contents e UltraATA 133 PCI RAID controller e Two 40 pin 80 wire Ultra ATA cables e Two Y split power cables i Software Driver CD e Quick Instal
13. gnore the BIOS error message and continue booting The mirror rebuilds automatically For Auto Setup Use this setup on New Blank hard drives only 1 eer eS As the BIOS boots press F3 when prompted to enter the RAID BIOS Press F2 to create a RAID set Press F2 to create a Mirror set Press Y to use Auto setup Press Y to accept the configuration Configure another RAID set or press ESC to reboot Continue with Fdisk and Format steps as if you were installing a conventional hard drive Creating a SPARE Drive When a hard drive failure occurs in a mirror set the auto rebuild feature enables a drive designated as SPARE to become the new member of the mirror set 1 2 3 4 5 As the BIOS boots press F3 when prompted to enter the RAID BIOS Press F3 to create a spare drive Enter the drive number of the hard drive Press Y to confirm your choice The spare drive will be created and listed as the last set Press ESC to exit the RAID BIOS The SPARE drive will not be seen by Windows however it remains in the background waiting to rebuild the mirror in the event of a hard drive failure 8 Rebuilding a Failed Mirror Set IfaSPARE drive was not configured the steps below will guide you in rebuilding a failed mirror set 1 10 11 12 13 14 15 16 17 As the BIOS boots press F3 when prompted to enter the RAID BIOS Press F1 to dissolve an Array Press the number of the Mirr
14. ing the GUI the the first window which identifies the computer running Medley should appear similar to the following 22 Selecting each different component in the configuration tree provides specific information for that component such as the chip By selecting a specific channel either Primary or Secondary the following information is reported Whaat SME SITE EST Got 23 Selecting aspecific drive reports all pertinent information to that drive including Configuration and Disk Identification information ENITI Inii pIIe ray Cea eres oa ba COR a Fp E lier 24 Selecting Sets reports how many RAID sets have been created tality im he ile BEDE all RF Po aed i hea Hara Sus G iao Have T ia TE aio tert By selecting a specific RAID set such as Set 0 which is the Striped set the type of RAID set the number of members and stripe size is reported Goa at Tc T Ga Mera SUNT Corie icky Date Ee PL CLA T BLATA biped Fa Tr Litle Hire Uwe dete f Leo Freep Are kasam Z0 Cy miian miket SNTE Zh Frm 25 The Members tab reports the device identification corresponding with the information in the BIOS and the State of each device Sole BAR HITED be fal Besides reporting information the Members tab of a mirror set allows the user to remove a specific drive from that set as well as add a designated Sp
15. iver installation To make this floppy disk copy the contents of the 64bit folder found on the driver CD onto a blank floppy disk then follow the directions below 1 Setup the RAID array prior to driver installation and boot up to Windows Install the board and follow Microsoft procedures to install Windows accordingly Restart your system when prompted during Windows installation At the Windows Setup screen press F6 to install the driver Insert the driver diskette Press S then press Enter Select Silicon Image Sil 0680 ATA 133 RAID Controller 64 bit Extended and press Enter Press Enter to continue and follow on screen instructions to complete the installation When Windows resumes go to Medley GUI on page 22 and install the RAID monitoring utility For Existing 64 bit Windows XP Server 2003 Installation 1 20 Setup the RAID array prior to driver installation and boot up to Windows Install the board and boot up Windows At the Found New Hardware Wizard XP w SP1 or earlier Server 2003 continue to step 4 XP w SP2 or later Server 2003 w SP1 or later select No not at this time then click Next Insert the driver CD select Install the software automatically Recommended then click Next Note Most systems will install the driver automatically after inserting driver CD Click Finish remove the driver CD and restart Windows to complete the installation When Windows resumes go to Medle
16. lation Guide Layout Pin1 IDE2 Pin1 IDE1 HDD Activity LED Jumper On do not remove Figure 1 UltraATA 133 PCI RAID layout Note For proper operation of the UltraATA 133 PCI RAID the jumper must remain on Hardware Installation General instructions for installing the card are provided below Since the design of computer cases and motherboards vary refer to your computer s reference manual for further information if needed Static Electricity Discharge may permanently damage your system Discharge any static electricity build up in your body by touching your computer s case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges 1 Turn OFF the power to your computer and any other connected peripheral devices 2 Unplug the power cord from the back of the computer 3 Remove your computer s cover 4 Remove the slot bracket from an available PCI slot 5 To install the card carefully align the card s bus connector with the selected PCI slot on the motherboard Push the board down firmly but gently until it is well seated 6 Replace the slot bracket s holding screw to secure the card Device Connection The UltraATA 133 PCI RAID isa dual channel Ultra ATA 133 controller that supports up to four IDE hard disk drives To achieve maximum performance and compatibility we suggest using identical hard drives in building your RAID sets In any given
17. mprehensive user manuals many user friendly features and are backed by an extensive manufacturer warranty High quality control standards are evident by the overall ease of installation and compatibility of our products as well as one of the lowest defective return rates in the industry SIIG products can be found in computer retail stores mail order catalogs through major distributors system integrators and VARs in the Americas and the UK and through e commerce sites PRODUCT NAME UltraATA 133 PCI RAID FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCESTATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SHG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA UltraATA 133 PCIRAID isa trademark of SIG Inc SIIG and the SIIG logo are registered trademarks of SHG Inc Microsoftand Windowsare registered trademarks of Microsoft Corporation Pentiumis aregistered trademark of Intel Corporation Othernames used in this publication are foridentification only and may be trademarks of their respective companies July 2007 Copyright 2007 by SIIG Inc All rights reserved
18. nation drive 7 Enter Y to accept the RAID configuration 8 On the following screen press ESC to exit the RAID configuration utility and reboot the computer 9 Continue with Fdisk and Format steps as if you were installing a conventional hard drive For Auto Setup 1 As the BIOS boots press F3 when prompted to enter the RAID BIOS Press F2 to create a RAID set Press F3 to create a Mirrored Striped set a So S Press A to Auto configure Press Y to accept the configuration Press ESC to reboot Continue with Fdisk and Format steps as if you were installing a conventional hard drive Rebuilding a Failed RAID 0 1 Set The steps below will guide you in rebuilding a failed Mirrored Stripe set 1 ON Ee Replace the failed drive with one of identical size or of larger capacity Note It is recommended to replace the bad drive with an identical drive or with a drive of the same make In all cases the replacement drive must be of equal or larger capacity than the bad drive Start the computer and during boot press F3 when prompted to enter the RAID BIOS Press F3 to assign a Spare drive Press the number corresponding to the new drive When asked Are You Sure Press Y to accept Press ESC to exit the RAID BIOS and reboot the computer Note Ignore the error message displayed by the RAID BIOS and continue booting The mirror will rebuild automatically Deleting RAID Arrays 1 As the BIOS boo
19. ored array to be dissolved Press Y to confirm Be sure you delete the correct Array Press ESC to exit the RAID BIOS then immediately turn off the computer Replace the bad drive with a new hard drive of equal or greater size then restart the computer During boot press F3 to enter the RAID BIOS Press F2 to Create an Array Press F2 to create a Mirrored Array Answer N for Automatic setup Enter the number of the SOURCE good drive Enter the number of the DESTINATION new drive Answer Y to copy from Source to Destination drive Answer N to decline Offline Copy Answer Y to enable Auto rebuild When asked Are You Sure Press Y to accept Press ESC to exit the RAID BIOS and reboot the computer RAID 0 1 Mirror Striping This RAID array to be used on New Blank hard drives only striping destroys existing data on the hard drive RAID 0 1 requires four hard drives For Manual Setup 1 As the BIOS boots press F3 when prompted to enter the RAID BIOS 2 At the next screen press F2 to form a RAID set 3 Press F3 to create RAID 0 1 4 Choose the chunk size by pressing the appropriate number key 64 is recommended 5 Enter the first Source drive then enter the second source drive Note To optimize performance configure both source drives to be from different channels and configure both destination drives tobe from different channels 6 Enter the first destination drive then enter the second desti
20. roller will appear in the box press Enter Press Enter to finish driver installation then follow the on screen instructions to complete Windows installation Note If the Software Installation warning pops up click Yes And ifthe Hardware Installation warning popsup click Yes again Our driver has been thoroughly tested for stability and compatibility When Windows installation completes go to Medley GUI on page 22 and install the RAID monitoring utility For Existing 32 bit Windows XP Server 2003 Installation 1 Setup the RAID array prior to driver installation and boot up to Windows Install the board and boot up in Windows At the Found New Hardware Wizard XP w SP1 or earlier Server 2003 continue to step 4 XP w SP2 or later Server 2003 w SP1 or later select No not at this time then click Next Insert the driver CD select Install the software automatically Recommended then click Next Note Most systems will install the driver automatically after inserting driver CD If the Windows logo window appears click Continue Anyway then click Finish to complete the installation Our driver has been thoroughly tested for stability and compatibility When Windows resumes go to Medley GUI on page 22 and install the RAID monitoring utility 64 bit Windows XP Server 2003 For New Windows 64 bit XP Server 2003 Installation A new installation of Windows XP Server 2003 requires a floppy disk for the dr
21. ts press F3 when prompted to enter the RAID BIOS Press F1 to dissolve a RAID set Enter the number of the RAID set to be deleted Answer Y to remove the RAID set Press ESC when finished to reboot Oe a cela Resolving Conflicts If after a disk failure the replacement disk was previously part of a RAID set or used in another system it may have conflicting metadata specifically in reference to the drive connection information If so this will prohibit the RAID set from being either created or rebuilt in order for the RAID set to function properly this old metadata must be first overwritten with the new metadata To resolve this press F4 the correct metadata including the correct drive connection information will be written to the replacement disk Software Installation This section provides information on how to install the UltraATA 133 PCI RAID drivers Windows 98SE For A New Windows 98SE Installation 1 Setup the RAID array prior to Windowsinstallation 2 Follow Microsoft procedures to install Windows 98SE accordingly 3 Once Windows has installed and booted right click My Computer and click Properties Select Device Manager tab DD ON GI Double click PCI RAID controller listed under Other Devices Select Driver tab then click Update Driver button Insert the driver CD then click Next Select Search for the better driver and click Next Check Specify a location uncheck the other boxes t
22. y GUI on page 22 and install the RAID monitoring utility To Verify Windows 2000 XP Server 2003 Installation 1 Right click My Computer click Manage then click Device Manager Double click SCSI and RAID Controllers 32 bit Windows 2000 XP Server 2003 You should see Silicon Image Sil 0680 Ultra 133 Medley ATA RAID Controller 64 bit Windows XP Server 2003 You should see Silicon Image Sil 0680 ATA 133 RAID Controller Double click each category to display driver properties A message This device is working properly is displayed the driver has been correctly installed 21 Medley GUI The Medley GUI provides significant functionality including the ability to create and dissolve RAID sets Remove a member of a Mirrored or Mirrored Striped RAID set Rebuild a Mirrored RAID set save copy or send via e mail the current configuration Installing Medley GUI 1 Place the driver installation CD into the CD ROM drive 2 At the Windows desktop click Start then Run 3 Type D Installsiicfg exe then click OK 4 Click Next Next then Finish respectively The installation of the Medley GUI is now complete Proceed to Using the Medley GUI for operating instructions Using Medley GUI During the installation process the Medley GUI was saved in the Windows Startup folder a small blue Medley logo will appear in the right hand corner of taskbar To launch the GUI simply click on the icon Upon launch
23. ype in D 32bit change D to match CD ROM then click Next Click Next again Click Finish remove the driver CD then click Yes to restart Windows to complete the installation When Windows resumes go to Medley GUI on page 22 and install the RAID monitoring utility For Existing Windows 98SE Installation 1 Setup the RAID array prior to driver installation and boot up to Windows At the Add New Hardware Wizard click Next to continue Select Search for the best driver for your device then click Next Check Specify a location uncheck the other boxes type in D 32bit change D to match CD ROM then click Next Click Next again Click Finish remove the driver CD then click Yes to restart Windows to complete the installation When Windows resumes go to Medley GUI on page 22 and install the RAID monitoring utility Windows ME For A NewWindows ME Installation 1 2 7 Setup the RAID array prior to Windows installation Follow Microsoft procedures to install Windows ME accordingly Once Windows has installed right click My Computer and click Properties Select Device Manager tab Double click PCI RAID controller listed under Other Devices Select Driver tab and click Update Driver button Insert the driver CD select Automatic search for a better driver Recommended then click Next Click Finish remove the driver CD then click Yes to restart Windows to complete the installation When Windows resumes go

Siig UltraATA 133 PCI RAID

Contents

Download Pdf Manuals

Related Search

Related Contents